MD200xE Series Low Cost, 2W Miniature SIP DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: • 2W Output Power Input Parameter Conditions Min. 5 VDC Input 4.50 9 VDC Input 8.10 12 VDC Input 10.80 15 VDC Input 13.50 24 VDC Input 21.60 Internal Capacitor • Miniature SIP Case • Short Circuit Protected Input Voltage Range • 1,500 VDC Isolation • 57 Standard Models Input Filter • Single and Dual Outputs Output • >3.5 MHour MTBF • -40°C to +105°C Operation • LOW COST Parameter Output Voltage Accuracy 3.3 VDC Output Line Regulation All Other Outputs Load Regulation, See Note 1 Ripple & Noise (20 MHz), See Note 2 3.0 kV Isolation Models Available Conditions Min. Typ. 5.0 9.0 12.0 15.0 24.0 Max. 5.50 9.90 13.20 16.50 26.40 Units Typ. ±2.5 Max. Units % ±1.5 ±1.2 For VIN Change of 1% See Model Selection Guide Output Voltage <12 VDC 60 15 VDC, 24 VDC Output 75 Temperature Coefficient Output Short Circuit VDC % mV P - P ±0.03 %/°C Typ. Max. 20 100 300 Units VDC M pF kHz Continuous (Autorecovery) General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency EMI Characteristics Parameter Conditions 60 Seconds 500 VDC 100 kHz, 1V Conditions EMC Compliance, Single Output EMC Compliance, Dual Output Min. Conducted Radiated EMI Compliance, See Note 4 Min. 1,500 1,000 Electrostatic Discharge (ESD) Typ. Max. Units CISPR22/EN 55022 Level B CISPR22/EN 55022 Level B EN 61000-4-2 Level B Contact ±8 kV EN 61000-4-2 Level B Contact ±6 kV Environmental MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Physical Case Size Case Material Weight Conditions Min. Typ. -40 +25 -55 Free Air Convection RH, Non-condensing Ambient Max. +105 +125 Units °C °C 95 % 0.772 x 0.276 x 0.394 Inches (19.6 x 7.0 x 10.0 mm) Non-Conductive Black Plastic (UL-94V0) 0.08 Oz (2.4g) Reliability Specifications Parameter MTBF Conditions MIL HDBK 217F, 25°C, Gnd Benign Min. 3.5 Typ. Max. Units MHours Min. -0.7 -0.7 -0.7 -0.7 -0.7 Typ. Max. 9.0 12.0 18.0 21.0 30.0 300 Units Absolute Maximum Ratings T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Parameter Conditions Input Voltage Surge (1 Sec) Lead Temperature 5 VDC Input 9 VDC Input 12 VDC Input 15 VDC Input 24 VDC Input 1.5 mm From Case For 10 Sec Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. www.micropowerdirect.com VDC °C www.micropowerdirect.com Model Selection Guide Model Number MD205S-03E MD205S-05E MD205S-09E MD205S-12E MD205S-15E MD205S-24E MD205D-03E MD205D-05E MD205D-09E MD205D-12E MD205D-15E MD205D-24E MD209S-05E MD209S-09E MD209S-12E MD209S-15E MD209S-24E MD209D-05E MD209D-09E MD209D-12E MD209D-15E MD209D-24E MD212S-03E MD212S-05E MD212S-09E MD212S-12E MD212S-15E MD212S-15E MD212D-03E MD212D-05E MD212D-07E MD212D-09E MD212D-12E MD212D-15E MD212D-24E MD215S-05E MD215S-09E MD215S-12E MD215S-15E MD215S-24E MD215D-05E MD215D-09E MD215D-12E MD215D-15E MD215D-24E MD224S-03E MD224S-05E MD224S-09E MD224S-12E MD224S-15E MD224S-24E MD224D-03E MD224D-05E MD224D-09E MD224D-12E MD224D-15E MD224D-24E Input Voltage (VDC) Current (mA) Nominal Range Full-Load No-Load 5 4.5 - 5.5 476 25 5 4.5 - 5.5 506 25 5 4.5 - 5.5 506 25 5 4.5 - 5.5 476 25 5 4.5 - 5.5 476 25 5 4.5 - 5.5 476 25 5 4.5 - 5.5 540 25 5 4.5 - 5.5 500 25 5 4.5 - 5.5 476 25 5 4.5 - 5.5 476 25 5 4.5 - 5.5 476 25 5 4.5 - 5.5 476 25 9 8.1 - 9.9 285 20 9 8.1 - 9.9 281 20 9 8.1 - 9.9 274 20 9 8.1 - 9.9 274 20 9 8.1 - 9.9 274 20 9 8.1 - 9.9 285 20 9 8.1 - 9.9 281 20 9 8.1 - 9.9 274 20 9 8.1 - 9.9 274 20 9 8.1 - 9.9 274 20 12 10.8 - 13.2 198 15 12 10.8 - 13.2 213 15 12 10.8 - 13.2 211 15 12 10.8 - 13.2 198 15 12 10.8 - 13.2 198 15 12 10.8 - 13.2 198 15 12 10.8 - 13.2 208 15 12 10.8 - 13.2 198 15 12 10.8 - 13.2 198 15 12 10.8 - 13.2 205 15 12 10.8 - 13.2 196 15 12 10.8 - 13.2 198 15 12 10.8 - 13.2 196 15 15 13.5 - 16.5 171 10 15 13.5 - 16.5 169 10 15 13.5 - 16.5 159 10 15 13.5 - 16.5 157 10 15 13.5 - 16.5 157 10 15 13.5 - 16.5 167 10 15 13.5 - 16.5 167 10 15 13.5 - 16.5 159 10 15 13.5 - 16.5 157 10 15 13.5 - 16.5 157 10 24 21.6 - 26.4 99 8 24 21.6 - 26.4 104 8 24 21.6 - 26.4 100 8 24 21.6 - 26.4 99 8 24 21.6 - 26.4 99 8 24 21.6 - 26.4 98 8 24 21.6 - 26.4 104 8 24 21.6 - 26.4 99 8 24 21.6 - 26.4 98 8 24 21.6 - 26.4 99 8 24 21.6 - 26.4 99 8 24 21.6 - 26.4 98 8 Voltage Output Current (VDC) (mA, Max) 3.3 5.0 9.0 12.0 15.0 24.0 ±3.3 ±5.0 ±9.0 ±12.0 ±15.0 ±24.0 5.0 9.0 12.0 15.0 24.0 ±5.0 ±9.0 ±12.0 ±15.0 ±24.0 3.3 5.0 9.0 12.0 15.0 24.0 ±3.3 ±5.0 ±7.2 ±9.0 ±12.0 ±15.0 ±24.0 5.0 9.0 12.0 15.0 24.0 ±5.0 ±9.0 ±12.0 ±15.0 ±24.0 3.3 5.0 9.0 12.0 15.0 24.0 ±3.3 ±5.0 ±9.0 ±12.0 ±15.0 ±24.0 Notes: 1. Output load regulation is specified for a load change of 10% to 100%. 2. When measuring output ripple, it is recommended that an external 1 µF ceramic capacitor & 10 µF electrolytic capacitor be placed in parallel from the +Vout pin to the -Vout pin for single output models, or from each output to common for dual output models. 3. Operation at no load will not damage these units, however, they may not meet all specifications. 4. These converters are specified for operation without external components. However, in some applications the addition of input/output capacitors will enhance stability and reduce output ripple. The simple connection shown on page 3 will typically meet EN 55022 Class B. For dual output units, a capacitor should be connected from each output to common. 292 Page Street Ste D Stoughton, MA 02072 400 400 222 167 133 83 ±303 ±200 ±111 ±83 ±67 ±42 400 222 167 133 83 ±200 ±111 ±83 ±67 ±42 400 400 222 167 133 83 ±303 ±200 ±139 ±111 ±83 ±67 ±42 400 222 167 133 83 ±200 ±111 ±83 ±67 ±42 400 400 222 167 133 83 ±303 ±200 ±111 ±83 ±67 ±42 Output Load Regulation Capacitive Load (mA, Min) (µF Max) % Typ. 40.0 18.0 220 40.0 12.0 220 22.0 9.0 220 17.0 8.0 220 13.0 7.0 220 8.0 6.0 220 ±30.0 18.0 100 ±20.0 12.0 100 ±11.0 9.0 100 ±8.0 8.0 100 ±7.0 7.0 100 ±4.0 6.0 100 40.0 12.0 220 22.0 9.0 220 17.0 8.0 220 13.0 7.0 220 8.0 6.0 220 ±20.0 12.0 100 ±11.0 9.0 100 ±8.0 8.0 100 ±7.0 7.0 100 ±4.0 6.0 100 40.0 18.0 220 40.0 12.0 220 22.0 9.0 220 17.0 8.0 220 13.0 7.0 220 8.0 6.0 220 ±30.0 18.0 100 ±20.0 12.0 100 ±14.0 10.0 100 ±11.0 9.0 100 ±8.0 8.0 100 ±7.0 7.0 100 ±4.0 6.0 100 40.0 12.0 220 22.0 9.0 220 17.0 8.0 220 13.0 7.0 220 8.0 6.0 220 ±20.0 12.0 100 ±11.0 9.0 100 ±8.0 8.0 100 ±7.0 7.0 100 ±4.0 6.0 100 40.0 18.0 220 40.0 12.0 220 22.0 9.0 220 17.0 8.0 220 13.0 7.0 220 8.0 6.0 220 ±30.0 18.0 100 ±20.0 12.0 100 ±11.0 9.0 100 ±8.0 8.0 100 ±7.0 7.0 100 ±4.0 6.0 100 Efficiency (%) Current Fuse Rating Slow-Blow Min. Typ. (mA) 70 75 77 80 80 80 70 76 80 80 80 80 76 77 79 79 79 76 77 79 79 79 75 86 77 80 80 81 76 80 80 79 81 80 82 76 77 80 80 81 76 76 80 81 81 75 76 79 80 80 80 76 80 81 80 80 81 74 79 81 84 84 84 74 80 84 84 84 84 80 81 83 83 83 80 81 83 83 83 79 80 81 84 84 85 80 84 84 83 85 84 86 80 81 84 84 85 80 80 84 85 85 79 80 83 84 84 84 80 84 85 84 84 85 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 750 750 750 750 750 750 750 750 750 750 500 500 500 500 500 500 500 500 500 500 500 500 500 400 400 400 400 400 400 400 400 400 400 250 250 250 250 250 250 250 250 250 250 250 250 Derating Curve • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected] www.micropowerdirect.com Typical Efficiency vs Input, 5 VIN Models Typical Efficiency vs Input, 12 VIN Models Typical Efficiency vs Output, 5 VIN Models Typical Efficiency vs Output, 12 VIN Models Efficiency vs input is plotted with the unit at full load. Efficiency vs output is plotted with the unit at nominal input. Typical Connection, Single Output Models Typical Connection, Dual Output Models VIN C1 L1 3.3 VDC 5 VDC 12 VDC 15 VDC 24 VDC 4.7 µF/50V 4.7 µF/50V 4.7 µF/50V 4.7 µF/50V 4.7 µF/50V 6.8 µH 6.8 µH 6.8 µH 6.8 µH 6.8 µH VOUT 3.3 VDC 5.0 VDC 9.0 VDC 12 VDC 15 VDC 24 VDC ±3.3 VDC ±5.0 VDC ±9.0 VDC ±12 VDC ±15 VDC ±24 VDC C2 10 µF 10 µF 2.2 µF 2.2 µF 1.0 µF 1.0 µF 4.7 µF 4.7 µF 1.0 µF 1.0 µF 0.47 µF 0.47 µF C3 10 µF 10 µF 2.2 µF 2.2 µF 1.0 µF 1.0 µF 4.7 µF 4.7 µF 1.0 µF 1.0 µF 0.47 µF 0.47 µF These converters are specified for operation without external components. However, in some applications the addition of input/output capacitors will enhance stability and reduce output ripple. For applications that require meeting EMC standards, the diagrams above illustrates a typical connection of the MD200x-xxE series. Suggested component values are given in the table at right. Capacitors C2 and C3 are not required to meet specifications, but may be used if a lower level of output ripple is required. MicroPower Direct • 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected] The drawings below show typical board layouts for the EMC circuits shown on page three (one for single output models and one for dual output units). www.micropowerdirect.com Typical Board Layout, Single Output Models Typical Board Layout, Dual Output Models Mechanical Dimensions Pin Connections Notes: • All dimensions are typical in inches (mm) • General Tolerance x.xx = ±0.02 (±0.5) • Pin 1 is marked by a “dot” or indentation on the unit Pin 1 2 4 5 6 Single Output +VIN -VIN -VOUT No Pin +VOUT Pin 1 2 4 5 6 Dual Output +VIN -VIN -VOUT Common +VOUT MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]