Online data sheet M20Z-02550A122, PSR01-1501 M2000 Standard A/P MULTIPLE LIGHT BEAM SAFETY DEVICES M20Z-02550A122, PSR01-1501 | M2000 Standard A/P MULTIPLE LIGHT BEAM SAFETY DEVICES A B C D E F Ordering information System part Type Part no. Sender/receiver in one housing M20Z-02550A122 1018361 Deflector unit PSR01-1501 1016677 1.) Concerns installation as a replacement part for previous type 2 device in machine: Regarding Machinery Directive 2006/42/EC, Article 1, Paragraph (2a) this type 2 device may only be used as a replacement part for identical PL d / SIL2 devices within the EU if the machine was put into circulation before 2015-05-10. Keep this note with your machine documentation. If the machine is sold on, this note and the information it contains must be passed on to every subsequent buyer. 2.) Concerns installation on new machines: Due to the amendment to the EN/IEC 61496-1 standard, this type 2 device may only be installed on new machines up to PL c / SIL1 as of 2015-05-10. Other models and accessories www.sick.com/M2000_Standard_A_P Detailed technical data Features H I J K L M N O P Q R S T Scanning range 0 m ... 6 m Number of beams 2 Beam separation 500 mm Response time 7 ms Synchronization Optical synchronisation Safety-related parameters Type Type 2 (IEC 61496) Safety integrity level SIL1 (IEC 61508) SILCL1 (EN 62061) Category Category 2 (EN ISO 13849) Test rate (internal test) 13 /s (EN ISO 13849) 1) Maximum demand rate ≤ 8 min⁻¹ (EN ISO 13849) 2) Performance level PL c (EN ISO 13849) PFHD (mean probability of a dangerous failure per hour) 6.6 x 10-9 (EN ISO 13849) TM (mission time) 20 years (EN ISO 13849) Safe state in the event of a fault At least one OSSD is in the OFF state. 1) 2) Internal test. The test rate may not be exceeded if an external test is performed. Between two requirements on a safety-related response of the device, at least 100 internal or external tests must be carried out. Functions Functions External device monitoring (EDM) ✔ Beam coding ✔ 2 OPTO-ELECTRONIC PROTECTIVE DEVICES | SICK Delivery status Code 1 Online data sheet | 2017-06-14 08:06:28 Subject to change without notice M20Z-02550A122, PSR01-1501 | M2000 Standard A/P MULTIPLE LIGHT BEAM SAFETY DEVICES Interfaces System connection Connection type Male connector M12, 8-pin Permitted cable length ≤ 15 m 1) Permitted cross-section ≥ 0.25 mm² Configuration method Hard wired Display elements LEDs 7-segment display Fieldbus, industrial network Integration via Flexi Soft safety controller CANopen, DeviceNet™, EtherCAT®, EtherNet/IP™, Modbus TCP, PROFIBUS DP, PROFINET 2) 1) 2) Depending on load, power supply and wire cross-section. The technical specifications must be observed. For additional information on Flexi Soft -> www.sick.com/Flexi_Soft. Electrical data Protection class III (EN 50178) Supply voltage VS 24 V DC (19.2 V DC ... 28.8 V DC) 1) Power consumption ≤ 7.5 W (DC) Safety outputs (OSSD) Type of output 2 PNP semiconductors, short-circuit protected, cross-circuit monitored 2) Switching voltage HIGH 24 V DC (VS – 2.25 V DC ... VS) Switching voltage LOW ≤ 1 V DC Switching current ≤ 500 mA 1) The external voltage supply must be capable of buffering brief mains voltage failures of 20 ms as specified in EN 60204-1. Suitable power supplies are available as accessories from SICK. 2) Applies to the voltage range between –30 V and +30 V. Mechanical data Housing cross-section 48 mm x 40 mm Ambient data Enclosure rating IP65 (EN 60529) Ambient operating temperature 0 °C ... +55 °C Storage temperature –25 °C ... +70 °C Air humidity 15 % ... 95 %, Non-condensing Vibration resistance 5 g, 10 Hz ... 55 Hz (IEC 60068-2-6) Shock resistance 10 g, 16 ms (IEC 60068-2-29) Other information Wave length 2017-06-14 08:06:28 | Online data sheet Subject to change without notice 950 nm OPTO-ELECTRONIC PROTECTIVE DEVICES | SICK 3 M20Z-02550A122, PSR01-1501 | M2000 Standard A/P MULTIPLE LIGHT BEAM SAFETY DEVICES Dimensional drawing (Dimensions in mm (inch)) 8 1.7 (0.31) (0.07) 14 1 (0.55) Ø 8.4 3.5 1 2.2 (0.47) 3 4 (0.33) 10.5 (0.09) 11.9 (0.14) 6 (0.24) (0.04) 2 40 (0.41) (1.57) 42.9 (1.69) S 48 75 (2.95) 68 (2.68) 48 (1.89) 22.4 S1 L1 L2 L3 L4 L5 (0.88) 44.4 25.6 (1.01) 5 (1.75) (1.89) L6 A B C D E F R 76.3 (3.00) 42.3 (1.87) 47.6 (1.67) 42.6 (0.89) (1.68) 22.5 H I J K L M N O P Q R S T 6 Number of beams Beam separation L1 L2 L3 L4 L5 L6 2 500 (19.69) 653 (25.71) 611 (24.06) 720 (28.35) 741 (29.17) 678 (26.69) 700 (27.56) Recommended accessories Other models and accessories www.sick.com/M2000_Standard_A_P Brief description Type Part no. BEF-3WNGBAST4 7021352 BEF-0AAAA0004S01 2021569 Mounting brackets and plates 4 pieces, Mounting kit 1, mounting bracket, rigid, L-shaped, including fixing screws and washers Terminal and alignment brackets 4 pieces, Mounting kit 9, rotatable, 2-piece swivel mount for M2000 A/P and 2-piece side bracket for deflector mirror PSR01-1501 4 OPTO-ELECTRONIC PROTECTIVE DEVICES | SICK Online data sheet | 2017-06-14 08:06:28 Subject to change without notice M20Z-02550A122, PSR01-1501 | M2000 Standard A/P MULTIPLE LIGHT BEAM SAFETY DEVICES Brief description Type Part no. 4 pieces, Mounting kit 6, side bracket, rotatable, Zinc diecast BEF-1SHABAZN4 2019506 4 pieces, Omega bracket, rotatable, fixable with only one screw, for mounting on the swivel mount BEF-2SMMEAAL4 2044847 4 pieces, Mounting kit 2, rotatable, swivel mount, Polyamide PA6 BEF-2SMMEAKU4 2019659 AR60 1015741 AR60 adapter, 48x40 4032461 AR60 adapter, 48x40, PU3H 4056731 Alignment aids Laser alignment aid for various sensors, laser class 2 (IEC 60825). Do not look into the beam! Adapter AR60 for housing cross-section 48 mm x 40 mm Adapter AR60 for housing cross-section 48 mm x 40 mm in PU3H device column 2017-06-14 08:06:28 | Online data sheet Subject to change without notice OPTO-ELECTRONIC PROTECTIVE DEVICES | SICK 5 Online data sheet SICK at a glance SICK is one of the leading manufacturers of intelligent sensors and sensor solutions for industrial applications. A unique range of products and services creates the perfect basis for controlling processes securely and efficiently, protecting individuals from accidents and preventing damage to the environment. We have extensive experience in a wide range of industries and understand their processes and requirements. With intelligent sensors, we can deliver exactly what our customers need. In application centers in Europe, Asia and North America, system solutions are tested and optimized in accordance with customer specifications. All this makes us a reliable supplier and development partner. Comprehensive services complete our offering: SICK LifeTime Services provide support throughout the machine life cycle and ensure safety and productivity. For us, that is “Sensor Intelligence.” Worldwide presence: Contacts and other locations – www.sick.com SICK AG | Waldkirch | Germany | www.sick.com