LED Display Product Data Sheet LTS-2807CKD-P Spec No.: DS30-2013-0118 Effective Date: 07/02/2014 Revision: A LITE-ON DCC RELEASE BNS-OD-FC001/A4 LITE-ON Technology Corp. / Optoelectronics No.90,Chien 1 Road, Chung Ho, New Taipei City 23585, Taiwan, R.O.C. Tel: 886-2-2222-6181 Fax: 886-2-2221-1948 / 886-2-2221-0660 http://www.liteon.com/opto LED DISPLAY LTS-2807CKD-P LED DISPLAY LTS-2807CKD-P Rev Description By Date 01 Preliminary Spec. Reo Lin 02/08/2013 02 Revised error for packing spec. in page 9 Reo Lin 10/21/2013 Above data for PD and Customer tracking only - NPPR Received and Upload on System Reo Lin 10/21/2013 A Modify symbol location in page 3 Reo Lin 06/26/2014 1/12 Part No. : LTS-2807CKD-P BNS-OD-FC002/A4 LED DISPLAY LTS-2807CKD-P 1. Description The LTS-2807CKD-P is a 0.2 inch (5.08mm) digit height single digit SMD display. This device uses AS-AlInGap hyper red chips(AlInGap epi on GaAs substrate). The display has gray face and white segments. 1.1 Features 0.2 inch (5.08 mm) DIGIT HEIGHT CONTINUOUS UNIFORM SEGMENTS LOW POWER REQUIREMENT EXCELLENT CHARACTERS APPEARANCE HIGH BRIGHTNESS & HIGH CONTRAST WIDE VIEWING ANGLE SOLID STATE RELIABILITY CATEGORIZED FOR LUMINOUS INTENSITY. LEAD-FREE PACKAGE(ACCORDING TO ROHS) 1.2 Device Part No Description AlInGap Hyper Red Common Anode LTS-2807CKD-P Rt. Hand Decimal 2/12 Part No. : LTS-2807CKD-P BNS-OD-FC002/A4 LED DISPLAY LTS-2807CKD-P 2. Package Dimensions 10 6 6 10 1 5 5 1 Notes : 1. All dimensions are in millimeters. Tolerances are 0.25 mm (0.01“) unless otherwise noted 2. Foreign material on segment ≦10mil 3. Ink contamination (surface) ≦20mils 4. Bubble in segment ≦10mil 5. Bending ≦ 1% of reflector length 6. Plastic pin’s burr max is 0.05 mm 3/12 Part No. : LTS-2807CKD-P BNS-OD-FC002/A4 LED DISPLAY LTS-2807CKD-P 3. Internal Circuit Diagram 4/12 Part No. : LTS-2807CKD-P BNS-OD-FC002/A4 LED DISPLAY LTS-2807CKD-P 4. Pin Connection No Connection 1 CATHODE E 2 CATHODE D 3 COMMON ANDOE 4 CATHODE C 5 CATHODE DP 6 CATHODE B 7 CATHODE A 8 COMMON ANODE 9 CATHODE F 10 CATHODE G 5/12 Part No. : LTS-2807CKD-P BNS-OD-FC002/A4 LED DISPLAY LTS-2807CKD-P 5. Rating and Characteristics 5.1. Absolute Maximum Rating at Ta=25°C Parameter Maximum Rating Unit 70 mW 60 mA 25 mA 0.28 mA/°C Power Dissipation Per Segment Peak Forward Current Per Segment ( 1/10 Duty Cycle, 0.1ms Pulse Width ) Continuous Forward Current Per Segment Derating Linear From 25°C Per Segment Operating Temperature Range -35°C to +105°C Storage Temperature Range -35°C to +105°C Iron Soldering Conditions: 1/16 inch Below Seating Plane for 3 Seconds at 260°C 5.2.Electrical / Optical Characteristics at Ta=25°C Parameter Symbol Average Luminous Intensity Per Segment IV MIN. TYP. 201 650 MAX. Unit cd Test Condition IF=1mA IF=10mA 8250 Peak Emission Wavelength p 650 nm IF=20mA Spectral Line Half-Width 20 nm IF=20mA Dominant Wavelength d 639 nm IF=20mA Forward Voltage Per Chip VF 2.05 2.6 V IF=20mA Reverse Current Per Segment(2) IR 100 A VR=5V IV-m 2:1 Luminous Intensity Matching Ratio IF=1mA (Similar Light Area) Notes : 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE (Commission International De L’Eclariage) eye-response curve 2. Reverse voltage is only for IR test. It cannot continue to operate at this situation 3. Cross talk specification ≦ 2.5% 6/12 Part No. : LTS-2807CKD-P BNS-OD-FC002/A4 LED DISPLAY LTS-2807CKD-P 5.3. Typical Electrical / Optical Characteristics Curves (25°C Ambient Temperature Unless Otherwise Noted) 7/12 Part No. : LTS-2807CKD-P BNS-OD-FC002/A4 LED DISPLAY LTS-2807CKD-P 6. SMT SOLDERING INSTRUCTION (Number of reflow process shall be less than 2 times, and cooling process to normal temperature is required between the first and the second soldering process) Notes : 1. Recommended soldering condition Reflow Soldering (Two times only) Pre-heat: 120~150°C. Pre-heat time: 120sec. Max. Peak temperature: 260°C Max. Soldering time: 5sec. Max. Soldering Iron (One time only) Temperature 300°C Max. Soldering time 3sec. Max. 2. Number of reflow process shall be less than 2 times, and cooling process to normal temperature is required between the first and the second soldering process. 8/12 Part No. : LTS-2807CKD-P BNS-OD-FC002/A4 LED DISPLAY LTS-2807CKD-P 7. Recommended Soldering Pattern 9/12 Part No. : LTS-2807CKD-P BNS-OD-FC002/A4 LED DISPLAY LTS-2807CKD-P 8. Packing Specification 8.1. Packing Reel Dimensions 330.0±2.0 9 10 +1 29.4-0.5 100.0±0.5 +0.5 2.0-0 21.0± 0.5 +0.5 13.0-0.2 6 120° PS 34 12 78 56 +2 24.4-0 10/12 Part No. : LTS-2807CKD-P BNS-OD-FC002/A4 1112 02 03 01 04 00 05 LED DISPLAY LTS-2807CKD-P 8.2. Packing Carrier Dimensions 1. 10 sprocket hole pitch cumulative tolerance ±0.20. 2. Carrier camber is within 1 mm in 250 mm. 3. Material : Black Conductive Polystyrene Alloy. 4. All dimensions meet EIA-481-D requirements. 5. Thickness : 0.30±0.05mm. 6. Packing length per 22" reel : 56.5 Meters.(1:3) 7. Component load per 13" reel : 1000 pcs. 8.3.Trailer part / Leader part (40mm MIN.) (400mm MIN.) (40mm MIN.) DIRECTION OF PULLING OUT 11/12 Part No. : LTS-2807CKD-P BNS-OD-FC002/A4 LED DISPLAY LTS-2807CKD-P 9. Moisture Proof Packing All N/D SMD displays are shipped in moisture proof package. The displays should be stored at 30°C or less and60% RH or less. Once the package opened, moisture absorption begins. If the parts are not stored in dry conditions, they must be baked before reflow to prevent damage to the parts. Baking should only be done once Package In Reel In Bulk Temperature 60°C 100°C 125°C Time ≧48hours ≧4hours ≧2hours 12/12 Part No. : LTS-2807CKD-P BNS-OD-FC002/A4