SURE STAR Issued Date : 11/15/2012 SURE STAR SPECIFICATION 產品規格書 產品名稱 / Model Name： ：M1C-600A1 產品描述 / Description: 600W Power Supply for 1U Easy Swap – 62Pins. 5 outputs (+12V, +5V, -12V,+3.3V, 5V SB) 版本 / Revision： ：1.1 修改紀錄 / Revision History 版本 日期 版本描述 Rev. Date Revision Description 修改者 認可日期 Modify By Cust. Approval App. Date 1.0 Aug. .08, 2011 Modified the circuit for DC-DC backplane Kevin Chen 1.1 Nov. 15, 2012 Add the HE/LN stick and description. Mindy Chung 提交 / Prepared BY 客戶認可 檢查 / Checked BY KEVIN Aug.10, 2011 Nov. 16, 2012 批准 / Approved BY JACKY ① SURE STAR SURE STAR 目錄 Contents 1. 概述 General Description 2. 輸入規格 Input Characteristics 2.1. 交流輸入電壓和頻率範圍 AC Input voltage and frequency 2.2. 輸入電流與浪湧電流 Input current and inrush current 2.3. 功率因數 POWER FACTOR 3. 效率 Power Efficiency 4. 輸出規格 Output Characteristics 4.1. 輸出電壓電流調整率 Output Voltage & Current Regulation 4.2. 輸出紋波和噪音 DC Output Ripple & Noise 4.3. 4.4. 4.5. 4.6. 輸出保持時間 Hold Up Time 上升時間 Rise Time 動態響應時間 Dynamic load response time 遠端開關控制 Remote on/off control 5. 電源良好信號 Power good signal 6. 保護 PROTECTION 6.1. 過壓保護 Over voltage protection 6.2. 低壓保護 Under-voltage protection 6.3. 過流保護 Over current Protection 6.4. 短路保護 Short circuit protection 7. 電源信號狀態 Power System Signal status 7.1. 蜂鳴器狀態 Buzzer status 7.2. 燈號指示 LED indicators 7.3. TTL信號 TTL signal 8. 負載均流 Load sharing ② SURE STAR SURE STAR 9. 絕緣性能 Isolation 9.1. 絕緣電阻 Insulation Resistance 9.2. 耐壓絕緣 Dielectric Withstand Voltage 9.3. 漏電電流 Leakage current 10. 安全要求 安全要求 Safety Requirements 11. 電磁相容 EMC 11.1. 電磁干擾 EMI 11.2. 電磁相容 EMS 12. 環境條件Environmental 環境條件 12.1. 溫度 Temperature 12.2. 環境濕度 Humidity 12.3. 海拔高度 Altitude 12.4. 振動耐受 Vibration 12.5. 衝擊耐受 Shock 12.6. 冷卻方式 Cooling Method 13. 可靠性 Reliability 13.1平均故障失效時間 MTBF Qualification 14. 機械尺寸和電源連接器 機械尺寸和電源連接器 Mechanical 2D Drawing and Power Connector 14.1. 外觀尺寸圖 Outside Dimension 14.2. 輸出端線材 DC Output 62pin spec ③ SURE STAR SURE STAR 1. 概述 General Description This specification describes the performance characteristics of a 600 watts easy swappable, power system with +3.3V,+5V,+12V, -12V main DC outputs, and 5V standby outputs. SURE STAR Model M1C-600A1. 2. 輸入規格 Input Characteristics 2.1. 交流輸入電壓和頻率範圍 AC Input voltage and frequency 最小值 正常值 最大值 單位 Minimum Nominal Maximum Unit 90 100~240 264 伏特 VAC 47 50~60 63 赫茲 Hz 2.2. 輸入電流與浪湧電流 Input current and inrush current 交流輸入電壓 最大輸入電流 浪湧電流 AC Input Voltage MAX. Input Current Inrush Current per power supply module per power supply module 115Vac 10A 25A 230Vac 5A 50A 2.3. 功率因數 Power Factor 90Vac 115Vac 230Vac 264Vac ＞0.99 ＞0.98 ＞0.95 ＞0.92 3. 效率 Power Efficiency 在滿載狀態，115 伏特 60 赫茲輸入下，電源效率為 80%(Min)。 The Minimum efficiency of the power supply is 80% at full load and 1150Vac/60HZ input. ④ SURE STAR SURE STAR 4. 輸出規格 Output Characteristics 4.1. 輸出電壓電流調整率 Output Voltage & Current Regulation 輸出電壓 最小電流 額定電流 調整率 Output Voltage Min. Current Rated current REGULATION +3.3V 1A 25A ±5％ +5V 1A 25A ±5％ +12V 1A 49A ±5％ -12V 0A 1A ±5％ +5VSB 0.5A 3.5A Note: 5V 和 3.3V 相加總不可超過 180 瓦. ±5％ The combined total power from 5V & 3.3V shall not exceed 180W. 4.2. 輸出紋波和噪音 DC Output Ripple & Noise Output Voltage Ripple & Noise (Max.) +3.3V 60mVp-p +5V 60mVp-p +12V 120mVp-p -12V 120mVp-p +5VSB 50mVp-p Note: 1. 紋波和噪音頻寬設置在 20 兆赫茲。 Ripple & Noise bandwidth is set to 20MHz。 2. 輸出端並聯一個 0.1 uF 陶瓷電容和一個 10 uF 電解電容來測試紋波和噪音。 Use a 0.1uF ceramic capacitor in parallel with a 10uF electrolytic capacitor at output connector terminals for ripple & noise measurements。 4.3. 輸出保持時間 Hold Up Time Output Voltage 115VAC Input 230VAC Input +3.3V ＞16ms ＞16ms +5V ＞16ms ＞16ms +12V ＞16ms ＞16ms -12V ＞16ms ＞16ms ＞16ms ＞16ms +5VSB Note: 所有輸出在滿載狀態 All of dc output at full load.。 ⑤ SURE STAR SURE STAR 4.4. 上升時間 Rise Time Output Voltage 115/230Vac Input & Full Load +3.3V 20ms (max.) +5V 20ms (max.) +12V 20ms (max.) -12V 20ms (max.) +5VSB 20ms (max.) Note: 上升時間為輸出電壓從10%上升至90%的時間。 The rise time measured is when the output voltages rise from10% to 90% of specified output voltage Vout observed on the channel waveform. 4.5. 動態響應時間 Dynamic load response time The following shall apply to the 3.3 V, 5 V, and 12 V outputs: Output voltage for each output shall recover to within 5 % of its steady state level in less than 1 ms under the following conditions: AC Input Voltage: 90VAC ~ 264VAC Repetition rate of 100Hz with 50 % duty cycle Output Step Load Size Load Slew Rate Capacitive Load +3.3V 30% to 100% to 30% load 0.5 A/u sec 6000uF +5V 30% to 100% to 30% load 0.5 A/u sec 6000uF +12V 60% to 100% to 60% load 1 A/u sec 6000uf +5SB 0% to 100% to 0% load 0.5 A/u sec 350uF 4.6. 遠端開關控制 Remote on/off control The main outputs of this power supply (3.3V,5V,12V,-12V) shall be energized when input signal*PSON is active. *PSON is an active low TTL compatible signal referenced to the +5V standby common. This input signal shall be an open collector signal capable of sinking a minimum of 1.6mA. When *PSON becomes inactive, the main outputs shall be disabled. PSON Signal PSU on PSU off LOW (0.8V max) HI (2V max) ⑥ SURE STAR SURE STAR 5. 電源良好信號 Power good signal The system shall have an active high TTL compatible signal capable of sinking 1mA and sourcing 100uA. The signal shall become active within 100 to 500 ms from the instant +5V output reaches a steady state level within the specified regulation limits. It shall become inactive at least 1 ms before +5V drops to below the lower regulation limit. Power good @ 115/230VAC , Full Load 200ms ~ 500ms Power Fail @ 115/230VAC , Full Load 1ms (Min.) 6. 保護 Protection 6.1. 過壓保護 Over voltage protection Output Min Max Comments +3.3V 3.75V 4.3V PSU shutdown +5V 5.7V 6.9V PSU shutdown +12V 13V 14.3V PSU shutdown Note：應該在最大交流輸入電壓230伏和輕載、空載下測試。 The power supply shall be test at max AC voltage (230Vac) and min load or no load. 6.2. 低壓保護 Under-voltage protection Output Min Max Comments +3.3V 2.0V 2.4V PSU shutdown +5V 3.3V 3.7V PSU shutdown +12V 8.5V 9.5V PSU shutdown Note：應該在最大交流輸入電壓230伏和輕載、空載下測試。 The power supply shall be test at max AC voltage (230Vac) and min load or no load. 6.3. 過流保護 Over current protection Output +3.3V Over Current(Type) ≧27.5A Over Current(Max.) Comments 37.5A PSU shutdown +5V ≧27.5A 37.5A PSU shutdown +12V ≧53.9A 73.5A PSU shutdown Note：過流保護測試是在其他額定負載時測試。 The over current protection should be tested at other load rating. ⑦ SURE STAR SURE STAR 6.4. 短路保護 Short circuit protection Output Comments +3.3V PSU shutdown +5V PSU shutdown +12V PSU shutdown Note：短路保護測試是在其他額定負載時測試。 The Short circuit protection should be tested at other load rating. 7. 電源信號狀態 Power System Signal status 7.1. 蜂鳴器狀態 Buzzer status Power Supply Condition Buzzer status No AC power to all PSU OFF AC present/Only Standby Output On OFF Power supply DC outputs ON and OK OFF Power supply failure Beeping 7.2. 燈號指示 LED indicators Power Supply Condition Power system status Per Power Module status LED Color RED GREEN ORANGE No AC power to all PSU OFF OFF OFF AC present/Only Standby Output On ON OFF OFF Power supply DC outputs ON and OK OFF ON ON Power supply failure OFF Blinking OFF ⑧ SURE STAR SURE STAR 7.3. TTL 信號 TTL signal POWER SUPPLY CONDITION OUTPUT CONDITION Min. Max. NORMAL(POWER SUPPLY ON) 3V 5.25V FAILURE(POWER SUPPLY OFF) 0V 1V 8. 負載均流 Load sharing 輸出電壓 負載電流 負載均流電壓 Output Voltage Load Current Load Share Voltage +12V 1A +0.48V ~ +0.52V +5V 1A +0.33V ~ +0.37V +3.3V 1A +0.33V ~ +0.37V 9. 絕緣性能 Isolation 9.1. 絕緣電阻 Insulation Resistance Input To Output 500Vdc , 50M ohms Min.( at room Temperature) Input To FG 500Vdc , 50M ohms Min.( at room Temperature) Output To FG Non Insulation 9.2. 耐壓絕緣 Dielectric Withstand Voltage Input To Output 1834Vac (30 mA) for 1 Minute. Input To FG 1834Vac (30 mA) for 1 Minute. Output To FG Non Insulation 9.3. 漏電電流 Leakage current 在120-264 伏特/50-60 赫茲情況下最大漏電流為3.5mA。 3.5mA max. at 120~264Vac/50~60HZ. 10. 安全要求 安全要求 Safety Requirements -IEC 950 -CB REPORT -TUV EN 60950 -UL or cUL -BSMI -CCC ⑨ SURE STAR SURE STAR 11. 電磁相容 EMC 電源電磁干擾滿足以下標準 The power supply shall comply with the following criterion: 11.1. 電磁干擾 EMI 1) Conduction Emission:（傳導干擾度） A.EN55013/EN55022, CLASS B B.CISPR13:2001/FCC PART15 CLASS B 2) Radiated Emission : (幅射干擾度) A.EN55013/EN55022, CLASS B B.CISPR13:2001/FCC PART15 CLASS B 12. 環境條件Environmental 環境條件 12.1. Temperature Operating : 0℃to +40℃ Non Operating: -20℃to +70℃ 12.2. Humidity Operating : 5% to 95%, non-condensing Non Operating: 20% to 90%,non-condensing 12.3. Altitude Operating: sea level to 7,000 feet Non-operating: sea level to 40,000 feet 12.4. 振動耐受 Vibration 10-55Hz, 19.6m/s²(2G), 3minutes period, 60minutes each along X, Y and Z axis. 12.5. 衝擊耐受 Shock 49m/s²(5G),11ms, once each X, Y and Z axis. 12.6. 冷卻方式 Cooling Method BY BALL BEARING DC FAN. 13. 可靠性 Reliability 13.1 平均故障失效時間 MTBF Qualification Using MIL - HDBK -217F the calculated MTBF＞100,000 hours at 25℃ ⑩ 14. 機械尺寸和電源連接器 機械尺寸和電源連接器 Mechanical 2D Drawing and Power Connector 14.1. Outside Dimension: 247.9(D)x106(W)x40(H)mm 版次 REV 修訂 REVISIONS 記述 DESCRIPION 簽名 SING 日期 DATE 手轉彈簧螺絲 M3x0.5 容許公差: 材料規格 單位 TOLEANCES: MATERIAL .XXX= ± .025 審核者 繪圖者 核准者 .XX= ± .1 ± .5 .X= APPROVE BY CHECK BY DRAW BY 圖號 投影法: 編號 PROJECTION: 第三角法 14.2. DC Output pins assignment: 62Pins Golden Finger. ⑪ UNITS mm SURE STAR DRAW NO SHEET JACKY 日期 DATE OF 品名 MODEL NO 料號 Dec.30.2010 PART NO SS-XXXR62外觀尺寸圖