LD39115J 150 mA low quiescent current low noise voltage regulator Datasheet - production data • Internal current and thermal limit • Flip-chip 4 bumps 0.8 x 0.8 mm. pitch 0.4 mm • Temperature range: -40 °C to 125 °C Applications • Mobile phones Flip-chip 4 • Personal digital assistants (PDAs) • Cordless phones and similar battery-powered systems Features • Input voltage from 1.5 to 5.5 V • Ultra low dropout voltage (80 mV typ. at 100 mA load) • Very low quiescent current (20 µA typ. at no load, 35 µA typ. at 150 mA load, 1 µA max in off mode) • Very low noise (33 µVRMS from 1 kHz to 100 kHz at VOUT = 1.8 V) • Output voltage tolerance: ± 2.0 % @ 25 °C • 150 mA guaranteed output current • Wide range of output voltages available on request: 0.8 V to 4.5 V with 100 mV step • Logic-controlled electronic shutdown Description The LD39115J provides 150 mA maximum current from an input voltage ranging from 1.5 V to 5.5 V with a typical dropout voltage of 80 mV. It is stabilized with a ceramic capacitor. The ultra low drop voltage, low quiescent current and low noise features make it suitable for low power battery-powered applications. Power supply rejection is 65 dB at low frequencies and starts to roll off at 10 kHz. An enable logic control function puts the LD39115J in shutdown mode allowing a total current consumption lower than 1 µA. The device also includes a short-circuit constant current limiting and thermal protection. • Compatible with ceramic capacitor COUT = 1 µF Table 1. Device summary Order codes Output voltages LD39115J10R 1V LD39115J12R 1.2 V LD39115J14R 1.4 V LD39115J15R 1.5 V LD39115J18R 1.8 V LD39115J25R 2.5 V LD39115J28R 2.8 V LD39115J30R 3.0 V LD39115J33R 3.3 V January 2014 This is information on a product in full production. DocID15527 Rev 6 1/21 www.st.com Contents LD39115J Contents 1 Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 6 Typical performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 7 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 8 Packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 9 Different output voltage versions of the LD39115J available on request . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 10 2/21 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 DocID15527 Rev 6 LD39115J 1 Diagram Diagram Figure 1. Block diagram OUT IN BandGap 1.22 V R1 Trimming Thermal Protection R2 Enable EN GND DocID15527 Rev 6 3/21 21 Pin configuration 2 LD39115J Pin configuration Figure 2. Pin connection (top view) Table 2. Pin description 4/21 Pin n° Symbol A2 EN A1 GND B2 IN B1 OUT Function Enable pin logic input: Low = shutdown, High = active Common ground Input voltage of the LDO Output voltage DocID15527 Rev 6 LD39115J 3 Typical application Typical application Figure 3. Typical application circuit VIN IN 1 µF VEN VOUT OUT 1 µF EN Load GND DocID15527 Rev 6 5/21 21 Maximum ratings 4 LD39115J Maximum ratings Table 3. Absolute maximum ratings Symbol VIN Parameter DC input voltage Value Unit - 0.3 to 6 V VOUT DC output voltage - 0.3 to VI + 0.3 V VEN Enable input voltage - 0.3 to VI + 0.3 V IOUT Output current Internally limited mA Power dissipation Internally limited mW PD TSTG Storage temperature range - 65 to 150 °C TOP Operating junction temperature range - 40 to 125 °C Note: Absolute maximum ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied. All values are referred to GND. Table 4. Thermal data Symbol RthJA 6/21 Parameter Thermal resistance junction-ambient DocID15527 Rev 6 Value Unit 180 °C/W LD39115J 5 Electrical characteristics Electrical characteristics TJ = 25 °C, VIN = VOUT(NOM) + 1 V, CIN = COUT = 1 µF, IOUT = 1 mA, VEN = VIN, unless otherwise specified. Table 5. Electrical characteristics for LD39115J (1) Symbol Parameter VIN Operating input voltage Test conditions Min. 1.5 Turn-on threshold VUVLO VOUT 1.45 Turn-off threshold VOUT accuracy Typ. 1.30 Max. Unit 5.5 V 1.48 V 1.35 mV VOUT>1.5 V, IOUT = 1 mA, TJ = 25 °C -2.0 2.0 % VOUT>1.5 V, IOUT = 1 mA, -40 °C<TJ<125 °C -3.0 3.0 % VOUT ≤ 1.5 V, IOUT = 1 mA ±10 mV VOUT ≤ 1.5 V, IOUT = 1 mA, -40 °C<TJ<125 °C ±30 mV 0.01 %/V 10 mVpp ΔVOUT Static line regulation VOUT +1 V ≤ VIN ≤ 5.5 V, IOUT = 1 mA ΔVOUT Transient line regulation(2) ΔVIN = +500 mV, IOUT = 1 mA, TR = TF = 5 µs ΔVOUT Static load regulation IOUT = 1 mA to 150 mA 0.002 %/mA ΔVOUT Transient load regulation(2) IOUT = 1 mA to 150 mA, tR = tF = 5 µs 40 mVpp VDROP Dropout voltage(3) IOUT = 100 mA, VOUT>1.5 V -40 °C<TJ<125 °C 80 Output noise voltage 10 Hz to 100 kHz, IOUT = 10 mA 30 VIN = VOUTNOM+1 V+/-VRIPPLE VRIPPLE = 0.1 V Freq. = 1 kHz IOUT = 10 mA 74 VIN = VOUTNOM+0.5 V+/-VRIPPLE VRIPPLE = 0.1 V Freq. = 10 kHz IOUT = 10 mA 67 IOUT = 0 mA 20 eN SVR Supply voltage rejection VOUT = 1.5 V IOUT = 0 to 150 mA Quiescent current DocID15527 Rev 6 µVRMS/V 50 35 µA IOUT = 0 to 15 0mA, -40 °C<TJ<125 °C VIN input current in OFF MODE: VEN = GND mV dB IOUT = 0 mA, -40 °C<TJ<125 °C IQ 110 70 0.001 1 7/21 21 Electrical characteristics LD39115J Table 5. Electrical characteristics for LD39115J (continued)(1) Symbol ISC Parameter Short circuit current RL = 0 Enable input logic low VIN = 1.5 V to5.5 V, -40 °C<TJ<125 °C Enable input logic high VIN = 1.5 V to 5.5 V, -40 °C<TJ<125 °C VEN IEN TON TSHDN COUT Test conditions Min. Max. 200 Unit mA 0.4 V 0.9 Enable pin input current VSHDN = VIN Turn on time Typ. 0.1 (4) 100 30 Thermal shutdown 160 Hysteresis 20 nA µs °C Output capacitor Capacitance (see Section 6: Typical performance characteristics) 1 22 µF 1. For VOUT(NOM) < 1.2 V, VIN = 1.5 V. 2. All transient values are guaranteed by design, not production tested. 3. Dropout voltage is the input-to-output voltage difference at which the output voltage is 100 mV below its nominal value. This specification does not apply for output voltages below 1.5 V. 4. Turn-on time is time measured between the enable input just exceeding VEN high value and the output voltage just reaching 95 % of its nominal value. 8/21 DocID15527 Rev 6 LD39115J 6 Typical performance characteristics Typical performance characteristics CIN = COUT = 1 µF, VEN to VIN. Figure 4. Output voltage vs. temperature (VOUT = 1.2 V) 1.3 Figure 5. Output voltage vs. temperature (VOUT = 2.8 V) 3 VIN = 2.2 V, IOUT = 1 mA 1.28 1.26 2.9 1.24 1.22 1.2 VOUT [V] VOUT [V] VIN = 3.8 V, IOUT = 1 mA 2.95 1.18 1.16 2.85 2.8 2.75 2.7 1.14 1.12 VOUT = 1.2 V VOUT = 2.8 V 2.65 1.1 2.6 -75 -50 -25 0 25 50 75 100 125 150 175 -75 -50 -25 0 25 T [°C] Figure 6. Line regulation vs. temperature 75 100 125 150 175 Figure 7. Load regulation vs. temperature 0.004 0.05 VIN = from 2.2 V to 5.5 V, IOUT = 1 mA VIN = 2.2 V, IOUT = from 1 to 150 mA 0.0035 Load [%/mA] 0.04 Line [%/V] 50 T [°C] 0.03 VOUT=1.2V 0.02 0.003 0.0025 0.002 0.0015 0.001 0.01 0.0005 VOUT=1.2 V 0 0 -75 -50 -25 0 25 50 75 -75 100 125 150 175 -50 -25 0 25 Figure 8. Short-circuit current vs. drop voltage 0.35 0.08 85 0.07 55 0.3 ISC [A] 125 25 0.25 0 0.2 -25 0.15 -40 VDROPOUT [V] 0.4 100 125 150 175 IOUT = 0.1 A 0.06 0.05 0.04 0.03 0.02 CIN = 1 µF COUT = 1 µF(+ 10 µF electrolitycs) 0.05 75 Figure 9. Dropout voltage vs. temperature 0.09 0.45 0.1 50 T [°C] T [°C] VOUT = 2.8 V 0.01 0 0 1 2 3 4 5 6 0 -75 -50 -25 0 25 50 75 100 125 150 175 DROP [V] TEMPERATURE [°C] DocID15527 Rev 6 9/21 21 Typical performance characteristics LD39115J Figure 11. Output voltage vs. input voltage (VOUT = 1.3 V) 0.14 1.4 0.12 1.2 125 0.1 0.08 0.06 0.04 25 0 0.6 -25 0.4 -40 0.2 VOUT = 1.3 V 0 VOUT = 2.8 V 0 0 0.05 0.1 0.15 0.2 55 0.8 0.02 0 85 IOUT = 0.15 A 1 VOUT [V] VDROPOUT [V] Figure 10. Dropout voltage vs. output current 1 2 3 4 5 6 VIN [V] 0.25 IOUT [A] Figure 12. Output voltage vs. input voltage (VOUT = 2.8 V) 3 Figure 13. Enable threshold vs. temperature 125 IOUT = 0.15 A 85 2.5 25 0 1.5 -25 1 -40 VOUT = 2.8 V VEN [V] VOUT [V] 55 2 0.5 0 0 1 2 3 4 5 6 VIN [V] 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 VIN = 2.2 V, IOUT = 1 mA -75 -50 -25 0 25 50 75 100 125 150 175 TEMPERATURE [°C] Figure 14. Quiescent current vs. temperature (VOUT = 1.2 V, IOUT = 0 mA) 45 40 Figure 15. Quiescent current vs. temperature (VOUT = 1.2 V, IOUT = 0.15 A) 70 VIN = 2.2 V, No Load 60 VIN = 2.2 V, IOUT = 0.15 A 50 30 IQ [µA] IQ [µA] 35 25 20 15 40 30 20 10 VOUT = 1.2 V 10 5 VOUT = 1.2 V 0 -75 -50 -25 0 25 50 75 100 125 150 175 0 -75 -50 -25 25 50 75 100 125 150 175 TEMPERATURE [°C] TEMPERATURE [°C] 10/21 0 DocID15527 Rev 6 LD39115J Typical performance characteristics Figure 16. Quiescent current vs. temperature (VOUT = 2.8 V, IOUT = 0.15 A) Figure 17. Quiescent current vs. input voltage 70 VIN = 3.8 V, IOUT = 0.15 A 60 IQ [µA] IQ [µA] 50 40 30 20 VOUT = 2.8 V 10 0 -75 -50 -25 0 25 50 75 25 22.5 20 17.5 15 12.5 10 7.5 5 2.5 0 IOUT = 1 mA VOUT = 1.3 V 0 100 125 150 175 0.5 1 1.5 2 2.5 3 Figure 18. Quiescent current vs. output current 5.5 6 Figure 19. Supply voltage rejection vs. temperature (VOUT = 1.2 V) 100 VIN = 2.3 V VIN from 2.1 V to 2.3 V IOUT = 10 mA, Freq. = 1 kHz 90 SVR [dB] IQ [µA] 4.5 5 VIN [V] TEMPERATURE [°C] 50 45 40 35 30 25 20 15 10 5 0 3.5 4 80 70 60 VOUT = 1.2 V 50 VOUT = 2.8 V 40 0 0.025 0.05 0.075 0.1 0.125 0.15 0.175 0.2 0.225 -75 -50 -25 0 25 50 75 100 125 150 175 T [°C] IOUT [A] DocID15527 Rev 6 11/21 21 Typical performance characteristics LD39115J Figure 20. Supply voltage rejection vs. temperature (VOUT = 1.3 V) Figure 21. Supply voltage rejection vs. temperature (Freq. = 1 kHz) 100 100 VIN from 3.7 V to 3.9 V, IOUT = 10 mA, Freq. = 1 kHz 90 90 80 80 SVR [dB] SVR [dB] VIN from 2.2 V to 2.4 V, IOUT = 10 mA, Freq. = 1 kHz 70 70 60 60 VOUT = 1.3 V 50 50 40 40 VOUT = 2.8 V -75 -50 -25 0 25 50 75 -75 -50 -25 100 125 150 175 0 25 T [°C] Figure 22. Supply voltage rejection vs. temperature (Freq. = 10 kHz) 75 100 125 150 175 Figure 23. Supply voltage rejection vs. temperature (VOUT = 2.8 V) 100 100 VIN from 3.2 V to 3.4 V, IOUT = 10 mA, Freq. = 10 kHz VIN from 1.7 V to 1.9 V, IOUT = 10 mA, Freq. = 10 kHz 90 90 80 80 SVR [dB] SVR [dB] 50 T [°C] 70 70 60 60 50 50 VOUT = 2.8 V VOUT = 1.3 V 40 40 -75 -50 -25 0 25 50 75 -75 -50 -25 100 125 150 175 0 25 T [°C] VIN from 2.1 V to 2.3 V, IOUT = 10 mA VOUT = 1.2 V 0 10 20 30 40 50 60 70 80 90 100 110 100 90 80 70 60 50 40 30 20 10 0 100 125 150 175 VIN from 1.7 V to 1.9 V, IOUT = 10 mA VOUT = 1.3 V 0 10 20 30 40 50 60 70 Frequency [KHz] Frequency [kHz] 12/21 75 Figure 25. Supply voltage rejection vs. frequency (VOUT = 1.3 V) SVR [dB] SVR [dB] Figure 24. Supply voltage rejection vs. frequency (VOUT = 1.2 V) 100 90 80 70 60 50 40 30 20 10 0 50 T [°C] DocID15527 Rev 6 80 90 100 110 LD39115J Typical performance characteristics Figure 27. Supply voltage rejection vs. output current 100 100 90 80 70 60 50 40 30 20 10 0 VIN from 3.2 V to 3.4 V, IOUT = 10 mA VIN from 1.7 V to 1.9 V, F = 10 kHz 90 80 70 SVR [dB] SVR [dB] Figure 26. Supply voltage rejection vs. frequency (VOUT = 2.8 V) 60 50 40 30 VOUT = 2.8 V VOUT = 1.3 V 20 10 0 0 0 10 20 30 40 50 60 70 80 90 100 110 120 0.025 0.05 0.075 0.1 0.125 0.15 0.175 0.2 0.225 0.25 IOUT [A] Frequency [kHz] Figure 28. LD39115J noise Figure 29. Line regulation transient Noise [µV/SQRT(Hz)] 1 VOUT = 1.3 V, VIN = 2.3 V, TA = 25 °C 0.8 0.6 VIN 0.4 0.2 VOUT 0 0 20000 40000 60000 80000 100000 Freq [Hz] VIN from 2.2 V to 2.7 V, IOUT = 1 mA, COUT = 1 µF, No CIN tRISE/FALL = 5 µs Figure 30. Start up transient Figure 31. Enable transient (VOUT = 1.2 V) VIN VEN VOUT VOUT VIN from 0 to 2.3 V, IOUT = 1 mA COUT = 1 µF No CIN, tRISE = 60 µs VOUT = 1.2 V VIN = 2.3 V, VEN from 0 to 2 V, IOUT = 1 mA, Trise = 5 µs DocID15527 Rev 6 13/21 21 Typical performance characteristics LD39115J Figure 32. Enable transient (VOUT = 2.8 V) Figure 33. Load transient (VOUT = 1.2 V) IOUT VEN VOUT = 1.2 V VOUT VOUT = 2.8 V VIN = 3.8 V, VEN from 0 to 2 V, IOUT = 1 mA, tRISE = 5 µs VOUT VIN = 2. 2 V, IOUT = from 1 to 150 mA, tRISE/FALL = 5 µs Figure 34. Load transient (VOUT = 2.8 V) Figure 35. ESR required for stability with ceramics capacitors 2.5 IOUT VOUT VOUT = 2.8 V ESR @ 100 kHz[ohm] 2.25 UNSTABLE ZONE 2 1.75 1.5 IOUT = from 1 mA to 150 mA, CIN = 1µF (ceramic) 1.25 1 STABLE ZONE 0.75 0.5 0.25 0 1 Vin = 3.8 V, IOUT = from 1 to 150 mA, tRISE/FALL = 5 µs 14/21 DocID15527 Rev 6 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 COUT [µF] (nominal value) LD39115J 7 Package mechanical data Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. Figure 36. Flip-chip 4 drawings DocID15527 Rev 6 15/21 21 Package mechanical data LD39115J Table 6. Flip-chip 4 mechanical data mm Dim. Min. Typ. Max. A 0.52 0.56 0.60 A1 0.17 0.20 0.23 A2 0.35 0.36 0.37 b 0.23 0.25 0.29 D 0.758 0.788 0.818 D1 E 0.4 0.758 E1 0.788 0.4 SD 0.18 0.2 0.22 SE 0.18 0.2 0.22 f 0.199 ccc 0.075 Figure 37. Flip-chip 4 footprint 16/21 0.818 DocID15527 Rev 6 LD39115J 8 Packaging mechanical data Packaging mechanical data Figure 38. Flip-chip 4 tape and reel drawing DocID15527 Rev 6 17/21 21 Packaging mechanical data LD39115J Table 7. Flip-chip 4 tape and reel mechanical data mm Dim. Min. Typ. A 178 C 12.8 D 20.2 N 59 13.2 60 T 18/21 Max. 61 8.4 Ao 0.82 0.87 0.92 Bo 0.82 0.87 0.92 Ko 0.64 0.69 0.74 Po 3.9 4.0 4.1 P 3.9 4.0 4.1 DocID15527 Rev 6 LD39115J 9 Different output voltage versions of the LD39115J available on request Different output voltage versions of the LD39115J available on request Table 8. Options available on request Order codes Output voltages LD39115J08R 0.8 V LD39115J10R 1.0 V DocID15527 Rev 6 19/21 21 Revision history 10 LD39115J Revision history Table 9. Document revision history Date Revision 26-Mar-2009 1 Initial release. 12-Jun-2009 2 Modified: Table 1 on page 1 and Table 8 on page 19. 05-Aug-2009 3 Modified: tape and reel mechanical data on page 18. 17-May-2011 4 Modified: Table 1 on page 1 and Table 8 on page 19. 20-Dec-2011 5 Added: new order code LD39115J25R Table 1 on page 1. 6 Part number LD39115Jxx changed to LD39115J. Updated the Description in cover page, Section 7: Package mechanical data. Added Section 8: Packaging mechanical data. Minor text changes. 16-Jan-2014 20/21 Changes DocID15527 Rev 6 LD39115J Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2014 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com DocID15527 Rev 6 21/21 21