Toggles Series NP01 Rockers General Specifications Electrical Capacity (Resistive Load) Contact Resistance: 50 milliohms maximum Insulation Resistance: 500 megohms minimum @ 250V DC Dielectric Strength: 250V AC minimum between contacts for 1 minute minimum Mechanical Life: 500,000 operations minimum Electrical Life: 500,000 operations minimum Nominal Operating Force: Standard: 1.5N ±0.5 Newtons High: 2.5N ±0.8 Newtons Stroke: 1.5mm (.059”) D Materials & Finishes Actuator: Case: Base: Movable Contact: Stationary Contacts: Switch Terminals: Operating Temperature Range: Humidity: Vibration: Tactiles Slides Environmental Data Tilt Installation Cap Installation Force: Touch 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Other Ratings Rotaries Keylocks Programmable Illuminated PB Pushbuttons Logic Level: Shock: PCB Processing Soldering: Cleaning: Standards & Certifications Silicon rubber Polycarbonate resin Glass fiber reinforced polyamide resin Silver over nickel with gold plating Brass with gold plating Brass with gold plating –25°C through +50°C (–13°F through +122°F) for Illuminated –25°C through +70°C (–13°F through +158°F) for Nonilluminated 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) 5.0N maximum downward force on actuator Wave Soldering: 270°C maximum @ 6 seconds maximum Manual Soldering: 390°C maximum @ 4 seconds maximum These devices are not process sealed. Hand clean locally using alcohol based solution. The NP01 Series pushbuttons have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. Supplement Accessories Indicators Subminiature Smooth Actuation Pushbuttons D74 www.nkkswitches.com 7/19/17 Series NP01 Toggles Subminiature Smooth Actuation Pushbuttons Rockers Distinctive Characteristics Distinct, long stroke of 1.5mm (.059”). Entire cap is fully illuminated with single or bicolor LED. D Compact design with dimension of 12.5mm (.492”) from PC board to top of cap. Keylocks Alternating legend options with bicolor LED. Programmable Illuminated PB Pushbuttons Soft touch actuation achieved by mechanical silicon rubber structure. Rotaries Available in both high (2.5N) or standard (1.5N) operating force. Slides Gold plated contacts provide high reliability. Tactiles Crimped terminals ensure secure PC mounting and prevent dislodging during soldering. Touch Tilt Molded-in terminals prevent entry of flux, solvents, and other contaminants. Supplement Accessories Indicators Actual Size www.nkkswitches.com D75 Series NP01 Toggles Subminiature Smooth Actuation Pushbuttons TYPICAL SWITCH ORDERING EXAMPLE 15 Pole & Circuit 15 D SPST OFF H G03 L Contacts & Terminals (ON) ( ) = Momentary Normally Open Contacts G03 Operating Force Gold Contacts and PC Terminals, Rated 0.4VA @ 28V AC/DC L Illuminated N Nonilluminated Cap Lens/Diffuser Colors Single or Bicolor LED H High (2.5N) (Gray Switch Body) C Red D Amber F Green CF Bicolor Red/Green DG Bicolor Amber/Blue JB Clear/White (Combine with any LED) JC Clear/Red JD Clear/Amber JF Clear/Green Bicolor Alternating Legend Caps Slides Bicolor LED CF Red/Green DG Amber/Blue Tactiles Tilt Packaging No Code Partitioned Tray, Any Quantity (With or without caps installed) S Stick-Tube 50 Pieces/Stick (For switch body only; caps packaged separately) Alternating Legends 11 ON (pos) Red/Green 12 ON (neg) OFF (neg) JDG Amber/Blue 13 START STOP 14 OPEN CLOSE Solid Color Cap A Black B White C Red H Gray Contact factory for custom options. Touch Part Numbers for Alternating Legends Color Part Number Red/Green AT3023JCF11 ~ AT3023JCF14 Amber/Blue AT3023JDG11 ~ AT3023JDG14 Indicators Refer to Ordering Table for Alternating Legend that corresponds with last 2 digits of part number. DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Accessories NP0115HG03LF-JF High (2.5N) Operating Force Supplement SPST OFF-Momentary ON Circuit Normally Open Contacts D76 OFF (pos) JCF Nonilluminated No LED JF Illumination Cap Types & Colors Standard (1.5N) (Black Switch Body) N F LEDs A Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers NP 01 www.nkkswitches.com Clear Lens with Green Diffuser Green LED Gold Contacts with 0.4VA Rating Straight PC Terminals Series NP01 Toggles Subminiature Smooth Actuation Pushbuttons POLE & CIRCUIT SP Down Notes: Switch is marked with LC1, 1, L3, L4, L1, L2, 2, LC2. Lamp circuit is isolated and requires an external power source. Model NP0115AG03L NP0115HG03L OFF (ON) Normally Open D 1-2 SPST 1 (+) 2 (-) ( ) = Momentary Normal Down Note: Switch is marked with LC1, 1, L3, L4, L1, L2, 2, LC2. Model NP0115AG03N NP0115HG03N OFF (ON) Normally Open 1-2 Slides SP Throw & Switch Schematic SPST 1 2 Tactiles Pole Connected Terminals Keylocks Nonilluminated Models Plunger Position Standard Nominal Operating Force H Tilt OPERATING FORCE High Nominal Operating Force 1.5 ±0.5N 2.5 ±0.8N Switch base is Black Switch base is Gray Touch A Pushbuttons Pole Throw & Switch Schematic Programmable Illuminated PB Normal Connected Terminals Rotaries Plunger Position ( ) = Momentary Rockers Illuminated Models Gold Contacts Straight PC Terminals 0.4VA maximum @ 28V AC/DC maximum Accessories G03 ILLUMINATION Illuminated N Nonilluminated www.nkkswitches.com Supplement L Indicators CONTACTS, TERMINALS, & RATING D77 Series NP01 Toggles Subminiature Smooth Actuation Pushbuttons LED COLORS & SPECIFICATIONS D Tactiles VF E E – VF R = Anode Cathode – Where: R = E = VF = IF = IF Resistor Value (Ohms) Source Voltage (V) Forward Voltage (V) Forward Current (A) Bicolor LED D F Red Amber Green Red Green Amber Blue Maximum Forward Current IFM 30mA 30mA 25mA 30 (25)mA 25 (25)mA 30mA 30mA Typical Forward Current IF 20mA 20mA 16mA 20 (20)mA 16 (5)mA 20mA 20mA Forward Voltage VF 1.95V 2.0V 3.3V 1.95V 3.3V 2.0V 3.2V Maximum Reverse Voltage VRM 5V 5V 5V 5V 5V 5V 5V Current Reduction Rate ∆IF 0.41mA/°C above 25°C 0.38mA/°C above 25°C 0.33mA/°C above 25°C 0.40mA/°C above 25°C 0.33mA/°C above 25°C 0.40mA/°C above 25°C 0.40mA/°C above 25°C Color Ambient Temperature Range Amber LED CF L3 (-) L2 (-) LC1 (+) DG –25° ~ +50°C –25° ~ +50°C L4 (-) LC2 (+) Red or Green LEDs L2 (-) LC1 (+) L1 (-) Red/Green Bicolor LED L4 (-) Green LC2 (+) L3 (-) Red Amber/Blue Bicolor LED L2 (-) Red LC1 (+) L1 (-) L4 (-) Blue LC2 (+) L3 (-) Amber L2 (-) Amber LC1 (+) L1 (-) Green L1 (-) Blue CAP TYPES & COLORS (12.0) Sq .472 AT3022 12mm Square Cap Cap for Single or Bicolor LED (10.2) .402 Tilt (12.0) Sq .472 AT3023 12mm Square Cap Touch IF + C Material: Polycarbonate Resin JB Clear Lens/White Diffuser JD Clear Lens/Amber Diffuser JC Clear Lens/Red Diffuser JF Clear Lens/Green Diffuser Alternating Legend Cap for Bicolor LED (10.2) .402 Material: Polycarbonate Resin JCF Red/Green JDG Amber/Blue Clear Lens Alternating Legend Filter Standard Alternating Legend Pairs 11 Accessories Indicators R Single Color LED ATTENTION ELECTROSTATIC SENSITIVE DEVICES Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers LEDs are an integral part of the switch and not available separately. The electrical specifications shown are determined at a basic temperature of 25°C. If the source voltage exceeds the forward voltage, a ballast resistor is required. Specifications in parentheses ( ) below for Bicolor LED denote simultaneous illumination of Red and Green. ON OFF Supplement Green/Red or Blue/Amber 12 ON OFF Green/Red or Blue/Amber 13 START STOP Green/Red or Blue/Amber Cap illumination is alternating Green/Red or Blue/Amber; legend text is black. Contact factory for other Alternating Legends. Legend illustrations are approximate representations of the actual characters on the filters. D78 www.nkkswitches.com 14 OPEN CLOSE Green/Red or Blue/Amber Series NP01 Toggles Subminiature Smooth Actuation Pushbuttons CAP TYPES & COLORS (CONTINUED) Solid Color Cap for Nonilluminated B H White Red Gray Pushbuttons Material: Polycarbonate Resin C Black TYPICAL SWITCH DIMENSIONS Illuminated • Straight PC (2.1) .083 (2.0) Typ .079 L4 L3 (10.2) .402 (12.5) .492 (12.0) Sq .472 1 LC1 LC1 1 L3 L4 (7.0) .276 LC2 2 L1 L2 2 LC2 (0.3) Typ .012 (0.5) Typ .020 (3.3) .130 L2 L1 CL (7.0) .276 (1.0) Dia Typ .039 (2.0) Typ .079 NP0115HG03LF-JF No Code Partitioned Tray Any quantity. No code is required. Switches may be packaged with or without caps installed. Stick-Tube Packaging Slides S Rotaries PACKAGING 50 pieces per stick (15.3) .602 (11.85) .467 Tactiles Switches must be ordered in 50-piece increments when stick-tube packaging is selected. This packaging is for the switch body only. Caps will be packaged separately. (470.0) 18.504 Bottom View Orient cap with legend as shown here, and “LC2” at lower right of switch body. LC1 1 L3 L4 L1 L2 2 LC2 LC2 Touch OPEN Tilt LEGEND ORIENTATION Top View D Programmable Illuminated PB A (10.2) .402 Keylocks AT3024 12mm Square Cap Rockers (12.0) Sq .472 Orders for switches with legends will be assembled as illustrated. ATTENTION Accessories ELECTROSTATIC SENSITIVE DEVICES Slot Supplement 1. NP01 Pushbuttons are electrostatically sensitive. To prevent damage to LED, devices must be properly isolated from static electricity. 2. Once the cap is installed onto the switch body, it cannot be removed. 3. When assembling cap, align projection on switch body to slot on inside of cap. (Refer to illustration at right.) 4. * Legends may be printed on the lens with laser etch, screen print or pad print methods. Epoxy based ink is recommended. 5. Do not use excessive force during installation on PC board or for cap installation. Indicators PRECAUTIONS FOR HANDLING & STORAGE Projection * NKK Switches can provide custom legends for caps. Contact factory for more information. www.nkkswitches.com D79