Freescale Semiconductor Technical Data Document Number: MC33889 Rev. 11.0, 12/2006 System Basis Chip with Low Speed Fault Tolerant CAN Interface 33889 An SBC device is a monolithic IC combining many functions repeatedly found in standard microcontroller-based systems, e.g., protection, diagnostics, communication, power, etc. The 33889 is an SBC having fully protected, fixed 5.0 V low drop-out regulator, with current limit, over-temperature pre-warning and reset. An output drive with sense input is also provided to implement a second 5.0 V regulator using an external PNP. The 33889 has Normal, Standby, Stop and Sleep modes; an internally switched high-side power supply output with two wake-up inputs; programmable timeout or window watchdog, Interrupt, Reset, SPI input control, and a lowspeed fault tolerant CAN transceiver, compatible with CAN 2.0 A and B protocols for module-to-module communications. The combination is an economical solution for power management, high-speed communication, and control in MCU-based systems. SYSTEM BASIS CHIP DW SUFFIX EG SUFFIX (PB-FREE) PLASTIC PACKAGE 98ASB42345B 28-PIN SOICW Features • VDD1: 5.0 V low drop voltage regulator, current limitation, overtemperature detection, monitoring and reset function with total current capability 200 mA • V2: tracking function of VDD1 regulator; control circuitry for external bipolar ballast transistor for high flexibility in choice of peripheral voltage and current supply • Four operational modes • Low standby current consumption in Stop and Sleep modes • Built-in low speed 125 kbps fault tolerant CAN physical interface. • External high voltage wake-up input, associated with HS1 VBAT switch • 150 mA output current capability for HS1 VBAT switch allowing drive of external switches pull-up resistors or relays • Pb-Free Packaging Designated by Suffix Code EG VDD1 Device Temperature Range (TA) Package -40°C to 125°C 28 SOICW MC33889BDW/R2 MCZ33889BEG/R2 MC33889DDW/R2 *MCZ33889DEG/R2 *Recommended for new designs VPWR 33889 5.0 V ORDERING INFORMATION VSUP V2 GND MCU CS SCLK MOSI MISO CS SCLK MOSI MISO V2CTRL V2 HS1 L0 L1 WDOG RTH TXD RXD CANH CANL RST INT SPI Local Module Supply Wake-Up Inputs Safe Circuits Twisted Pair RTL Figure 1. 33889 Simplified Application Diagram Freescale Semiconductor, Inc. reserves the right to change the detail specifications, as may be required, to permit improvements in the design of its products. © Freescale Semiconductor, Inc., 2006. All rights reserved. CAN Bus DEVICE VARIATIONS DEVICE VARIATIONS Table 1. Device Variations Between the 33889D and 33889B Versions (1) Device Part Number Parameters Symbol Differential Receiver, Recessive To Dominant Threshold (By Definition, VDIFF = VCANH-VCANL) VDIFF1 Differential Receiver, Dominant To Recessive Threshold (Bus Failures 1, 2, 5) MC33889B(2) MC33889D(2) Min 3.2 V 3.5 V Typ 2.6 V 3.0 V Max 2.1 V 2.5 V Min 3.2 V 3.5 V Typ 2.6 V 3.0 V Max 2.1 V 2.5 V Min 50 mA 50 mA Typ 75 mA 100 mA Max 110 mA 130 mA Min 50 mA 50 mA Typ 90 mA 140 mA Max 135 mA 170 mA Vcanh max Vsup/2 + 5V Vsup/2 + 4.55V tLOOPRD max N/A 1.5us tLOOPRD-F max N/A 1.9us N/A 3.6us min N/A 8 typ 30 16 max N/A 30 min not specified, 25us spec applied 25us after 4 non consecutive pulses after 4 consecutive pulses VDIFF2 CANH Output Current (VCANH = 0; TX = 0.0) ICANH CANL Output Current (VCANL = 14 V; TX = 0.0) ICANL Detection threshold for Short circuit to Battery voltage loop time Tx to Rx, no bus failure, ISO configuration loop time Tx to Rx, with bus failure, ISO configuration Trait loop time Tx to Rx, with bus failure and +-1.5V gnd shift, tLOOPRD/DR-F+GS 5 node network, ISO configuration Minimum Dominant time for Wake up on CANL or CANH (Tem Vbat mode) T2SPI timing tWAKE T2spi DEVICE BEHAVIOR CANH or CANL open wire recovery principle Reference MC33889B: on page 33 Rx behavior in TermVbat mode Reference MC33889D: on page Rx recessive, no pulse Rx recessive, dominant pulse to signal bus 34 traffic Notes 1. This datasheet uses the term 33889 in the inclusive sense, referring to both the D version (33889D) and the B version (33689B). 2. The 33889D and 33889B versions are nearly identical. However, where variations in characteristic occur, these items will be separated onto individual lines. 33889 2 Analog Integrated Circuit Device Data Freescale Semiconductor INTERNAL BLOCK DIAGRAM INTERNAL BLOCK DIAGRAM 33889 Internal Block Diagram VSUP V2 VDD1 Oscillator HS1 Control INT HS1 L0 V2CTRL Dual Voltage Regulator VSUP Voltage Monitor VDD1 Voltage Monitor Interrupt Watchdog Reset Programmable Wake-Up Inputs WDOG RST L1 Mode Control TX CS SCLK RX SPI Interface MOSI MISO GND VSUP V2 Fault Tolerant CAN Transceiver RTH CAN H CAN L RTL 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 3 PIN CONNECTIONS PIN CONNECTIONS RX TX VDD1 RST INT GND GND GND GND V2CTRL VSUP HS1 L0 L1 1 28 2 27 3 26 4 25 5 24 6 23 7 22 8 21 9 20 10 19 11 18 12 17 13 16 14 15 WDOG CS MOSI MISO SCLK GND GND GND GND CANL CANH RTL RTH V2 Figure 2. 33889 Pin Connections Table 2. Pin Definitions A functional description of each pin can be found in the Functional pin description section page 24. Pin Pin Name Pin Function Formal Name 1 RX Output Receiver Data 2 TX Input Transmitter Data 3 VDD1 Power Voltage Regulator One 5.0 V pin is a 2% low drop voltage regulator for to the microcontroller supply. This is the device reset output pin whose main function is to reset the MCU. Output Definition CAN bus receive data output pin CAN bus receive data input pin 4 RST Output Reset 5 INT Output Interrupt This output is asserted LOW when an enabled interrupt condition occurs. 6 -9, 20 - 23 GND Ground Ground These device ground pins are internally connected to the package lead frame to provide a 33889-to-PCB thermal path. 10 V2CTRL Output Voltage Source 2 Control Output drive source for the V2 regulator connected to the external series pass transistor. 11 VSUP Power Voltage Supply Supply input pin. Input 12 HS1 Output High-Side Output Output of the internal high-side switch. 13 - 14 L0, L1 Input Level 0 - 1 Inputs Inputs from external switches or from logic circuitry. 15 V2 Input Voltage Regulator Two 16 RTH Output RTH Pin for connection of the bus termination resistor to CANH. 17 RTL Output RTL Pin for connection of the bus termination resistor to CANL. 18 CANH Output CAN High CAN high output pin. 19 CANL Output CAN Low CAN low output pin. 24 SCLK Input System Clock 5.0 V pin is a low drop voltage regulator dedicated to the peripherals supply. Clock input pin for the Serial Peripheral Interface (SPI). 33889 4 Analog Integrated Circuit Device Data Freescale Semiconductor PIN CONNECTIONS Table 2. Pin Definitions (continued) A functional description of each pin can be found in the Functional pin description section page 24. Pin Pin Name Pin Function Formal Name Definition 25 MISO Output Master In/Slave Out SPI data sent to the MCU by the 33889. When CSLOW is HIGH, the pin is in the high impedance state. 26 MOSI Input Master Out/Slave In SPI data received by the 33889. 27 CS Input Chip Select The CSLOW input pin is used with the SPI bus to select the 33889. When the CSLOW is asserted LOW, the 33889 is the selected device of the SPI bus. 28 WDOG Output Watchdog The WDOG output pin is asserted LOW if the software watchdog is not correctly triggered. 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 5 ELECTRICAL CHARACTERISTICS MAXIMUM RATINGS ELECTRICAL CHARACTERISTICS MAXIMUM RATINGS Table 3. Maximum Ratings All voltages are with respect to ground unless otherwise noted. Exceeding these ratings may cause a malfunction or permanent damage to the device. Ratings Symbol Max Unit ELECTRICAL RATINGS Supply Voltage at VSUP Continuous voltage V VSUP Transient voltage (Load dump) Logic Signals (RX, TX, MOSI, MISO, CS, SCLK, RST, WDOG, INT) -0.3 to 27 40 VLOG -0.3 to VDD1 +0.3 V I Internally Limited mA Voltage V I -0.2 to VSUP +0.3 Internally Limited V Output Current Output current VDD1 HS1 A L0, L1 DC Input voltage VWU -0.3 to 40 V DC Input current IWU -2.0 to 2.0 mA VTRWU +-100 V DC voltage at V2 (V2INT) V2INT 0 to 5.25 V DC Voltage On Pins CANH, CANL VBUS -20 to +27 V VCANH/VCANL -40 to +40 V VTR -150 to +100 V VRTL, VRTH -0.3 to +27V V VRTH/VRTL -0.3 to +40 V Transient input voltage (according to ISO7637 specification) and with external component per Figure 3. Transient Voltage At Pins CANH, CANL 0.0 < V2-INT < 5.5 V; VSUP = 0.0; T < 500 ms Transient Voltage On Pins CANH, CANL (Coupled Through 1.0 nF Capacitor) DC Voltage On Pins RTH, RTL Transient Voltage At Pins RTH, RTL 0.0 < V2-INT < 5.5 V; VSUP = 0.0; T < 500 ms 33889 6 Analog Integrated Circuit Device Data Freescale Semiconductor ELECTRICAL CHARACTERISTICS MAXIMUM RATINGS Table 3. Maximum Ratings (continued) All voltages are with respect to ground unless otherwise noted. Exceeding these ratings may cause a malfunction or permanent damage to the device. Ratings Symbol ESD voltage (HBM 100 pF, 1.5 k) (3) Max VESDH kV CANL, CANH, HS1, L0, L1 ±4.0 RTH, RTL ±3.0 All other pins ±2.0 ESD voltage (Machine Model) All pins, MC33889B (3) (4) VESD-MM ESD voltage (CDM) All pins, MC33889D (4) VESD-CDM ±200 V V Pins 1,14,15, & 28 750 All other pins 500 RTH, RTL Termination Resistance Unit RT 500 to 16000 ohms Junction Temperature TJ -40 to 150 °C Storage Temperature TS -55 to 165 °C Ambient Temperature (for info only) TA -40 to 125 °C RTHJ/P 20 °C/W THERMAL RATINGS Thermal resistance junction to gnd pin (5) Notes: 3. Testing done in accordance with the Human Body Model (CZAP=100 pF, RZAP=1500 ), Machine Model (CZAP=200 pF, RZAP=0 ). 4. ESD machine model (MM) is for MC33889B only. MM is now replaced by CDM (Charged Discharged model). 5. Gnd pins 6,7,8,9,20, 21, 22, 23. 1nF LX Transient Pulse Generator (note) 10 k Gnd Gnd Note: Waveform in accordance to ISO7637 part1, test pulses 1, 2, 3a and 3b. Figure 3. Transient test pulse for L0 and L1 inputs 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 7 ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 4. Static Electrical Characteristics . Characteristics noted under conditions - VSUP From 5.5 V to 18 V and TJ from -40°C to 125°C, unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25°C under nominal conditions unless otherwise noted. Description Symbol Min Typ Max Unit VSUP 5.5 - 18 V VSUP-EX1 4.5 - 5.5 V Extended DC Voltage range 2 (8) VSUP-EX2 18 - 27 V Input Voltage during Load Dump VSUPLD - - 40 V VSUPJS - - 27 V ISUP - 95 130 µA - 55 90 µA - 170 270 µA ISUP(STDBY) - 42 45 mA ISUP(NORM) - 42.5 45 mA ISUP - 120 150 µA - 80 110 µA - 200 285 µA INPUT PIN (VSUP) Nominal DC Voltage range Extended DC Voltage range 1 Reduced functionality (6) Load dump situation Input Voltage during jump start Jump start situation Supply Current in Sleep Mode (7) VDD1 & V2 off, VSUP ≤ 12 V, oscillator running (10) (SLEEP1) VDD1 & V2 off, VSUP ≤ 12 V, oscillator not running (SLEEP2) Supply Current in Sleep Mode (7) ISUP Supply current in sleep mode (7) ISUP VDD1 & V2 off, VSUP = 18 V, oscillator running (10) Supply Current in Stand-by Mode (7),(9) (SLEEP3) Iout at VDD1 = 40 mA, CAN recessive state or disabled Supply Current in Normal Mode (7) Iout at VDD1 = 40 mA, CAN recessive state or disabled Supply Current in Stop mode (7),(9) I out VDD1 < 2.0 mA, VDD1 on (11), VSUP ≤ 12 V, oscillator (STOP1) running (10) Supply Current in Stop mode (7),(9) ISUP VSUP ≤ 12V, oscillator (STOP2) Iout VDD1 < 2.0 mA, VDD1 on (11), VSUP = 18 V, oscillator (STOP3) Iout VDD1 < 2.0 mA, VDD1 on (11) not running (10) Supply Current in Stop mode (7),(9) ISUP running (10) Notes 6. VDD1 > 4.0 V, reset high, if RSTTH-2 selected and IOUT VDD1 reduced, logic pin high level reduced, device is functional. 7. Current measured at VSUP pin. 8. Device is fully functional. All modes available and operating, Watchdog, HS1 turn ON turn OFF, CAN cell operating, L0 and L1 inputs operating, SPI read write operation. Over temperature may occur. Measured in worst case condition with 5.0 V at V2 pin (V2 pin tied to VDD1). Oscillator running means “Forced Wake-Up” or “Cyclic Sense” or “Software Watchdog” timer activated. Software Watchdog is available in stop mode only. VDD1 is ON with 2.0 mA typical output current capability. 9. 10. 11. 33889 8 Analog Integrated Circuit Device Data Freescale Semiconductor ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 4. Static Electrical Characteristics (continued). Characteristics noted under conditions - VSUP From 5.5 V to 18 V and TJ from -40°C to 125°C, unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25°C under nominal conditions unless otherwise noted. Description Symbol Min Typ Max Unit Supply Fail Flag internal threshold VTHRESH 1.5 3.0 4.0 V Supply Fail Flag hysteresis (12) VDETHYST - 1.0 - V BFEW 5.8 6.1 6.4 V BFEWH 0.1 0.2 0.3 V Battery fall early warning threshold In normal & standby mode Battery fall early warning hysteresis In normal & standby mode (12) OUTPUT PIN (VDD1) (13) VDD1 Output Voltage VDD1OUT V IDD1 from 2.0 to 200mA 5.5 V < VSUP < 27 V 4.5 V < VSUP < 5.5 V 4.9 4.0 5.0 - 5.1 - VDD1DROP - 0.2 0.5 V VDD1DP2 - 0.1 0.25 V IDD1 200 270 350 mA VDDSTOP 4.75 5.00 5.25 V IDD1S-WU1 2.0 3.5 6.0 mA IDD1 stop output current to wake-up SBC (14) IDD1S-WU2 10 14 18 mA IDD1 over current wake deglitcher IDD1-DGIT11 40 55 75 µs IDD1-DGIT2 - 150 - µs TSD 160 - 190 °C TPW 130 - 160 °C TSD-TPW 20 - 40 °C Drop Voltage VSUP > VDDOUT IDD1 = 200 mA Drop Voltage VSUP > VDDOUT, limited output current IDD1 = 50 mA 4.5 V < VSUP < 27 V IDD1 Output Current Internally limited VDD1 Output Voltage in stop mode Iout < 2.0 mA IDD1 stop output current to wake-up SBC Default value after reset. (14) (with IDD1S-WU1 selected) (12) IDD1 over current wake deglitcher (with IDD1S-WU2 selected) (12) Thermal Shutdown Normal or standby mode Over temperature pre warning VDDTEMP bit set Temperature Threshold difference Notes 12. Guaranteed by design 13. IDD1 is the total regulator output current. VDD specification with external capacitor C ≥ 22µF and ESR < 1O ohm. 14. Selectable by SPI 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 9 ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 4. Static Electrical Characteristics (continued). Characteristics noted under conditions - VSUP From 5.5 V to 18 V and TJ from -40°C to 125°C, unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25°C under nominal conditions unless otherwise noted. Description Symbol Min Typ Max Unit VRST-TH1 4.5 4.6 4.7 V VRST-TH2 4.1 4.2 4.3 V RESET-DUR 0.85 1.0 2.0 ms VDD 1.0 - - V tD 5.0 - 20 µs LR1 - 5.0 25 mV LR2 - 10 25 mV LD - 25 75 mV THERMS - 5.0 - mV V2 0.99 1.0 1.01 VDD1 I2 200 - - mA V2 CTRL sink current capability I2CTRL 10 - - mA V2LOW flag threshold V2LTH 3.75 4.0 4.25 V Internal V2 Supply Current (CAN and SBC in Normal Mode). TX = 5.0 V, CAN in Recessive State IV2RS 3.8 5.6 6.8 mA Internal V2 Supply Current (CAN and SBC in Normal Mode). TX = 0.0 V, No Load, CAN in Dominant State IV2DS 4.0 5.8 7.0 mA Internal V2 Supply Current (CAN in Receive Only Mode, SBC in Normal mode). VSUP = 12 V IV2R 80 120 µA Internal V2 Supply Current (CAN in Bus TermVbat mode, SBC in normal mode), VSUP = 12 V IV2BT 35 60 µA Reset threshold 1 Default value after reset. (15) Reset threshold 2 (15) Reset duration VDD1 range for Reset Active Reset Delay Time Measured at 50% of reset signal. (16) Line Regulation 9.0 V < VSUP < 18, IDD = 10 mA Line Regulation 5.5 V < VSUP < 27 V, IDD = 10 mA Load Regulation 1 mA < IIDD < 200 mA Thermal stability VSUP = 13.5 V, I = 100 mA V2 REGULATOR (V2) (17) V2 Output Voltage I2 from 2.0 to 200 mA 5.5 V < VSUP < 27 V I2 output current (for information only) Depending on the external ballast transistor Notes 15. Selectable by SPI 16. Guaranteed by design 17. V2 TRACKING VOLTAGE REGULATOR - V2 specification with external capacitor - option 1: C ≥ 22 µF and ESR < 10 ohm. Using a resistor of 2 kohm or less between the base and emitter of the external PNP is recommended. - option2: 1.0 µF < C < 22 µF and ESR < 10 ohm. In this case depending on the ballast transistor gain an additional resistor and capacitor network between emitter and base of PNP ballast transistor might be required. Refer to Freescale application information or contact your local technical support. - option 3: 10uF < C < 22uF ESR > 0.2 ohms: a resistor of 2 kohm or less is required between the base and emitter of the external PNP. 33889 10 Analog Integrated Circuit Device Data Freescale Semiconductor ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 4. Static Electrical Characteristics (continued). Characteristics noted under conditions - VSUP From 5.5 V to 18 V and TJ from -40°C to 125°C, unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25°C under nominal conditions unless otherwise noted. Description Symbol Min Typ Max Unit VOL - - 1.0 V VOH VDD1-0.9 - - V IHZ -2.0 - +2.0 µA High Level Input Voltage VIH 0.7VDD1 - VDD1+0.3V Low Level Input Voltage VIL -0.3 - 0.3 VDD1 V -100 - -20 µA IIL -100 - -20 µA IIN -10 - 10 µA IOH -350 -250 -150 µA 5.5 v < VSUP < 27 V 0.0 - 0.9 1.0 V < VDD1 0.0 - 0.9 IPDW 2.3 - 5.0 mA VOL 0.0 - 0.9 V VOH VDD1 -0.9 - VDD1 V Low Level Output Voltage (I0 = 1.5 mA) VOL 0.0 - 0.9 V High Level Output Voltage (I0 = -250 µA) VOH VDD1 -0.9 - VDD1 V RDSON25 - - 2.5 Ohms LOGIC OUTPUT PINS (MISO) Low Level Output Voltage IOUT = 1.5 mA High Level Output Voltage IOUT = -250 µA Tri-state MISO Leakage Current 0.0 V < Vmiso < VDD LOGIC INPUT PINS (MOSI, SCLK, CS) Input Current on CS VI = 4.0 V VI = 1.0 V Low Level Input Current CS IIH IIL VI = 1.0 V MOSI, SCLK Input Current 0.0 < VIN < VDD RESET PIN (RST) High Level Output current 0.0 < Vout < 0.7 VDD Low Level Output Voltage (I0 = 1.5 mA) Reset pull down current VOL V WATCHDOG PIN (WDOG) Low Level Output Voltage (I0 = 1.5 mA) 5.5 V < VSUP < 27 V High Level Output Voltage (I0 = -250 µA) INTERRUPT PIN (INT) HIGH-SIDE OUTPUT PIN (HS1) RDSON at Tj = 25°C, and IOUT -150 mA VSUP>9V 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 11 ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 4. Static Electrical Characteristics (continued). Characteristics noted under conditions - VSUP From 5.5 V to 18 V and TJ from -40°C to 125°C, unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25°C under nominal conditions unless otherwise noted. Description Symbol Min Typ Max Unit RDSON125 - - 5.0 Ohms RDON125-2 - 4.0 5.5 Ohms Output current limitation ILIM 160 - 500 mA Over temperature Shutdown OVT 155 - 190 °C ILEAK - - 10 µA VCL -1.5 - -0.3 V 5.5 V < VSUP < 6.0 V 1.7 2.0 3.0 6.0 V < VSUP < 18 V 2.0 2.4 3.0 18 V < VSUP < 27 V 2.0 2.5 3.1 RDSON at Tj = 125°C, and IOUT -150 mA VSUP > 9.0 V RDSON at Tj = 125°C, and IOUT -120 mA 5.5 V < VSUP < 9.0 V Leakage current Output Clamp Voltage at IOUT = -1.0 mA (18) no inductive load drive capability INPUT PINS (L0 AND L1) L0 Negative Switching Threshold L0 Positive Switching Threshold VTH0N V VTH0P V 5.5 V < VSUP < 6.0 V 2.2 2.75 4.0 6.0 V < VSUP < 18 V 2.5 3.4 4.0 18 V < VSUP < 27 V 2.5 3.5 4.1 L1 Negative Switching Threshold VTH1N V 5.5 V < VSUP < 6.0 V 2.0 2.5 3.0 6.0 V < VSUP < 18 V 2.5 3.0 3.7 18 V < VSUP < 27 V 2.7 3.2 3.8 L1 Positive Switching Threshold VTH1P V 5.5 V < VSUP < 6.0 V 2.7 3.3 3.8 6.0 V < VSUP < 18V 3.0 4.0 4.7 18 V < VSUP < 27 V 3.5 4.2 4.8 VHYST 0.6 1.0 1.3 V IIN -10 - 10 µA Hysteresis 5.5 V < VSUP < 27 V Input current -0.2 V < VIN < 40 V CAN MODULE SPECIFICATION (TX, RX, CANH, CANL, RTH, AND RTL) DC Voltage On Pins TX, RX VLOGIC -0.3 VDD1 + 0.3 V DC voltage at V2 (V2INT) V2INT 0.0 5.25 V DC Voltage On Pins CANH, CANL VBUS -20 +27 V Notes 18. Refer to HS1 negative maximum rating voltage limitation of -0.2V. 33889 12 Analog Integrated Circuit Device Data Freescale Semiconductor ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 4. Static Electrical Characteristics (continued). Characteristics noted under conditions - VSUP From 5.5 V to 18 V and TJ from -40°C to 125°C, unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25°C under nominal conditions unless otherwise noted. Description Max Unit -40 40 V VTR -150 100 V Detection Threshold For Short-circuit To Battery Voltage (Term VBAT Mode) MC33889B VCANH VSUP/2+3 VSUP/2+5 V Detection Threshold For Short-circuit To Battery Voltage (Term VBAT Mode) MC33889D VCANH VSUP/2+3 VSUP/ 2+4.55 V DC Voltage On Pins RTH, RTL VRTL, VRTH -0.3 +27 V Transient Voltage At Pins RTH, RTL VRTH/VRTL -0.3 40 V High Level Input Voltage VIH 0.7*V2 V2+0.3V V Low Level Input Voltage VIL -0.3 0.3 * V2 V TX High Level Input Current (VI = 4.0 V) ITXH -100 -50 -25 µA TX Low Level Input Current (VI = 1.0 V) ITXL -100 -50 -25 µA High Level Output Voltage RX (I0 = -250 µA) VOH V2-INT - 0.9 V2-INT V Low Level Output Voltage (I0 = 1.5 mA) VOL 0.0 0.9 V Transient Voltage At Pins CANH, CANL Symbol Min VCANH/VCANL Typ 0.0 < V2-INT < 5.5 V; VSUP ≥ 0.0; T < 500 ms Transient Voltage On Pins CANH, CANL (Coupled Through 1.0 nF Capacitor) 0.0 < V2-INT < 5.5 V; VSUP ≥ 0.0; T < 500 ms TRANSMITTER DATA PIN (TX) RECEIVE DATA PIN (RX) CAN HIGH AND CAN LOW PINS (CANH, CANL) Differential Receiver, Recessive To Dominant Threshold VDIFF1 V (By Definition, VDIFF = VCANH-VCANL) For 33889D -3.5 -3.0 -2.5 For 33889B -3.2 -2.6 -2.1 Differential Receiver, Dominant To Recessive Threshold (Bus Failures 1, 2, 5) VDIFF2 For 33889D For 33889B CANH Recessive Output Voltage V -3.5 -3.0 -2.5 -3.2 -2.6 -2.1 VCANH 0.2 V TX = 5.0 V; R(RTH) < 4.0 k CANL Recessive Output Voltage VCANL V2-INT - 0.2 V TX = 5.0 V; R(RTL) < 4.0 k 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 13 ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 4. Static Electrical Characteristics (continued). Characteristics noted under conditions - VSUP From 5.5 V to 18 V and TJ from -40°C to 125°C, unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25°C under nominal conditions unless otherwise noted. Description CANH Output Voltage, Dominant Symbol Min VCANH V2 - 1.4 Typ Max Unit V TX = 0.0 V; ICANH = -40 mA; Normal Operating Mode (19) CANL Output Voltage, Dominant VCANL 1.4 V TX = 0.0 V; ICANL = 40 mA; Normal Operating Mode (19) CANH Output Current (VCANH = 0; TX = 0.0) ICANH mA For 33889D 50 100 130 For 33889B 50 75 110 For 33889D 50 140 170 For 33889B 50 90 135 7.9 8.9 V CANL Output Current (VCANL = 14 V; TX = 0.0) ICANL mA Detection Threshold For Short-circuit To Battery Voltage (Normal Mode) VCANH, VCANL 7.3 Detection Threshold For Short-circuit To Battery Voltage (Term VBAT Mode), MC33889B VcanH Vsup/2+3 Vsup/2+5 V Detection Threshold For Short-circuit To Battery Voltage (Term VBAT Mode), MC33889D VcanH Vsup/2+3 Vsup/ 2+4.55 V CANH Output Current (Term VBAT Mode; VCANH = 12 V, Failure3) ICANH 5.0 10 µA CANL Output Current (Term VBAT Mode; VCANL = 0.0 V; ICANL 0.0 2.0 µA VBAT = 12 V, Failure 4) CANL Wake-Up Voltage Threshold VWAKE,L 2.5 3.0 3.9 V CANH Wake-Up Voltage Threshold VWAKE,H 1.2 2.0 2.7 V Wake-Up Threshold Difference (Hysteresis) VWAKELVWAKEH 0.2 CANH Single Ended Receiver Threshold (Failures 4, 6, 7) VSE, CANH 1.5 1.85 2.15 V CANL Single Ended Receiver Threshold (Failures 3, 8) VSE, CANL 2.8 3.05 3.4 V CANL Pull Up Current (Normal Mode) ICANL,PU 45 75 90 µA CANH Pull Down Current (Normal Mode) ICANH,PD 45 75 90 µA RDIFF 100 300 kohm VCOM -10 10 V Receiver Differential Input Impedance CANH / CANL Differential Receiver Common Mode Voltage Range (20) V CANH To Ground Capacitance CCANH 50 pF CANL To Ground Capacitance CCANL 50 pF CCANL to CCANH Capacitor Difference DCCAN 10 pF CAN Driver Thermal Shutdown tCSD 150 160 °C Notes 19. For MC33889B, after 128 pulses on TX and no bus failure. 20. Guaranteed by design 33889 14 Analog Integrated Circuit Device Data Freescale Semiconductor ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 4. Static Electrical Characteristics (continued). Characteristics noted under conditions - VSUP From 5.5 V to 18 V and TJ from -40°C to 125°C, unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25°C under nominal conditions unless otherwise noted. Description Symbol Min Typ Max Unit RRTL 10 30 90 ohms RTL to BAT Switch Series Resistance (term VBAT Mode) RRTL 8.0 12.5 20 kohm RTH To Ground Switch On Resistance (IOUT < 10 mA; Normal Operating Mode) RRTH 10 30 90 ohm BUS TERMINATION PINS (RTH, RTL) RTL to V2 Switch On Resistance (IOUT < -10 mA; Normal Operating Mode) 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 15 ELECTRICAL CHARACTERISTICS DYNAMIC ELECTRICAL CHARACTERISTICS DYNAMIC ELECTRICAL CHARACTERISTICS Table 5. Dynamic Electrical Characteristics VSUP From 5.5 V to 18 V, V2INT from 4.75 to 5.25 V and TJ from -40°C to 150°C unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25°C under nominal conditions unless otherwise noted. Conditions Symbol Min Typ Max Unit SPI operation frequency FREQ - - 4.0 MHz SCLK Clock Period tPCLK 250 - - ns SCLK Clock High Time tWSCLKH 125 - - ns SCLK Clock Low Time tWSCLKL 125 - - ns tlLEAD 100 50 - ns Falling Edge of SCLK to Rising Edge of CS tLAG 100 50 - ns MOSI to Falling Edge of SCLK tSISU 40 25 - ns Falling Edge of SCLK to MOSI tSIH 40 25 - ns MISO Rise Time (CL = 220 pF) tRSO - 25 50 ns MISO Fall Time (CL = 220 pF) tfSO - 25 50 ns - - DIGITAL INTERFACE TIMING (SCLK, CS, MOSI, MISO) Falling Edge of CS to Rising Edge of SCLK Time from Falling or Rising Edges of CS to: ns - MISO Low Impedance tSOEN 50 - MISO High Impedance tSODIS 50 Time from Rising Edge of SCLK to MISO Data Valid tVALID - - 50 ns TCS-STOP 18 - 34 µs TINT 7.0 10 13 µs OSC-F1 - 100 - kHz 0.2 V1 ≤ SO ≥ 0.8 V1, CL = 200 pF Delay between CS low to high transition (at end of SPI stop command) and Stop or sleep mode activation (21) detected by V2 off Interrupt low level duration SBC in stop mode Internal oscillator frequency All modes except Sleep and Stop (21) Notes 21. Guaranteed by design 33889 16 Analog Integrated Circuit Device Data Freescale Semiconductor ELECTRICAL CHARACTERISTICS DYNAMIC ELECTRICAL CHARACTERISTICS Table 5. Dynamic Electrical Characteristics (continued) VSUP From 5.5 V to 18 V, V2INT from 4.75 to 5.25 V and TJ from -40°C to 150°C unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25°C under nominal conditions unless otherwise noted. Conditions Internal low power oscillator frequency Sleep and Stop modes Symbol Min Typ Max Unit OSC-F2 - 100 - kHz WD1 8.58 9.75 10.92 ms WD2 39.6 45 50.4 ms WD3 88 100 112 ms WD4 308 350 392 ms F1ACC -12 - 12 % NRTOUT 308 350 392 ms WD1STOP 6.82 9.75 12.7 ms WD2STOP 31.5 45 58.5 ms WD3STOP 70 100 130 ms WD4STOP 245 350 455 ms F2ACC -30 - 30 % CSFWU1 3.22 4.6 5.98 ms CSFWU2 6.47 9.25 12 ms (22) Watchdog period 1 Normal and standby modes Watchdog period 2 Normal and standby modes Watchdog period 3 Normal and standby modes Watchdog period 4 Normal and standby modes Watchdog period accuracy Normal and standby modes Normal request mode timeout Normal request mode Watchdog period 1 - stop Stop mode Watchdog period 2- stop Stop mode Watchdog period 3 - stop Stop mode Watchdog period 4 - stop Stop mode Stop mode watchdog period accuracy Stop mode Cyclic sense/FWU timing 1 Sleep and stop modes Cyclic sense/FWU timing 2 Sleep and stop modes Notes 22. Guaranteed by design 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 17 ELECTRICAL CHARACTERISTICS DYNAMIC ELECTRICAL CHARACTERISTICS Table 5. Dynamic Electrical Characteristics (continued) VSUP From 5.5 V to 18 V, V2INT from 4.75 to 5.25 V and TJ from -40°C to 150°C unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25°C under nominal conditions unless otherwise noted. Conditions Cyclic sense/FWU timing 3 Symbol Min Typ Max Unit CSFWU3 12.9 18.5 24 ms CSFWU4 25.9 37 48.1 ms CSFWU5 51.8 74 96.2 ms CSFWU6 66.8 95.5 124 ms CSFWU7 134 191 248 ms CSFWU8 271 388 504 ms tON 200 300 400 µs tACC -30 - +30 % tS-HSON - - 22 µs tS-HSOFF - - 22 µs tS-V2ON 9.0 - 25 µs tS-V2OFF 9.0 - 25 µs tS-NR2N 15 35 70 µs Sleep and stop modes Cyclic sense/FWU timing 4 Sleep and stop modes Cyclic sense/FWU timing 5 Sleep and stop modes Cyclic sense/FWU timing 6 Sleep and stop modes Cyclic sense/FWU timing 7 Sleep and stop modes Cyclic sense/FWU timing 8 Sleep and stop modes Cyclic sense On time in sleep and stop modes Cyclic sense/FWU timing accuracy in sleep and stop mode Delay between SPI command and HS1 turn on (23) Normal or standby mode, VSUP > 9.0 V Delay between SPI command and HS1 turn off (23) Normal or standby mode, VSUP > 9.0 V Delay between SPI and V2 turn on (23) Standby mode Delay between SPI and V2 turn off (23) Normal modes Delay between Normal Request and Normal mode, after W/D trigger command Normal request mode Notes 23. State Machine Timing - Delay starts at rising edge of CS (end of SPI command) and start of Turn on or Turn off of HS1 or V2. 33889 18 Analog Integrated Circuit Device Data Freescale Semiconductor ELECTRICAL CHARACTERISTICS DYNAMIC ELECTRICAL CHARACTERISTICS Table 5. Dynamic Electrical Characteristics (continued) VSUP From 5.5 V to 18 V, V2INT from 4.75 to 5.25 V and TJ from -40°C to 150°C unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25°C under nominal conditions unless otherwise noted. Conditions Delay between SPI and “CAN normal mode” SBC Normal mode Min Typ Max Unit tS-CANN - - 10 µs tS-CANS - - 10 µs tW-CS 15 40 90 µs tW-SPI 90 - - µs tS-1STSPI 20 - - µs (24) Delay between SPI and “CAN sleep mode” SBC Normal mode Symbol (24) Delay between CS wake-up (CS low to high) and SBC normal request mode (VDD1 on & reset high) SBC in stop mode Delay between CS wake-up (CS low to high) and first accepted SPI command SBC in stop mode Delay between INT pulse and 1st SPI command accepted In stop mode after wake-up Delay between two SPI messages addressing the same register µs t2SPI For 33889D only 25 - - 8.0 20 38 INPUT PINS (L0 AND L1) Wake-up Filter Time (enable/disable option on L0 input) tWUF µs (If filter enabled) PIN AC CHARACTERISTICS (CANH, CANL, RX, TX) CANL and CANH Slew Rates (25% to 75% CAN signal). (25) tSLDR Recessive to Dominant state Dominant to Recessive state Propagation Delay TX to RX Low. -40°C < T ≤ 25°C. V/µs 2.0 2.0 8.0 9.0 µs tONRX (26) TX to RX Low. 25°C < T < 125°C. (26) Propagation Delay TX to RX High. (26) tOFFRX 1.2 1.6 1.1 1.8 1.8 2.2 µs Notes 24. Guaranteed by design 25. Dominant to recessive slew rate is dependant upon the bus load characteristics. 26. AC Characteristics measured according to schematic Figure 4 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 19 ELECTRICAL CHARACTERISTICS DYNAMIC ELECTRICAL CHARACTERISTICS Table 5. Dynamic Electrical Characteristics (continued) VSUP From 5.5 V to 18 V, V2INT from 4.75 to 5.25 V and TJ from -40°C to 150°C unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25°C under nominal conditions unless otherwise noted. Conditions Symbol Loop time Tx to Rx, no bus failure, MC33889D only ((27), Figure 5) (ISO ICT test series 10) tLOOPRD Min Tx low to high transition (recessive edge) Unit 1.5 1.45 1.5 µs Tx low to high transition (recessive edge) Min. Dominant Time For Wake-up On CANL or CANH 1.15 tLOOPRD-F Tx high to low transition (dominant edge) Loop time Tx to Rx, with bus failure and +-1.5V gnd shift, 5 nodes network, MC33889D,((28), Figure 7, ISO ICT tests series 11) Max µs Tx high to low transition (dominant edge) Loop time Tx to Rx, with bus failure, MC33889D only ((27), Figure 6) (ISO ICT test series 10) Typ - 1.9 - 1.9 tLOOPRD/DR-F+GS 3.6 µs µs tWAKE (Term Vbat; VSUP = 12V) Guaranteed by design. MC33889B 30 MC33889D 8.0 16 30 10 30 80 µs Failure 3 Detection Time (Normal Mode) tDF3 Failure 3 Recovery Time (Normal Mode) tDR3 Failure 6 Detection Time (Normal Mode) tDF6 50 200 500 µs Failure 6 Recovery Time (Normal Mode) tDR6 150 200 1000 µs Failure 4, 7 Detection Time (Normal Mode) tDF47 0.75 1.5 4.0 ms Failure 4, 7 Recovery Time (Normal Mode) tDR47 10 30 60 µs Failure 3a, 8 Detection Time (Normal Mode) tDF8 0.75 1.7 4.0 ms Failure 3a, 8 Recovery Time (Normal Mode) tTDR8 0.75 1.5 4.0 ms Failure 4, 7 Detection Time, (Term VBAT; VSUP = 12 V) tDR47 0.8 1.2 8.0 ms Failure 4, 7 Recovery Time (Term VBAT; VSUP = 12 V) tDR47 1.92 ms Failure 3 Detection Time (Term VBAT; VSUP = 12 V) tDR3 3.84 ms Failure 3 Recovery Time (Term VBAT; VSUP = 12 V) tDR3 1.92 ms Failure 3a, 8Detection Time (Term VBAT; VSUP = 12 V) tDR8 2.3 ms Failure 3a, 8 Recovery Time (Term VBAT; VSUP = 12 V) tDR8 1.2 ms µs 160 Notes 27. AC characteristic according to ISO11898-3, tested per figure 5 and 6. Guaranteed by design, room temperature only. 28. AC characteristic according to ISO11898-3, tested per figure 7. Max reported is the typical measurement under the worst condition (gnd shift, dominant/recessive edge, at source or destination node. ref to ISO test specification). Guaranteed by design, room temperature only. 33889 20 Analog Integrated Circuit Device Data Freescale Semiconductor ELECTRICAL CHARACTERISTICS DYNAMIC ELECTRICAL CHARACTERISTICS Table 5. Dynamic Electrical Characteristics (continued) VSUP From 5.5 V to 18 V, V2INT from 4.75 to 5.25 V and TJ from -40°C to 150°C unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25°C under nominal conditions unless otherwise noted. Conditions Symbol Min Typ Max Unit Edge Count Difference Between CANH and CANL for Failures 1, 2, 5 Detection (Failure bit set, Normal Mode) ECDF 3 Edge Count Difference Between CANH And CANL For Failures 1, 2, 5 Recovery (Normal Mode) ECDR 3 TX Permanent Dominant Timer Disable Time (Normal Mode And Failure Mode) tTX,D 0.75 4.0 ms TX Permanent Dominant Timer Enable Time (Normal Mode And Failure Mode) tTX,E 10 60 µs 5V VDD RtL R C Tx CANL C RcanL 1nF 500 RcanH 1nF 500 CANL MC33889D R = 100ohms C = 1nF Rx CANH CANH R RtH C RcanL = RcanH = 125 ohms Figure 4. Test Circuit for AC Characteristics Figure 5. ISO loop time without bus failure Vbat RtL Tx 500 CANL RcanH 1nF Failure Generator (*) CANH RtH 1nF Bus MC33889D Rx RcanL 500 RcanL = RcanH = 125 ohms except for failure CANH short to CANL (Rcanl = 1M ohms) (*) List of failure CANL short to gnd, Vdd, Vbat CANHshort to gnd, Vdd, Vbat CANL short to CANH CANL and CANH open Figure 6. ISO Loop Time with Bus Failure 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 21 ELECTRICAL CHARACTERISTICS DYNAMIC ELECTRICAL CHARACTERISTICS Figure 7. Test Set Up for Propagation Delay with GND Shift in a 5 Node Configuration 33889 22 Analog Integrated Circuit Device Data Freescale Semiconductor ELECTRICAL CHARACTERISTICS TIMING DIAGRAMS TIMING DIAGRAMS TX HIgh: RECESSIVE Bit TX High: RECESSIVE Bit VTX TX Low: DOMINANT Bit 5.0V CANL 3.6V 1.4V 0.0V CANH 2.2V VTH(DR) VDIFF VTH(RD) tOFFTX -5.0V VRX 0.7VCC 0.3VCC tONRX tOFFRX t RECESSIVE Bit DOMINANT Bit RECESSIVE Bit Figure 8. Device Signal Waveforms TPCLK CS TWCLKH TLEAD TLAG SCLK TWCLKL TSISU MOSI Undefined D0 TSIH Don’t Care D7 Don’t Care TVALID TSODIS TSOEN MISO D0 Don’t Care D7 Figure 9. Timing Characteristic 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 23 FUNCTIONAL DESCRIPTION INTRODUCTION FUNCTIONAL DESCRIPTION INTRODUCTION The MC33889 is an integrated circuit dedicated to automotive applications. It includes the following functions: • One full protected voltage regulator with 200 mA total output current capability. • Driver for external path transistor for V2 regulator function. • Reset, programmable watchdog function • Four operational modes • Wake-up capabilities: Forced wake-up, cyclic sense and wake-up inputs, CAN and the SPI • Can low speed fault tolerant physical interface. FUNCTIONAL PIN DESCRIPTION RECEIVE AND TRANSMIT DATA (RX AND TX) The RX and TX pins (receive data and transmit data pins, respectively) are connected to a microcontroller’s CAN protocol handler. TX is an input and controls the CANH and CANL line state (dominant when TX is LOW, recessive when TX is HIGH). RX is an output and reports the bus state (RX LOW when CAN bus is dominant, HIGH when CAN bus is recessive). VOLTAGE REGULATOR ONE (VDD1) The VDD1 pin is the output pin of the 5.0 V internal regulator. It can deliver up to 200 mA. This output is protected against overcurrent and overtemperature. It includes an overtemperature pre-warning flag, which is set when the internal regulator temperature exceeds 130°C typical. When the temperature exceeds the overtemperature shutdown (170°C typical), the regulator is turned off. VDD1 includes an undervoltage reset circuitry, which sets the RST pin LOW when VDD is below the undervoltage reset threshold. RESET (RST) The Reset pin RST is an output that is set LOW when the device is in reset mode. The RST pin is set HIGH when the device is not in reset mode. RST includes an internal pullup current source. When RST is LOW, the sink current capability is limited, allowing RST to be shorted to 5.0 V for software debug or software download purposes. VOLTAGE SUPPLY (VSUP) The VSUP pin is the battery supply input of the device. HIGH-SIDE OUTPUT 1 (HS1) The HS pin is the internal high-side driver output. It is internally protected against overcurrent and overtemperature. LEVEL 0-1 INPUTS (L0: L1) The L0: L1 pins can be connected to contact switches or the output of other ICs for external inputs. The input states can be read by the SPI. These inputs can be used as wakeup events for the SBC when operating in the Sleep or Stop mode. VOLTAGE REGULATOR TWO (V2) The V2 pin is the input sense for the V2 regulator. It is connected to the external series pass transistor. V2 is also the 5.0 V supply of the internal CAN interface. It is possible to connect V2 to an external 5.0 V regulator or to the VDD output when no external series pass transistor is used. In this case, the V2CTRL pin must be left open. RTH (RTH) Pin for the connection of the bus termination resistor to CANH INTERRUPT (INT) RTL (RTL) The Interrupt pin INT is an output that is set LOW when an interrupt occurs. INT is enabled using the Interrupt Register (INTR). When an interrupt occurs, INT stays LOW until the interrupt source is cleared. INT output also reports a wake-up event by a 10 sec. typical pulse when the device is in Stop mode. Pin for the connection of the bus termination resistor to CANL GROUND (GND) CAN HIGH AND CAN LOW OUTPUTS (CANH AND CANL) The CAN High and CAN Low pins are the interfaces to the CAN bus lines. They are controlled by TXD input level, and the state of CANH and CANL is reported through RXD output. This pin is the ground of the integrated circuit. SYSTEM CLOCK (SCLK) V2CTRL (V2CTRL) The V2CTRL pin is the output drive pin for the V2 regulator connected to the external series pass transistor. SCLK is the Serial Data Clock input pin of the serial peripheral interface. 33889 24 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DESCRIPTION FUNCTIONAL INTERNAL BLOCK DESCRIPTION MASTER IN/SLAVE OUT (MISO CHIP SELECT (CS) MISO is the Master In Slave Out pin of the serial peripheral interface. Data is sent from the SBC to the microcontroller through the MISO pin. CS is the Chip Select pin of the serial peripheral interface. When this pin is LOW, the SPI port of the device is selected. WATCH DOG (WDOG) MASTER OUT/SLAVE IN (MOSI) MOSI is the Master Out Slave In pin of the serial peripheral interface. Control data from a microcontroller is received through this pin. The Watchdog output pin is asserted LOW to flag that the software watchdog has not been properly triggered. FUNCTIONAL INTERNAL BLOCK DESCRIPTION DEVICE SUPPLY HS1 VBAT SWITCH OUTPUT The device is supplied from the battery line through the VSUP pin. An external diode is required to protect against negative transients and reverse battery. It can operate from 4.5 V and under the jump start condition at 27 V DC. This pin sustains standard automotive voltage conditions such as load dump at 40 V. When VSUP falls below 3.0 V typical, the MC33889 detects it and stores the information in the SPI register, in a bit called “BATFAIL”. This detection is available in all operation modes. HS1 output is a 2.0 ohm typical switch from the VSUP pin. It allows the supply of external switches and their associated pullup or pull-down circuitry, for example, in conjunction with the wake-up input pins. Output current is limited to 200 mA and HS1 is protected against short-circuit and has an over temperature shutdown (reported into the IOR register). The HS1 output is controlled from the internal register and the SPI. It can be activated at regular intervals in sleep mode thanks to an internal timer. It can also be permanently turned on in normal or stand-by modes to drive external loads, such as relays or supply peripheral components. In case of inductive load drive, external clamp circuitry must be added. VDD1 VOLTAGE REGULATOR VDD1 Regulator is a 5.0 V output voltage with total current capability of 200 mA. It includes a voltage monitoring circuitry associated with a reset function. The VDD1 regulator is fully protected against overcurrent, short-circuit and has overtemperature detection warning flags and shutdown with hysteresis. SPI The complete device control as well as the status report is done through an 8 bit SPI interface. Refer to the SPI paragraph. V2 REGULATOR CAN V2 Regulator circuitry is designed to drive an external path transistor in order to increase output current flexibility. Two pins are used: V2 and V2CTRL. Output voltage is 5.0 V and is realized by a tracking function of the VDD1 regulator. A recommended ballast transistor is the MJD32C. Other transistors might be used, however depending upon the PNP gain, an external resistor capacitor network might be connected between the emitter and base of the PNP. The use of external ballast is optional (refer to simplified typical application). The state of V2 is reported into the IOR register (if V2 is below 4.5 V typical, or in cases of overload or shortcircuit). The device incorporates a low speed fault tolerant CAN physical interface. The speed rate is up to 125 kBauds. The state of the CAN interface is programmable through the SPI. Reference the CAN transceiver description on page 30. PACKAGE AND THERMAL CONSIDERATION The device is proposed in a standard surface mount SO28 package. In order to improve the thermal performances of the SO28 package, 8 pins are internally connected to the lead frame and are used for heat transfer to the printed circuit board. 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 25 FUNCTIONAL DEVICE OPERATION OPERATIONAL MODES FUNCTIONAL DEVICE OPERATION OPERATIONAL MODES INTRODUCTION The device has four modes of operation, normal, stand-by, sleep and stop modes. All modes are controlled by the SPI. An additional temporary mode called “normal request mode” is automatically accessed by the device (refer to state machine) after wake-up events. Special mode and configurations are possible for software application debug and flash memory programming. NORMAL MODE In this mode both regulators are ON, and this corresponds to the normal application operation. All functions are available in this mode (watchdog, wake-up input reading through the SPI, HS1 activation, and CAN communication). The software watchdog is running and must be periodically cleared through the SPI. STANDBY MODE Only the Regulator 1 is ON. Regulator 2 is turned OFF by disabling the V2CTRL pin. The CAN cell is not available, as powered from V2. Other functions are available: wake-up input reading through the SPI and HS1 activation. The watchdog is running. SLEEP MODE Regulators 1 and 2 are OFF. In this mode, the MCU is not powered. The device can be awakened internally by cyclic sense via the wake-up input pins and HS1 output, from the forced wake function, the CAN physical interface, and the SPI (CS pin). STOP MODE Regulator 2 is turned OFF by disabling the V2CTRL pin. Regulator 1 is activated in a special low power mode which allows it to deliver 2.0 mA. The objective is to supply the MCU of the application while it is turned into a power saving condition (i.e stop or wait mode). Stop mode is entered through the SPI. Stop mode is dedicated to powering the Microcontroller when it is in low power mode (stop, pseudo stop, wait etc.). In these modes, the MCU supply current is less than 1.0 mA. The MCU can restart its software application very quickly without the complete power up and reset sequence. When the application is in stop mode (both MCU and SBC), the application can wake-up from the SBC side (ex cyclic sense, forced wake-up, CAN message, wake-up inputs) or the MCU side (key wake-up etc.). When Stop mode is selected by the SPI, stop mode becomes active 20 µs after end of the SPI message. The “go to stop” instruction must be the last instruction executed by the MCU before going to low power mode. In Stop mode, the Software watchdog can be “running” or “not running” depending on the selection by the SPI. Refer to the SPI description, RCR register bit WDSTOP. If the W/D is enabled, the SBC must wake-up before the W/D time has expired, otherwise a reset is generated. In stop mode, the SBC wake-up capability is identical as in sleep mode. STOP MODE: WAKE-UP FROM SBC SIDE, INT PIN ACTIVATION When an application is in stop mode, it can wake-up from the SBC side. When a wake-up is detected by the SBC (CAN, Wake-up input, forced wake-up, etc.), the SBC turns itself into Normal request mode and activates the VDD1 main regulator. When the main regulator is fully active, then the wake-up is signalled to the MCU through the INT pin. The INT pin is pulled low for 10 µs and then returns high. Wake-up events can be read through the SPI registers. STOP MODE: WAKE-UP FROM MCU SIDE When the application is in stop mode, the wake-up event may come to the MCU. In this case, the MCU has to signal to the SBC that it has to go into Normal mode in order for the VDD1 regulator to be able to deliver full current capability. This is done by a low to high transition of the CS pin. The CS pin low to high activation has to be done as soon as possible after the MCU. The SBC generates a pulse at the INT pin. Alternatively the L0 and L1 inputs can also be used as wakeup from the Stop mode. STOP MODE CURRENT MONITORING If the current in Stop mode exceeds the IDD1S-WU threshold, the SBC jumps into Normal request mode, activates the VDD1 main regulator, and generates an interrupt to the MCU. This interrupt is not maskable and a not bit are set into the INT register. SOFTWARE WATCHDOG IN STOP MODE If the watchdog is enabled (register MCR, bit WDSTOP set), the MCU has to wake-up independently of the SBC before the end of the SBC watchdog time. In order to do this, the MCU has to signal the wake-up to the SBC through the SPI wake-up (CS pin low to high transition to activated the SPI wake-up). Then the SBC wakes up and jumps into the normal request mode. The MCU has to configure the SBC to go to either into normal or standby mode. The MCU can then choose to go back into stop mode. If no MCU wake-up occurs within the watchdog timing, the SBC will activate the reset pin and jump into the normal request mode. The MCU can then be initialized. 33889 26 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION OPERATIONAL MODES NORMAL REQUEST MODE WAKE-UP CAPABILITIES This is a temporary mode automatically accessed by the device after a wake-up event from sleep or stop mode, or after device power up. In this mode, the VDD1 regulator is ON, V2 is off, and the reset pin is high. As soon as the device enters the normal request mode, an internal 350 ms timer is started. During these 350 ms, the microcontroller of the application must address the SBC via the SPI and configure the watchdog register (TIM1 register). This is the condition for the SBC to leave the Normal request Mode and enter the Normal mode, and to set the watchdog timer according to the configuration done during the Normal Request mode. The “BATFAIL flag” is a bit which is triggered when VSUP falls below 3.0 V. This bit is set into the MCR register. It is reset by the MCR register read. Several wake-up capabilities are available for the device when it is in sleep or stop mode. When a wake-up has occurred, the wake-up event is stored into the WUR or CAN registers. The MCU can then access the wake-up source. The wake-up options are selectable through the SPI while the device is in normal or standby mode, and prior to entering low power mode (sleep or stop mode). INTERNAL CLOCK This device has an internal clock used to generate all timings (reset, watchdog, cyclic wake-up, filtering time etc....). RESET PIN A reset output is available in order to reset the microcontroller. Reset causes are: • VDD1 falling out of range: if VDD1 falls below the reset threshold (parameter RST-TH), the reset pin is pulled low until VDD1 returns to the nominal voltage. • Power on reset: at device power on or at device wake-up from sleep mode, the reset is maintained low until VDD1 is within its operation range. • Watchdog timeout: if the watchdog is not cleared, the SBC will pull the reset pin low for the duration of the reset duration time (parameter: RESET-DUR). For debug purposes at 25°C, the reset pin can be shorted to 5.0 V. SOFTWARE WATCHDOG (SELECTABLE WINDOW OR TIMEOUT WATCHDOG) The software watchdog is used in the SBC normal and stand-by modes for monitoring the MCU. The watchdog can be either a window or timeout. This is selectable by the SPI (register TIM, bit WDW). Default is the window watchdog. The period of the watchdog is selectable by the SPI from 5.0 to 350 ms (register TIM, bits WDT0 and WDT1). When the window watchdog is selected, the closed window is the first half of the selected period, and the open window is the second half of the period. The watchdog can only be cleared within the open window time. An attempt to clear the watchdog in the closed window will generate a reset. The Watchdog is cleared through the SPI by addressing the TIM register. Refer to ”table for reset pin operations” operation in mode 2. WAKE-UP FROM WAKE-UP INPUTS (L0, L1) WITHOUT CYCLIC SENSE The wake-up lines are dedicated to sense external switch states, and when changes occur to wake-up the MCU (In sleep or stop modes). The wake-up pins are able to handle 40 V DC. The internal threshold is 3.0 V typical, and these inputs can be used as an input port expander. The wake-up inputs state can be read through the SPI (register WUR). L0 has a lower threshold than L1 in order to allow a connection and wake-up from a digital output such as a CAN physical interface. CYCLIC SENSE WAKE-UP (CYCLIC SENSE TIMER AND WAKE-UP INPUTS L0, L1) The SBC can wake-up from a state change of one of the wake-up input lines (L0, L1), while the external pullup or pulldown resistor of the switches associated to the wake-up input lines are biased with HS1 VSUP switch. The HS1 switch is activated in sleep or stop mode from an internal timer. Cyclic sense and forced wake-up are exclusive. If Cyclic sense is enabled, the forced wake-up can not be enabled. INFO FOR CYCLIC SENSE + DUAL EDGE SELECTION In case the Cyclic sense and Lx both level sensitive conditions are use together, the initial value for Lx inputs are sampled in two cases: 1) When the register LPC[D3 and D0] are set and 2) At cyclic sense event, that is when device is in sleep or stop mode and HS1 is active. The consequence is that when the device wake up by Lx transition, the new value is sampled as default, then when the device is set back into low power again, it will automatically wake up. The user should reset the LPC bits [D3 and D0] to 0 and set them again to the desired value prior to enter sleep or stop mode. FORCED WAKE-UP The SBC can wake-up automatically after a predetermined time spent in sleep or stop mode. Forced wake-up is enabled by setting bit FWU in the LPC register. Cyclic sense and forced wake-up are exclusive. If forced wake-up is enabled, the Cyclic sense can not be enabled. 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 27 FUNCTIONAL DEVICE OPERATION OPERATIONAL MODES CAN WAKE-UP BATTERY FALL EARLY WARNING The device can wake-up from a CAN message. A CAN wake-up cannot be disabled. This function provides an interrupt when the VSUP voltage is below the 6.1 V typical. This interrupt is maskable. A hysteresis is included. Operation is only in Normal and Stand-by modes. VBAT low state reports in the IOR register. SPI WAKE-UP The device can wake-up by the CS pin in sleep or stop mode. Wake-up is detected by the CS pin transition from a low to high level. In stop mode this correspond to the condition where the MCU and SBC are both in Stop mode, and when the application wake-up events come through the MCU. SYSTEM POWER UP At power up the device automatically wakes up. DEVICE POWER UP, SBC WAKE UP After device or system power up or a wake-up from sleep mode, the SBC enters into “reset mode” then into “normal request mode”. RESET AND WDOG OPERATION The following figure shows the reset and watchdog output operations. Reset is active at device power up and wake-up. Reset is activated in case the VDD1 falls or the watchdog is not triggered. The WDOG output is active low as soon as the reset goes low and stays low for as long as the watchdog is not properly re-activated by the SPI. The WDOG output pin is a push pull structure than can drive external components of the application, for instance to signal the MCU is in a wrong operation. Even if it is internally turned on (low-state), the reset pin can be forced to 5.0 V at 25°C only, thanks to its internally limited current drive capability. The WDOG stays low until the Watchdog register is properly addressed through the SPI. Watchdog timeout VDD1 RESET Watchdog period WDOG SPI W/D clear SPI CS Watchdog register addressed Figure 10. Reset and WDOG Function Diagram DEBUG MODE APPLICATION HARDWARE AND SOFTWARE DEBUG WITH THE SBC. When the SBC is mounted on the same printed circuit board as the micro controller, it supplies both application software and the SBC with a dedicated routine that must be debugged. The following features allow the user to debug the software by disabling the SBC internal software watchdog timer. DEVICE POWER UP, RESET PIN CONNECTED TO VDD1 At SBC power up, the VDD1 voltage is provided, but if no SPI communication occurs to configure the device, a reset occurs every 350 ms. In order to allow software debugging and avoid an MCU reset, the Reset pin can be connected directly to VDD1 by a jumper. DEBUG MODES WITH SOFTWARE WATCHDOG DISABLED THOUGH SPI (NORMAL DEBUG, STANDBY DEBUG AND STOP DEBUG) The software watchdog can be disabled through the SPI. In order to avoid unwanted watchdog disables, and to limit the risk of disabling the watchdog during an SBC normal operation, the watchdog disable has to be performed with the following sequence: Step 1) Power down the SBC Step 2) Power up the SBC (The BATFAIL bit is set, and the SBC enters normal request mode) Step 3) Write to the TIM1 register to allow the SBC to enter Normal mode Step 4) Write to the MCR register with data 0000 (this enables the debug mode). (Complete SPI byte: 000 1 0000) 33889 28 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION OPERATIONAL MODES Step 5) Write to the MCR register normal debug (0001 x101), stand-by debug (0001 x110), or Stop debug (0001 x111) While in debug mode, the SBC can be used without having to clear the W/D on a regular basis to facilitate software and hardware debugging. Step 6) To leave the debug mode, write 0000 to the MCR register. To avoid entering the debug mode after a power up, first read the BATFAIL bit (MCR read) and write 0000 into the MCR. Figure 11 illustrates entering the debug mode. VSUP VDD1 BATFAIL TIM1(step 3) MCR (step5) MCR (step6) SPI SPI: read batfail MCR(step4) debug mode SBC in debug Mode, no W/D SBC not in debug Mode and W/D on Figure 11. Debug Mode Enter MCU FLASH PROGRAMMING CONFIGURATION To facilitate the possibility of down loading software into the application memory (MCU EEPROM or Flash), the SBC allows the following capabilities: The VDD1 can be forced by an external power supply to 5.0 V and the reset and WDOG output by external signal sources to zero or 5.0 V without damage. This supplies the complete application board with external power supply and applies the correct signal to the reset pin. 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 29 FUNCTIONAL DEVICE OPERATION OPERATIONAL MODES CAN TRANSCEIVER DESCRIPTION Vsup V2 VSE-H (1.85V) IcanHpd SH CANH Driver CANL SL Stvbat VSE-L (3.05V) CANH SRL RTL RXD Rx multiplexer Vdiff RTH SRH V2 RtL RtH Failure detection IcanLpu TXD Tx driver SPI CAN mode control Driver Hwake CANL Lwake CANL V2 Vwake-H (2V) GND CANH Vwake-L (3V) Figure 12. Simplified Block Diagram of the CAN Transceiver of the MC33889 General description CAN driver: The CANH driver is a “high side” switch to the V2 voltage (5V). The CANL driver is a “low side” switch to gnd.The turn on and turn off time is controlled in order to control the slew rate, and the CANH and CANL driver have a current limitation as well as an over temperature shutdown. The CAN H or CANL driver can be disabled in case a failure is detected on the CAN bus (ex: CANH driver is disabled in case CANH is shorted to VDD). The disabling of one of the drivers is controlled by the CAN logic and the communication continues via the other drivers. When the failure is removed the logic detects a failure recovery and automatically reenables the associated driver. The CAN drivers are also disabled in case of a Tx failure detection. Bus termination: The bus is terminated by pull up and pull down resistors, which are connected to GND, VDD or VBAT through dedicated RTL and RTH pins and internal switches Srh, Srl, Stvbat. Each node must have a resistor connected between CANH and RTH and between CANL and RTL. The resistor value should be between 500 and 16000 ohms. Transmitter Function CAN bus levels are called Dominant and Recessive, and correspond respectively to Low and High states of the TX input pin. Dominant state: The CANH and CANL drivers are on. The voltage at CANL is <1.4V, the voltage at CANH is >3.6V, and the differential voltage between CANH and CANL line is >2.2V (3.6V-1.4V). Recessive state: This is a weak state, where the CANH and CANL drivers are off. The CANL line is pulled up to 5V via the RTL pin and RTL resistor, and the CANH line is pull down via the RTH and RTH resistor. The resultant voltage at CANL is 5V and 0V at CANH. The differential voltage is -5V (0V - 5V). The recessive state can be over written by any other node forcing a Dominant state. 33889 30 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION OPERATIONAL MODES Receiver Function In normal operation (no bus failures), RX is the image of the differential bus voltage. The differential receiver inputs are connected to CANH and CANL. The device incorporates single ended comparators connected to CANH and CANL in order to monitor the bus state as well as detect bus failures. Failures are reported via the SPI. In normal operation when no failure is present, the differential comparator is active. Under a fault condition, one of the two CANH or CANL pins can be become nonoperational. The single ended comparator of either CANH or CANL is activated and continues to report a bus state to Rx pin. The device permanently monitors the bus failure and recovery, and as soon as fault disappears, it automatically switches back to differential operation. CAN interface operation Mode The CAN has 3 operation modes: TxRx (TransmitReceive), Receive Only, and Term-VBAT (Terminated to VBAT). The mode is selected by the SPI. As soon as the MC33889 mode is sleep or stop (selected via MCR register), the CAN interface automatically enters Tem-Vbat mode. Tx Rx mode: In this mode, the CAN drivers and receivers are enabled, and the device is able to send and receive messages. Bus failures are detected and managed, this means that in case of a bus failure, one of the CAN drivers can be disabled, but communication continues via the remaining drivers. Receive Only mode: In this mode, the transmitter path is disabled, so the device does not drive the bus. It maintains CANL and CANH in the recessive state. The receiver function operates normally. TermVbat mode: RTL resistor and internal pull up resistor of 12.5kOhms. In this mode, the device monitors the bus activity and if a wake up conditions is encountered on the CAN bus, it will wakes up the MC33889. The device will enter into a normal request mode if low power mode was in sleep, or generates an INT. It enters into Normal request mode if low power mode was in stop mode. If the device was in normal or stand by mode, the Rx pin will report a wake up (feature not available on the MC33889B). See Rx pin behavior. Bus Failure Detection General description: The device permanently monitors the bus lines and detects faults in normal and receive only modes. When a fault is detected, the device automatically takes appropriate actions to minimize the system current consumption and to allow communication on the network. Depending on the type of fault, the mode of operation, and the fault detected, the device automatically switches off one or more of the following functions: CANL or CANH line driver, RTL or RTH termination resistors, or internal switches. These actions are detailed in the following table. The device permanently monitors the faults and in case of fault recovery, it automatically switches back to normal operation and reconnects the open functions. Fault detection and recovery circuitry have internal filters and delays timing, detailed in the AC characteristics parameters. The failure list identification and the consequence on the device operation are described in following table. The failure detection, and recovery principle, the transceiver state after a failure detected, timing for failure detection and recovery can be found in the ISO11898-3 standard. The following table is a summary of the failure identifications and of the consequences on the CAN driver and receiver when the CAN is in Tx Rx mode. In this mode, the transmitter and receiver functions are disabled. The CANL pin is connected to VSUP through the 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 31 FUNCTIONAL DEVICE OPERATION OPERATIONAL MODES Bus failure identification Description Consequence on CAN driver Consequence on Rx pin no failure default operation: CAN H and CANL driver active, RTH and RTL termination switched ON default operation: Report differential receiver output 1 CANH open wire default operation default operation 5 CANH shorted to gnd default operation default operation 8, 3a CANH shorted to Vdd (5V) CANH driver turn OFF. RTH termination switched OFF Rx report CANL single ended receiver 3 CANH shorted to Vbat CANH driver turn OFF. RTH termination switched OFF Rx report CANL single ended receiver 2 CANL open wire default operation default operation 4, 7 CANL shorted to gnd or CANL shorted to CANH CANL driver is OFF. RTL termination switched OFF Rx report CANH single ended receiver 9 CANL shorted to Vdd (5V) CANL driver is ON. RTL termination active default operation 6 CANL shorted to Vbat CANL driver is OFF. RTL termination switched OFF Rx report CANH single ended receiver Open wire detection operation: Description: The CANH and CANL open wire failures are not described in the ISO document. Open wire is only diagnostic information, as no CAN driver or receiver state will change in case of an open wire condition. In case one of the CAN wires are open, the communication will continue through the remaining wire. In this situation the MC33889 will receive information on one wire only and the consequences are as follows: when the bus is set in dominant: - The differential receiver will toggle - Only one of the single ended receivers CANH or of CANL will toggle The following figure illustrates the CAN signal during normal communication and in the example of a CANH open wire. The single ended receiver is sampled at the differential receiver switching event, in a window of 1µs. 33889 32 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION OPERATIONAL MODES (No open wire, or open wire recovery) Rec CANL Dom Rec (CAN H open wire) Rec CANL CANH Dom Rec CANH Sampling point Sampling point -3.2V Diff -3.2V Diff S-L S-L S-H S-H 1us Sampling dominant level = > no failure or “recovery pulse” Sampling recessive level = > open wire “detection pulse” Figure 13. CAN Normal Signal Communication and CAN Open Wire S-H 1us Sampling CANH Diff Dom Rec CANL S-L 1us Sampling CANH counter L-counter +/(count = 4) (count = 0) L-open recover Figure 14. Open Wire Detection Principle Open wire detection, MC33889B and D: Failure detection: The device will detect a difference in toggling counts between the differential receiver and one of the single ended receivers. Every time a difference in count is detected a counter is incremented. When the counter reaches 4, the device detects and reports an open wire condition. The open wire detection is performed only when the device receives a message and not when it send message. Open wire recovery: When the open wire failure has recovered, the difference in count is reduced and the device detects the open wire recovery. MC33889B: When detection is complete, the counter is no longer incremented. It can only be decremented by sampling of the dominant level on the S-H (S-L) (recovery pulse). When it reaches zero, the failure has recovered. 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 33 FUNCTIONAL DEVICE OPERATION OPERATIONAL MODES In application, with CAN communication, a recovery condition is detected after 4 acknowledge bits are sent by the MC33889B. MC33889D: When detection is complete, the counter is decremented by sampling the dominant pulse (recovery pulse) on S-H (SL), and incremented (up to 4) by sampling the recessive pulse (detection pulses) on S-H (S-L). It is necessary to get 4 consecutive dominant samples (recovery pulse) to get to zero. When reaching zero, the failure is recovered. In application with real CAN communication, a recovery condition will not be detected by a single acknowledge bit send by MC33889D, but requires a complete CAN message (at least 4 dominant bits) send in dual wire mode, without reception of any bit in single wire mode. permanent dominant bus state. If TX is low for more than 0.75-4ms, the bus output driver is disabled. This avoids blocking communication between other nodes of the network. TXD is reported via the SPI (RCR register bit D1: TXFAILURE). Tx permanent dominant recovery is done with TX recessive for more than typ 32us. Rx pin behavior while CAN interface is in TermVbat. The MC33889D is able to signal bus activity on Rx while the CAN interface is in TermVbat and the SBC in normal or standby mode. When the bus is driven into a dominant state by another sending node, each dominant state is reported at Rx by a low level, after a delay of TWAKE. The bus state report is done through the CAN interface wake up comparator on CANL and CANH, and thus operates also in case of bus failure. This is illustrated in the following figure. Tx permanent dominant detection: In addition to the previous list, the MC33889 detects a permanent low state at the TX input which results in a 33889 34 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION OPERATIONAL MODES Other CAN node send CANL terminated to Vbat Recessive state CANL Dominant state Dominant state Recessive state CANH Rx TWAKE TWAKE CAN in TermVbat CAN in TxRx MC33889D in Normal mode MC33889D in Normal mode, Standby mode or in stop mode CAN in TxRx MC33889D in Normal mode TWAKE: duration of the CAN wake up filter, typ 16µs. The MC33889D Rx dominant low level duration is the difference between the duration of the bus minus the Twake, as illustrated below (Trx_dom = Tbus_dom - Twake) Tx sender node Example: A dominant duration at the bus level of 5 bits of 8us each results in a 40us bus dominant. This results in a 24µs (40µs-16µs) dominant level at Rx of MC33889D (while the CAN of the MC33889D is in TermVbat). Dominant state Tx MC33889D Rx MC33889D TWAKE TRX_DOM TBUS_DOM Figure 15. Bus State Report of the CAN Interface Wake-Up Comparator on CANL and CANH 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 35 FUNCTIONAL DEVICE OPERATION OPERATIONAL MODES The following table summarizes the device behavior when a CAN Wake Up event occurs. Table 6. Summary of RX Pin Operations for Wake up Signaling SBC mode CAN state MC33889B MC33889D Normal TermVbat no event on RX, no bit set RX pulse (1), bit CANWU is not set Standby TermVbat no event on RX, no bit set RX pulse (1), bit CANWU is not set Sleep TermVbat SBC mode transition to Normal request, bit CANWU set SBC mode transition to Normal request, bit CANWU set Stop TermVbat INT pulse, bit CANWU set Int pulse, bit CANWU set Notes 29. pulse duration is bus dominant duration minus Twake. GND SHIFT DETECTION DETECTION PRINCIPLE GENERAL When normally working in two-wire operating mode, the CAN transmission can afford some ground shift between different nodes without trouble. Should a bus failure occur, the transceiver switches to single-wire operation, therefore working with less noise margin. The affordable ground shift is decreased. The SBC provides a ground shift detection for diagnosis purpose. The four ground shift levels are selectable and the detection is stored in the IOR register which is accessible via the SPI. Table 7. 33889 Table of Operations The table below describe the SBC operation modes. VOLTAGE REGULATOR HS1 SWITCH MODE Normal Request WAKE-UP CAPABILITIES (IF ENABLED) VDD1: ON The gnd shift to detect is selected via the SPI from 4 different values (-0.3 V, -0.7 V, -1.2 V, -1.7 V). At each TX falling edge (end of recessive state), the CANH voltage is sensed. If it is detected to be below the selected gnd shift threshold, the bit SHIFT is set at 1 in the IOR register. No filter is implemented. Required filtering for reliable detection should be done by software (e.g. several trials). DEVICE STATE DESCRIPTION RESET PIN SOFTWARE CAN CELL WATCHDOG INT Low for 1ms, then high V2: OFF term Vbat HS1: OFF Normal VDD1: ON V2: ON HS1 controllable Standby VDD1: ON V2: OFF HS1 controllable Stop VDD1: ON CAN (always enable) (limited current capability) Cyclic sense or V2: OFF Forced Wake-up SPI and L0,L1 Normally high. Active low if W/D or VDD1 under voltage occur If enabled, signal failure (VDD pre warning temp, CAN, HS1) Running Normally high. Active low if W/D or VDD1 under voltage occur If enabled, signal failure (VDD temp, HS1) Running Term Vbat Tx/Rx Rec only Normally high. Signal SBC - Running if Active low if W/D wake-up enabled or VDD1 under (not maskable) - Not Running voltage occur if disabled Term Vbat Tx/Rx Rec only Term Vbat. HS1: OFF or cyclic 33889 36 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION OPERATIONAL MODES Table 7. 33889 Table of Operations The table below describe the SBC operation modes. WAKE-UP CAPABILITIES (IF ENABLED) VOLTAGE REGULATOR HS1 SWITCH MODE Sleep RESET PIN VDD1: OFF CAN (always enable V2: OFF SPI and L0,L1 HS1 OFF or cyclic Cyclic sense SOFTWARE CAN CELL WATCHDOG INT Low Not active No Running Term Vbat. Forced Wake-up State Machine (not valid in debug modes) W/D: timeout OR VDD1 low W/D: timeout & Nostop & !BATFAIL Reset Normal Request to 4 O R w ot e2 ) r ge (n rig :T lo /D Power Down VD D1 SPI: normal ut SPI: standby eo Standby lo w im S hi PI: gh S tra top ns & iti CS on :t Wake-up /D 1 W SBC power up W 1 VDD1 low OR W/D: time out 350 ms & !Nostop SPI: standby & W/D trigger (note1) 3 2 1 Stop W/D: timeout OR VDD1 low SPI: Stop & CS low to high transition Nostop & SPI: sleep & CS low to high transition 2 Normal 1 Nostop & SPI: sleep & CS low to high transition Reset counter (1 ms) expired Wake-up (VDD1 high temperature OR (VDDd1 low > 100 ms & VSUP >BFew)) & Nostop & !BATFAIL 1 2 3 4 Sleep denotes priority State machine description: “Nostop” means Nostop bit = 1 “! Nostop” means Nostop bit = 0 “BATFAIL” means Batfail bit = 1 “! BATFAIL” means Batfail bit = 0 “VDD1 over temperature” means VDD1 thermal shutdown occurs “VDD1 low” means VDD1 below reset threshold “VDD1 low > 100 ms” means VDD1 below reset threshold for more than 100 ms “W/D: Trigger” means TIM1 register write operation. VSUP > BFew means VSUP > Battery Fall Early Warning (6.1 V typical) “W/D: timeout” means TIM1 register not written before W/D timeout period expired, or W/D written in incorrect time window if window W/D selected (except stop mode). In normal request mode timeout is 355 ms p2.2 (350 ms p3)ms. “SPI: Sleep” means SPI write command to MCR register, data sleep “SPI: Stop” means SPI write command to MCR register, data stop “SPI: Normal” means SPI write command to MCR register, data normal “SPI: Standby” means SPI write command to MCR register, data standby Note 1: these 2 SPI commands must be send in this sequence and consecutively. Note 2: if W/D activated Figure 16. Simplified State Machine 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 37 FUNCTIONAL DEVICE OPERATION OPERATIONAL MODES Behavior at SBC power up Figure 17. Behavior at SBC Power Up Transitions to enter debug modes W/D: timeout 350 ms Reset counter (1.0 ms) expired Power Down Reset W/D: Trigger Normal Request Normal SPI: MCR (0000) & Normal Debug Normal Debug SPI: MCR (0000) & Standby Debug Standby Debug Figure 18. Transitions to Enter Debug Modes 33889 38 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION OPERATIONAL MODES Simplified State machine in debug modes W/D: timeout 350ms R Trig ger R D eb ma Normal y or ld eb db SP I: n ug R Sleep ug E E SPI: Normal Debug SPI: standby debug SPI: Stop Standby W/ D: R I: St an R Wake-up Reset & !BATFAILNOSTOP & SPI: Sleep Reset counter (1ms) expired Normal Request SP Wake-up SPI: standby & W/D: Trigger Stop (1) SPI: Standby debug Standby Debug Normal Debug SPI: Normal debug R R (1) If stop mode entered, it is entered without watchdog, no matter the WDSTOP bit. (E) debug mode entry point (step 5 of the debug mode entering sequence). (R) represents transitions to reset mode due to Vdd1 low. Figure 19. Simplified State Machine in Debug Mode 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 39 FUNCTIONAL DEVICE OPERATION LOGIC COMMANDS AND REGISTERS LOGIC COMMANDS AND REGISTERS SPI INTERFACE MISO Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 A2 A1 A0 R/W D3 D2 D1 D0 MOSI Read operation: R/W bit = 0 Write operation: R/W bit = 1 address data Figure 20. Data Format Description The SPI is a 8 bit SPI. First 3 bits are used to identify the internal SBC register address, bit 4 is a read/write bit. The last 4 bits are data send from MCU to SBC or read back from SBC to MCU. During write operation state of MISO has no signification. During read operation only the last 4 bits at MISO have a meaning (content of the accessed register) Following tables describe the SPI register list, and register bit meaning. Registers “reset value” is also described, as well as the “reset condition”. reset condition is the condition which cause the bit to be set at the “reset value”. Possible reset condition are: Power On Reset: POR SBC mode transition: NR2R - Normal Request to Reset mode NR2N - Normal Request to Normal mode N2R - Normal to Reset mode STB2R - Standby to Reset mode STO2R - Stop to Reset mode SBC mode:RESET - SBC in Reset mode 33889 40 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION LOGIC COMMANDS AND REGISTERS Table 8. List of Registers Name Address Description Comment and usage MCR $0 0 0 Mode control register Write: Control of normal, standby, sleep, and stop modes Read: BATFAIL flag and other status bits and flags RCR $0 0 1 Reset control register Write: Configuration of reset voltage level, WD in stop mode, low power mode selection Read: CAN wake-up event, Tx permanent dominant CAN $0 1 0 CAN control register Write: CAN module control: TX/RX, Rec only, term VBAT, Normal and extended modes, filter at L0 input. Read: CAN failure status bits Write: HS1 (high-side switch) control in normal and standby mode. Gnd shift register level selection Read: HS1 over temp bit, SHIFT bit (gnd shift above selection), VSUP below 6.1V, V2 below 4.0 V IOR $0 1 1 I/O control register WUR $1 0 0 Wake-up input register TIM $1 0 1 Timing register LPC $1 1 0 Low power mode control register Write: HS1 periodic activation in sleep and stop modes Force wake-up control INTR $1 1 1 Interrupt register Write: Interrupt source configuration Read: INT source Write: Control of wake-up input polarity Read: Wake-up input, and real time LX input state Write: TIM1, Watchdog timing control, window or Timeout mode. Write: TIM2, Cyclic sense and force wake-up timing selection Register description Table 9. MCR Register MCR D3 $000b D2 D1 W R Reset D0 MCTR2 MCTR1 MCTR0 BATFAIL VDDTEMP GFAIL WDRST 0 0 0 0 POR, RESET POR, RESET POR, RESET Reset condition Table 10. Control bits MCTR2 MCTR1 MCTR0 SBC MODE 0 0 0 Enter/leave debug mode 0 0 1 Normal 0 1 0 Standby 0 1 1 Stop, watchdog off (2) DESCRIPTION To enter debug mode, SBC must be in Normal or Standby mode and BATFAIL(1) must be still at 1. To leave debug mode, BATFAIL must be at 0. 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 41 FUNCTIONAL DEVICE OPERATION LOGIC COMMANDS AND REGISTERS MCTR2 MCTR1 MCTR0 SBC MODE DESCRIPTION 0 1 1 Stop, watchdog on (2) 1 0 0 Sleep (3) 1 0 1 Normal 1 1 0 Standby 1 1 1 Stop (4) No watchdog running, debug mode (1): Bit BATFAIL cannot be set by SPI. BATFAIL is set when VSUP falls below 3V. (2): Watchdog ON or OFF depends on the RCR register bit D3. (3): Before entering sleep mode, bit NOSTOP in RCR register must be previously set to 1. (4): Stop command should be replaced by Stop Watchdog OFF. MCTR2=0, MCTR1= MCTR0=1 Table 11. Status bits STATUS BIT DESCRIPTION GFAIL Logic OR of CAN failure, HS1 failure, V2LOW BATFAIL Battery fail flag (VSUP<3V) VDDTEMP Temperature pre-warning on VDD (latched) WDRST Watchdog reset occurred Table 12. RCR register RCR $001b W D3 D2 WDSTOP NOSTOP R D1 D0 RSTTH TXFAILURE CANWU Reset 1 0 0 Reset condition POR, RESET POR, NR2N POR 33889 42 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION LOGIC COMMANDS AND REGISTERS Table 13. Control bits Status bit Bit value Description WDSTOP 0 No watchdog in stop mode 1 Watchdog runs in stop mode 0 Stop mode is default low power mode 1 Sleep mode is default low power mode 0 Reset threshold 1 selected (typ 4.6V) 1 Reset threshold 2 selected (typ 4.2V) CANWU 1 Wake-rom CAN TXFAILURE 1 Tx permanent dominant (CAN) NOSTOP RSTTH Table 14. CAN register Some description. CAN D3 D2 D1 D0 W FDIS CEXT CCTR1 CCTR0 R CS3 CS2 CS1 CS0 Reset 0 0 0 0 Reset condition POR, CAN POR, CAN POR, CAN POR, CAN $010b 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 43 FUNCTIONAL DEVICE OPERATION LOGIC COMMANDS AND REGISTERS Fault tolerant CAN transceiver standard modes The CAN transceiver standard mode can be programmed by setting CEXT to 0. The transceiver cell will then be behave as known from MC33388. Table 15. CAN Transceiver Modes CEXT CCTR1 CCTR0 Mode 0 0 0 TermVBAT 0 0 1 0 1 0 RxOnly 0 1 1 RxTx Table 16. CAN transceiver extended modes (CAN with CEXT bit =1 is not recommended) CEXT (1) CCTR1 CCTR0 Mode 1 0 0 TermVBAT 1 0 1 TermVDD 1 1 0 RxOnly 1 1 1 RxTx Fault tolerant CAN transceiver extended modes By setting CEXT to 1 the transceiver cell supports sub bus communication Note1: CEXT Bit should be set at 0. The CAN operation in extended mode is not recommended. FDIS L0 wake input filter (20 µs typical) 0 Enable (LO wake threshold selectable by WUR register) 1 Disable (L0 wake-up threshold is low level only, no matter D0 and D1 bits set in WUR register). Note: if DFIS bit is set to 1, WUR register must be read before going into sleep or stop mode in order to clear the wake-up flag. During read out L0 must be at high level and should stay high when entering sleep or stop. 33889 44 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION LOGIC COMMANDS AND REGISTERS Table 17. Status bits CS3 CS2 CS1 CS0 Bus failure # Description 0 0 0 0 0 0 0 1 1 0 1 0 1 5 0 1 1 0 8, 3a VDD 0 1 1 1 3 VBAT 1 0 0 1 2 1 1 0 1 4, 7 1 1 1 0 9 VDD 1 1 1 1 6 VBAT no failure CANH open wire CANH short circuit to ground CANL open wire CANL short circuit to ground / CANH Comments: CS2 bit at 0 = open failure. CS2 bit at 1 = short failure. (CS3 bit at 0 and (CS1 = 1 or CS2 =1)) = CANH failure. CS3 bit at 1 = CANL failure. CS1 and CS0 bits: short type failure coding (gnd, VDD or VBAT). In case of multiple failures, the last failure is reported. 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 45 FUNCTIONAL DEVICE OPERATION LOGIC COMMANDS AND REGISTERS Table 18. IOR register. IOR D3 D2 D1 D0 HS1ON GSLR1 GSLR0 HS1OT V2LOW VSUPLOW Reset 0 0 0 Reset condition POR, RESET POR, RESET POR, RESET $011b W R SHIFT Table 19. Control bits HS1ON HS1 0 HS1 switch turn OFF 1 HS1 switch turn ON Table 20. Gnd shift selection GSLR1 GSLR0 Typical gnd shift comparator level 0 0 -0.3 V 0 1 -0.7 V 1 0 -1.2 V 1 1 -1.7 V Shift State 0 Gnd shift value is lower than the level selected by the GSLR1 and GSLR2 bit 1 Gnd shift value is higher than the level selected by the GSLR1 and GSLR2 bit 33889 46 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION LOGIC COMMANDS AND REGISTERS Table 21. Status bits Status bit Description HS1OT (*) High-side 1 over temperature SHIFT gnd shift level selected by GSLR1 and GSLR2 bits is reached V2LOW V2 below 4.0 V typical VSUPLOW VSUP below 6.1 V typical (*) Once the HS1 switch has been turned off because of over temperature, it can be turned on again by setting the appropriate control bit to “1”. WUR REGISTER The local wake-up inputs L0 and L1 can be used in both normal and standby mode as port expander and for waking up the SBC in sleep or stop mode. Table 22. WUR Register WUR $100b D3 D2 D1 D0 W LCTR3 LCTR2 LCTR1 LCTR0 R L1WUb L1WUa L0WUb L0WUa 1 1 1 1 Reset Reset condition POR, NR2R, N2R, STB2R, STO2R Table 23. Control bits:. LCTR3 LCTR2 LCTR1 LCTR0 L0 configuration L1 configuration X X 0 0 inputs disabled X X 0 1 high level sensitive X X 1 0 low level sensitive X X 1 1 both level sensitive 0 0 X X inputs disabled 0 1 X X high level sensitive 1 0 X X low level sensitive 1 1 X X both level sensitive 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 47 FUNCTIONAL DEVICE OPERATION LOGIC COMMANDS AND REGISTERS Table 24. Status bits L0WUb L0WUa FDIS bit in CAN register Description 0 0 0 No wake-up occurred at L0 (sleep or stop mode). Low level state on L0 (standby or normal mode) 1 1 0 Wake-up occurred at L0 (sleep or stop mode). High level state on L0 (standby or normal mode) 0 1 1 Wake-up occurred at L0 (sleep or stop mode with L0 filter disable). WUR must be set to xx00 before sleep or stop mode. L1WUb L1WUa Description 0 0 No wake-up occurred at L1 (sleep or stop mode). Low level state on L1 (standby or normal mode) 1 1 Wake-up occurred at L1 (sleep or stop mode). High level state on L1 (standby or normal mode) TIM REGISTERS Description: This register is split into 2 sub registers, TIM1 and TIM2. TIM1 controls the watchdog timing selection as well as the window or timeout option. TIM1 is selected when bit D3 is 0. TIM2 is used to define the timing for the cyclic sense and forced wake-up function. TIM2 is selected when bit D3 is 1. No read operation is allowed for registers TIM1 and TIM2 TIM REGISTER Table 25. TIM Register. TIM1 D3 D2 D1 D0 0 WDW WDT1 WDT0 Reset 0 0 0 Reset condition POR, RESET POR, RESET POR, RESET $101b W R 33889 48 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION LOGIC COMMANDS AND REGISTERS Table 26. Watch dog WDW WDT1 WDT0 Watchdog timing [ms] 0 0 0 10 0 0 1 50 0 1 0 100 0 1 1 350 1 0 0 10 1 0 1 50 1 1 0 100 1 1 1 350 Table 27. jWatchdog operation (window and timeout) window closed window open for watchdog clear no watchdog clear WD timing * 50% no window watchdog window watchdog enabled (window lenght is half the watchdog timing) window open for watchdog clear WD timing * 50% Watchdog period (WD timing selected by TIM 1 bit WDW=1) Watchdog period (WD timing selected by TIM 1, bit WDW=0) Window watchdog Timeout watchdog TIM2 REGISTER The purpose of TIM2 register is to select an appropriate timing for sensing the wake-up circuitry or cyclically supplying devices by switching on or off HS1 Table 28. TIM2 Register TIM2 D3 D2 D1 D0 1 CSP2 CSP1 CSP0 Reset 0 0 0 Reset condition POR, RESET POR, RESET POR, RESET $101b W R 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 49 FUNCTIONAL DEVICE OPERATION LOGIC COMMANDS AND REGISTERS Table 29. Cyclic Sense Timing CSP2 CSP1 CSP0 Cyclic sense timing [ms] 0 0 0 5 0 0 1 10 0 1 0 20 0 1 1 40 1 0 0 75 1 0 1 100 1 1 0 200 1 1 1 400 Cyclic sense on time Cyclic sense timing 10 µs to 20 µs HS1 Sample t LPC REGISTER Description: This register controls: - The state of HS1 in stop and sleep mode (HS1 permanently off or HS1 cyclic) - Enable or Disable the forced wake-up function (SBC automatic wake-up after time spend in sleep or stop mode, time defined by TIM2 register) - Enable or disable the sense of the wake-up inputs (LX) at sampling point of the cyclic sense period (LX2HS1 bit). Table 30. LPC Register LPC D3 D2 D1 D0 LX2HS1 FWU IDDS HS1AUTO Reset 0 0 0 0 Reset condition POR, NR2R, N2R, STB2R, STO2R POR, NR2R, N2R, STB2R, STO2R POR, NR2R, N2R, STB2R, STO2R POR, NR2R, N2R, STB2R, STO2R $110b W R 33889 50 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION LOGIC COMMANDS AND REGISTERS LX2HS1 HS1AUTO Wake-up inputs supplied by HS1 Autotiming HS1 X 0 off X 1 On, HS1 cyclic, period defined in TIM2 register 0 X no 1 X Yes, LX inputs sensed at sampling point Bit Description FWU If this bit is set, and the SBC is turned into sleep or stop mode, the SBC wakes up after the time selected in the TIM2 register IDDS Bit = 0: IDDS-WU1 selected (lowest value, typ 3.5mA) Bit = 1: IDDS-WU2 selected (highest value, typ 14mA) Table 31. INTR register INTR D3 D2 D1 D0 W VSUPLOW HS1OT-V2LOW VDDTEMP CANF R VSUPLOW HS1OT VDDTEMP CANF Reset 0 0 0 0 Reset condition POR, RESET POR, RESET POR, RESET POR, RESET $111b Table 32. Control bits: Control bit Description CANF Mask bit for CAN failures (OR of any CAN failure) VDDTEMP Mask bit for VDD medium temperature HS1OT-V2LOW Mask bit for HS1 over temperature OR V2 below 4V VSUPLOW Mask bit for SUP below 6.1V When the mask bit has been set, INT pin goes low if the appropriate condition occurs. 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 51 FUNCTIONAL DEVICE OPERATION LOGIC COMMANDS AND REGISTERS Table 33. Status bits: Status bit Description CANF CAN failure VDDTEMP VDD medium temperature HS1OT HS1 over temperature VSUPLOW VSUP below 6.1V typical Notes: Bit D2 = 1: INT source is HS1OT If HS1OT-V2LOW interrupt is only selected (only bit D2 set Bit D2 = 0: INT source is V2LOW. in INTR register), reading INTR register bit D2 leads to two possibilities: Upon a wake-up condition from stop mode due to over current detection (IDD1S-WU1 or IDD1S-WU2), an INT pulse is generated, however INTR register contain remains at 0000 (not bit set into the INTR register). 33889 52 Analog Integrated Circuit Device Data Freescale Semiconductor TYPICAL APPLICATIONS TYPICAL APPLICATIONS 5V Q1 RB VBAT V2CTRL VSUP V2 VSUP monitor CAN supply Dual Voltage Regulator 5V/200mA VDD1 Monitor VDD1 5V/200mA Mode control HS1 control Oscillator HS1 INT Interrupt Watchdog Reset Programmable wake-up input L0 L1 WDOG RESET MOSI SCLK MISO CS SPI Interface RRTH RTH V2 Low Speed CANH TXD Fault Tolerant CAN CANL RRTL RXD GND Physical Interface RTL Figure 21. 33889D/33889B Simplified Typical Application with Ballast Transistor 5V/100mA VBAT V2CTRL (open) VSUP V2 VSUP Monitor Dual Voltage Regulator VDD1 Monitor CAN supply VDD1 5V/100mA 5V/200mA Mode Control HS1 Control Oscillator HS1 L0 L1 Programmable wake-up input INT Interrupt Watchdog Reset WDOG RESET MOSI SCLK MISO CS SPI Interface RRTH RTH CANH Low Speed Fault Tolerant CAN CANL RRTL Physical Interface V2 TX RX GND RTL Figure 22. 33889D/33889B Simplified Typical Application without Ballast Transistor 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 53 PACKAGING PACKAGE DIMENSIONS PACKAGING PACKAGE DIMENSIONS Important For the most current revision of the package, visit www.freescale.com and do a keyword search on the 98A number listed below. DW SUFFIX EG SUFFIX (PB-FREE) 28-PIN PLASTIC PACKAGE 98ASB42345B ISSUE G 33889 54 Analog Integrated Circuit Device Data Freescale Semiconductor PACKAGING PACKAGE DIMENSIONS DW SUFFIX EG SUFFIX (PB-FREE) 28-PIN PLASTIC PACKAGE 98ASB42345B ISSUE G 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 55 ADDITIONAL DOCUMENTATION THERMAL ADDENDUM (REV 1.0) ADDITIONAL DOCUMENTATION 33889 THERMAL ADDENDUM (REV 1.0) Introduction This thermal addendum is provided as a supplement to the MC33889 technical datasheet. The addendum provides thermal performance information that may be critical in the design and development of system applications. All electrical, application, and packaging information is provided in the datasheet. 28-PIN SOICW Packaging and Thermal Considerations The MC33889 is offered in a 28 pin SOICW, single die package. There is a single heat source (P), a single junction temperature (TJ), and thermal resistance (RθJA). TJ = RθJA . DWB SUFFIX 98ASB42345 28-PIN SOICW P The stated values are solely for a thermal performance comparison of one package to another in a standardized environment. This methodology is not meant to and will not predict the performance of a package in an applicationspecific environment. Stated values were obtained by measurement and simulation according to the standards listed below. Note For package dimensions, refer to the 33889 device datasheet. Standards Table 34. Thermal Performance Comparison Thermal Resistance ΡθJA (1) (2) ΡθJB (2) (3) ΡθJA (1) (4) ΡθϑΧ (5) [°C/W] 42 11 69 23 Notes 1. Per JEDEC JESD51-2 at natural convection, still air condition. 2. 2s2p thermal test board per JEDEC JESD51-7. 3. Per JEDEC JESD51-8, with the board temperature on the center trace near the center lead. 4. Single layer thermal test board per JEDEC JESD51-3. 5. Thermal resistance between the die junction and the package top surface; cold plate attached to the package top surface and remaining surfaces insulated. 20 Terminal SOICW 1.27 mm Pitch 18.0 mm x 7.5 mm Body Figure 23. Surface Mount for SOIC Wide Body Non-Exposed Pad 33889 56 Analog Integrated Circuit Device Data Freescale Semiconductor ADDITIONAL DOCUMENTATION THERMAL ADDENDUM (REV 1.0) RX TX VDD1 RST INT GND GND GND GND V2CTRL VSUP HS1 L0 L1 1 28 2 27 3 26 4 25 5 24 6 23 7 22 8 21 9 20 10 19 11 18 12 17 13 16 14 15 A WDOG CS MOSI MISO SCLK GND GND GND GND CANL CANH RTL RTH V2 33889DWB Pin Connections 28-Pin SOICW 1.27 mm Pitch 18.0 mm x 7.5 mm Body Figure 24. Thermal Test Board Device on Thermal Test Board Material: Outline: Area A: Ambient Conditions: Single layer printed circuit board FR4, 1.6 mm thickness Cu traces, 0.07 mm thickness 80 mm x 100 mm board area, including edge connector for thermal testing Cu heat-spreading areas on board surface Natural convection, still air Table 35. Thermal Resistance Performance Thermal Resistance Area A (mm2) (°C/W) ΡθJA 0 69 300 53 600 48 ΡθJA ισ τηε τηερµαλ ρεσιστανχε βετωεεν διε ϕυνχτιον ανδ αµβιεντ αιρ. 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 57 ADDITIONAL DOCUMENTATION THERMAL ADDENDUM (REV 1.0) Thermal Resistance [ºC/W] 80 70 60 50 40 x ΡθJA 30 20 10 0 0 300 Heat spreading area A [mm²] 600 Figure 25. Device on Thermal Test Board RθJA Thermal Resistance [ºC/W] 100 10 x ΡθJA 1 0.1 1.00E-03 1.00E-02 1.00E-01 1.00E+00 1.00E+01 1.00E+02 1.00E+03 1.00E+04 Time[s] Figure 26. Transient Pin Resistance ΡθJA Device on Thermal Test Board Area A = 600 (mm2) 33889 58 Analog Integrated Circuit Device Data Freescale Semiconductor REVISION HISTORY REVISION HISTORY REVISION DATE DESCRIPTION OF CHANGES 7.0 5/2006 8.0 6/2002 • • • • • • • • • 9.0 8/2006 • 10.0 9/2006 • 11.0 12/2006 • • Implemented Revision History page Added “EG” PB-Free package type Removed MC33889DW version, and added MC33889B and MC33889D versions Converted to the Freescale format, and updated to the prevailing form and style Modified Device Variations Between the 33889D and 33889B Versions (1) on page 2 Added Thermal Addendum (rev 1.0) on page 56 Changed the Maximum Ratings on page 6 to the standard format Added CAN transceiver description section Corrected two instances where pin LO had an overline, and one instance where pin WDOG did not. Removed MC33889BEG/R2 and MC33889DEG/R2 and replaced them with MCZ33889BEG/R2 and MCZ33889DEG/R2 in the Ondering Information block Replaced the label Logic Inputs with Logic Signals (RX, TX, MOSI, MISO, CS, SCLK, RST, WDOG, INT) on page 6 Changed CS to CS at various places in the document Made changes to Supply Current in Stand-by Mode (7),(9) on page 8 and Supply Current in Normal Mode (7) on page 8 33889 Analog Integrated Circuit Device Data Freescale Semiconductor 59 How to Reach Us: Home Page: www.freescale.com Web Support: http://www.freescale.com/support USA/Europe or Locations Not Listed: Freescale Semiconductor, Inc. Technical Information Center, EL516 2100 East Elliot Road Tempe, Arizona 85284 +1-800-521-6274 or +1-480-768-2130 www.freescale.com/support Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) www.freescale.com/support Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 [email protected] Asia/Pacific: Freescale Semiconductor Hong Kong Ltd. Technical Information Center 2 Dai King Street Tai Po Industrial Estate Tai Po, N.T., Hong Kong +800 2666 8080 [email protected] For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 or 303-675-2140 Fax: 303-675-2150 [email protected] MC33889 Rev. 11.0 12/2006 RoHS-compliant and/or Pb-free versions of Freescale products have the functionality and electrical characteristics of their non-RoHS-compliant and/or non-Pb-free counterparts. For further information, see http://www.freescale.com or contact your Freescale sales representative. For information on Freescale’s Environmental Products program, go to http:// www.freescale.com/epp. Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”, must be validated for each customer application by customer’s technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © Freescale Semiconductor, Inc., 2006. All rights reserved.