7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER WIRE INSUL - SERVO LATCH PLATE 2150369 -5 B FINE CRIMP HEIGHT ADJUST SERVO LATCH PLATE - SERVO LATCH PLATE 11 2150369 -6 B NON-CRIMP HEIGHT ADJUST 2150369 -7 B FINE CRIMP HEIGHT ADJUST 2 SET UP GAUGE 2119599-2 A 4 CRIMP TOOLING KIT NONE - 4 - - - - - 2063961-1 - - - - - 2119950-1 - - 8- 2150369 -5 PNEUMATIC FEED - - 1901697-1 2161326-1 - 2063961-1 2119951-1 SMART APPLICATOR - - - - 2119792-2 - 8- 2150369 -4 - - - 2119641-1 - - 2168400-7 n TERMINAL APPLICATION SPECIFICATION 114-18022 - 2063440-2 - - - - TERMINALS APPLIED - 10 962835-2 C1__DWG_PN_1_1 2.40-3.70 mm [.094-.146 IN] - TE TERMINAL C1__DWG_PN_1_0 INSULATION DIAMETER RANGE - C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_2_1 962835-3 C1__DWG_PN_3_0 C1__DWG_PN_3_1 TE TERMINAL C1__DWG_PN_4_0 8-962835-3 6 C1__DWG_PN_4_1 12 WIRE SIZE 2.50mm2 2.00mm2 1.50mm2 B 1 2 CRIMP HEIGHT REFERENCE SETTING CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 2.18+/-0.05 [.086+/-.002] 2.05+/-0.05 [.081+/-.002] 1.92+/-0.05 [.076+/-.002] W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 9 4.8 W1__FA_SETTING_1 6.4 W1__FA_SETTING_2 7.8 W1__FA_SETTING_3 *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. RECOMMENDED SPARE PARTS GREASE BEARING SURFACES LIGHTLY 6 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8SERVO FEED WITH "NON-CRIMP HEIGHT ADJUST": 8- 2150369 -4 2150369 -5 2150369 -6 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. 6 7 8 9 A 10 11 12 1 APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEMS 62. APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEMS 242. FOR -6 ONLY APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEMS 37. 1 1 1 GREASE THREADS, GROOVE AND O-RING ON ITEMS 35 & 252. MAGNET, ITEM 166 MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. 1 CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 1 CUT TO LENGTH AT ASSEMBLY. AMP 4805 REV 31MAR2000 - - 1 - - 1 - 1 1 - - - - 1 - - - - 1 - - - - 1 - 1 - 1 1 - 1 - 1 1 - - 1 - - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - - 2 2 - - - - 1 - - 1 1 - - REF REF - - - - 2 - 1 1 1 1 - REF REF REF REF - - - - 1 - - - - 1 - - REF REF - - 1 1 - 1 1 1 1 - 1 1 1 1 - 2 2 2 2 - 1 - - 1 - 2 2 2 2 - 2 2 2 2 - 1 - 1 1 - 3 - 3 3 - 1 1 1 1 - 3 3 3 3 - 2 2 2 2 - 2 2 2 2 - 2 2 2 2 - 2 2 2 2 - - - - 1 - - - - 1 - 1 1 1 1 - 1 - 1 1 - 1 1 1 1 - 1 - 1 1 - 1 - 1 1 - 1 1 1 1 - 1 1 1 1 - 1 - 1 1 - 7 7 7 7 - 2 2 2 2 - 2 2 2 2 - 1 1 1 1 - 2 2 2 2 - 1 1 1 1 - 1 1 1 1 - 2 2 2 2 - 1 1 1 1 - 2 2 2 2 - 4 4 4 4 - 1 1 1 1 - 1 1 1 1 - - - - - 1 1 1 1 1 1 1 1 1 - 1 1 1 1 - - - - - 1 1 1 1 - 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 2 1 1 1 1 1 1 1 1 2 1 2 2 1 3 1 3 2 2 2 2 1 1 1 1 1 1 1 1 1 1 7 2 2 1 2 1 1 2 1 2 4 1 1 1 1 1 1 1 1 1 1 1 1 -77 -7 -6 -5 -2 TERMINAL PITCH NOT COMPATIBLE WITH MECHANICAL FEED. WHEN ASSEMBLING -6 NON-CRIMP HEIGHT ADJUST APPLICATOR USE SHIM PACK 2119957-2 TO ALIGN APPLICATOR'S MAXIMUM WIRE CRIMP HEIGHT AT NORMAL TERMINATOR SHUT HEIGHT LTR THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 DESCRIPTION DATE DWN APVD A RELEASED 05NOV2013 BH GB B ECR-16-001409 29JAN2016 JH CT - TE CRIMP SPECIFICATION 4.80-5.60 mm [.189-.220 IN] P - F F WIRE STRIP LENGTH 66 (QUANTITY 2) FASTIN-FASTON RECEPTACLE SERIE 9.5 TERMINAL NAME: A REVISIONS DIST - TYPE TE TERMINAL LOC 1 PART NUMBERS REQUIRED 6 4.57 mm [.180] 962835-1 CONVERT TO PNEUMATIC 3.05 mm [.120] TE TERMINAL FEED TYPE FINE CRIMP HEIGHT ADJUST APPLICATOR INSTRUCTIONS 408-10390 C DESCRIPTION B SIZE TERMINAL DATA: 3 APPLICATOR STYLE CONVERSION CHART 2150369 -2 APPLICATOR DATA 4 20 REVISION 7- 2150369 -7 CRIMP 5 ALL RIGHTS RESERVED. PART NUMBER D 6 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: PART NO DWN 27SEPT2013 CHK 27SEPT2013 APVD 27SEPT2013 K. STAKEM G. BAILEY T. ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 ITEM NO DESCRIPTION APPLICATION SPEC - 260 252 250 249 248 247 246 245 244 243 242 240 238 213 183 172 166 164 163 137 135 133 82 71 70 67 66 64 63 62 60 57 56 55 54 53 51 49 46 44 41 40 39 38 37 35 33 31 29 27 25 24 23 22 20 18 17 16 11 10 9 8 7 6 5 4 3 2 1 APPLICATOR SHIM PACK O-RING, .676 ID, .070 DIA. MAT. PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI FEED CAM, AIR FEED DETENT PIN SPRING, COMPRESSION RAM, AMP STYLE, END FEED, NON-ADJUST CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SHCS, LOW HEAD, RoHS, M5 X 10 AIR FEED MODULE TAG,IDENTIFICATION FEED FINGER ASSEMBLY,EF RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER PIN, RETAIN, GRVD, 3/16 X .854 MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM SPACER, CRIMPER DOCUMENTATION PACKAGE SCR, SET, FLT POINT M3 X 10.0 TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SKT HD CAP, RoHS, M4 X 16 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SCR, BHSC, RoHS (M4 X 8) SHCS, LOW HEAD, RoHS, M4 X 8 SCR, SKT HD CAP, RoHS, M4 X 20 NUT, HEX, REG, RoHS, M4 NUT, HEX, REG, RoHS, M3 NUT, LOCK, HEX, TORQUE (M4) PAWL, EF, AIR SCR, SKT HD CAP M4 X 6.0 APPLICATOR BASIC ASSEMBLY, EF RAM,AMP STYLE, END FEED SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION FA HEAD, ATLANTIC STYLE BOLT, ADJUSTMENT WASHER, FLAT, REG M4 SCR, SKT HD CAP, RoHS, M4 X 16 SCR, SKT HD CAP, RoHS, M4 X 10 STRIPPER (MACHINING) STUD, THREADED PLATE, STRIP GUIDE PLATE, STRIP HOLD DOWN SPRING, COMPRESSION DRAG GUIDE, LOWER STRIP SCR, BHSC, RoHS (M6 X 12) SPACER PLATE, REAR SHEAR PLATE, FRONT SHEAR ANVIL, COMBINATION, .120 BLADE, SLUG SPACER BLOCK, FL CRIMPER SPACER CRIMPER, INSULATION F PREMIUM SPACER, CRIMPER CRIMPER, WIRE .120 "F" PREMIUM PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH 2119957-2 8-21084-0 2119640-1 2079988-1 2119641-1 2119798-1 1-22279-3 2119759-1 2119082-9 2079764-1 2119083-1 2168400-7 2063440-2 2119740-2 1901697-1 21045-3 994969-1 994970-2 240638-1 3-23627-7 SEE NOTE 4 1633743-1 455888-4 2119956-2 2-18032-2 2119740-1 2168078-1 2168083-8 2119793-1 992763-5 2079383-4 2168400-4 2168083-9 5018030-2 5018030-1 986965-8 2119792-2 18023-9 2119655-5 2119369-1 2079383-7 2119645-1 2119957-1 2119644-2 2119085-1 2119092-1 1-18028-2 2168083-8 1-2168083-0 240639-1 1320906-1 1752371-6 240825-1 2-22281-3 1752373-4 1901259-6 1-2079383-1 240641-7 240833-7 1-690482-2 1333220-4 2217206-8 5-240641-7 238009-1 2119582-3 1-455888-4 456409-3 Ocean End Feed Applicator - DRAWING NO 2150369 SCALE 1:1 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV B D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC REVISIONS DIST A ALL RIGHTS RESERVED. 1 66 P LTR - 6 DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - 37 40 6 62 38 D 39 247 260 7 7 246 252 245 35 44 243 6 2 166 FEED TYPE 2 2 56 12 2 2 244 242 7 PNEUMATIC 16 5 8 63 238 249 82 1 1 2 250 A C 137 C 163 2 3 D 1 172 70 4 51 54 41 55 10 6 A 164 20 2 64 57 33 23 SERVO LATCH PLATE 67 213 B 18 66 B CAM POSITIONS 30mm STROKE 29 33 27 8 1 46 60 31 9 1 11 17 53 33 25 22 SERVO FEEDER NOT INCLUDED A 24 248 4 135 133 183 240 REF 49 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 40mm STROKE AIR FEED AMP 4805 REV 31MAR2000 DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 27SEPT2013 CHK 27SEPT2013 APVD 27SEPT2013 K. STAKEM G. BAILEY T. ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH DWN - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean End Feed Applicator - DRAWING NO 2150369 SCALE 1:1 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV B 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 6 5 4 3 2 20 SET UP GAUGE 2119599-2 ALL RIGHTS RESERVED. PART NUMBER REVISION DESCRIPTION FEED TYPE 2- 2150369 -2 B FINE CRIMP HEIGHT ADJUST PNEUMATIC 2- 2150369 -5 B FINE CRIMP HEIGHT ADJUST SERVO LATCH PLATE 2- 2150369 -7 B FINE CRIMP HEIGHT ADJUST NONE 7- 2150369 -7 A APPLICATOR STYLE CONVERSION CHART CRIMP TOOLING KIT - CONVERT TO - SERVO LATCH PLATE SMART APPLICATOR - 4 CRIMP - 2063961-1 - 2119653-2 - WIRE INSUL 8- 2150369 -4 - - 2119951-1 1901697-1 8- 2150369 -5 - 2063961-1 - 2119653-2 - - - - 2161326-1 2119950-1 - - - 2119792-2 - - - 2119641-2 - - 2168400-7 APPLICATOR INSTRUCTIONS 408-10390 TE TERMINAL TERMINAL DATA: - 2063440-2 - - - n 4.80-5.60 mm [.189-.220 IN] C TERMINAL APPLICATION SPECIFICATION 114-18022 - TERMINALS APPLIED TE TERMINAL 962835-1 WIRE SIZE 2.50mm2 2.00mm2 1.50mm2 B 962835-2 C1__DWG_PN_1_1 2.40-3.70 mm [.094-.146 IN] - - - 10 TE TERMINAL C1__DWG_PN_1_0 INSULATION DIAMETER RANGE - C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_2_1 962835-3 C1__DWG_PN_3_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 2.18+/-0.05 [.086+/-.002] 2.05+/-0.05 [.081+/-.002] 1.92+/-0.05 [.076+/-.002] 1 RECOMMENDED SPARE PARTS 2 GREASE BEARING SURFACES LIGHTLY TE TERMINAL W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 C1__DWG_PN_4_0 8-962835-3 CRIMP HEIGHT REFERENCE SETTING CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 C1__DWG_PN_3_0 4.8 6.4 7.8 C1__DWG_PN_4_1 6 9 11 W1__FA_SETTING_1 W1__FA_SETTING_2 W1__FA_SETTING_3 *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8- 2150369 -4 2150369 -5 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. 6 7 8 9 A 1 APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEMS 62. APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEMS 242. 1 1 GREASE THREADS, GROOVE AND O-RING ON ITEMS 139 & 153. 1 MAGNET, ITEM 166 MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 10 TERMINAL PITCH NOT COMPATIBLE WITH MECHANICAL FEED. 11 CUT TO LENGTH AT ASSEMBLY. 1 1 - 1 1 1 - - - 1 - - - 1 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - - 2 - - - 1 - - 1 - 4 4 4 - - REF - - - 2 - 1 1 1 - REF REF REF - - - 1 - 1 1 1 - - - 1 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - - - 1 - - REF - - 1 - 1 1 1 - 1 1 1 - 2 2 2 - 1 - 1 - 2 2 2 - 2 2 2 - 1 1 1 - 3 3 3 - 3 3 3 - 2 2 2 - 2 2 2 - 2 2 2 - 2 2 2 - - - 1 - - - 1 - 1 1 1 - 1 1 1 - 1 1 1 - 1 1 1 - 7 7 7 - 2 2 2 - 2 2 2 - 1 1 1 - 2 2 2 - 1 1 1 - 1 1 1 - 2 2 2 - 1 1 1 - 2 2 2 - 1 1 1 - 1 1 1 - - - - 1 1 1 1 1 1 1 - 1 1 1 - - - - 1 1 1 - 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 4 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 2 1 3 3 2 2 2 2 1 2 1 1 1 1 7 2 2 1 2 1 1 2 1 2 1 1 1 1 1 1 1 1 1 1 1 1 -77 -27 -25 -22 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 AMP 4805 REV 31MAR2000 SEE SHEET 1 DWN APVD - - - - TE CRIMP SPECIFICATION WIRE STRIP LENGTH DATE - FASTIN-FASTON RECEPTACLE SERIE 9.5 TERMINAL NAME: DESCRIPTION - F F 4.57 mm [.180] LTR (QUANTITY 2) TYPE 3.05 mm [.120] P - 6 SIZE 66 - D APPLICATOR DATA A REVISIONS DIST PART NUMBERS REQUIRED PNEUMATIC FEED - LOC 1 mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: PART NO DWN 27SEPT2013 CHK 27SEPT2013 APVD 27SEPT2013 K. STAKEM G. BAILEY T. ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 ITEM NO DESCRIPTION APPLICATION SPEC - 251 250 249 246 244 243 242 240 238 213 186 183 172 166 164 163 153 152 145 144 141 140 139 137 135 133 82 71 70 67 66 64 63 62 57 56 55 54 53 51 49 41 40 39 38 33 31 29 27 25 24 23 22 20 18 16 11 10 9 8 7 6 5 4 3 2 1 FINE ADJUST HEAD ASM, PACIFIC STYLE PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI SPRING, COMPRESSION CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SHCS, LOW HEAD, RoHS, M5 X 10 AIR FEED MODULE TAG,IDENTIFICATION SCR, BHSC, RoHS (M6 X 20) FEED FINGER ASSEMBLY,EF RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER O-RING, .801 ID, .070 DIA. MAT. FEED CAM, AIR FEED DETENT PIN SCR, BHSC, RoHS (M4 X 16) APPLICATOR BASIC ASSEMBLY, EF RAM, ASIAN STYLE, END FEED BOLT, ADJUSTMENT PIN, RETAIN, GRVD, 3/16 X .854 MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM SPACER, CRIMPER DOCUMENTATION PACKAGE SCR, SET, FLT POINT M3 X 10.0 TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SKT HD CAP, RoHS, M4 X 16 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SHCS, LOW HEAD, RoHS, M4 X 8 SCR, SKT HD CAP, RoHS, M4 X 20 NUT, HEX, REG, RoHS, M4 NUT, HEX, REG, RoHS, M3 NUT, LOCK, HEX, TORQUE (M4) PAWL, EF, AIR SCR, SKT HD CAP M4 X 6.0 SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION WASHER, FLAT, REG M4 SCR, SKT HD CAP, RoHS, M4 X 16 SCR, SKT HD CAP, RoHS, M4 X 10 STRIPPER (MACHINING) STUD, THREADED PLATE, STRIP GUIDE PLATE, STRIP HOLD DOWN SPRING, COMPRESSION DRAG GUIDE, LOWER STRIP SPACER PLATE, REAR SHEAR PLATE, FRONT SHEAR ANVIL, COMBINATION, .120 BLADE, SLUG SPACER BLOCK, FL CRIMPER SPACER CRIMPER, INSULATION F PREMIUM SPACER, CRIMPER CRIMPER, WIRE .120 "F" PREMIUM PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH 2119782-1 2119640-1 2079988-1 1-22279-3 2119082-9 2079764-1 2119083-1 2168400-7 2063440-2 2119740-2 2079383-9 1901697-1 21045-3 994969-1 994970-2 240638-1 8-21084-1 2119641-2 2119798-2 2079383-8 2119655-6 2119651-1 2119092-2 3-23627-7 SEE NOTE 4 1633743-1 455888-4 2119956-2 2-18032-2 2119740-1 2168078-1 2168083-8 2119793-1 992763-5 2168400-4 2168083-9 5018030-2 5018030-1 986965-8 2119792-2 18023-9 2079383-7 2119645-1 2119957-1 2119644-2 1-18028-2 2168083-8 1-2168083-0 240639-1 1320906-1 1752371-6 240825-1 2-22281-3 1752373-4 1901259-6 240641-7 240833-7 1-690482-2 1333220-4 2217206-8 5-240641-7 238009-1 2119582-3 1-455888-4 456409-3 Ocean End Feed Applicator - DRAWING NO 2150369 SCALE 1:1 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV B D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC REVISIONS DIST A ALL RIGHTS RESERVED. 1 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - 251 40 62 6 38 39 D 7 7 D 145 153 246 139 140 244 243 6 2 166 242 FEED TYPE 2 2 56 2 11 PNEUMATIC 7 16 8 5 63 238 249 82 1 C 2 250 A 1 137 C 163 2 3 172 1 70 4 51 54 41 55 20 10 A 2 164 64 57 33 23 SERVO LATCH PLATE 18 67 213 B 66 B CAM POSITIONS 30mm STROKE SERVO FEEDER NOT INCLUDED A 152 29 33 27 8 1 141 144 31 9 1 11 186 53 33 25 22 24 4 133 135 183 240 REF 49 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. AIR FEED PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: 27SEPT2013 CHK 27SEPT2013 APVD 27SEPT2013 K. STAKEM G. BAILEY T. ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH DWN - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean End Feed Applicator - DRAWING NO 2150369 SCALE 1:1 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV B