Series AMER40-Z up to 900mA | AC-DC LED driver • • • • FEATURES: Constant Current LED Driver High Efficiency: Up to 89% Active Power Factor Correction Short Circuit / Open Circuit Protection • • • • Meet UL, CE Safety Requirement Long Life, High reliability IP65/IP67 design for indoor/outdoor 5 Years Limited Warranty Models Single output Model Max Output Power (W) Output Voltage Range (V) Output Current (mA) Input Voltage (VAC/Hz) Efficiency (%) 31.5 37.8 30-42 30-42 750 900 90-305/47-63 90-305/47-63 89 89 AMER40-4275Z AMER40-4290Z NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity <75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Input Current Inrush current <2ms Conditions 90 VAC, full load 115 VAC, cold start 277 VAC, cold start Typical Leakage current Input dissipation Power Factor No Load Output Short 115 VAC, full load 277 VAC, full load Input Fuse Start-up Time Maximum 0.58 40 60 0.75 1.0 4.5 0.98 0.92 Units Arms 1.5 1.0 Sec. Sec. Maximum Units 2.5 1.5 % % % V p-p A p-p 10 % 0 ms Rated Units 3750 2000 500 VAC A mA W W 2 A / 300 VAC 115 VAC, full load 277 VAC, full load Output Specifications Parameters Current accuracy Line regulation Load regulation Ripple & Noise Output Current Ripple Current Overshoot Conditions Typical LL to HL Full Output Voltage Range ±5 ±3 ±5 Full load, 16.7-20ms duration LL to HL, full load at cold start, % of rated output current Hold-up time (min) Minimum Load Voltage See Models Table Above Isolation Specifications Parameters Tested I/O voltage Isolation Resistance Isolation Capacitance Conditions Typical I/P – O/P I/P – FG O/P – FG I/P – O/P, 500Vdc >100MΩ VAC pF 2500 General Specifications Parameters Switching frequency Over voltage protection Short circuit protection Short circuit restart www.aimtec.com F 052.1e R3 Conditions Typical Maximum Units 50 KHz VDC 150 Hiccup Mode Auto Recovery Tel: +1 514 620 2722 1 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMER40-Z up to 900mA | AC-DC LED driver Open circuit protection Operating temperature Storage temperature Maximum case temperature Temperature coefficient Cooling Humidity Case material Potting material IP Rating Weight Dimensions (L X W+ X H) MTBF Hiccup Mode -40 to +60 -40 to +90 With Derating over oC oC oC 90 0.03 % / oC 90 % RH Free Air Convection Metal (Aluminum) Epoxy (IP67 rated) IP67 430 6.50 X 1.91 X 1.31 inches 165 X 48.6 X 33.3 mm 400,000 hrs (MIL-HDBK-217F at +25°C) g Safety Specifications Parameters Electromagnetic Interference Harmonic Current Emissions Voltage fluctuations and flicker Electrostatic Discharge Immunity RF, Electromagnetic Field Immunity Electrical Fast Transient / Burst Immunity Surge Immunity RF, Conducted Disturbance Immunity Power frequency Magnetic Field Immunity Voltage dips, Short Interruptions Immunity Electromagnetic Immunity Requirements Applies to Lighting Equipment Standards EN55015 / FCC Part 15, Class B EN61000-3-2, Class B EN61000-3-3 EN61000-4-2, 8kV Air, 4kV Contact, Level 3, Criteria A EN61000-4-3, Test-RS Level 3, Criteria A EN61000-4-4, Burst EFT Level 3, Criteria A EN61000-4-5, Line to Neutral 4kV, Line/Neutral to FG 6kV EN61000-4-6. Test-CS Level 3, Criteria A EN61000-4-8, Test 3A/m, Criteria A EN61000-4-11, Criteria B EN61547 Pin Definition Wire Connection Brown Blue Yellow/Green Red Black AC L AC N FG +V Output -V OUtput www.aimtec.com F 052.1e R3 Dimensions Tel: +1 514 620 2722 2 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMER40-Z up to 900mA | AC-DC LED driver Application Block diagram AC_L LED+ FG AC LED- AC_N Efficiency Vs. Input Voltage & Output Voltage AMER40-4275Z 95.00% 90.00% Efficiency 85.00% 115VAC 80.00% 230VAC 75.00% 277VAC 70.00% 65.00% 30 33 36 39 42 Output Voltage(V) AMER40-4290Z 95.00% 90.00% Efficiency 85.00% 80.00% 115VAC 75.00% 230VAC 70.00% 277VAC 65.00% 30 33 36 39 42 Output Voltage(V) www.aimtec.com F 052.1e R3 Tel: +1 514 620 2722 3 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMER40-Z up to 900mA | AC-DC LED driver PF vs. Input Voltage & Output Voltage AMER40-4275Z 1.200 PF 0.900 115VAC 0.600 230VAC 0.300 277VAC 0.000 30 33 36 39 42 Output Voltage(V) AMER40-4290Z 1.200 PF 0.900 115VAC 0.600 230VAC 277VAC 0.300 0.000 30 33 36 39 42 Output Voltage(V) NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5.Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 052.1e R3 Tel: +1 514 620 2722 4 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only