TDK MLJ1608WR47T000 Inductors for power circuits multilayer ferrite Datasheet

I
N
D
U
C
T
O
R
S
April 2016
Inductors for Power Circuits
Multilayer Ferrite
MLJ Series
MLJ1608 Type
MLJ1608
1608 [0603 inch]*
* Dimensions Code JIS[EIA]
(2/8)
I
N
D
U
C
T
O
R
S
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
REMINDERS
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
20160411 / inductor_commercial_power_mlj1608_en.fm
(3/8)
I
N
D
U
C
T
O
R
S
Inductors for Power Circuits
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
Multilayer Ferrite
Overview of MLJ1608 Type
FEATURES
The large current response by ferrite material of the new development.
Narrow tolerance response by lamination of high precision.
Significantly reduce high-frequency Loss by adopting a low-loss material.
APPLICATION
NFC circuit for smart phones and PCs, power supply lines for various electronic devices
PART NUMBER CONSTRUCTION
MLJ
Series name
1608
L×W×H Dimensions
(mm)
1608
1.6×0.8×0.8
W
Characteristics
W
Large
current
R16
△
Inductance
(μH)
R16
160
R33
330
R56
560
Inductance
tolerance
J
±5%
K
±10%
T
000
Packaging style
Internal code
T
Taping
000
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
Temperature range
Package quantity
Operating
Storage
temperature
temperature
(pieces/reel)
(°C)
(°C)
MLJ1608
–55 to +125
–55 to +125
4,000
The Storage temperature range is for after the circuit board is mounted.
Individual weight
Type
(mg)
4
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_power_mlj1608_en.fm
(4/8)
I
N
D
U
C
T
O
R
S
MLJ1608 Type
RECOMMENDED REFLOW PROFILE
Preheating
Soldering
Natural
cooling
Peak
T: Temperature
T4
T3
T2
T3
t3
T1
t1
t2
t: Time
Preheating
Temp.
T1
T2
150°C
180°C
Time
t1
60 to 120s
Soldering
Temp.
Time
T3
t2
230°C
30 to 60s
Peak
Temp.
Time
T4
t3
250 to 260°C 10s max.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_power_mlj1608_en.fm
(5/8)
I
N
D
U
C
T
O
R
S
MLJ1608 Type
0.80±0.15
SHAPE & DIMENSIONS
0.30±0.20
0.30±0.20
0.80±0.15
1.60±0.15
Dimensions in mm
0.8
RECOMMENDED LAND PATTERN
0.6
0.8
0.6
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_power_mlj1608_en.fm
(6/8)
I
N
D
U
C
T
O
R
S
MLJ1608 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
L
Q
(nH)
160
220
270
330
390
470
560
Tolerance
±5%±10%
±5%±10%
±5%±10%
±5%±10%
±5%±10%
±5%±10%
±5%±10%
min.
25
25
25
25
25
25
25
L, Q measuring
conditions
Frequency
Current
(MHz)
25
25
25
25
25
25
25
(mA)
1.0
1.0
1.0
1.0
1.0
1.0
1.0
Self-resonant
frequency
DC resistance Rated current
(MHz)min.
330
290
260
230
210
190
170
(ȍ )
0.12±30%
0.20±30%
0.22±30%
0.24±30%
0.28±30%
0.38±30%
0.40±30%
(MHz)typ.
450
400
350
320
290
260
230
Idc-1
(mA)typ.
750
700
650
650
600
600
550
Idc-1
(mA)max.
600
550
550
500
450
400
400
Part No.
Idc-2
(mA)max.
700
600
550
500
450
400
400
MLJ1608WR16 △ T000
MLJ1608WR22 △ T000
MLJ1608WR27 △ T000
MLJ1608WR33 △ T000
MLJ1608WR39 △ T000
MLJ1608WR47 △ T000
MLJ1608WR56 △ T000
The " △ " of the Part Number contains the inductance tolerance code, J (±5%) or K (±10%)
○ Measurement equipment
Measurement item
Product No.
L, Q
4294A+16034G
Self-resonant frequency
E4991A
DC resistance
Type-7561
* Equivalent measurement equipment may be used.
Manufacturer
Keysight Technologies
Keysight Technologies
Yokogawa
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_power_mlj1608_en.fm
(7/8)
I
N
D
U
C
T
O
R
S
MLJ1608 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
10000
Inductance (nH)
WR56
WR47
1000
WR39
WR33
WR27
WR22
WR16
100
10
1
10
100
1000
Frequency(MHz)
○ Measurement equipment
Product No.
Manufacturer
E4991A+16192A
Keysight Technologies
* Equivalent measurement equipment may be used.
Q FREQUENCY CHARACTERISTICS GRAPH
60
WR22
WR16
50
WR33
WR39
WR47
40
Q
WR56
30
WR27
20
10
0
1
10
100
Frequency(MHz)
1000
10000
○ Measurement equipment
Product No.
Manufacturer
4294A+16034G
Keysight Technologies
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_power_mlj1608_en.fm
(8/8)
I
N
D
U
C
T
O
R
S
MLJ1608 Type
PACKAGING STYLE
REEL DIMENSIONS
ø60min.
1.0
2.0±0.5
8.4 +2.0
–0.0
ø13±0.2
14.4max.
ø21±0.8
ø180±2.0
Dimensions in mm
4.0±0.1
Cavity
3.5±0.05
1.5 +0.1
–0.0
Type
MLJ1608
A
1.9±0.2
B
1.1±0.2
K
1.1 max.
A
8.0±0.3
Sprocket hole
1.75±0.1
TAPE DIMENSIONS
K
B
160min.
Drawing direction
4.0±0.1
Taping
200min.
300min.
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_power_mlj1608_en.fm
Similar pages