Microdc D120505XM 1w,fixed input,1000v isolated & unregulated twin output dc-dc converter Datasheet

D-XM Series
1W,FIXED INPUT,1000V ISOLATED & UNREGULATED TWIN OUTPUT DC-DC CONVERTER
SELECTION GUIDE
Input
Output
Output
Voltage
Voltage1
Voltage2
Output
Current1
Output
Current2
(V)
(V)
(V)
(MA)
(MA)
D050503XM
5
5
3.3
100
RD050505XM
5
5
5
50
D050505XM
5
5
5
D050509XM
5
5
D050512XM
5
5
D050515XM
5
5
RD120505XM
12
D120505XM
Efficiency
(%)
MTTF1
(KHRS)
152
70
1615
50
70
146
100
100
70
1615
9
100
56
80
669
12
100
42
80
339
15
100
34
80
187
5
5
50
50
84
135
12
5
5
100
100
70
489
D120509XM
12
5
9
100
56
80
343
D120512XM
12
5
12
100
42
80
229
D120515XM
12
5
15
100
34
80
148
RD240505XM
24
5
5
50
50
84
130
D240505XM
24
5
5
100
100
81
395
D240509XM
24
5
9
100
56
82
289
D240512XM
24
5
12
100
42
84
186
D240515XM
24
5
15
100
34
84
150
Order code
FEATURES
◆
Small footprint
◆
Temperature range: -40℃~+85℃
◆
1KVDC isolation
◆
No Heat sink required
◆
No external component required
◆
◆
◆
Internal SMD Construction
Industry standard pinout
RoHS Compliance
MODEL SELECTION
①
②
③
④
⑤
⑥
D 05 05 05 X M
①Product Series
②Input Voltage
③The 1st Output Voltage ④The 2nd Output Voltage
⑤Fixed Input
⑥Mini SIP Package Style
COMMON SPECIFICATIONS
Item
Test Conditions
Min.
Typ.
Storage humidity range
APPLICATIONS
The D-XM Series are specially designed for
applications where a group of polar power
supplies are isolated from the input power
supply in a distributed power supply system on
a circuit board.
These products apply to:
1) Where the voltage of the input power
supply is fixed (voltage variation ≤±10%);
2) Where isolation is necessary between
input and output(isolation voltage ≤1000VDC);
3) Where the regulation of the output voltage
and the output ripple noise are not demanding.
Such as:purely digital circuits, ordinary low
frequency analog circuits,and IGBT power
device driving circuits.
Max.
Units
95
%
Operating temperature
-40
85
Storage temperature
-55
125
℃
Lead temperature
1.5mm from case for 10 seconds
300
15
Temp. rise at full load
1
Short circuit protection*
S
Free air convection
Cooling
Plastic(UL94-V0)
Case material
MTBF
25
3500
Weight
K hours
1.4
g
*Supply voltage must be discontinued at the end of short circuit duration.
MICRODC R ESERVES THE COPYRIGHT
http://www.microdc.cn
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 1 of 3
D-XM Series
TYPICAL CHARACTERISTICS
ISOLATION SPECIFICATIONS
Item
Test Conditions
Min.
Typ.
Max.
Units
Isolation voltage (Vin/Vout)
Tested for 1 minute and 1mA max
1000
VDC
Isolation voltage (Vo1/Vo2)
Tested for 1 minute and 1mA max
1000
VDC
Isolation resistance (Vin/Vout)
Test at 500VDC
1000
MΩ
Isolation resistance (Vo1/Vo2)
Test at 500VDC
1000
MΩ
Isolation capacitance(Vin/Vout)
30
pF
Isolation capacitance(Vo1/Vo2)
30
pF
OUTPUT SPECIFICATIONS
Item
Test Conditions
Output power
Min.
Typ.
0.1
Line regulation
For Vin change of 1%
Load regulation
10% to 100% load (3.3V output)
Load regulation
10% to 100% load(5V output)
Output voltage accuracy
Max.
Units
1
W
±1.5
%
15
20
%
12.8
15
%
RECOMMENDED CIRCUIT
See tolerance envelope graph
Temperature drift
100% full load
Ripple & Noise*
20MHz Bandwidth
75
Switching frequency
Full load, nominal input
130
*Test ripple and noise by "Parallel cable"method. See detailed operation
±0.03
%/℃
100
mVp-p
KHz
instructions at Testing of Power
Converter section, application notes.
APPLICATION NOTE
Requirement on output load
To ensure this module can operate efficiently and reliably, During operation, the minimum output load
could not be less than 10% of the full load. If the actual output power is very small, please connect a
resistor with proper resistance at the output end in parallel to increase the load , or use our company
products with a lower rated output power.
Recommended circuit
If you want to further decrease the input/output ripple , an "LC" filtering network may be connected to
the input and output ends of the DC/DC converter, see (Figure 1).
It should also be noted that the inductance and the frequency of the "LC" filtering network should be
staggered with the DC/DC frequency to avoid mutual interference. However , the capacitance of the output
filter capacitor must be proper. If the capacitance is too big,a startup problem might arise. For every channel
of output , provided the safe and reliable operation is ensured , the recommended capacitance of its filter
capacitor sees (Table 1).
Output Voltage Regulation and Over-voltage Protection Circuit
The simplest device for output voltage regulation, over-voltage and over-current protection is a linear
voltage regulator with overheat protection that is connected to the input or output end in series (Figure 2).
It's not
recommended to connect any external capacitor in the
application field with less than 0.5 watt output.
Overload Protection
Under normal operating conditions, the output circuit of these products has no protection against
overload.The simplest method is to connect a self-recovery fuse in series at the input end or add a circuit
breaker to the circuit.
No parallel connection or plug and play
http://www.microdc.cn
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 2 of 3
D-XM Series
OUTLINE DIMENSIONS & FOOTPRINT DETAILS
MECHANICAL DIMENSIONS
RECOMMENDED FOOTPRINT
TUBE OUTLINE DIMENSIONS
Note:
Unit:mm[ inch]
Pin sect ion tolerances:±0.10mm[±0.004inch]
General tolerances:±0.25mm[±0.010inch]
Note:
Unit :mm[inch]
General tolerances:±0.50mm[±0.020inch]
L=530mm[20.866inch]
Tube Quantity: 30pcs
L=220mm[8.661inch]
Tube Quantity: 11pcs
RoHS COMPLIANT INFORMATION
This series is compatible with RoHS soldering systems with a peak wave solder temperature
of 300°C for 10 seconds.
The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin
with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this
series are backward compatible with Sn/Pb soldering systems.
Microdc Professional Power Module,Inc.
Tel:0086-20-86000646
E-mail:[email protected]
Website:http://www.microdc.cn
http://www.microdc.cn
REACH COMPLIANT INFORMATION
This series has proven that this product does not contain harmful chemicals, it also has
harmful chemical substances through the registration, inspection and approval.
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 3 of 3
Similar pages