AZ762P 20 AMP LATCHING POWER RELAY FEATURES • • • • Dielectric strength 4000 Vrms Low height: 16 mm 20 Amp switching UL, CUR file E44211 CONTACTS GENERAL DATA Arrangement SPDT (1 Form C) SPST (1 Form A) Life Expectancy Mechanical Electrical Minimum operations 1 x 106 1 x 105 Set Time (typical) 10 ms at nominal coil voltage Max. switched power: 5000 VA Max. switched current: 20 A Max. inrush current “1AT” version: 165 A , 20 ms 500 A, 2 ms 800 A, 200 µs Max. switched voltage: 125VDC* or 350 VAC Reset Time (typical) 10 ms at nominal coil voltage Min. Pulse Time 75 ms Max. Pulse Time 1 min. Dielectric Strength (at sea level for 1 min.) 4000 Vrms coil to contact 1000 Vrms between open contacts * Note: Insulation Resistance 1000 megaohms min. at 20°C 500 VDC 50% RH Insulation (according to DIN VDE 0110, IEC 60664-1) C250 Overvoltage category: III Pollution degree: 3 Nominal voltage: 250 VAC Ambient Temperature Operating At nominal coil voltage -40°C (-40°F) to 85°C (185°F) Vibration 0.062” (1.5 mm) DA at 10-55 Hz Shock 10 g Enclosure P.B.T. polyester Terminals tinned copper alloy, P.C. Max. Solder Temp. 270°C (518°F) Max. Solder Time 5 seconds Max. Solvent Temp. 80°C (176°F) 1 Form C (normally closed) 16 A at 250 VAC, resistive, 50k cycles, 85°C [1] Max. Immersion Time 30 seconds Weight 13 grams Material Silver tin oxide [1], Silver tin oxide + tungsten [2] Packing unit in pcs. 50 per tray / 500 per carton box Resistance < 20 milliohms initially Ratings Rated Load UL, CUR Resistive load: If switching voltage is greater than 30 VDC, special precautions must be taken. Please contact the factory. 1 Form A 20 A at 250 VAC, resistive, 20k cycles, 70°C [1] 16 A at 250 VAC, resistive, 100k cycles, 85°C [1] 6 A at 277 VAC, tungsten, 6k cycles, 40°C [1] 6 A at 277 VAC, standard ballast, 6k cycles, 40°C [1] 1.5 HP at 250 VAC, 40°C [1] 3300 W at 277 VAC, electronic ballast, 20k cycles, 40°C [2] 3000 W at 220 VAC, tungsten, 6k cycles, 40°C [2] 1500 W at 347 VAC, standard ballast, 20k cycles, 40°C [2] 1 Form C (normally open) 20 A at 250 VAC, resistive, 20k cycles, 70°C [1] 16 A at 250 VAC, resistive, 100k cycles, 85°C [1] NOTES COIL Power At Set/Reset Voltage (typical) Temperature 1. All values at 20°C (68°F). 256 mW (single coil) 384 mW (dual coil) 416 mW (dual coil 24 V) Max. 155°C (311°F) Class F 2. Relay may pull in with less than “Set/Reset” value. 3. Specifications subject to change without notice. 4. Initial state of contacts may be changed during transportation or shock! ZETTLER electronics GmbH Junkersstr. 3, D-82178 Puchheim, Germany phone: +49 89 800 97-0 [email protected] fax: +49 89 800 97-200 www.ZETTLERelectronics.com This product specification to be used only together with the application notes which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf 2013-07-18 AZ762P RELAY ORDERING DATA SINGLE COIL LATCHING COIL SPECIFICATION ORDER NUMBER* Nominal Coil VDC Set/Reset VDC Max. Continuous VDC 3 2.4 3.9 5 4.0 6.5 6 4.8 9 7.2 12 9.6 24 19.2 Coil Resistance Ohm ± 10% 1 Form A 1 Form C 22.5 AZ762P1-1AE-3D AZ762P1-1CE-3D 62.5 AZ762P1-1AE-5D AZ762P1-1CE-5D 7.8 90 AZ762P1-1AE-6D AZ762P1-1CE-6D 11.7 202 AZ762P1-1AE-9D AZ762P1-1CE-9D 15.6 360 AZ762P1-1AE-12D AZ762P1-1CE-12D 31.2 1,440 AZ762P1-1AE-24D AZ762P1-1CE-24D DUAL COIL LATCHING COIL SPECIFICATION ORDER NUMBER* Nominal Coil VDC Set/Reset VDC Max. Continuous VDC 3 2.4 3.9 5 4.0 6 4.8 Coil Resistance Ohm ± 10% 1 Form A 1 Form C 15 AZ762P2-1AE-3D AZ762P2-1CE-3D 6.5 42 AZ762P2-1AE-5D AZ762P2-1CE-5D 7.8 60 AZ762P2-1AE-6D AZ762P2-1CE-6D 9 7.2 11.7 135 AZ762P2-1AE-9D AZ762P2-1CE-9D 12 9.6 15.6 240 AZ762P2-1AE-12D AZ762P2-1CE-12D 24 19.2 31.2 886 AZ762P2-1AE-24D AZ762P2-1CE-24D * “1AE” or “1CE” denote silver tin oxide contacts. Substitute “1AT” in place of “1AE” for silver tin oxide contacts with tungsten premake contact. Add suffix “E” at the end of the order number for sealed version. Add suffix “K” at the end of the order number for 3.5 mm pin spacing version. (not available for “1AT” version) Add suffix “R” at the end of the order number for reversed polarity coil. WIRING DIAGRAM Standard Polarity 1 FORM A Single coil latching 4 4 1 FORM C 4 4 3 3 Single coil latching Dual coil latching 4 3 6 1(+) 2(-) 1(-) SET 2(+) 1(-) 5(+) RESET 5(+) 2(-) SET 4 4 3 3 RESET 4 3 3 6 6 2(-) 1(-) 1(+) Dual coil latching SET 2(+) 3 6 1(-) 5(+) RESET 5(+) 2(-) SET RESET Reversed Polarity 4 4 4 3 4 4 3 3 3 3 6 1(-) 2(+) 1(+) SET 2(-) RESET 1(+) 5(-) SET 5(-) 2(+) RESET 4 4 3 3 6 6 1(-) 4 2(+) 1(+) SET 2(-) RESET 3 6 1(+) 5(-) SET 5(-) 2(+) RESET Viewed toward terminals Contact positions are shown in energized coil state. ZETTLER electronics GmbH Junkersstr. 3, D-82178 Puchheim, Germany phone: +49 89 800 97-0 [email protected] fax: +49 89 800 97-200 www.ZETTLERelectronics.com This product specification to be used only together with the application notes which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf 2013-07-18 AZ762P MECHANICAL DATA PC BOARD LAYOUT 5.0 mm Spacing - Standard version 20.3 12.7 ± 0.3 29.4 ± 0.4 1.55 5 5 2.15 2.75 * 7.5 15.7 ± 0.3 * Not used on single coil version 3 x ø 1.5 3.5 ± 0.3 3 x ø 1.0 0.3 ± 0.2 Not used on 1 Form A version 7.5 ± 0.1 Viewed toward terminals 20.3 ± 0.3 5 ± 0.1 5 ± 0.1 terminal not used on single coil version 3 x 0.5 ± 0.04 * 3 x 1 ± 0.04 3 x 0.5 ± 0.04 3 x 0.5 ± 0.04 * Terminal not used on 1 Form A version 3.5 mm Spacing - "K" version 29.4 ± 0.4 20.3 12.7 ± 0.3 3.05 7.5 15.7 ± 0.3 3.5 3.5 2.15 * 2.75 * Not used on single coil version 3 x ø 1.5 3.5 ± 0.3 0.3 ± 0.2 3 x ø 1.0 Not used on 1 Form A version 7.5 ± 0.1 Viewed toward terminals 20.3 ± 0.3 3.5 ± 0.1 3.5 ± 0.1 terminal not used on single coil version 3 x 0.5 ± 0.04 * 3 x 1 ± 0.04 3 x 0.5 ± 0.04 3 x 0.5 ± 0.04 * Terminal not used on 1 Form A version ZETTLER electronics GmbH Junkersstr. 3, D-82178 Puchheim, Germany phone: +49 89 800 97-0 [email protected] fax: +49 89 800 97-200 www.ZETTLERelectronics.com This product specification to be used only together with the application notes which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf 2013-07-18