LTM4604A Low Voltage, 4A DC/DC µModule with Tracking FEATURES ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ DESCRIPTION Complete Standalone Power Supply ±1.75% Total DC Output Error (–40°C to 125°C) Wide Input Voltage Range: 2.375V to 5.5V 4A DC, 5A Peak Output Current 0.8V to 5V Output Output Voltage Tracking UltraFastTM Transient Response Power Good Indicator Current Mode Control Current Foldback Protection, Parallel/Current Sharing Up to 95% Efficiency Programmable Soft-Start Micropower Shutdown: IQ ≤ 7μA Overtemperature Protection Small and Very Low Profile Package: 15mm × 9mm × 2.3mm LGA (0.630mm Pads) APPLICATIONS ■ ■ ■ ■ ■ Telecom and Networking Equipment Servers Storage Cards ATCA Cards Industrial Equipment , LT, LTC and LTM are registered trademarks of Linear Technology Corporation. μModule and UltraFast are trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. The LTM®4604A is a complete 4A switch mode DC/DC power supply with ±1.75% total output voltage error. Included in the package are the switching controller, power FETs, inductor and all support components. Operating over an input voltage range of 2.375V to 5.5V, the LTM4604A supports an output voltage range of 0.8V to 5V, set by a single resistor. This high efficiency design delivers up to 4A continuous current (5A peak). Only bulk output capacitors are needed to complete the design. The 0.630mm LGA pads with 1.27mm pitch simplify PCB layout by providing standard trace routing and via placement. (The LTM4604A has smaller pads than the LTM4604.) The low profile package (2.3mm) enables utilization of unused space on the bottom of PC boards for high density point of load regulation. High switching frequency and a current mode architecture enable a very fast transient response to line and load changes without sacrificing stability. Fault protection features include foldback current protection, thermal shutdown and a programmable soft-start function. The LTM4604A is offered in a small thermally enhanced 15mm × 9mm × 2.3mm LGA package and is Pb free and RoHS compliant. TYPICAL APPLICATION Efficiency vs Output Current 100 3.3V to 2.5V/4A μModule™ Regulator VIN = 3.3V VOUT = 2.5V 95 VIN 3.3V VIN PGOOD VOUT 2.5V 4A VOUT LTM4604A COMP FB RUN/SS TRACK GND VIN 2.37k EFFICIENCY (%) 90 10μF 6.3V 85 80 75 22μF 6.3V ×2 70 4604A TA01a 65 0 1 2 3 OUTPUT CURRENT (A) 4 4604A TA01b 4604af 1 LTM4604A ABSOLUTE MAXIMUM RATINGS PIN CONFIGURATION (Note 1) VIN, PGOOD ................................................. –0.3V to 6V COMP, RUN/SS, FB, TRACK..........................–0.3V to VIN SW, VOUT ........................................–0.3V to (VIN + 0.3V) Internal Operating Temperature Range (Note 2) ............................................. –40°C to 125°C Storage Temperature Range................... –55°C to 125°C A B TOP VIEW TRACK PGOOD C F D E G VIN COMP 1 2 RUN/ SS SW 3 FB GND 4 5 6 7 8 9 10 11 GND VOUT LGA PACKAGE 66-PIN (15mm × 9mm × 2.3mm) 0.630mm PAD TJMAX = 125°C, θJA = 25°C/W, θJP = 7°C/W, θJC = 50°C/W, WEIGHT = 1.0g ORDER INFORMATION LEAD FREE FINISH TRAY PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE (NOTE 2) LTM4604AEV#PBF LTM4604AEV#PBF LTM4604AV 66-Lead (15mm × 9mm × 2.3mm) LGA –40°C to 125°C LTM4604AIV#PBF LTM4604AIV#PBF LTM4604AV 66-Lead (15mm × 9mm × 2.3mm) LGA –40°C to 125°C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ This product is only offered in trays. For more information go to: http://www.linear.com/packaging/ ELECTRICAL CHARACTERISTICS The ● denotes the specifications which apply over the full internal operating temperature range, otherwise specifications are at TA = 25°C. VIN = 5V unless otherwise noted. See Figure 15. SYMBOL VIN(DC) VOUT(DC) PARAMETER Input DC Voltage Output Voltage, Total Variation with Line and Load Input Specifications Undervoltage Lockout VIN(UVLO) Threshold Peak Input Inrush Current at IINRUSH(VIN) Start-Up IQ(VIN NOLOAD) Input Supply Bias Current CONDITIONS ● RFB = 5.69k VIN = 2.375V to 5.5V, IOUT = 0A to 4A (Note 3) IOUT = 0A IOUT = 0A, CIN = 10μF, COUT = 22μF ×3, RUN/SS = 0.01μF, VOUT = 1.5V VIN = 3.3V VIN = 5V VIN = 3.3V, No Switching VIN = 3.3V, VOUT = 1.5V, Switching Continuous VIN = 5V, No Switching VIN = 5V, VOUT = 1.5V, Switching Continuous Shutdown, RUN = 0, VIN = 5V ● MIN 2.375 1.482 1.474 TYP 1.5 1.5 MAX 5.5 1.518 1.522 1.75 2 2.3 0.7 0.7 60 28 100 35 7 UNITS V V V V A A μA mA μA mA μA 4604af 2 LTM4604A ELECTRICAL CHARACTERISTICS The ● denotes the specifications which apply over the full internal operating temperature range, otherwise specifications are at TA = 25°C. VIN = 5V unless otherwise noted. See Figure 15. SYMBOL IS(VIN) PARAMETER Input Supply Current Output Specifications IOUT(DC) Output Continuous Current Range (Note 3) Line Regulation Accuracy ΔVOUT(LINE) VOUT ΔVOUT(LOAD) Load Regulation Accuracy VOUT VOUT(AC) fS ΔVOUT(START) tSTART Output Ripple Voltage Output Ripple Voltage Frequency Turn-On Overshoot Turn-on Time ΔVOUT(LS) Peak Deviation for Dynamic Load Step tSETTLE IOUT(PK) Settling Time for Dynamic Load Step Output Current Limit Control Section VFB Voltage at FB Pin IFB VRUN ITRACK V TRACK(OFFSET) V TRACK(RANGE) RFBHI PGOOD ΔVPGOOD RPGOOD RUN Pin On/Off Threshold TRACK Pin Current Offset Voltage Tracking Input Range Resistor Between VOUT and FB Pins PGOOD Range PGOOD Resistance CONDITIONS VIN = 2.5V, VOUT = 1.5V, IOUT = 4A VIN = 3.3V, VOUT = 1.5V, IOUT = 4A VIN = 5V, VOUT = 1.5V, IOUT = 4A MIN TYP 2.9 2.2 1.45 VIN = 3.3V, VOUT = 1.5V VOUT = 1.5V, VIN from 2.375V to 5.5V, IOUT = 0A VOUT = 1.5V, 0A to 4A (Note 3) VIN = 3.3V VIN = 5V IOUT = 0A VIN = 3.3V, VOUT = 1.5V VIN = 5V, VOUT = 1.5V IOUT = 4A, VIN = 5V, VOUT = 1.5V A 0.2 % ● ● 0.3 0.3 0.6 0.6 % % 10 12 1.25 ● 0.793 0.788 TRACK = 0.4V 0 4.975 Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTM4604AE is guaranteed to meet performance specifications over the 0°C to 125°C internal operating temperature range. Specifications over the full –40°C to 125°C internal operating temperature range are assured 4 0.1 0.5 Open-Drain Pull-Down UNITS A A A ● VOUT = 1.5V, RUN/SS = 10nF, IOUT = 0A VIN = 3.3V VIN = 5V VOUT = 1.5V, IOUT = 1A Resistive Load, TRACK = VIN and RUN/SS = Float VIN = 3.3V VIN = 5V Load: 0% to 50% to 0% of Full Load, COUT = 22μF ×3 Ceramic VIN = 5V, VOUT = 1.5V Load: 0% to 50% to 0% of Full Load VIN = 5V, VOUT = 1.5V VIN = 3.3V, VOUT = 1.5V VIN = 5V, VOUT = 1.5V IOUT = 0A, VOUT = 1.5V MAX mVP-P mVP-P MHz 20 20 mV mV 1.5 1.0 ms ms 25 mV 10 8 8 μs A A 0.8 0.8 0.2 0.65 0.2 30 0.807 0.808 4.99 0.8 5.025 V V μA V μA mV V kΩ ±7.5 90 150 % Ω 0.8 by design, characterization and correlation with statistical process controls. The LTM4604AI is guaranteed to meet specifications over the full internal operating temperature range. Note that the maximum ambient temperature is determined by specific operating conditions in conjunction with board layout, the rated package thermal resistance and other environmental factors. Note 3: See output current derating curves for different VIN, VOUT and TA. 4604af 3 LTM4604A TYPICAL PERFORMANCE CHARACTERISTICS Efficiency vs Output Current VIN = 2.5V Efficiency vs Output Current VIN = 3.3V Efficiency vs Output Current VIN = 5V 95 95 90 90 90 85 80 75 65 0 1 85 80 VOUT = 2.5V VOUT = 1.8V VOUT = 1.5V VOUT = 1.2V VOUT = 0.8V 75 VOUT = 1.8V VOUT = 1.5V VOUT = 1.2V VOUT = 0.8V 70 EFFICIENCY (%) 95 EFFICIENCY (%) 100 EFFICIENCY (%) 100 70 65 2 3 OUTPUT CURRENT (A) 0 4 1 65 2 3 OUTPUT CURRENT (A) VOUT (V) 2.5 0 4 4 Load Transient Response ILOAD 2A/DIV ILOAD 2A/DIV 2.0 1 2 3 OUTPUT CURRENT (A) 4604A G03 Load Transient Response VOUT = 3.3V VOUT = 2.5V VOUT = 1.8V VOUT = 1.5V VOUT = 1.2V VOUT = 0.8V VOUT = 3.3V VOUT = 2.5V VOUT = 1.8V VOUT = 1.5V VOUT = 1.2V VOUT = 0.8V 75 4604A G02 Minimum Input Voltage at 4A Load 3.0 80 70 4604A G01 3.5 85 VOUT 20mV/DIV VOUT 20mV/DIV 1.5 1.0 VIN = 5V 20μs/DIV VOUT = 1.2V COUT = 4 × 22μF, 6.3V CERAMICS 0.5 VIN = 5V 20μs/DIV VOUT = 1.5V COUT = 4 × 22μF, 6.3V CERAMICS 4604A G05 4604A G06 0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 VIN (V) 4604A G04 Load Transient Response Load Transient Response Load Transient Response ILOAD 2A/DIV ILOAD 2A/DIV VOUT 20mV/DIV ILOAD 2A/DIV VOUT 20mV/DIV VOUT 20mV/DIV 20µs/DIV VIN = 5V VOUT = 1.8V COUT = 3 × 22µF, 6.3V CERAMICS 4604A G07 VIN = 5V 20µs/DIV VOUT = 2.5V COUT = 3 × 22µF, 6.3V CERAMICS 4604A G08 VIN = 5V 20µs/DIV VOUT = 3.3V COUT = 2 × 22µF, 6.3V CERAMICS 4604A G09 4604af 4 LTM4604A TYPICAL PERFORMANCE CHARACTERISTICS Start-Up Start-Up VOUT 1V/DIV VOUT 1V/DIV IIN 1A/DIV IIN 1A/DIV VIN = 5V 200µs/DIV VOUT = 2.5V COUT = 4 × 22µF NO LOAD (0.01µF SOFT-START CAPACITOR) 4604A G10 VIN = 5V 200μs/DIV VOUT = 2.5V COUT = 4 × 22μF 4A LOAD (0.01μF SOFT-START CAPACITOR) VFB vs Temperature 4604A G11 Current Limit Foldback 806 1.6 1.4 804 1.2 1.0 VOUT (V) VFB (mV) 802 800 0.8 0.6 798 VOUT = 1.5V VIN = 5V 0.2 VIN = 3.3V VIN = 2.5V 0 4 5 3 0.4 796 794 –50 –25 0 25 50 75 TEMPERATURE (°C) 100 125 7 6 OUTPUT CURRENT (A) 4604A G12 4604A G15 Short-Circuit Protection 1.5V Short, No Load Short-Circuit Protection 1.5V Short, 4A Load VOUT 0.5V/DIV VOUT 0.5V/DIV IIN 4A/DIV IIN 1A/DIV 20μs/DIV 8 4604A G13 100μs/DIV 4604A G14 4604af 5 LTM4604A PIN FUNCTIONS VIN (B1, C1, C3-C7, D7, E6 and E7): Power Input Pins. Apply input voltage between these pins and GND pins. Recommend placing input decoupling capacitance directly between VIN pins and GND pins. with an additional resistor between FB and GND pins. Two power modules can current share when this pin is connected in parallel with the adjacent module’s FB pin. See Applications Information section. VOUT (D8-D11, E8-E11, F6-F11, G6-G11): Power Output Pins. Apply output load between these pins and GND pins. Recommend placing output decoupling capacitance directly between these pins and GND pins. Review Table 4. COMP (G1): Current Control Threshold and Error Amplifier Compensation Point. The current comparator threshold increases with this control voltage. Two power modules can current share when this pin is connected in parallel with the adjacent module’s COMP pin. GND (G3-G5, F3-F5, E4-E5, A1-A11, B6-B11, C8-C11): Power Ground Pins for Both Input and Output Returns. PGOOD (F1): Output Voltage Power Good Indicator. Opendrain logic output that is pulled to ground when the output voltage is not within ±7.5% of the regulation point. TRACK (E1): Output Voltage Tracking Pin. When the module is configured as a master output, then a soft-start capacitor is placed on the RUN/SS pin to ground to control the master ramp rate. Slave operation is performed by putting a resistor divider from the master output to ground, and connecting the center point of the divider to this pin on the slave regulator. If tracking is not desired, then connect the TRACK pin to VIN. Load current must be present for tracking. See Applications Information section. FB (G2): The Negative Input of the Error Amplifier. Internally, this pin is connected to VOUT with a 4.99k precision resistor. Different output voltages can be programmed RUN/SS (D1): Run Control and Soft-Start Pin. A voltage above 0.8V will turn on the module, and below 0.5V will turn off the module. This pin has a 1M resistor to VIN and a 1000pF capacitor to GND. See Application Information section for soft-start information. The shut down pin should be pull low with a falling edge of ≤ 1μs to ensure the device does not transition slowly through the internal under voltage lockout threshold. SW (B3 and B4): Switching Node of the circuit is used for testing purposes. This can be connected to copper on the board to improve thermal performance. Make sure not to connect it to other output pins. 4604af 6 LTM4604A BLOCK DIAGRAM PGOOD VIN RSS 1M RUN/SS CSSEXT TRACK SUPPLY 4.99k 10μF 6.3V ×2 10μF 6.3V VIN 2.375V TO 5.5V CSS 1000pF M1 TRACK VOUT L CONTROL, DRIVE 5.76k COMP C2 470pF M2 R1 4.99k 22μF 6.3V ×3 10μF 6.3V INTERNAL COMP VOUT 1.5V 4A GND 4604A BD FB RFB 5.76k SW Figure 1. Simplified LTM4604A Block Diagram DECOUPLING REQUIREMENTS TA = 25°C. Use Figure 1 Configuration. SYMBOL PARAMETER CONDITIONS MIN CIN External Input Capacitor Requirement (VIN = 2.375V to 5.5V, VOUT = 1.5V) IOUT = 4A 10 COUT External Output Capacitor Requirement IOUT = 4A (VIN = 2.375V to 5.5V, VOUT = 1.5V) 22 TYP MAX UNITS μF 100 μF 4604af 7 LTM4604A OPERATION Power Module Description The LTM4604A is a standalone non-isolated switch mode DC/DC power supply. It can deliver up to 4A of DC output current with few external input and output capacitors. This module provides a precise regulated output voltage programmable via one external resistor from 0.8V DC to 5.0V DC over a 2.375V to 5.5V input voltage. A typical application schematic is shown in Figure 15. The LTM4604A has an integrated constant frequency current mode regulator with built-in power MOSFETs with fast switching speed. The typical switching frequency is 1.25MHz. With current mode control and internal feedback loop compensation, the LTM4604A module has sufficient stability margins and good transient performance under a wide range of operating conditions and with a wide range of output capacitors, even all ceramic output capacitors. Current mode control provides cycle-by-cycle fast current limit. In addition, foldback current limiting is provided in an overcurrent condition while VOUT drops. Internal overvoltage and undervoltage comparators pull the open- drain PGOOD output low if the output feedback voltage exits a ±7.5% window around the regulation point. Furthermore, in an overvoltage condition, internal top FET M1 is turned off and bottom FET M2 is turned on and held on until the overvoltage condition clears. Pulling the RUN pin below 0.5V forces the controller into its shutdown state, turning off both M1 and M2. At low load current, the module works in continuous current mode by default to achieve minimum output voltage ripple. The TRACK pin is used for power supply tracking. See the Applications Information section. The LTM4604A is internally compensated to be stable over a wide operating range. Table 4 provides a guideline for input and output capacitance for several operating conditions. An excel loop analysis tool is provided for transient and stability analysis. The FB pin is used to program the output voltage with a single resistor connected to ground. 4604af 8 LTM4604A APPLICATIONS INFORMATION A typical LTM4604A application circuit is shown in Figure 15. External component selection is primarily determined by the maximum load current and output voltage. Refer to Table 4 for specific external capacitor requirements for a particular application. Without considering the inductor current ripple, the RMS current of the input capacitor can be estimated as: VIN to VOUT Step-Down Ratios In the above equation, η% is the estimated efficiency of the power module. The bulk capacitor can be a switcherrated electrolytic aluminum capacitor, OS-CON capacitor for bulk input capacitance due to high inductance traces or leads. If a low inductance plane is used to power the device, then no input capacitance is required. The two internal 10μF ceramics are typically rated for 2A to 3A of RMS ripple current. The worst-case ripple current for the 4A maximum current is 2A or less. There are restrictions in the maximum VIN and VOUT stepdown ratio that can be achieved for a given input voltage. The LTM4604A is 100% duty cycle, but the VIN to VOUT minimum dropout is a function of the load current. A typical 0.5V minimum is sufficient (see Typical Performance Characteristics). Output Voltage Programming The PWM controller has an internal 0.8V reference voltage. As shown in the Block Diagram, a 4.99k 0.5% internal feedback resistor connects the VOUT and FB pins together. The output voltage will default to 0.8V with no feedback resistor. Adding a resistor RFB from the FB pin to GND programs the output voltage: VOUT = 0.8 V • 4.99k + RFB RFB Table 1. FB Resistor vs Output Voltage VOUT 0.8V 1.2V 1.5V 1.8V 2.5V 3.3V RFB Open 10k 5.76k 4.02k 2.37k 1.62k Input Capacitors The LTM4604A module should be connected to a low acimpedance DC source. Two 10μF ceramic capacitors are included inside the module. Additional input capacitors are only needed if a large load step is required up to a full 4A level. An input 47μF bulk capacitor is only needed if the input source impedance is compromised by long inductive leads or traces. For a buck converter, the switching duty cycle can be estimated as: D= VOUT VIN ICIN(RMS) = IOUT(MAX) η% • D • (1– D) Output Capacitors The LTM4604A is designed for low output voltage ripple. The bulk output capacitors defined as COUT are chosen with low enough effective series resistance (ESR) to meet the output voltage ripple and transient requirements. COUT can be a low ESR tantalum capacitor, a low ESR polymer capacitor or an X5R/X7R ceramic capacitor. The typical output capacitance range is 22μF to 100μF. Additional output filtering may be required by the system designer if further reduction of output ripple or dynamic transient spike is required. Table 4 shows a matrix of different output voltages and output capacitors to minimize the voltage droop and overshoot during a 2A/μs transient. The table optimizes the total equivalent ESR and total bulk capacitance to maximize transient performance. The Linear Technology μModule Power Design Tool can be provided for further optimization. Fault Conditions: Current Limit and Overcurrent Foldback The LTM4604A has current mode control, which inherently limits the cycle-by-cycle inductor current not only in steady-state operation, but also in transient. To further limit current in the event of an overload condition, the LTM4604A provides foldback current limiting as the output voltage falls. The LTM4604A device has overtemperature shutdown protection that inhibits switching operation around 150°C. 4604af 9 LTM4604A APPLICATIONS INFORMATION Run Enable and Soft-Start The RUN/SS pin provides dual functions of enable and soft-start control. The RUN/SS pin is used to control turn on of the LTM4604A. While this pin is below 0.5V, the LTM4604A will be in a 7μA low quiescent current state. A 0.8V threshold will enable the LTM4604A. This pin can be used to sequence LTM4604A devices. The soft-start control is provided by a 1M pull-up resistor (RSS) and a 1000pF capacitor (CSS) as drawn in the Block Diagram. An external capacitor can be applied to the RUN/SS pin to increase the soft-start time. A typical value is 0.01μF. The approximate equation for soft-start is: V IN t SOFTSTART = ln • RSS (CSS + CSSEXT ) VIN – 1.8V where RSS and CSS are shown in the Block Diagram of Figure 1, 1.8V is the soft-start upper range, and CSSEXT is the additional capacitance for further soft-start contol. The soft-start function can also be used to control the output ramp-up time, so that another regulator can be easily tracked. An independent ramp control signal can be applied to the master ramp, otherwise, connect the TRACK pin to VIN to disable tracking. pin must go beyond 0.8V to ensure the slave output has reached its final value. Load current must be present for proper tracking. VIN 5V CIN1 10μF 6.3V X5R OR X7R VIN PGOOD LTM4604A COMP FB RUN/SS TRACK GND CSSEXT RAMP CONTROL OR VIN CIN2 10μF 6.3V X5R OR X7R VIN PGOOD LTM4604A COMP FB RUN/SS TRACK GND RFB2 •V 4.99k + RFB2 MASTER V TRACK is the track ramp applied to the slave’s TRACK pin. V TRACK applies the track reference for the slave output up to the point of the programmed value at which V TRACK proceeds beyond the 0.8V reference value. The V TRACK VSLAVE 1.5V 4A VOUT RFB2 5.76k RFB 5.76k COUT2 22μF 6.3V ×3 X5R OR X7R RFB1 4.99k 4604A F02 Figure 2. Dual Outputs (3.3V and 1.5V) with Tracking MASTER OUTPUT OUTPUT VOLTAGE (V) VTRACK = RFB3 1.62k COUT1 22μF 6.3V ×3 X5R OR X7R VIN 5V Output Voltage Tracking Output voltage tracking can be programmed externally using the TRACK pin. The output can be tracked up and down with another regulator. The master regulator’s output is divided down with an external resistor divider that is the same as the slave regulator’s feedback divider to implement coincident tracking. The LTM4604A uses a very accurate 4.99k resistor for the top feedback resistor. Figure 2 shows an example of coincident tracking. VMASTER 3.3V 4A VOUT SLAVE OUTPUT TIME 4604A F03 Figure 3. Output Voltage Coincident Tracking 4604af 10 LTM4604A APPLICATIONS INFORMATION Ratio metric modes of tracking can be achieved by selecting different resistor values to change the output tracking ratio. The master output must be greater than the slave output for the tracking to work. Linear Technology Tracker Cad26 can be used to implement different tracking scenarios. The Master and Slave data inputs can be used to implement the correct resistor values for coincident or ratio tracking. The master and slave regulators require load current for tracking down. The LTM4604A device is an inherently current mode controlled device. Parallel modules will have very good current sharing. This will balance the thermals on the design. Figure 16 shows a schematic of the parallel design. The voltage feedback changes with the variable N as more modules are paralleled. The equation: VOUT Power Good The PGOOD pin is an open-drain pin that can be used to monitor valid output voltage regulation. This pin monitors a ±7.5% window around the regulation point. COMP Pin The pin is the external compensation pin. The module has already been internally compensated for all output voltages. Table 4 is provided for most application requirements. The Linear Technology μModule Power Design Tool can be provided for other control loop optimizations. 4.99k + RFB = 0.8 V • N RFB N is the number of paralleled modules. Thermal Considerations and Output Current Derating The power loss curves in Figures 4 and 5 can be used in coordination with the load derating curves in Figures 6 through 13 for calculating an approximate θJA for the module with and without heat sinking methods with various airflow conditions. Thermal models are derived from several temperature measurements at the bench, and are correlated with thermal analysis software. Tables 2 and 3 provide a summary of the equivalent θJA for the noted conditions. These equivalent θJA parameters are correlated to the measured values and improve with air flow. The maximum junction temperature is monitored while the derating curves are derived. 2.0 2.0 1.8 1.8 1.6 1.6 1.4 1.4 1.2 1.2 WATTS WATTS Parallel Operation 1.0 0.8 1.0 0.8 0.6 0.6 5V TO 1.2V POWER LOSS 3.3V TO 1.2V POWER LOSS 0.4 0.2 0 0 1 3 2 LOAD CURRENT (A) 4 0.2 0 5 4604A F04 Figure 4. 1.2V Power Loss 5V TO 2.5V POWER LOSS 3.3V TO 2.5V POWER LOSS 0.4 0 1 2 3 LOAD CURRENT (A) 4 5 4604A F05 Figure 5. 2.5V Power Loss 4604af 11 LTM4604A 4.0 4.0 3.5 3.5 3.0 3.0 LOAD CURRENT (A) LOAD CURRENT (A) APPLICATIONS INFORMATION 2.5 2.0 1.5 1.0 2.0 1.5 1.0 0LFM 200LFM 400LFM 0.5 0 2.5 70 75 0LFM 200LFM 400LFM 0.5 0 80 85 90 95 100 105 110 115 AMBIENT TEMPERATURE (°C) 70 75 80 85 90 95 100 105 110 115 AMBIENT TEMPERATURE (°C) 4606A F07 Figure 6. 5VIN to 1.2VOUT No Heat Sink Figure 7. 5VIN to 1.2VOUT with Heat Sink 4.0 4.0 3.5 3.5 3.0 3.0 LOAD CURRENT (A) LOAD CURRENT (A) 4606A F06 2.5 2.0 1.5 2.0 1.5 1.0 1.0 0LFM 200LFM 400LFM 0.5 0 2.5 70 75 0LFM 200LFM 400LFM 0.5 80 85 90 95 100 105 110 115 AMBIENT TEMPERATURE (°C) 4606A F08 Figure 8. 3.3VIN to 1.2VOUT No Heat Sink 0 70 75 80 85 90 95 100 105 110 115 AMBIENT TEMPERATURE (°C) 4606A F09 Figure 9. 3.3VIN to 1.2VOUT with Heat Sink 4604af 12 LTM4604A 4.0 4.0 3.5 3.5 3.0 3.0 LOAD CURRENT (A) LOAD CURRENT (A) APPLICATIONS INFORMATION 2.5 2.0 1.5 2.5 2.0 1.5 1.0 1.0 0LFM 200LFM 400LFM 0.5 0 70 75 0LFM 200LFM 400LFM 0.5 0 80 85 90 95 100 105 110 AMBIENT TEMPERATURE (°C) 70 75 80 85 90 95 100 105 110 115 AMBIENT TEMPERATURE (°C) 4606A F10 Figure 11. 5VIN to 2.5VOUT with Heat Sink 4.0 4.0 3.5 3.5 3.0 3.0 LOAD CURRENT (A) LOAD CURRENT (A) Figure 10. 5VIN to 2.5VOUT No Heat Sink 4606A F11 2.5 2.0 1.5 2.0 1.5 1.0 1.0 0LFM 200LFM 400LFM 0.5 0 2.5 70 75 0LFM 200LFM 400LFM 0.5 80 85 90 95 100 105 110 115 AMBIENT TEMPERATURE (°C) 4606A F12 Figure 12. 3.3VIN to 2.5VOUT No Heat Sink 0 70 75 80 85 90 95 100 105 110 115 AMBIENT TEMPERATURE (°C) 4606A F13 Figure 13. 3.3VIN to 2.5VOUT with Heat Sink 4604af 13 LTM4604A APPLICATIONS INFORMATION Table 2. 1.2V Output DERATING CURVE VIN (V) POWER LOSS CURVE AIR FLOW (LFM) HEAT SINK θJA (°C/W) Figures 6, 8 3.3, 5 Figure 4 0 None 25 Figures 6, 8 3.3, 5 Figure 4 200 None 22.5 Figures 6, 8 3.3, 5 Figure 4 400 None 21 Figures 7, 9 3.3, 5 Figure 4 0 BGA Heat Sink 21 Figures 7, 9 3.3, 5 Figure 4 200 BGA Heat Sink 20 Figures 7, 9 3.3, 5 Figure 4 400 BGA Heat Sink 18 DERATING CURVE VIN (V) POWER LOSS CURVE AIR FLOW (LFM) HEAT SINK θJA (°C/W) Figures 10, 12 3.3, 5 Figure 5 0 None 25 Table 3. 2.5V Output Figures 10, 12 3.3, 5 Figure 5 200 None 21 Figures 10, 12 3.3, 5 Figure 5 400 None 21 Figures 11, 13 3.3, 5 Figure 5 0 BGA Heat Sink 21 Figures 11, 13 3.3, 5 Figure 5 200 BGA Heat Sink 18 Figures 11, 13 3.3, 5 Figure 5 400 BGA Heat Sink 16 Table 4. Output Voltage Response Versus Component Matrix (Refer to Figure 17), 0A to 2A Load Step Typical Measured Values CIN VOUT (V) (CERAMIC) CIN (BULK) COUT (CERAMIC) CCOMP VIN (V) DROOP (mV) PEAK-TOPEAK(mV) RECOVERY LOAD STEP (μs) (A/μs) RFB (kΩ) 1.2 10μF 56μF Aluminum 100μF 6.3V None 2.5 21 43 10 2 10 1.2 10μF 56μF Aluminum 22μF ×4 None 3.3 23 45 10 2 10 1.2 10μF 56μF Aluminum 22μF ×4 None 5 24 46 10 2 10 1.5 10μF 56μF Aluminum 100μF 6.3V None 2.5 19 41 10 2 5.76 1.5 10μF 56μF Aluminum 22μF ×4 None 3.3 21 43 10 2 5.76 1.5 10μF 56μF Aluminum 22μF ×4 None 5 21 43 10 2 5.76 1.8 10μF 56μF Aluminum 100μF 6.3V None 2.5 25 50 10 2 4.02 1.8 10μF 56μF Aluminum 22μF ×3 None 3.3 30 60 10 2 4.02 1.8 10μF 56μF Aluminum 22μF ×3 None 5 30 60 10 2 4.02 2.5 10μF 56μF Aluminum 100μF 6.3V None 2.5 22 45 12 2 2.37 2.5 10μF 56μF Aluminum 22μF ×3 None 3.3 25 55 12 2 2.37 2.5 10μF 56μF Aluminum 22μF ×3 None 5 25 55 12 2 2.37 3.3 10μF 56μF Aluminum 100μF 6.3V None 2.5 22 50 15 2 1.62 3.3 10μF 56μF Aluminum 22μF ×3 None 3.3 25 56 15 2 1.62 3.3 10μF 56μF Aluminum 22μF ×3 None 5 25 56 15 2 1.62 4604af 14 LTM4604A APPLICATIONS INFORMATION Safety Considerations The LTM4604A modules do not provide isolation from VIN to VOUT. There is no internal fuse. If required, a slow blow fuse with a rating twice the maximum input current needs to be provided to protect each unit from catastrophic failure. Layout Checklist/Example The high integration of LTM4604A makes the PCB board layout very simple and easy. However, to optimize its electrical and thermal performance, some layout considerations are still necessary. • Use large PCB copper areas for high current path, including VIN, GND and VOUT. It helps to minimize the PCB conduction loss and thermal stress. GND • Place high frequency ceramic input and output capacitors next to the VIN, GND and VOUT pins to minimize high frequency noise. • Place a dedicated power ground layer underneath the unit. • To minimize the via conduction loss and reduce module thermal stress, use multiple vias for interconnection between top layer and other power layers. • Do not put vias directly on the pads unless they are capped. • SW pads can be soldered to board to improve thermal performance. Figure 14 gives a good example of the recommended layout. VIN 2.375V TO 5.5V VOUT CIN 10μF 6.3V X5R OR X7R COUT COUT OPEN-DRAIN PULL UP VIN PGOOD VOUT 1.5V 4A VOUT LTM4604A COUT COMP FB RUN/SS TRACK CSSEXT 0.01μF GND RFB 5.69k COUT 22μF ×3 6.3V X5R OR X7R 4604A F15 Figure 15. Typical 2.375V to 5.5V Input, 1.5V at 4A Design VIN CIN GND 4604A F14 Figure 14. Recommended PCB Layout 4604af 15 LTM4604A TYPICAL APPLICATIONS VIN 2.375V TO 5V CIN1 10μF 6.3V X5R OR X7R OPEN-DRAIN PULL UP VOUT = 0.8V × ((4.99k/N) + RFB)/RFB WHERE N IS THE NUMBER OF PARALLEL MODULES VIN PGOOD VOUT COUT1 22μF ×3 6.3V X5R OR X7R REFER TO TABLE 4 LTM4604A COMP FB RUN/SS TRACK CSSEXT 0.01μF GND RFB 2.87k VOUT 1.5V 8A CIN2 10μF 6.3V X5R OR X7R VIN PGOOD VOUT COUT2 22μF ×3 6.3V X5R OR X7R REFER TO TABLE 4 LTM4604A COMP FB RUN/SS TRACK GND 4604A F16 Figure 16. Two LTM4604As in Parallel, 1.5V at 8A Design 4604af 16 LTM4604A TYPICAL APPLICATIONS VIN 3.3V TO 5V CIN 10μF 6.3V X5R OR X7R 50k VIN OPEN-DRAIN PULL UP PGOOD VOUT 2.5V 4A VOUT LTM4604A COMP FB RUN/SS TRACK CSSEXT 0.01μF GND RFB 2.37k COUT 22μF ×3 6.3V X5R OR X7R REFER TO TABLE 4 4604A F17 Figure 17. 3.3V to 5V Input, 2.5V at 4A Design 4604af 17 LTM4604A PACKAGE DESCRIPTION LGA Package 66-Lead (15mm × 9mm × 2.32mm) (Reference LTC DWG # 05-08-1820 Rev Ø) DETAIL A 2.19 – 2.45 G aaa Z F E D C B PAD 1 A 1 PAD “A1” CORNER 2 4 3 4 5 15.00 BSC 12.70 BSC MOLD CAP 6 SUBSTRATE 7 0.290 – 0.350 8 1.90 – 2.10 9 Z // bbb Z DETAIL B 10 11 0.630 ±0.025 SQ. 68x X aaa Z 9.00 BSC eee S X Y Y 7.620 BSC DETAIL B PADS SEE NOTES 3 PACKAGE BOTTOM VIEW 3.810 2.540 1.270 0.000 1.270 2.540 3.810 0.315 0.315 PACKAGE TOP VIEW 1.27 BSC DETAIL A 6.350 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994 5.080 2. ALL DIMENSIONS ARE IN MILLIMETERS 3.810 3 LAND DESIGNATION PER JESD MO-222 4 DETAILS OF PAD #1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED WITHIN THE ZONE INDICATED. THE PAD #1 IDENTIFIER MAY BE EITHER A MOLD OR MARKED FEATURE 2.540 1.270 0.000 1.270 2.540 3.810 5.080 6.350 0.315 0.315 5. PRIMARY DATUM -Z- IS SEATING PLANE 6. THE TOTAL NUMBER OF PADS: 66 SYMBOL TOLERANCE aaa 0.15 bbb 0.10 eee 0.05 COMPONENT PIN “A1” LTMXXXXXX μModule TRAY PIN 1 BEVEL PACKAGE IN TRAY LOADING ORIENTATION LGA 66 0108 REV Ø SUGGESTED PCB LAYOUT TOP VIEW 4604af 18 LTM4604A PACKAGE DESCRIPTION Pin Assignment Table (Arranged by Pin Number) PIN NAME PIN NAME PIN NAME PIN NAME PIN NAME PIN NAME PIN NAME A1 GND B1 VIN C1 VIN D1 RUN/SS E1 TRACK F1 PGOOD G1 A2 GND B2 – C2 – D2 – E2 – F2 – G2 COMP FB A3 GND B3 SW C3 VIN D3 – E3 – F3 GND G3 GND A4 GND B4 SW C4 VIN D4 – E4 GND F4 GND G4 GND A5 GND B5 – C5 VIN D5 – E5 GND F5 GND G5 GND A6 GND B6 GND C6 VIN D6 – E6 VIN F6 VOUT G6 VOUT A7 GND B7 GND C7 VIN D7 VIN E7 VIN F7 VOUT G7 VOUT A8 GND B8 GND C8 GND D8 VOUT E8 VOUT F8 VOUT G8 VOUT A9 GND B9 GND C9 GND D9 VOUT E9 VOUT F9 VOUT G9 VOUT A10 GND B10 GND C10 GND D10 VOUT E10 VOUT F10 VOUT G10 VOUT A11 GND B11 GND C11 GND D11 VOUT E11 VOUT F11 VOUT G11 VOUT 4604af Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 19 LTM4604A PACKAGE PHOTOGRAPH RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC2900 Quad Supply Monitor with Adjustable Reset Timer Monitors Four Supplies; Adjustable Reset Timer LTC2923 Power Supply Tracking Controller LTM4600HV 10A DC/DC μModule Tracks Both Up and Down; Power Supply Sequencing 4.5V ≤ VIN ≤ 28V; 0.6V ≤ VOUT ≤ 5V; 15mm × 15mm × 2.8mm LTM4601/LTM4601A 12A DC/DC μModule with PLL, Output Tracking/ Margining and Remote Sensing Synchronizable, PolyPhase Operation, LTM4601-1/LTM4601A-1 Version has no Remote Sensing LTM4601AHVMP 12A Military Grade μModule 4.5V ≤ VIN ≤ 28V; 0.6V ≤ VOUT ≤ 5V; 15mm × 15mm × 2.8mm, –55°C to 125°C LTM4602 6A DC/DC μModule Pin Compatible with the LTM4600 LTM4603 6A DC/DC μModule with PLL and Output Tracking/ Synchronizable, PolyPhase Operation, LTM4603-1 Version has Margining and Remote Sensing no Remote Sensing, Pin Compatible with the LTM4601 LTM4605 5A Buck-Boost μModule 4.5V ≤ VIN ≤ 20V; 0.8V ≤ VOUT ≤ 16V; 15mm × 15mm × 2.8mm LGA LTM4607 5A Buck-Boost μModule 4.5V ≤ VIN ≤ 36V; 0.8V ≤ VOUT ≤ 24V; 15mm × 15mm × 2.8mm LGA LTM4608A 8A Low Voltage μModule 2.4V ≤ VIN ≤ 5.5V, Parallel for Higher Output Current, 9mm × 15mm × 2.8mm LGA LTM4616 Dual 8A DC/DC μModule Dual 8A or Single 16A; 2.375V ≤ VIN ≤ 5.5V; 15mm × 15mm × 2.5mm LGA LTM8020 0.2A DC/DC μModule 4V ≤ VIN ≤ 36V; 1.25V ≤ VOUT ≤ 5V; 6.25mm × 6.25mm × 2.3mm LGA LTM8021 0.5A DC/DC μModule 3.6V ≤ VIN ≤ 36V; 0.8V ≤ VOUT ≤ 5V; 6.25mm × 11.25mm × 2.8mm LGA LTM8022 1A DC/DC μModule 3.6V ≤ VIN ≤ 36V; 0.8V ≤ VOUT ≤ 10V; 11.25mm × 9mm × 2.8mm LGA LTM8023 2A DC/DC μModule 3.6V ≤ VIN ≤ 36V; 0.8V ≤ VOUT ≤ 10V; 11.25mm × 9mm × 2.8mm LGA 4604af 20 Linear Technology Corporation LT 0808 • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com © LINEAR TECHNOLOGY CORPORATION 2008