Datasheet Operational Amplifier Series Automotive Low Noise Operational Amplifiers BA4560Yxxx-M ●General Description BA4560Yxxx-M integrates two independent Op-Amps on a single chip. This Op-Amp has some features of low noise and low distortion characteristics and can operate from ±4.0V to ±15V(split supply). BA4560Yxxx-M is manufactured for automotive requirements of car navigation system, car audio, etc. ●Key Specifications Wide operating supply voltage (split supply):±4.0V to ±15V Wide Temperature Range: -40°C to +105°C High Slew Rate: 1V/µs(Typ.) Total Harmonic Distortion : 0.003%(Typ.) Input Referred Noise Voltage : 8 nV/ Hz (Typ.) ●Features AEC-Q100 Qualified High voltage gain low noise low distortion Wide operating supply voltage Internal ESD protection circuit Wide operating temperature Range ●Packages SOP8 SSOP-B8 MSOP8 W(Typ.) xD(Typ.) xH(Max.) 5.00mm x 6.20mm x 1.71mm 3.00mm x 6.40mm x 1.35mm 2.90mm x 4.00mm x 0.90mm ●Application Car Navigation System Car Audio ●Simplified schematic VCC VCC -IN －IN VOUT OUT +IN ＋IN VEE VEE Figure 1. Simplified schematic (one channel only) ○Product structure：Silicon monolithic integrated circuit ○This product is not designed protection against radioactive rays. www.rohm.com ©2013 ROHM Co., Ltd. All rights reserved. TSZ22111･14･001 1/17 TSZ02201-0RAR1G200640-1-2 1.Mar.2013 Rev.001 Datasheet BA4560Yxxx-M ●Pin Configuration BA4560YF-M : SOP8 BA4560YFV-M : SSOP-B8 BA4560YFVM-M : MSOP8 OUT1 1 -IN1 2 +IN1 3 VEE 4 CH1 - + CH2 + - Pin No. Symbol 1 OUT1 8 VCC 2 -IN1 7 OUT2 3 +IN1 6 -IN2 5 +IN2 4 VEE 5 +IN2 6 -IN2 7 OUT2 8 VCC Package SOP8 SSOP-B8 MSOP8 BA4560YF-M BA4560YFV-M BA4560YFVM-M ●Ordering Information B A 4 5 6 0 Y x x x - Packaging and forming specification M: Automotive（car navigation system, car audio, etc.） E2: Embossed tape and reel (SOP8/SSOP-B8) TR: Embossed tape and reel (MSOP8) Package F : SOP8 FV : SSOP-B8 FVM : MSOP8 Parts Number. BA4560Yxxx Mxx ●Line-up Topr -40°C to +105°C Supply voltage ±4.0V to ±15V www.rohm.com ©2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 Number of channels Dual Package Orderable Parts Number SOP8 Reel of 2500 BA4560YF-ME2 SSOP-B8 Reel of 2500 BA4560YFV-ME2 MSOP8 Reel of 3000 BA4560YFVM-MTR 2/17 TSZ02201-0RAR1G200640-1-2 1.Mar.2013 Rev.001 Datasheet BA4560Yxxx-M ●Absolute Maximum Ratings(Ta=25℃) Parameter Symbol Supply Voltage VCC-VEE Ratings Unit +36 V SOP8 775*1*4 SSOP-B8 625*2*4 MSOP8 600*3*4 Vid +36 V Input Common-mode Voltage Range Vicm V Operating Supply Voltage Vopr Operating Temperature Range Topr (VEE-0.3) to (VEE+36) +8.0 to +30 (±4.0 to ±15) -40 to +105 ℃ Tstg -55 to +150 ℃ Tjmax +150 ℃ Power Dissipation Differential Input Voltage *5 Storage Temperature Range Maximum Junction Temperature Pd mW V Note: Absolute maximum rating item indicates the condition which must not be exceeded. Application if voltage in excess of absolute maximum rating or use out of absolute maximum rated temperature environment may cause deterioration of characteristics. *1 To use at temperature above Ta＝25℃ reduce 6.2mW/℃. *2 To use at temperature above Ta＝25℃ reduce 5.0mW/℃. *3 To use at temperature above Ta＝25℃ reduce 4.8mW/℃. *4 Mounted on a FR4 glass epoxy PCB(70mm×70mm×1.6mm). *5 The voltage difference between inverting input and non-inverting input is the differential input voltage. Then input terminal voltage is set to more than VEE. www.rohm.com ©2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 3/17 TSZ02201-0RAR1G200640-1-2 1.Mar.2013 Rev.001 Datasheet BA4560Yxxx-M ●Electrical Characteristics ○BA4560Yxxx-M (Unless otherwise specified VCC=+15V, VEE=-15V, Full range -40℃ to +105℃) Limits Temperature Parameter Unit Condition Symbol Range Min. Typ. Max. Input Offset Voltage *6 Vio Input Offset Current *6 Iio Input Bias Current *7 Ib Supply Current ICC Maximum Output Voltage VOM Large Signal Voltage Gain Input Common-mode Voltage Range Av Vicm 25℃ - 0.5 6 Full range - - 7 25℃ - 5 200 Full range - - 200 25℃ - 50 500 Full range - - 800 25℃ - 3 7 Full range - - 7.5 25℃ ±12 ±14 - Full range ±10 ±11.5 - 25℃ 86 100 - Full range 83 - - 25℃ ±12 ±14 - Full range ±12 - - mV OUT=0V nA OUT=0V nA OUT=0V mA RL=∞, All Op-Amps VIN+=0V RL≧2kΩ V Io=25mA dB RL≧2kΩ, VO=±10V Vicm=0V V OUT=±12V Common-mode Rejection Ratio CMRR 25℃ 70 90 - dB OUT=±12V Power Supply Rejection Ratio PSRR 25℃ 76.5 90 - dB Ri≦10kΩ SR 25℃ - 4 - V/μs fT 25℃ - 4 - MHz RL=2kΩ THD+N 25℃ - 0.003 - % - 8 - nV/ Hz - 1.0 - μVrms DIN-AUDIO - 105 - Slew Rate Unity Gain Frequency Total Harmonic Distortion +Noise Input Referred Noise Voltage Channel Separation *6 *7 Vn CS Av=0dB, RL=10kΩ CL=100pF Av=20dB, RL=10kΩ VIN=0.05Vrms, f=1kHz RS=100Ω, Vi=0V, f=1kHz 25℃ 25℃ dB R1=100Ω, f=1kHz Absolute value Current direction: Since first input stage is composed with PNP transistor, input bias current flows out of IC. www.rohm.com ©2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 4/17 TSZ02201-0RAR1G200640-1-2 1.Mar.2013 Rev.001 Datasheet BA4560Yxxx-M Description of electrical characteristics Described here are the terms of electric characteristics used in this datasheet. Items and symbols used are also shown. Note that item name and symbol and their meaning may differ from those on another manufacture’s document or general document. 1. Absolute maximum ratings Absolute maximum rating item indicates the condition which must not be exceeded. Application of voltage in excess of absolute maximum rating or use out of absolute maximum rated temperature environment may cause deterioration of characteristics. 1.1 Power supply voltage (VCC-VEE) Indicates the maximum voltage that can be applied between the positive power supply terminal and negative power supply terminal without deterioration or destruction of characteristics of internal circuit. 1.2 Differential input voltage (Vid) Indicates the maximum voltage that can be applied between non-inverting terminal and inverting terminal without deterioration and destruction of characteristics of IC. 1.3 Input common-mode voltage range (Vicm) Indicates the maximum voltage that can be applied to non-inverting terminal and inverting terminal without deterioration or destruction of characteristics. Input common-mode voltage range of the maximum ratings not assure normal operation of IC. When normal operation of IC is desired, the input common-mode voltage of characteristics item must be followed. 1.4 Power dissipation (Pd) Indicates the power that can be consumed by specified mounted board at the ambient temperature 25℃(normal temperature). As for package product, Pd is determined by the temperature that can be permitted by IC chip in the package (maximum junction temperature)and thermal resistance of the package. 2. Electrical characteristics item 2.1 Input offset voltage (Vio) Indicates the voltage difference between non-inverting terminal and inverting terminal. It can be translated into the input voltage difference required for setting the output voltage at 0V. 2.2 Input offset current (Iio) Indicates the difference of input bias current between non-inverting terminal and inverting terminal. 2.3 Input bias current (Ib) Indicates the current that flows into or out of the input terminal. It is defined by the average of input bias current at non-inverting terminal and input bias current at inverting terminal. 2.4 Circuit current (ICC) Indicates the IC current that flows under specified conditions and no-load steady status. 2.5 Output saturation voltage (VOM) Signifies the voltage range that can be output under specific output conditions. 2.6 Large signal voltage gain (Av) Indicates the amplifying rate (gain) of output voltage against the voltage difference between non-inverting terminal and Inverting terminal. It is normally the amplifying rate (gain) with reference to DC voltage. Av = (Output voltage) / (Differential Input voltage) 2.7 Input common-mode voltage range (Vicm) Indicates the input voltage range where IC operates normally. 2.8 Common-mode rejection ratio (CMRR) Indicates the ratio of fluctuation of input offset voltage when in-phase input voltage is changed. It is normally the fluctuation of DC. CMRR = (Change of Input common-mode voltage)/(Input offset fluctuation) 2.9 Power supply rejection ratio (PSRR) Indicates the ratio of fluctuation of input offset voltage when supply voltage is changed. It is normally the fluctuation of DC. PSRR = (Change of power supply voltage) / (Input offset fluctuation) 2.10 Slew Rate (SR) SR is a parameter that shows movement speed of operational amplifier. It indicates rate of variable output voltage as unit time. 2.11 Unity gain frequency (fT) Indicates a frequency where the voltage gain of operational amplifier is 1. 2.12 Total harmonic distortion + Noise (THD+N) Indicates the fluctuation of input offset voltage or that of output voltage with reference to the change of output voltage of driven channel. 2.13 Input referred noise voltage (Vn) Indicates a noise voltage generated inside the operational amplifier equivalent by ideal voltage source connected in series with input terminal. 2.14 Channel separation (CS) Indicates the fluctuation of input offset voltage or that of output voltage with reference to the change of output voltage of driven channel. www.rohm.com ©2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 5/17 TSZ02201-0RAR1G200640-1-2 1.Mar.2013 Rev.001 Datasheet BA4560Yxxx-M ●Typical Performance Curves ○ BA4560Yxxx-M 1000 POWER DISSIPATION [mW] . . 5.0 -40℃ BA4560YF-M SUPPLY CURRENT [mA] 800 BA4560YFV-M 600 BA4560YFVM-M 400 200 0 25℃ 4.0 3.0 2.0 105℃ 1.0 0.0 0 25 50 75 100 125 0 AMBIENT TEMPERTURE [℃] . MAXIMUM OUTPUT VOLTAGE SWING [VP-P] 5.0 ±15V SUPPLY CURRENT [mA] 4.0 3.0 ±4 V ±7.5 V 1.0 0.0 -50 -25 0 25 50 75 100 AMBIENT TEMPERATURE [℃] 10 15 20 25 SUPPLY VOLTAGE [V] 30 35 Figure 3. Supply Current - Supply Voltage Figure 2. Derating Curve 2.0 5 125 30 25 20 15 10 5 0 0.1 1 LOAD RESISTANCE [kΩ] 10 Figure 5. Maximum Output Voltage Swing - Load Resistance (VCC/VEE=+15V/-15V, Ta=25℃) Figure 4. Supply Current - Ambient Temperature (*) The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com ©2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 6/17 TSZ02201-0RAR1G200640-1-2 1.Mar.2013 Rev.001 Datasheet BA4560Yxxx-M ○ BA4560Yxxx-M 20 20 15 15 10 10 OUTPUT VOLTAGE [V] OUTPUT VOLTAGE [V] VOH VOH 5 0 -5 VOL -10 5 0 -5 -10 VOL -15 -15 -20 0.1 -20 1 LOAD RESISTANCE [kΩ] 10 ±4 20 15 15 10 OUTPUT VOLTAGE [V] OUTPUT VOLTAGE [V] 20 VOH 5 0 VOL -10 VOH 5 0 -5 -20 -50 -20 25 50 75 100 VOL -10 -15 0 ±16 10 -15 -25 ±8 ±10 ±12 ±14 SUPPLY VOLTAGE [V] Figure 7. Maximum Output Voltage - Supply Voltage (RL=2kΩ, Ta=25℃) Figure 6. Maximum Output Voltage - Load Resistance (VCC/VEE=+15V/-15V, Ta=25℃) -5 ±6 0 125 AMBIENT TEMPERATURE [℃] 5 10 15 20 25 OUTPUT CURRENT [mA] Figure 9. Maximum Output Voltage - Output Current (VCC/VEE=+15V/-15V, Ta=25℃) Figure 8. Maximum Output Voltage - Ambient Temperature (VCC/VEE=+15V/-15V, RL=2kΩ) (*) The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com ©2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 7/17 TSZ02201-0RAR1G200640-1-2 1.Mar.2013 Rev.001 Datasheet BA4560Yxxx-M ○ BA4560Yxxx-M 6 INPUT OFFSETVOLTAGE VOLTAGE[mV] [mV] INPUT OFFSET INPUT OFFSET VOLTAGE [mV] 6 4 2 -40℃ 25℃ 0 105℃ -2 -4 4 ±4V 2 ±7.5V 0 -2 ±15V -4 -6 -6 ±2 ±4 ±6 ±8 ±10 ±12 ±14 -50 ±16 0 25 50 75 100 125 AMBIENT TEMPERATURE [℃] SUPPLY VOLTAGE [V] Figure 11. Input Offset Voltage - Ambient Temperature (Vicm=0V, OUT=0V) Figure 10. Input Offset Voltage - Supply Voltage (Vicm=0V, OUT=0V) 200 . . 200 180 180 INPUT BIAS CURRENT [nA] INPUT BIAS CURRENT [nA] -25 160 140 120 25℃ 100 -40℃ 80 60 40 105℃ 160 140 120 ±4V ±7.5V 100 80 60 40 ±15V 20 20 0 0 ±2 ±4 ±6 ±8 ±10 ±12 ±14 ±2 ±16 SUPPLY VOLTAGE [V] ±4 ±6 ±8 ±10 ±12 ±14 SUPPLY VOLTAGE [V] ±16 Figure 13. Input Bias Current - Ambient Temperature (Vicm=0V, OUT=0V) Figure 12. Input Bias Current - Supply Voltage (Vicm=0V, OUT=0V) (*) The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com ©2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 8/17 TSZ02201-0RAR1G200640-1-2 1.Mar.2013 Rev.001 Datasheet BA4560Yxxx-M . ○ BA4560Yxxx-M 60 INPUT OFFSET CURRENT [nA] INPUT OFFSET CURRENT [nA] 60 40 -40℃ 105℃ 20 0 -20 25℃ -40 40 ±4V 20 ±15V 0 ±7.5V -20 -40 -60 -60 ±0 ±2 -50 ±4 ±6 ±8 ±10 ±12 ±14 ±16 SUPPLY VO LTAG E [V] COMMON MODE REJECTION RATIO [dB] INPUT OFFSET VOLTAGE[mV] 5 4 3 2 105℃ 1 0 -1 -2 25℃ -3 -4 -5 -4 -3 -2 -1 0 1 2 3 125 Figure 15. Input Offset Current - Ambient Temperature (Vicm=0V, OUT=0V) Figure 14. Input Offset Current - Supply Voltage (Vicm=0V, OUT=0V) -40℃ -25 0 25 50 75 100 AMBIENT TEMPERATURE [°C] 4 150 125 100 75 50 25 0 -50 COMMON MODE INPUT VOLTAGE[V] -25 0 25 50 75 100 AMBIENT TEMPERATURE [°C] 125 Figure 17. Common Mode Rejection Ratio - Ambient Temperature (VCC/VEE=+15V/-15V, Vicm=-12V ~ +12V) Figure 16. Input Offset Voltage - Common Mode Input Voltage (VCC=4V, VEE=-4V, OUT=0V) (*) The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com ©2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 9/17 TSZ02201-0RAR1G200640-1-2 1.Mar.2013 Rev.001 Datasheet BA4560Yxxx-M 5.0 . 150 125 4.0 SLEW RATE [V/µs] POWER SUPPLY REJECTION RATIO [dB] . ○ BA4560Yxxx-M 100 75 50 3.0 2.0 1.0 25 0 0.0 -50 -25 0 25 50 75 100 AMBIENT TEMPERATURE [℃] 125 ±2 ±6 ±8 ±10 ±12 SUPPLY VOLTAGE [V] ±14 ±16 Figure 19. Slew Rate - Supply Voltage (CL=100pF, RL=2kΩ, Ta=25℃) Figure 18. Power Supply Rejection Ratio - Ambient Temperature (VCC/VEE=+4V/-4V ~ +15V/-15V) 1 TOTAL HARMONIC DISTORTION [%] 80 INPUT REFERRED NOISE VOLTAGE [nV/√Hz] . ±4 60 40 20 10 100 1000 0.01 1kHz 0.001 20Hz 0.0001 0.1 0 1 20kHz 0.1 10000 FREQUENCY [Hz] 1 OUTPUT VOLTAGE [Vrms] 10 Figure 21. Total Harmonic Distortion - Output Voltage (VCC/VEE=+15V/-15V, Av=20dB, RL=2kΩ, 80kHz-LPF, Ta=25℃) Figure 20. Equivalent Input Noise Voltage - Frequency (VCC/VEE=+15V/-15V, RS=100Ω, Ta=25℃) (*) The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com ©2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 10/17 TSZ02201-0RAR1G200640-1-2 1.Mar.2013 Rev.001 Datasheet BA4560Yxxx-M 30 60 25 50 0 -30 20 15 10 5 10 10 3 1000 4 10000 5 100000 10 10 FREQUENCY [Hz] 10 -60 30 -90 GAIN 20 -120 10 -150 0 -180 1.E+02 1.E+04 1.E+06 1.E+07 102 1.E+03 103 104 1.E+05 105 106 107 0 2 100 40 PHASE [deg] PHASE VOLTAGE GAIN [dB] MAXIMUM OUTPUT VOLTAGE SWING [VP-P] ○ BA4560Yxxx-M 6 1000000 10 FREQUENCY [Hz] Figure 23. Voltage Gain, Phase - Frequency (VCC/VEE=+15V/-15V, Av=40dB, RL=2kΩ, Ta=25℃) Figure 22. Maximum Output Voltage Swing – Frequency (VCC/VEE=+15V/-15V, RL=2kΩ, Ta=25℃) (*) The above data is measurement value of typical sample, it is not guaranteed. www.rohm.com ©2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 11/17 TSZ02201-0RAR1G200640-1-2 1.Mar.2013 Rev.001 Datasheet BA4560Yxxx-M ●Power Dissipation Power dissipation (total loss) indicates the power that the IC can consume at Ta=25°C (normal temperature). As the IC consumes power, it heats up, causing its temperature to be higher than the ambient temperature. The allowable temperature that the IC can accept is limited. This depends on the circuit configuration, manufacturing process, and consumable power. Power dissipation is determined by the allowable temperature within the IC (maximum junction temperature) and the thermal resistance of the package used (heat dissipation capability). Maximum junction temperature is typically equal to the maximum storage temperature. The heat generated through the consumption of power by the IC radiates from the mold resin or lead frame of the package. Thermal resistance, represented by the symbol θja°C/W, indicates this heat dissipation capability. Similarly, the temperature of an IC inside its package can be estimated by thermal resistance. Figure 24. (a) shows the model of the thermal resistance of the package. The equation below shows how to compute for the Thermal resistance (θja), given the ambient temperature (Ta), maximum junction temperature (Tjmax), and power dissipation (Pd). θja = (Tjmax - Ta) / Pd ℃/W ・・・・・ (Ⅰ) The Derating curve in Figure 24. (b) indicates the power that the IC can consume with reference to ambient temperature. Power consumption of the IC begins to attenuate at certain temperatures. This gradient is determined by Thermal resistance (θja), which depends on the chip size, power consumption, package, ambient temperature, package condition, wind velocity, etc. This may also vary even when the same of package is used. Thermal reduction curve indicates a reference value measured at a specified condition. Figure 25. (c) shows an example of the derating curve for BA4560Yxxx-M. LSIの 消 費 力 [W] Power dissipation of電LSI Pd (max) θja = ( Tjmax - Ta) / Pd Ambient temperature ℃ /W θja2 < θja1 P2 Ta [℃] θ' ja2 P1 θ ja2 Tj ' (max) Tj (max) θ' ja1 Chip surface temperature Tj [℃] 0 25 50 θ ja1 75 100 125 150 周 囲 温 度 Ta [℃ ] Ambient temperature Power dissipation Pd[W] (b) Derating curve (a) Thermal resistance Figure 24. Thermal resistance and derating POWER DISSIPATION [mW] . 1000 BA4560YF-M(8) 800 BA4560YFV-M(9) 600 BA4560YFVM-M(10) 400 200 0 0 25 50 75 100 125 AMBIENT TEMPERTURE [℃] . (c) BA4560Yxxx-M (8) (9) (10) Unit 6.2 5.0 4.8 mW/℃ When using the unit above Ta=25℃, subtract the value above per Celsius degree . Mounted on a FR4 glass epoxy board 70mm×70mm×1.6mm(cooper foil area below 3%) Figure 25. Derating curve www.rohm.com ©2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 12/17 TSZ02201-0RAR1G200640-1-2 1.Mar.2013 Rev.001 Datasheet BA4560Yxxx-M ●Application Information NULL method condition for Test circuit1 VCC, VEE, EK, Vicm Unit: V Parameter VF S1 S2 S3 VCC VEE EK Vicm calculation Input Offset Voltage VF1 ON ON OFF 15 -15 0 0 1 Input Offset Current VF2 OFF OFF OFF 15 -15 0 0 2 VF3 OFF ON VF4 ON OFF OFF 15 -15 0 0 3 ON ON ON 15 -15 0 0 15 -15 0 0 ON ON OFF 3 -27 0 0 27 -3 0 0 ON ON OFF 4 -4 0 0 15 -15 0 0 Input Bias Current VF5 Large Signal Voltage Gain VF6 VF7 Common-mode Rejection Ratio (Input common-mode Voltage Range) VF8 Power Supply Rejection Ratio VF10 VF9 4 5 6 - Calculation 1. Input Offset Voltage (Vio) Vio VF1 [V] 1+ RF / RS 2. Input Offset Current (Iio) Iio VF2 - VF1 Ri × (1 + RF / RS) [A] 0.1µF 3. Input Bias Current (Ib) Ib VF4 - VF3 2 × Ri × (1 + RF / RS) RF=50kΩ SW1 VCC 15V EK 4. Large Signal Voltage Gain (Av) Av 20 × Log ΔEK × (1+ RF/RS) VF5 - VF6 0.1µF 500kΩ [A] RS=50Ω Vo Ri=10kΩ 500kΩ DUT [dB] 5. Common-mode Rejection Ration (CMRR) ΔVicm × (1+ RF/RS) [dB] CMRR 20 × Log VF8 - VF7 NULL SW3 RS=50Ω 1000pF Ri=10kΩ RL VF Vicm SW2 50kΩ -15V VEE 6. Power supply rejection ratio (PSRR) PSRR 20 × Log Figure 26. Test circuit1 (one channel only) ΔVcc × (1+ RF/RS) [dB] VF10 - VF9 www.rohm.com ©2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 13/17 TSZ02201-0RAR1G200640-1-2 1.Mar.2013 Rev.001 Datasheet BA4560Yxxx-M Switch Condition for Test Circuit 2 SW 1 SW No. SW 2 SW 3 SW 4 SW 5 SW 6 SW 7 SW 8 SW 9 SW 10 SW 11 SW 12 SW 13 SW 14 Supply Current OFF OFF OFF ON OFF ON OFF OFF OFF OFF OFF OFF OFF OFF Maximum Output Voltage (high) OFF OFF ON OFF OFF ON OFF OFF ON OFF OFF OFF ON OFF Maximum Output Voltage (Low) OFF OFF ON OFF OFF ON OFF OFF OFF OFF OFF OFF ON OFF Slew Rate OFF OFF OFF ON OFF OFF OFF ON ON OFF OFF OFF OFF Unity Gain Frequency OFF ON OFF OFF ON ON OFF OFF ON ON ON OFF OFF OFF Total Harmonic Distortion ON OFF OFF OFF ON OFF ON OFF ON ON ON OFF OFF OFF Input Referred Noise Voltage ON OFF OFF OFF ON ON OFF OFF OFF OFF ON OFF OFF OFF ON Input voltage VH VL Input wave Output voltage t SR＝ΔV/Δt 90% VH ΔV C 10% VL Δt Output wave Figure 28. Slew Rate Input Waveform Figure 27. Test Circuit 2 (each Op-Amp) VCC VCC R1//R2 R1//R2 OTHER CH VEE R1 VEE R2 V VIN 40dB amplifier t OUT1 =0.5Vrms R1 R2 V OUT2 40dB amplifier CS 20 log 100 OUT1 OUT2 (R1=1kΩ, R2=100kΩ) Figure 29. Test Circuit 3(Channel Separation) www.rohm.com ©2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 14/17 TSZ02201-0RAR1G200640-1-2 1.Mar.2013 Rev.001 Datasheet BA4560Yxxx-M ●Operational Notes 1) Processing of unused circuit It is recommended to apply connection (see the Figure 30.) and set the non inverting input terminal at the potential within input common-mode voltage range (Vicm), for any unused circuit. 2) Input voltage Applying (VEE - 0.3) to (VEE + 36)V (BA4558R) to the input terminal is possible without causing deterioration of the electrical characteristics or destruction, irrespective of the supply voltage. However, this does not ensure normal circuit operation. Please note that the circuit operates normally only when the input voltage is within the common mode input voltage range of the electric characteristics. 3) Maximum output voltage Because the output voltage range becomes narrow as the output current Increases, design the application with margin by considering changes in electrical characteristics and temperature characteristics. 4) Short-circuit of output terminal When output terminal and VCC or VEE terminal are shorted, excessive Output current may flow under some conditions, and heating may destroy IC. It is necessary to connect a resistor as shown in Figure 31., thereby protecting against load shorting. 5) Power supply (split supply / single supply) in used Op-amp operates when specified voltage is applied between VCC and VEE. Therefore, the single supply Op-Amp can be used for double supply Op-Amp as well. VCC + Connect to Vicm Vicm VEE Figure 30. The example of application circuit for unused op-amp VCC + protection resistor VEE Figure 31. The example of output short protection 6) Power dissipation (Pd) Use a thermal design that allows for a sufficient margin in light of the power dissipation (Pd) in actual operating conditions. 7) Short-circuit between pins and wrong mounting Pay attention to the assembly direction of the ICs. Wrong mounting direction or shorts between terminals, GND, or other components on the circuits, can damage the IC. 8) Use in strong electromagnetic field Using the ICs in strong electromagnetic field can cause operation malfunction. 9) Radiation This IC is not designed to be radiation-resistant. 10) IC Handling When stress is applied to IC because of deflection or bend of board, the characteristics may fluctuate due to piezo resistance effects. 11) Inspection on set board During testing, turn on or off the power before mounting or dismounting the board from the test Jig. Do not power up the board without waiting for the output capacitors to discharge. The capacitors in the low output impedance terminal can stress the device. Pay attention to the electro static voltages during IC handling, transportation, and storage. 12) Output capacitor When VCC terminal is shorted to VEE (GND) potential and an electric charge has accumulated on the external capacitor, connected to output terminal, accumulated charge may be discharged VCC terminal via the parasitic element within the circuit or terminal protection element. The element in the circuit may be damaged (thermal destruction). When using this IC for an application circuit where there is oscillation, output capacitor load does not occur, as when using this IC as a voltage comparator. Set the capacitor connected to output terminal below 0.1μF in order to prevent damage to IC. www.rohm.com ©2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 15/17 TSZ02201-0RAR1G200640-1-2 1.Mar.2013 Rev.001 Datasheet BA4560Yxxx-M ●Physical Dimensions Tape and Reel Information SOP8 <Tape and Reel information> 7 6 5 6.2±0.3 4.4±0.2 0.3MIN 8 +6° 4° −4° 0.9±0.15 5.0±0.2 (MAX 5.35 include BURR) 1 2 3 Tape Embossed carrier tape Quantity 2500pcs Direction of feed E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand ) 4 0.595 1.5±0.1 +0.1 0.17 -0.05 S S 0.11 0.1 1.27 Direction of feed 1pin 0.42±0.1 Reel (Unit : mm) ∗ Order quantity needs to be multiple of the minimum quantity. SSOP-B8 <Tape and Reel information> 3.0±0.2 (MAX 3.35 include BURR) 8 7 6 5 Tape Embossed carrier tape Quantity 2500pcs E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand ) 0.3MIN 6.4 ± 0.3 4.4 ± 0.2 Direction of feed 2 3 4 0.1 1.15±0.1 1 0.15±0.1 S (0.52) 0.65 0.1 S +0.06 0.22 −0.04 0.08 Direction of feed 1pin M Reel (Unit : mm) ∗ Order quantity needs to be multiple of the minimum quantity. MSOP8 <Tape and Reel information> 2.8±0.1 4.0±0.2 8 7 6 5 0.6±0.2 +6° 4° −4° 0.29±0.15 2.9±0.1 (MAX 3.25 include BURR) Tape Embossed carrier tape Quantity 3000pcs Direction of feed TR The direction is the 1pin of product is at the upper right when you hold ( reel on the left hand and you pull out the tape on the right hand ) 1 2 3 4 1PIN MARK 1pin +0.05 0.145 −0.03 0.475 0.75±0.05 0.08±0.05 0.9MAX S +0.05 0.22 −0.04 0.08 S Direction of feed 0.65 (Unit : mm) www.rohm.com ©2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 Reel 16/17 ∗ Order quantity needs to be multiple of the minimum quantity. TSZ02201-0RAR1G200640-1-2 1.Mar.2013 Rev.001 Datasheet BA4560Yxxx-M ●Marking Diagram SOP8(TOP VIEW) SSOP-B8(TOP VIEW) Part Number Marking Part Number Marking LOT Number LOT Number 1PIN MARK 1PIN MARK MSOP8(TOP VIEW) Part Number Marking Product Name LOT Number BA4560Y Package Type Marking F-M SOP8 60YM FV-M SSOP-B8 MSOP8 60YM FVM-M 60YM 1PIN MARK ●Land pattern data SOP8, SSOP-B8, MSOP8 b2 e MIE ℓ2 All dimensions in mm Land length Land width ≧ℓ 2 b2 Land pitch e Land space MIE SOP8 1.27 4.60 1.10 0.76 SSOP-B8 0.65 4.60 1.20 0.35 MSOP8 0.65 2.62 0.99 0.35 PKG ●Revision History Date 1.Mar.2013 Revision 001 Changes New Release www.rohm.com ©2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 17/17 TSZ02201-0RAR1G200640-1-2 1.Mar.2013 Rev.001 Datasheet Notice Precaution on using ROHM Products 1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice - SS © 2014 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with ROHM representative in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable for infringement of any intellectual property rights or other damages arising from use of such information or data.: 2. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the information contained in this document. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice - SS © 2014 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s representative. 3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. Notice – WE © 2014 ROHM Co., Ltd. All rights reserved. Rev.001