Renesas ISL8272M 50a digital dc/dc pmbus power module Datasheet

DATASHEET
ISL8272M
FN8670
Rev.5.00
Nov 8, 2017
50A Digital DC/DC PMBus Power Module
The ISL8272M is a 50A step-down PMBus compliant digital
power module. Integrated in the module is a high performance
digital PWM controller, dual-phase power MOSFETs, inductors,
and the passives. This high efficiency power module is capable
of delivering 50A without the need for airflow and heatsinks.
The ISL8272M can be placed in a current sharing
configuration with up to four modules in parallel to deliver
200A continuous current.
The ISL8272M operates with the ChargeMode™ control
architecture, which responds to a transient load within a single
switching cycle. The ISL8272M comes with operating in a pin
strap mode; output voltage, switching frequency device, SMBus
address, input UVLO, soft-start/stop, and current sharing can be
programmed through external resistors. More configuration such
as fault limits, fault response, margining, and sequencing can be
easily programmed using the PMBus interface. PMBus can be
used to monitor voltages, currents, temperatures, and fault
status. The ISL8272M is supported by the PowerNavigator™
software, a graphical user interface (GUI) that can be used to
configure modules to a desired solution.
The ISL8272M is built in a compact (18mmx23mmx7.5mm)
and low profile overmolded HDA package, suitable for
automated assembly by standard surface mount equipment.
Features
• Complete digital switch mode power supply
• Wide input voltage range: 4.5V to 14V
• Programmable output voltage range: 0.6V to 5V
• PMBus compliant communication interface
• Programmable VOUT, margining, UV/OV, UC/OC, UT/OT,
soft-start/stop, sequencing and external synchronization
• Monitor of VIN, VOUT, IOUT, temperature, duty cycle, switching
frequency, power-good, and faults
• Fast response ChargeMode control architecture
• Multiphase current sharing with up to four modules
• ±1.0% VOUT accuracy over line, load, and temperature
• Internal nonvolatile memory and fault logging
• Thermally enhanced HDA package
Applications
• Server, telecom, storage, and datacom
• Industrial/ATE and networking equipment
• General purpose power for ASIC, FPGA, DSP, and memory
Related Literature
• For a full list of related documents, visit our website
- ISL8272M product page
VIN
VIN
CIN
VOUT
VDD
VSENP
ENABLE
EN
VOUT
18m
COUT
VSENN
VR5
10µF
10µF
VR6
VDRV
m
23
VR
ISL8272M
m
m
VR55
VCC
SDA
2x10µF
PMBUS
INTERFACE
SALRT
VMON
6.65k 
7.5mm
SCL
VDRV1
100k 
SGND
PGND
NOTE:
1. Figure 1 represents a typical implementation of the ISL8272M. For PMBus
operation, it is recommended to tie the enable pin (EN) to SGND.
FIGURE 1. 50A APPLICATION CIRCUIT
FN8670 Rev.5.00
Nov 8, 2017
FIGURE 2. A SMALL PACKAGE FOR HIGH POWER DENSITY
Page 1 of 59
ISL8272M
Table of Contents
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pin Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ISL8272M Internal Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Typical Application Circuit - Single Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Typical Application Circuit - Three Module Current Sharing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Thermal Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Typical Performance Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Efficiency Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Transient Response Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Derating Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SMBus Communications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Voltage Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Soft-Start/Stop Delay and Ramp Times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Good . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching Frequency and PLL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loop Compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Undervoltage Lockout (UVLO). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SMBus Module Address Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Overvoltage Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Prebias Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Overcurrent Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Thermal Overload Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Digital-DC Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Active Current Sharing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Phase Spreading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fault Spreading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Sequencing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Monitoring with SMBus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Snapshot Parameter Capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Nonvolatile Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
17
17
17
18
18
19
19
19
20
20
20
21
21
21
22
22
23
23
23
23
Layout Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Thermal Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Package Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCB Layout Pattern Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Thermal Vias. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stencil Pattern Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reflow Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
24
24
24
24
24
PMBus Command Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
PMBus Data Formats. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
PMBus Use Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
PMBus Commands Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Firmware Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Revision History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
About Intersil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Package Outline Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
FN8670 Rev.5.00
Nov 8, 2017
Page 2 of 59
ISL8272M
Ordering Information
PART NUMBER
(Notes 2, 3, 4)
PART
MARKING
TEMP RANGE
(°C)
PACKAGE
(RoHS Compliant)
PKG.
DWG. #
ISL8272MAIRZ
ISL8272M
-40 to +85
58 LD 18x23 HDA
Y58.18x23
ISL8272MBIRZ
ISL8272MB
-40 to +85
58 LD 18x23 HDA
Y58.18x23
ISL8272MEVAL1Z
Single-Module Evaluation Board (see UG003, “ISL8272MEVAL1Z Evaluation Board User Guide”)
ISL8272MEVAL2Z
Three-Module Current Sharing Evaluation Board (see UG004, “ISL8272MEVAL2Z Evaluation Board User Guide”)
NOTES:
2. Add “-T” suffix for 100 unit tape and reel option. Refer to TB347 for details on reel specifications.
3. These Intersil Pb-free plastic packaged products are RoHS compliant by EU exemption 7C-I and 7A. They employ special Pb-free material sets; molding
compounds/die attach materials and NiPdAu plate-e4 termination finish, which is compatible with both SnPb and Pb-free soldering operations.
Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD020.
4. For Moisture Sensitivity Level (MSL), refer to the ISL8272M product information page. For more information about MSL, refer to TB363.
ISL
xxxxM
INTERSIL DEVICE DESIGNATOR
BASE PART NUMBER
FIRMWARE REVISION
A: FC01
B: FC02
OPERATING TEMPERATURE
I: INDUSTRIAL (‐ 40°C TO +85°C)
FN8670 Rev.5.00
Nov 8, 2017
F
T
R
Z
S
SHIPPING OPTION
BLANK: BULK
T: TAPE AND REEL
ROHS
Z: ROHS COMPLIANT
PACKAGE DESIGNATOR
R: HIGH DENSITY ARRAY (HDA)
Page 3 of 59
ISL8272M
Pin Configuration
ISL8272M
(58 LD HDA)
TOP VIEW
1
2
3
4
A
TEST
D
E
9
10 11 12 13 14 15 16 17 18
SA
VMON
CS
PAD2
VOUT
MGN
SCL
SALRT SDA
EN
TEST
TEST
PAD6
VSENN VSENP
P
R
T
U
PGND
ASCR V25
SGND
VDD
L
N
PGND
TEST
K
M
TEST
TEST
SYNC
PG
DDC
PAD7
J
8
VOUT
VSET
SS/UVLO
PGND
PGND
PAD5
H
7
PAD4
PAD3
C
G
6
PAD1
B
F
5
VR SWD1
VCC
VR6 SGND
VR55
PAD8
SGND
PGND
VR5
PGND
PGND VDRV
VDRV1
DCM
VIN
PAD9
PAD10
VIN
PGND
SGND
SWD2
VDRV
VDRV1
DCM
PAD11
PAD12
VIN
PGND
SGND
V
W
PGND
SW1
Y
AA
AB
AC
SW2
PGND
PAD15
PAD13
PAD14
PAD16
Pin Descriptions
PIN
LABEL
TYPE
DESCRIPTION
PAD1, 2
VOUT
PWR
Power supply output voltage. Output voltage from 0.6V to 5V. Tie these two pins together to achieve a single output.
For higher output voltage, refer to the derating curves starting on page 15 to set the maximum output current from
these pads.
PAD3, 4, 5, 7,
10, 12, 13, 15
PGND
PWR
Power ground. Refer to “Layout Guide” on page 23 for the PGND pad connections and I/O capacitor placement.
PAD6
SGND
PWR
Signal ground. Refer to “Layout Guide” on page 23 for the SGND pad connections.
PAD8, 9, 11
VIN
PWR
Input power supply voltage to power the module. Input voltage range from 4.5V to 14V.
PAD14, 16
SW1,
SW2
PWR
Switching node pads. The SW pads dissipate the heat and provide good thermal performance. Refer to “Layout
Guide” on page 23 for the SW pad connections.
C6
VSET
I
Output voltage selection pin. Used to set VOUT set point and VOUT max.
C7
CS
I
Current sharing configuration pin. Used to program current sharing configurations such as SYNC selection, phase
spreading, and VOUT droop.
C8
MGN
I
External VOUT margin control pin. Active high (>2V) sets VOUT margin high; active low (<0.8V) sets VOUT margin low;
high impedance (floating) sets VOUT to normal voltage. Factory default range for margining is nominal VOUT ±5%.
When using PMBus to control margin command, leave this pin as no connection.
C9
VMON
I
Driver voltage monitoring. Use this pin to monitor VDRV through an external 16:1 resistor divider.
C10
SA
I
Serial address selection pin. Used to assign unique address for each individual device or to enable certain
management features.
C11
SALRT
O
Serial alert. Connect to external host if desired. SALRT is asserted low upon a warning or a fault event and deasserted
when warning or fault is cleared. A pull-up resistor is required.
FN8670 Rev.5.00
Nov 8, 2017
Page 4 of 59
ISL8272M
Pin Descriptions
(Continued)
PIN
LABEL
TYPE
C12
SDA
I/O
Serial data. Connect to external host and/or to other Digital-DC™ devices. A pull-up resistor is required.
C13
SCL
I/O
Serial clock. Connect to external host and/or to other Digital-DC devices. A pull-up resistor is required.
D4
SS/
UVLO
I
Soft-start/stop and undervoltage lockout selection pin. Used to set turn on/off delay and ramp time as well as input
UVLO threshold levels.
D5
PG
O
Power-good output. Power-good output can be an open drain that requires a pull-up resistor or push-pull output that
can drive a logic input.
D13
SYNC
I/O
Clock synchronization input. Used to set the frequency of the internal switch clock, to sync to an external clock or to
output internal clock.
E14
EN
I
E4
DDC
I/O
C5, D14, E15,
F4, F15, G4
TEST
-
Test pins. Do not connect these pins.
G14
ASCR
I
ChargeMode™ control ASCR parameters selection pin. Used to set ASCR gain and residual values.
G15
V25
PWR
Internal 2.5V reference used to power internal circuitry. No external capacitor required for this pin.
H3
VSENN
I
Differential output voltage sense feedback. Connect to negative output regulation point.
H4
VSENP
I
Differential output voltage sense feedback. Connect to positive output regulation point.
H16, J16, K16,
M14
SGND
PWR
Signal grounds. Using multiple vias to connect the SGND pins to the internal SGND layer.
K14
VDD
PWR
Input supply voltage for controller. Connect VDD pad to VIN supply.
L2
VR
PWR
Internal LDO bias pin. Tie VR to VR55 directly with a short loop trace.
L3, P11
SWD1,
SWD2
PWR
Switching node driving pins. Directly connect to the SW1 and SW2 pads with short loop wires.
L14
VR5
PWR
Internal 5V reference used to power internal circuitry. Place a 10µF decoupling capacitor for this pin.
M1
VCC
PWR
Internal LDO output. Connect VCC to VDRV for internal LDO driving.
M5, M17, N5
PGND
PWR
Power grounds. Using multiple vias to connect the PGND pins to the internal PGND layer.
M10
VR55
PWR
Internal 5.5V bias voltage for internal LDO use only. Tie VR55 pin directly to VR pin.
M13
VR6
PWR
Internal 6V reference used to power internal circuitry. Place a 10µF decoupling capacitor for this pin.
N6, N16
VDRV
PWR
Power supply for internal FET drivers. Connect 10μF bypass capacitor to each of these pins. These pins can be driven
by the internal LDO through VCC pin or by the external power supply directly. Keep the driving voltage between 4.5V
and 5.5V. For 5V input application, use external supply or connect this pin to VIN.
R8, R17
VDRV1
I
FN8670 Rev.5.00
Nov 8, 2017
DESCRIPTION
Enable pin. Logic high to enable the module output.
A Digital-DC bus. This dedicated bus provides the communication between devices for features such as sequencing,
fault spreading and current sharing. The DDC pin on all Digital-DC devices should be connected together. A pull-up
resistor is required.
Bias pin of the internal FET drivers. Always tie to VDRV.
Page 5 of 59
ISL8272M
VDRV1
VDRV
VCC
VIN
VR
VR55
V25
VR5
VR6
VDD
ISL8272M Internal Block Diagram
LDO
LDOs
0.27µH
VOUT
SS
OV/UV
CURRENT SHARE
INTERLEAVE
OC/UC
POWER
MANAGEMENT
SEQUENCE
FAULT SPREADING
MARGINING
PGND
VDRV1
OT/UT
SNAPSHOT
SWD2
SW2
LOGIC
ASCR
CS
VSET
SS/UVLO
EN
DDC
PG
MGN
VDRV
VIN
FILTER
SYNC
OUT
PWM2
SYNC
PLL
D-PWM
PWM1
ChargeMode TM
CONTROL
SUPERVISOR
VIN
VDRV
NVM
SWD1
SW1
ADC
CSA
VDRV1
ADC
0.27µH
LOGIC
PROTECTION
VOUT
CSA
ADC
PGND
VSA
VDD
ADC
INTERNAL
TEMP SENSOR
SCL
SDA
SALRT
PMBus/I2C
INTERFACE
22 
SA
VSENP
VSENN
SGND
22 
PGND
SGND
VMON
DIGITAL CONTROLLER
FIGURE 3. INTERNAL BLOCK DIAGRAM
FN8670 Rev.5.00
Nov 8, 2017
Page 6 of 59
ISL8272M
DDC
SCL
SCL
SDA
SDA
SALRT
PG
CS
VR55
VR
SALRT
470µF
BULK
C1
MGN
Note 5 Note 5 Note 6
DDC
R11 R12
ASCR
R4
R10
SYNC
R3
R9
SS/UVLO
R2
R8
SA
R1
12V
PG
10k  10k  10k  10k 
Note 7 R7
VIN
EN
VAUX OR VCC
3.3V TO 5V
EN
MGN
PIN STRAP RESISTORS
(OPTIONAL)
VSET
FN8670 Rev.5.00
Nov 8, 2017
Typical Application Circuit - Single Module
4x22µF
CERAMIC
C2
SWD1
SW1
VIN
SWD2
C3
VDD
10µF
VR5
10µF
10µF
C4
C5
SW2
ISL8272M
8x100µF
CERAMIC
VR6
4x470µF
POSCAP
VOUT
VDRV
VMON
R6
6.65k 
C8
VDRV1
VSENN
C7
VSENP
C6
VCC
PGND
R5
100k
10µF
SGND
VCC 10µF
Page 7 of 59
NOTES:
5. R2 and R3 are not required if the PMBus host already has I2C pull-up resistors.
6. Only one R4 per DDC bus is required when multiple modules share the same DDC bus.
7. R7 through R12 can be selected according to the tables for the pin-strap resistor setting in this document.
If the PMBus configuration is chosen to overwrite the pin-strap configuration, R8 through R12 can be non-populated.
8. V25, VR and VR55 do not need external capacitors. V25 can be no connection.
FIGURE 4. TYPICAL APPLICATION CIRCUIT - SINGLE MODULE
C9
VOUT
1.2V 50A
ISL8272M
Typical Application Circuit - Three Module Current Sharing
12V
2X470µF
BULK
C1
PG1
PG
R9
R10
R11
SDA
CS
SCL
SDA
ASCR
DDC
SCL
VSET
DDC
SALRT
VIN
R8
R4
SS/UVLO
R3
SA
R2
MGN
51.1k 
R7
R1
EN
4.7k  4.7k  4.7k  4.7k 
EN
SMBus Address= 0x2A
VAUX or VCC
3.3V to 5V
MGN
PIN STRAP RESISTORS
(OPTIONAL)
VR55
VR
SALRT
SYNC
SYNC
4x22µ F
CERAMIC
C2
SWD1
SW1
VIN
C3
SWD2
VDD
10µF
10µF
10µF
C4
C5
SW2
ISL8272M
VR5
4x100µF
CERAMIC
VR6
12x100µ F
CERAMIC
12x470µ F
POSCAP
VOUT
VCC
C8
VSENN
MGN
PG2
PG
SGND
VMON
R6
6.65k 
EN
VDRV1
EN
C7
VSENP
C6
PGND
10µF
VCC1 10µF
R5
100k 
VOUT
1.2V 150A
VDRV
C23
C24
PIN STRAP RESISTORS
(OPTIONAL)
SMBus Address = 0x2B
56.2k 
SCL
MGN
R18
CS
VSET
R17
SS/UVLO
DDC
R16
ASCR
R15
SA
R14
VR55
SDA
VR
SALRT
4x22µF
CERAMIC
C9
SWD1
SYNC
SW1
VIN
C10
SWD2
VDD
10µF
10µF
10µF
SW2
ISL8272M
VR5
4x100µF
CERAMIC
VR6
C12
C11
VOUT
VDRV
VCC
C15
VSENN
MGN
PG3
PG
SGND
VMON
R13
6.65k 
EN
VDRV1
EN
C14
VSENP
C13
10µF
PGND
VCC2 10µF
R12
100k 
PIN STRAP RESISTORS
(OPTIONAL)
SMBus Address = 0x2C
61.9k 
SCL
MGN
R25
CS
R24
ASCR
VSET
R23
SS/UVLO
DDC
R22
SA
R21
VR55
SDA
VR
SALRT
SWD1
SYNC
4x22µF
CERAMIC
C16
SW1
VIN
C17
SWD2
VDD
10µF
10µF
10µF
C18
SW2
ISL8272M
VR5
4x100µF
CERAMIC
VR6
C19
VOUT
VDRV
VCC
C22
VMON
VSENN
VDRV1
VSENP
C21
PGND
R20
6.65k 
C20
10µF
SGND
VCC3 10µF
R19
100k 
FIGURE 5. TYPICAL APPLICATION CIRCUIT - THREE MODULE CURRENT SHARING
FN8670 Rev.5.00
Nov 8, 2017
Page 8 of 59
ISL8272M
TABLE 1. ISL8272M DESIGN GUIDE MATRIX AND OUTPUT VOLTAGE RESPONSE
VIN
(V)
VOUT
(V)
CIN (BULK)
(Note 9)
(µF)
CIN
(CERAMIC)
(µF)
COUT
(BULK)
(µF)
COUT
(CERAMIC)
(µF)
ASCR GAIN
(Note 10)
ASCR
RESIDUAL
(Note 10)
P-P
DEVIATION
(mV)
RECOVERY
TIME
(µs)
LOAD STEP
(A)
(Note 11)
FREQ.
(kHz)
5
1
1x470
6x47
4x470
12x100
220
90
50
20
0/25
300
5
1
1x470
4x47
4x470
8x100
550
100
45
15
0/25
533
12
1
1x470
6x22
4x470
12x100
220
90
55
22
0/25
300
12
1
1x470
4x22
4x470
8x100
550
100
50
15
0/25
533
5
1.8
1x470
6x47
4x470
8x100
200
90
60
25
0/25
300
5
1.8
1x470
4x47
2x470
6x100
250
90
70
20
0/25
533
12
1.8
1x470
6x22
4x470
8x100
220
90
70
20
0/25
300
12
1.8
1x470
4x22
2x470
6x100
280
100
70
20
0/25
533
5
2.5
1x470
6x47
2x470
6x100
120
90
100
30
0/25
300
5
2.5
1x470
4x47
2x470
4x100
250
90
80
20
0/25
533
12
2.5
1x470
6x22
2x470
6x100
110
90
100
20
0/25
300
12
2.5
1x470
4x22
2x470
4x100
220
90
100
15
0/25
533
5
3.3
1x470
6x47
2x470
4x100
100
90
120
50
0/25
300
5
3.3
1x470
4x47
2x470
4x100
220
90
100
30
0/25
533
12
3.3
1x470
4x22
2x470
4x100
220
90
100
10
0/25
533
12
5
1x470
6x22
2x470
4x100
230
90
120
10
0/25
533
NOTES:
9. CIN bulk capacitor is optional only for energy buffer from the long input power supply cable.
10. ASCR gain and residual are selected to ensure phase margin higher than 60° and gain margin higher than 6dB at room temperature and full load
(50A).
11. Output voltage response is tested with load step slew rate higher than 100A/µs.
TABLE 2. RECOMMENDED INPUT/OUTPUT CAPACITOR
VENDORS
VALUE
PART NUMBER
MURATA, Input Ceramic
47µF, 16V, 1210
GRM32ER61C476ME15L
MURATA, Input Ceramic
22µF, 16V, 1210
GRM32ER61E226KE15L
TAIYO YUDEN, Input Ceramic
47µF, 16V, 1210
EMK325BJ476MM-T
TAIYO YUDEN, Input Ceramic
22µF, 25V, 1210
TMK325BJ226MM-T
MURATA, Output Ceramic
100µF, 6.3V, 1210
GRM32ER60J107M
TDK, Output Ceramic
100µF, 6.3V, 1210
C3225X5R0J107M
AVX, Output Ceramic
100µF, 6.3V, 1210
12106D107MAT2A
SANYO POSCAP, Output Bulk
470µF, 4V
4TPE470MCL
SANYO POSCAP, Output Bulk
470µF, 6.3V
6TPF470MAH
FN8670 Rev.5.00
Nov 8, 2017
Page 9 of 59
ISL8272M
Absolute Maximum Ratings
Thermal Information
Input Supply Voltage, VIN Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 17V
Input Supply Voltage for Controller, VDD Pin . . . . . . . . . . . . . . -0.3V to 17V
MOSFET Switch Node Voltage, SW1/2, SWD1/2 . . . . . . . . . . . -0.3V to 17V
MOSFET Driver Supply Voltage, VDRV, VDRV1 Pin . . . . . . . . . -0.3V to 6.0V
Output Voltage, VOUT pin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-0.3V to 6.0V
Internal Reference Supply Voltage, VR6 Pin . . . . . . . . . . . . . . -0.3V to 6.6V
Internal Reference Supply Voltage, VR, VR5, VR55 Pin. . . . . -0.3V to 6.5V
Internal Reference Supply Voltage, V25 Pin . . . . . . . . . . . . . . . . -0.3V to 3V
Logic I/O Voltage for DDC, EN, MGN, PG, ASCR, CS
SA, SCL, SDA, SALRT, SYNC, SS/UVLO, VMON, VSET . . . . . -0.3V to 6.0V
Analog Input Voltages for
VSENP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 6.0V
VSENN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 0.3V
ESD Rating
Human Body Model (Tested per JESD22-A114F) . . . . . . . . . . . . . . 2000V
Machine Model (Tested per JESD22-A115C) . . . . . . . . . . . . . . . . . . 200V
Charged Device Model (Tested per JESD22-C110D) . . . . . . . . . . . . 750V
Latch-Up (Tested per JESD78C; Class 2, Level A) . . . . . . . . . . . . . . . 100mA
Thermal Resistance (Typical)
JA (°C/W) JC (°C/W)
58 LD HDA Package (Notes 12, 13). . . . . .
6.55
1.6
Maximum Junction Temperature (Plastic Package) . . . . . . . . . . . .+125°C
Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-55°C to +150°C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . Refer to Figure 30
Recommended Operating Conditions
Input Supply Voltage Range, VIN . . . . . . . . . . . . . . . . . . . . . . . . 4.5V to 14V
Input Supply Voltage Range for Controller, VDD . . . . . . . . . . . 4.5V to 14V
Output Voltage Range, VOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.6V to 5V
Output Current Range, IOUT(DC) (Note 16). . . . . . . . . . . . . . . . . . . 0A to 50A
Operating Junction Temperature Range, TJ. . . . . . . . . . . .-40°C to +125°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
12. JA is measured in free air with the module mounted on an 6-layer evaluation board 4.7x4.8inch in size with 2oz surface and 2oz buried planes and
multiple via interconnects as specified in the ISL8272MEVAL1Z Evaluation Board User Guide.
13. For JC, the “case temp” location is the center of the package underside.
Electrical Specifications
VIN = VDD= 12V, fSW = 533kHz, TA = -40°C to +85°C, unless otherwise noted. Typical values are at
TA = +25°C. Boldface limits apply across the operating temperature range, -40°C to +85°C.
SYMBOL
PARAMETER
TEST CONDITIONS
TYP
MAX
(Note 14)
UNITS
40
50
mA
5.5
6.1
6.6
V
4.5
5.2
5.5
V
2.25
2.5
2.75
V
MIN
(Note 14)
INPUT AND SUPPLY CHARACTERISTICS
IDD
Input Supply Current for Controller
VR6
6V Internal Reference Supply Voltage
VR5
5V Internal Reference Supply
V25
2.5V Internal Reference Supply
Vcc
Internal LDO Output Voltage
IVCC
Internal LDO Output Current
VDD_READ_RES
Input Supply Voltage for Controller
Read Back Resolution
VDD_READ_ERR
Input Supply Voltage for Controller
Read Back Total Error (Note 17)
VIN = VDD = 12V, VOUT = 0V, module
not enabled
IVR5 <5mA
5.3
VIN = VDD = 12V, VCC connected to
VDRV, module enabled
V
50
PMBus Read
mA
10
Bits
±2
%FS
OUTPUT CHARACTERISTICS
VOUT_RANGE
Output Voltage Adjustment Range
VIN > VOUT + 1.8V
VOUT_RES
Output Voltage Set-Point Range
Configured using PMBus
VOUT_ACCY
Output Voltage Set-Point Accuracy
(Notes 15, 17)
Includes line, load and temperature
(-20°C ≤ TA ≤ +85°C)
VOUT_READ_RES
Output Voltage Read Back Resolution
VOUT_READ_ERR
Output Voltage Read Back Total Error
(Note 17)
IOUT_READ_RES
Output Current Read Back Resolution
FN8670 Rev.5.00
Nov 8, 2017
0.54
5.5
±0.025
-1
+1
10
PMBus read
-2
%VOUT
Bits
+2
10
V
%
%VOUT
Bits
Page 10 of 59
ISL8272M
Electrical Specifications
VIN = VDD= 12V, fSW = 533kHz, TA = -40°C to +85°C, unless otherwise noted. Typical values are at
TA = +25°C. Boldface limits apply across the operating temperature range, -40°C to +85°C. (Continued)
SYMBOL
IOUT_RANGE
IOUT_READ_ERR
PARAMETER
TEST CONDITIONS
MIN
(Note 14)
TYP
Output Current Range (Note 16)
Output Current Read back Total Error
PMBus read at max load. VOUT = 1V
MAX
(Note 14)
UNITS
50
A
±3
A
SOFT-START AND SEQUENCING
tON_DELAY
tON_DELAY_ACCY
Delay Time From Enable to VOUT Rise
Configured using PMBus
tON_DELAY Accuracy
Output Voltage Ramp-Up Time
Configured using PMBus. Single
module standalone
tON_RISE_ACCY
Output Voltage Ramp-Up Time
Accuracy
Single module standalone
Delay Time From disable to VOUT Fall
Configured using PMBus
tOFF_DELAY_ACCY
tOFF_FALL
tON_FALL_ACCY
5000
±2
tON_RISE
tOFF_DELAY
2
0.5
ms
100
±250
2
tOFF_DELAY Accuracy
Configured using PMBus. Single
module standalone
5000
Output Voltage Fall Time Accuracy
Single module standalone
Power-Good Delay
Configured using PMBus
0.5
ms
µs
±2
Output Voltage Fall Time
ms
ms
ms
100
±250
ms
µs
POWER-GOOD
VPG_DELAY
0
5000
ms
-50
150
C
-5
+5
C
4.18
16
V
TEMPERATURE SENSE
TSENSE_RANGE
Temperature Sense Range
INT_TEMPACCY
Internal Temperature Sensor Accuracy Tested at +100°C
Configurable using PMBus
FAULT PROTECTION
VDD_UVLO_RANGE
VDD Undervoltage Threshold Range
Measured internally
VDD_UVLO_ACCY
VDD Undervoltage Threshold Accuracy
(Note 17)
±2
%FS
VDD_UVLO_DELAY
VDD Undervoltage Response Time
10
µs
VOUT_OV_RANGE
VOUT Overvoltage Threshold Range
1.15VOUT
V
Factory default
Configured using PMBus
VOUT_UV_RANGE
VOUT Undervoltage Threshold Range
Factory default
Configured using PMBus
VOUT_OV/UV_ACCY
VOUT OV/UV Threshold Accuracy
(Note 15)
VOUT_OV/UV_DELAY
VOUT OV/UV Response Time
1.05VOUT
VOUT_MAX
0.85VOUT
V
V
0
0.95VOUT
V
-2
+2
%
10
µs
±10
% FS
ILIMIT_ACCY
Output Current Limit Set-Point
Accuracy (Note 17)
Tested at IOUT_OC_FAULT_LIMIT = 50A
ILIMIT_DELAY
Output Current Fault Response Time
(Note 18)
Factory default
3
tSW
Over-temperature Protection
Threshold
(Controller Junction Temperature)
Factory default
125
C
TJUNCTION
TJUNCTION_HYS
FN8670 Rev.5.00
Nov 8, 2017
Thermal Protection Hysteresis
Configured using PMBus
-40
125
15
C
C
Page 11 of 59
ISL8272M
Electrical Specifications
VIN = VDD= 12V, fSW = 533kHz, TA = -40°C to +85°C, unless otherwise noted. Typical values are at
TA = +25°C. Boldface limits apply across the operating temperature range, -40°C to +85°C. (Continued)
SYMBOL
PARAMETER
TEST CONDITIONS
MAX
(Note 14)
UNITS
296
1067
kHz
-5
+5
%
MIN
(Note 14)
TYP
OSCILLATOR AND SWITCHING CHARACTERISTICS
fSW_RANGE
fSW_ACCY
EXT_SYNCPW
EXT_SYNCDRIFT
Switching Frequency Range
Switching Frequency Set-Point
Accuracy
Minimum Pulse Width Required from
External SYNC Clock
Measured at 50% amplitude
Drift Tolerance for External SYNC Clock External SYNC Clock equal to 500kHz
is not supported
150
ns
-10
+10
%
-100
+100
nA
0.8
V
LOGIC INPUT/OUTPUT CHARACTERISTICS
ILOGIC_BIAS
Bias Current at the Logic Input Pins
VLOGIC_IN_LOW
Logic Input Low Threshold Voltage
VLOGIC_IN_HIGH
Logic Input High Threshold Voltage
VLOGIC_OUT_LOW
Logic Output Low Threshold Voltage
2mA sinking
VLOGIC_OUT_HIGH
Logic Output High Threshold Voltage
2mA sourcing
DDC, EN, MGN, PG, SA, SCL, SDA,
SALRT, SYNC, UVLO, VMON, VSET
2.0
V
0.5
2.25
V
V
PMBus INTERFACE TIMING CHARACTERISTIC
fSMB
PMBus Operating Frequency
100
400
kHz
NOTES:
14. Compliance to datasheet limits is assured by one or more methods: Production test, characterization and/or design. Controller is independently
tested before module assembly.
15. VOUT measured at the termination of the VSENP and VSENN sense points.
16. The MAX load current is determined by the thermal “Derating Curves” on page 15 provided with this document.
17. “FS” stands for full scale of recommended maximum operation range.
18. “tSW” stands for time period of operation switching frequency.
FN8670 Rev.5.00
Nov 8, 2017
Page 12 of 59
ISL8272M
Typical Performance Curves
Efficiency Performance
Operating condition: TA = +25°C, no air flow. COUT = 1340µF. Typical values are used unless otherwise noted.
1.00
0.97
0.95
0.95
1.8V
0.85
1V
0.80
1.8V
1.2V
EFFICIENCY (%)
EFFICIENCY (%)
0.90
3.3V
2.5V
0.8V
0.75
0.93
0.91
0.89
1V
0.8V
0
5
10
15
20
25
30
IOUT (A)
35
40
45
Switching Frequency (kHz)
0.98
0.95
0.96
0.90
0.94
2.5V
1.8V
Efficiency (%)
Efficiency (%)
FIGURE 7. EFFICIENCY VS SWITCHING FREQUENCY AT VIN = 5V,
IOUT = 50A FOR VARIOUS OUTPUT VOLTAGES
1.00
0.85
5V
3.3V
1.2V
0.80
1V
1.8V
0.8V
0.70
3.3V
5V
0.92
0.90
0
5
0.86
10
15
20
25
30
35
40
45
0.8V
1V
1.2V
0.84
300 350 400 450 500 550 600 650 700 750 800 850 900
50
SWITCHING FREQUENCY (kHz)
IOUT (A)
FIGURE 9. EFFICIENCY vs SWITCHING FREQUENCY AT VIN = 9V,
IOUT = 50A FOR VARIOUS OUTPUT VOLTAGES
FIGURE 8. EFFICIENCY vs OUTPUT CURRENT AT VIN = 9V,
fSW = 300kHz FOR VARIOUS OUTPUT VOLTAGES
1.00
0.98
0.95
0.96
1.8V
2.5V
3.3V
5V
0.94
0.90
0.85
1.8V
2.5V
5V
3.3V
1.2V
0.80
1V
0.75
EFFICIENCY (%)
EFFICIENCY (%)
2.5V
0.88
0.75
0.92
0.90
0.88
0.86
0.70
0.84
0.8V
0.65
1.2V
0.85
300 350 400 450 500 550 600 650 700 750 800 850 900
50
FIGURE 6. EFFICIENCY vs OUTPUT CURRENT AT VIN = 5V,
fSW = 300kHz FOR VARIOUS OUTPUT VOLTAGES
0.65
3.3V
0.87
0.70
0.65
2.5V
0
5
10
15
20
25
30
IOUT (A)
35
40
45
FIGURE 10. EFFICIENCY vs OUTPUT CURRENT AT VIN = 12V,
fSW = 300kHz FOR VARIOUS OUTPUT VOLTAGES
FN8670 Rev.5.00
Nov 8, 2017
50
0.8V
1V
1.2V
0.82
300 350 400 450 500 550 600 650 700 750 800 850 900
SWITCHING FREQUENCY (kHz)
FIGURE 11. EFFICIENCY vs SWITCHING FREQUENCY AT VIN = 12V,
IOUT = 50A FOR VARIOUS OUTPUT VOLTAGES
Page 13 of 59
ISL8272M
Typical Performance Curves
(Continued)
Transient Response Performance Operating condition: VIN = 12V, fSW = 533kHz, IOUT = 0A/25A, IOUT slew rate > 100A/µs,
TA = +25°C, no air flow. Typical values are used unless otherwise noted.
FIGURE 12. 1V TRANSIENT RESPONSE. COUT = 8x100µF
CERAMIC + 4x470µF POSCAP
FIGURE 13. 1.8V TRANSIENT RESPONSE. COUT = 6x100µF
CERAMIC + 2x470µF POSCAP
FIGURE 14. 2.5V TRANSIENT RESPONSE. COUT = 4x100µF
CERAMIC + 2x470µF POSCAP
FIGURE 15. 3.3V TRANSIENT RESPONSE. COUT = 4x100µF
CERAMIC + 2x470µF POSCAP
FIGURE 16. 5V TRANSIENT RESPONSE. COUT = 4x100µF CERAMIC + 2x470µF POSCAP
FN8670 Rev.5.00
Nov 8, 2017
Page 14 of 59
ISL8272M
Typical Performance Curves
Derating Curves
(Continued)
All of the following curves were plotted at TJ = +115°C.
60
60
50
200LFM
40
400LFM
0LFM
30
20
LOAD CURRENT (A)
LOAD CURRENT (A)
50
10
0
40
50
60
70
80
90
TEMPERATURE (°C)
100
110
30
20
0
40
120
200LFM
50
60
110
120
50
LOAD CURRENT (A)
400LFM
200LFM
40
0LFM
30
20
200LFM
40
400LFM
0LFM
30
20
10
10
50
60
70
80
90
100
110
0
40
120
50
60
TEMPERATURE (°C)
80
90
100
110
120
FIGURE 20. 12VIN TO 1.8VOUT, fSW = 300kHz
60
50
50
200LFM
LOAD CURRENT (A)
60
40
70
TEMPERATURE (°C)
FIGURE 19. 5VIN TO 1.8VOUT, fSW = 300kHz
LOAD CURRENT (A)
100
60
50
400LFM
0LFM
30
20
400LFM
40
0LFM
30
200LFM
20
10
10
0
40
70
80
90
TEMPERATURE (°C)
FIGURE 18. 12VIN TO 1VOUT, fSW = 300kHz
60
LOAD CURRENT (A)
0LFM
10
FIGURE 17. 5VIN TO 1VOUT, fSW = 300kHz
0
40
400LFM
40
50
60
70
80
90
TEMPERATURE (°C)
FIGURE 21. 5VIN TO 2.5VOUT, fSW = 300kHz
FN8670 Rev.5.00
Nov 8, 2017
100
110
120
0
40
50
60
70
80
90
100
110
TEMPERATURE (°C)
FIGURE 22. 12VIN TO 2.5VOUT, fSW = 300kHz
Page 15 of 59
120
ISL8272M
Typical Performance Curves
(Continued)
Derating Curves
All of the following curves were plotted at TJ = +115°C.
The READ_INTERNAL_TEMP command value in the PowerNavigatorTM software is the temperature reading value of the internal controller.
The junction temperature of the power stage in the module may be higher than the READ_INTERNAL_TEMP command value. The temperature difference
depends on the operating conditions; in some extreme cases, the junction temperature of the power stage can be 30°C higher than the
READ_INTERNAL_TEMP command value.
60
60
50
400LFM
200LFM
40
LOAD CURRENT (A)
LOAD CURRENT (A)
50
0LFM
30
20
10
0
40
400LFM
40
0LFM
30
200LFM
20
10
50
60
70
80
90
100
110
0
40
120
50
60
TEMPERATURE (°C)
70
80
90
100
110
120
TEMPERATURE (°C)
FIGURE 23. 5VIN TO 3.3VOUT, fSW = 300kHz
FIGURE 24. 12VIN TO 3.3VOUT, fSW = 533kHz
60
LOAD CURRENT (A)
50
400LFM
40
0LFM
30
200LFM
20
10
0
40
50
60
70
80
90
100
110
120
TEMPERATURE (°C)
FIGURE 25. 12VIN TO 5VOUT, fSW = 533kHz
FN8670 Rev.5.00
Nov 8, 2017
Page 16 of 59
ISL8272M
Functional Description
TABLE 3. OUTPUT VOLTAGE RESISTOR SETTINGS (Continued)
SMBus Communications
The ISL8272M provides a PMBus digital interface that enables
the user to configure all aspects of the module operation as well
as monitor the input and output parameters. The ISL8272M can
be used with any SMBus host device. In addition, the module is
compatible with PMBus Power System Management Protocol
Specification Parts I and II version 1.2. The ISL8272M accepts
most standard PMBus commands. When configuring the device
with PMBus commands, it is recommended that the enable pin is
tied to SGND.
The SMBus device address is the only parameter that must be
set by external pins. All other device parameters can be set with
PMBus commands.
The ISL8272M can operate without the PMBus in pin-strap mode
with configurations programmed by pin-strap resistors, such as
output voltage, switching frequency, device SMBus address, input
UVLO, soft-start/stop, and current sharing. Note: pin-strap
resistors with 1% tolerance or better should be used for all the
pin-strap settings.
Output Voltage Selection
The output voltage may be set to a voltage between 0.6V and 5V
if the input voltage is higher than the desired output voltage by
an amount sufficient to maintain regulation.
The VSET pin is used to set the output voltage to levels as shown
in Table 3. The RSET resistor is placed between the VSET pin and
SGND. A standard 1% resistor is required.
TABLE 3. OUTPUT VOLTAGE RESISTOR SETTINGS
VOUT (V)
RSET (kΩ)
0.60
10
0.65
11
0.70
12.1
0.75
13.3
0.80
14.7
0.85
16.2
0.90
17.8
0.95
19.6
1.00
21.5, or connect to SGND
1.05
23.7
1.10
26.1
1.15
28.7
1.20
31.6, or OPEN
1.25
34.8
1.30
38.3
1.40
42.2
1.50
46.4
1.60
51.1
FN8670 Rev.5.00
Nov 8, 2017
VOUT (V)
RSET (kΩ)
1.70
56.2
1.80
61.9
1.90
68.1
2.00
75
2.10
82.5
2.20
90.9
2.30
100
2.50
110, or connect to V25
2.80
121
3.00
133
3.30
147
4.00
162
5.00
178
The output voltage may also be set to any value between 0.6V and
5V using the PMBus command VOUT_COMMAND. This device
supports dynamic voltage scaling by allowing change to the output
voltage set point during regulation. The voltage transition rate is
specified with the PMBus command VOUT_TRANSITION_RATE.
By default, VOUT_MAX is set 110% higher than VOUT set by the pin
strap resistor, which can be changed to any value up to 5.5V with
the PMBus command VOUT_MAX.
Soft-Start/Stop Delay and Ramp Times
The ISL8272M follows an internal start-up procedure after power
is applied to the VDD pin. The module requires approximately
60ms to 70ms to check for specific values stored in its internal
memory and programmed by pin-strap resistors. Once this
process is completed, the device is ready to accept commands
from the PMBus interface and the module is ready to be enabled.
If the module is to be synchronized to an external clock source,
the clock frequency must be stable prior to asserting the EN pin.
It may be necessary to set a delay from when an enable signal is
received until the output voltage starts to ramp to its target
value. In addition, the designer may wish to precisely set the time
required for VOUT to ramp to its target value after the delay
period has expired. These features may be used as part of an
overall in-rush current management strategy or to precisely
control how fast a load IC is turned on. The ISL8272M gives the
system designer several options for precisely and independently
controlling both the delay and ramp time periods. The soft-start
delay period begins when the EN pin is asserted and ends when
the delay time expires.
The soft-start delay and ramp up time can be programmed to
custom values with the PMBus commands TON_DELAY and
TON_RISE. When the delay time is set to 0ms, the device begins
its ramp-up after the internal circuitry has initialized
(approximately 2ms). When the soft-start ramp period is set to
0ms, the output ramps up as quickly as the output load
capacitance and loop settings allow. It is generally
Page 17 of 59
ISL8272M
recommended to set the soft-start ramp to a value greater than
1ms to prevent inadvertent fault conditions due to excessive
in-rush current.
Similar to the soft-start delay and ramp up time, the delay and
ramp down time for soft-stop/off can be programmed with the
PMBus commands TOFF_DELAY and TOFF_FALL. In addition, the
module can be configured as “immediate off” with the command
ON_OFF_CONFIG, such that the FETs are turned off immediately
after the delay time expires.
In Current Sharing mode where multiple ISL8272M modules are
connected in parallel, ASCR must be disabled for the ramp up
with the USER_CONFIG command. Therefore, the soft-start rise
time is not equal to TON_RISE. It can be calculated
approximately by Equation 1.
TON_RISE
Rise Time (ms)  -------------------------------  330kHz  12V
V IN  f SW
(EQ. 1)
In Current Sharing mode, ASCR will be enabled automatically
upon power good assertion after the ramp completes. To avoid
premature ASCR turn on, it is recommended to increase
POWER_GOOD_DELAY if the rise time exceeds 10ms. In addition,
only “immediate off” is supported for current sharing.
The SS/UVLO pin can be used to program the soft start/stop
delay time and ramp time to some typical values as shown in
Table 4. A standard 1% resistor is required.
TABLE 4. SOFT START/STOP RESISTOR SETTINGS
DELAY TIME (ms)
RAMP TIME (ms)
RSET (kΩ)
5
2
19.6, or connect to
SGND
10
2
21.5
5
5
23.7, or OPEN
10
5
26.1
Power-Good
The ISL8272M provides a Power-Good (PG) signal that indicates
the output voltage is within a specified tolerance of its target
level and no fault condition exists. By default, the PG pin asserts
if the output is within 10% of the target voltage. This limit may be
changed using the PMBus command POWER_GOOD_ON.
A PG delay period is defined as the time from when all conditions
within the ISL8272M for asserting PG are met to when the PG pin
is actually asserted. This feature is commonly used instead of
using an external reset controller to control external digital logic.
A PG delay can be programmed with the PMBus command
POWER_GOOD_DELAY.
Switching Frequency and PLL
The device’s switching frequency is set from 296kHz to 1067kHz
using the pin strap method (for standalone non-current sharing
module only) as shown in Table 5, or by using the PMBus
command FREQUENCY_SWITCH. The ISL8272M incorporates an
internal phase-locked loop (PLL) to clock the internal circuitry.
The PLL can be driven by an external clock source connected to
the SYNC pin. The incoming clock signal must be in the range of
300kHz to 1.33MHz and must be stable when the enable pin is
asserted. When using an external clock, the frequencies are not
limited to discrete values as when using the internal clock. The
external clock signal must not vary more than 10% from its initial
value and should have a minimum pulse width of 150ns. It is
recommended that when using an external clock, the same
frequency should be set in the FREQUENCY_SWITCH command.
In case the external clock is lost, the module will automatically
switch to the internal clock. When using the internal oscillator,
the SYNC pin can be configured as a clock source as an external
sync to other modules. Refer to the SYNC_CONFIG command on
page 48 for more information. Note: if the pin-strap method is
used, a standard 1% resistor is required.
20
5
28.7
5
10
31.6
fSW (kHz)
RSET (kΩ)
10
10
34.8, or connect to V25
296
14.7, or connect to SGND
20
10
38.3
320
16.2
5
2
42.2
364
17.8
19.6
TABLE 5. SWITCHING FREQUENCY RESISTOR SETTINGS
10
2
46.4
400
5
5
51.1
421
21.5, or OPEN
471
23.7
10
5
56.2
20
5
61.9
5
10
68.1
10
10
75
20
10
82.5
FN8670 Rev.5.00
Nov 8, 2017
533
26.1
571
28.7
615
31.6, or connect to V25
727
34.8
800
38.3
842
42.2
889
46.4
1067
51.1
Page 18 of 59
ISL8272M
Loop Compensation
The module loop response is programmable using the PMBus
command ASCR_CONFIG or by using the pin-strap method (ASCR
pin) according to Table 6. A standard 1% resistor is required. The
ISL8272M uses the ChargeMode™ control algorithm that
responds to output current changes within a single PWM
switching cycle, achieving a smaller total output voltage variation
with less output capacitance than traditional PWM controllers.
TABLE 6. ASCR RESISTOR SETTINGS
Fault response to an input undervoltage fault can be programmed
with PMBus command VIN_UV_FAULT_RESPONSE. If the input
undervoltage fault retry is enabled, the module will shut down
immediately once the input voltage falls below VUVLO and then
check the input voltage every 70ms. If the input voltage rises
above the input undervoltage warning level, the module will
restart. The input undervoltage warning is 1.05*VUVLO by default
and can be programmed with the PMBus command
VIN_UV_WARN_LIMIT. Note that fault retry is not supported in the
current sharing configuration.
ASCR GAIN
ASCR RESIDUAL
RSET
(kΩ)
80
90
10
UVLO
(V)
120
90
11, or connect to SGND
4.5
OPEN
160
90
12.1
4.5
Connect to V25
200
90
13.3, or OPEN
4.5
Connect to SGND
240
90
14.7
4.5
280
90
16.2
19.6, 21.5, 23.7, 26.1, 28.7, 31.6,
34.8, 38.3
320
90
17.8
10.8
360
90
19.6
42.2, 46.4, 51.1, 56.2, 61.9, 68.1,
75, 82.5,
400
90
21.5
SMBus Module Address Selection
450
90
23.7
500
90
26.1
550
90
28.7
600
90
31.6
700
90
34.8
Each module must have its own unique serial address to
distinguish between other devices on the bus. The module
address is set by connecting a resistor between the SA pin and
SGND. Table 8 lists the available module addresses. A standard
1% resistor is required.
800
90
38.3
80
100
42.2
120
100
46.4
160
100
51.1
200
100
56.2
240
100
61.9
280
100
68.1
320
100
75
360
100
400
TABLE 7. UVLO RESISTOR SETTINGS
RSET
(kΩ)
TABLE 8. SMBus ADDRESS RESISTOR SELECTION
RSA (kΩ)
SMBus ADDRESS
10
19h
11
1Ah
12.1
1Bh
13.3
1Ch
14.7
1Dh
16.2
1Eh
82.5
17.8
1Fh
100
90.9
19.6
20h
450
100
100
21.5
21h
500
100
110, or connect to V25
23.7
22h
550
100
121
26.1
23h
600
100
133
28.7
24h
700
100
147
31.6
25h
800
100
162
34.8, or connect to SGND
26h
38.3
27h
Input Undervoltage Lockout (UVLO)
The input undervoltage lockout (UVLO) prevents the ISL8272M
from operating when the input falls below a preset threshold,
indicating the input supply is out of its specified range. The UVLO
threshold (VUVLO) can be set between 4.18V and 16V by using a
PMBus command VIN_UV_FAULT_LIMIT. Using the pin strap
method (SS/UVLO pin) as shown in Table 7, allows to set the
VUVLO to two typical values. A standard 1% resistor is required.
FN8670 Rev.5.00
Nov 8, 2017
42.2, or Open
28h
46.4
29h
51.1
2Ah
56.2
2Bh
61.9
2Ch
68.1
2Dh
75
2Eh
Page 19 of 59
ISL8272M
TABLE 8. SMBus ADDRESS RESISTOR SELECTION (Continued)
RSA (kΩ)
SMBus ADDRESS
82.5
2Fh
90.9
30h
100
31h
110
32h
121
33h
133
34h
147
35h
162
36h
178
37h
Output Overvoltage Protection
The ISL8272M offers an internal output overvoltage protection
circuit that can protect sensitive load circuitry from being
subjected to a voltage higher than its prescribed limits. A
hardware comparator compares the actual output voltage (seen
at the VSENP and VSENN pins) to a threshold set to 15% higher
than the target output voltage (the default setting). The fault
threshold can be programmed to a desired level with the PMBus
command VOUT_OV_FAULT_LIMIT. If the VSENP voltage exceeds
this threshold, the module will initiate an immediate shutdown
without retry. A 70ms continuous retry can be enabled with the
PMBus command VOUT_OV_FAULT_RESPONSE. Note that fault
retry is not supported in the current sharing configuration.
Internal to the module, two 22Ω resistors are populated from
VOUT to VSENP and SGND to VSENN to protect from overvoltage
conditions in case of open at voltage sensing pins and
differential remote sense traces due to assembly error. As long
as differential remote sense traces have low resistance, VOUT
regulation accuracy is not sacrificed.
Output Prebias Protection
An output prebias condition exists when an externally applied
voltage is present on a power supply’s output before the power
supply’s control IC is enabled. Certain applications require that
the converter not be allowed to sink current during start-up if a
prebias condition exists at the output. The ISL8272M provides
prebias protection by sampling the output voltage prior to
initiating an output ramp.
If a prebias voltage lower than the target voltage exists after the
pre-configured delay period has expired, the target voltage is set
to match the existing prebias voltage and both drivers are
enabled. The output voltage is then ramped to the final
regulation value at the pre-configured ramp rate.
The actual time the output takes to ramp from the prebias
voltage to the target voltage varies, depending on the prebias
voltage; however, the total time elapsed from when the delay
period expires to when the output reaches its target value will
match the pre-configured ramp time (see Figure 26).
FN8670 Rev.5.00
Nov 8, 2017
VOUT
DESIRED OUTPUT
VOLTAGE
PREBIAS
VOLTAGE
TIME
TONDELAY
TONRISE
VPREBIAS < VTARGET
VOUT
PREBIAS
VOLTAGE
DESIRED OUTPUT
VOLTAGE
TIME
TONDELAY
TONRISE
VPREBIAS > VTARGET
FIGURE 26. OUTPUT RESPONSES TO PREBIAS VOLTAGES
If a prebias voltage is higher than the target voltage after the preconfigured delay period has expired, the target voltage is set to
match the existing prebias voltage and both drivers are enabled
with a PWM duty cycle that would ideally create the prebias
voltage.
Once the preconfigured soft-start ramp period has expired, the
PG pin is asserted (assuming the prebias voltage is not higher
than the overvoltage limit). The PWM then adjusts its duty cycle
to match the original target voltage and the output ramps down
to the pre-configured output voltage.
If a prebias voltage is higher than the overvoltage limit, the
device does not initiate a turn-on sequence and declares an
overvoltage fault condition. The device then responds based on
the output overvoltage fault response setting programmed with
the PMBus command VOUT_OV_FAULT_RESPONSE.
Output Overcurrent Protection
The ISL8272M can protect the power supply from damage if the
output is shorted to ground or if an overload condition is imposed
on the output. Average output overcurrent fault threshold can be
programmed with the PMBus command IOUT_OC_FAULT_LIMIT.
The module automatically programs the peak inductor current
fault threshold by calculating the inductor ripple current from the
input voltage, switching frequency, and the VOUT_COMMAND.
When the peak inductor current crosses the peak inductor
current fault threshold for three successive switching cycles it will
initiate an immediate shutdown.
The default response from an overcurrent fault is an immediate
shutdown without retry. A 70ms continuous retry can be enabled
with the PMBus command MFR_IOUT_OC_FAULT_RESPONSE. It
is required to enable the output undervoltage fault retry with the
PMBus command VOUT_UV_FAULT_RESPONSE command
simultaneously if the overcurrent fault retry is enabled. Note that
fault retry is not supported in the current sharing configuration.
Page 20 of 59
ISL8272M
Thermal Overload Protection
The ISL8272M includes a thermal sensor that continuously
measures the internal temperature of the module and shuts
down the controller when the temperature exceeds the preset
limit. The default temperature limit is set to +125°C in the
factory, but can be changed with PMBus command
OT_FAULT_LIMIT.
The default response from an over-temperature fault is an
immediate shutdown without retry. Retry settings can be
programmed with the PMBus command OT_FAULT_RESPONSE.
Hysteresis is implemented with the over-temperature fault retry.
If retry is enabled, the module will shut down immediately upon
an over-temperature fault event and then check the temperature
every 70ms. If the temperature falls below the over-temperature
warning level, the module will restart. The over-temperature
warning is +105°by default and programmable with the PMBus
command OT_WARN_LIMIT. Note that fault retry is not supported
in the current sharing configuration.
Digital-DC Bus
The Digital-DC Communications (DDC) bus is used to
communicate between Intersil digital power modules and digital
controllers. This dedicated bus provides the communication
channel between devices for features such as current sharing,
sequencing, and fault spreading. The DDC pin on all Digital-DC
devices in an application should be connected together. A pull-up
resistor is required on the DDC bus in order to guarantee the rise
time as shown in Equation 2:
(EQ. 2)
Rise Time = R PU C LOAD  1s
where RPU is the DDC bus pull-up resistance and CLOAD is the
bus loading. The pull-up resistor may be tied to an external 3.3V
or 5V supply as long as this voltage is present prior to or during
device power-up. In principle, each device connected to the DDC
bus presents approximately 10pF of capacitive loading and each
inch of FR4 PCB trace introduces approximately 2pF. The ideal
design uses a central pull-up resistor that is well-matched to the
total load capacitance.
Active Current Sharing
Paralleling multiple ISL8272M modules can increase the output
current capability of a single power rail. By connecting the DDC
and SYNC pins of each module together and configuring the
modules as a current sharing rail, the units will share the current
equally within a few percent.
VIN
3.3V TO 5V
CIN
DDC
ISL8272M
COUT
SYNC
CIN
DDC
ISL8272M
VOUT
COUT
SYNC
FIGURE 27. CURRENT SHARING GROUP
The ISL8272M uses a DDC bus based digital current sharing
technique to balance the steady state module output current by
aligning the load lines of member modules to a reference
module.
When multiple ISL8272M modules are connected for current
sharing, a non-zero active droop resistance must be set to add
artificial resistance in the output voltage path to control the slope
of the load line curve, calibrating out the physical parasitic
mismatches due to power train components and PCB layout. The
active droop resistance can be programmed with the PMBus
command VOUT_DROOP based on Equation 3. Typically, higher
droop value offers a more accurate dynamic current sharing at
the sacrifice of output load regulation. 1% droop at full load will
be a good trade-off between output load regulation and dynamic
current sharing.
(EQ. 3)
V OUT
V OUT
---------------------------------  0.005  Droop  ---------------------------------  0.01 5
I LOAD  MAX 
I LOAD  MAX 
Upon system start-up, the module with the lowest device position
as selected in DDC_CONFIG is defined as the reference module.
The remaining modules are members. The reference module
broadcasts its current over the DDC bus. The members use the
reference current information to trim their voltages (VMEMBER) to
balance the current loading of each module in the system.
VREFERENCE
Figure 27 illustrates a typical connection for two modules.
VOUT
-R
VMEMBER
-R
I MEMBER
I OUT
I REFERENCE
FIGURE 28. ACTIVE CURRENT SHARING
FN8670 Rev.5.00
Nov 8, 2017
Page 21 of 59
ISL8272M
Figure 28 on page 21 shows that, for load lines with identical
slopes, the member voltage is increased towards the reference
voltage which closes the gap between the inductor currents.
TABLE 9. CURRENT SHARING RESISTOR SETTINGS (Continued)
CLOCK
CONFIGURATION
DEVICE POSITION
- NUMBER OF
DEVICES
DROOP
(mV/A)
RSET
(kΩ)
Output internal
1-3
0.13
46.4
External
2-3
0.13
51.1
External
3-3
0.13
56.2
Output internal
1-3
0.16
61.9
External
2-3
0.16
68.1
External
3-3
0.16
75
For fault configuration, it is required to enable the fault spreading
mode in the current sharing rail with the PMBus command
DDC_GROUP. Broadcast operation must be enabled with the
DDC_GROUP command to allow start up/shut down and
margining operations. It is optional to enable VOUT broadcast in
the DDC_GROUP command to allow VOUT set point change
dynamically during operation.
Output internal
1-3
0.2
82.5
External
2-3
0.2
90.9
External
3-3
0.2
100
Output internal
1-4
0.14
110 (available
with FC02
firmware only)
In the multiple-module current sharing configuration, it is
required to synchronize all modules to the same switching clock
by tying the SYNC pins together. The clock source can be selected
either from one module or from an external clock with the
SYNC_CONFIG command. The phase offset of current sharing
modules is automatically set according to the device positions
and number of devices specified in the DDC_CONFIG command.
External
2-4
0.14
121 (available
with FC02
firmware only)
External
3-4
0.14
133 (available
with FC02
firmware only)
External
4-4
0.14
147 (available
with FC02
firmware only)
Internal only
1-1
0
Connect to SGND
(for immediate
off)
Internal only
1-1
0
OPEN
(for soft off)
The relation between reference and member current and voltage
is given by Equation 4:
V MEMBER = V OUT + R   I REFERENCE – I MEMBER 
(EQ. 4)
where R is the value of the droop resistance.
The DDC_CONFIG command configures the module for active
current sharing. The default setting is a standalone non current
sharing module.
The pin strap method is offered for the current sharing
configuration with the CS pin. Table 9 lists the current sharing pin
strap settings. A standard 1% resistor is required. Note that fault
retry is not supported in the current sharing configuration.
TABLE 9. CURRENT SHARING RESISTOR SETTINGS
DEVICE POSITION
- NUMBER OF
CLOCK
DEVICES
CONFIGURATION
DROOP
(mV/A)
RSET
(kΩ)
Output internal
1-2
0.1
10
External
2-2
0.1
11
Output internal
1-2
0.15
12.1
External
2-2
0.15
13.3
Output internal
1-2
0.2
14.7
External
2-2
0.2
16.2
Output internal
1-2
0.25
17.8
External
2-2
0.25
19.6
Output internal
1-2
0.3
21.5
External
2-2
0.3
23.7
Output internal
1-3
0.07
26.1
External
2-3
0.07
28.7
External
3-3
0.07
31.6
Output internal
1-3
0.1
34.8
External
2-3
0.1
38.3
External
3-3
0.1
42.2
FN8670 Rev.5.00
Nov 8, 2017
Phase Spreading
When multiple point-of-load converters share a common DC
input supply, it is desirable to adjust the clock phase offset of
each device so that not all devices start to switch simultaneously.
Setting each converter to start its switching cycle at a different
point in time can dramatically reduce input capacitance
requirements and efficiency losses. Because the peak current
drawn from the input supply is effectively spread out over a
period of time, the peak current drawn at any given moment is
reduced and the power losses proportional to the IRMS2 are
reduced dramatically.
To enable phase spreading, all converters must be synchronized
to the same switching clock. The phase offset of each device
may also be set to any value between 0° and 360° in 22.5°
increments with the PMBus command INTERLEAVE. The internal
two phases of the module always maintain a phase difference
of 180°.
Fault Spreading
Digital-DC modules and devices can be configured to broadcast a
fault event over the DDC bus to the other devices in the group
with the PMBus command DDC_GROUP. When a nondestructive
fault occurs, the device shuts down and broadcasts the fault
Page 22 of 59
ISL8272M
event over the DDC bus. The other devices on the DDC bus shut
down simultaneously if configured to do so, and attempt to
restart.
Note that fault retry is not supported in multiple modules with
fault spreading enabled, such as the current sharing
configuration.
Output Sequencing
A group of Digital-DC modules or devices may be configured to
power-up in a predetermined sequence. This feature is especially
useful when powering advanced processors (FPGAs and ASICs)
that require one supply to reach its operating voltage prior to
another supply reaching its operating voltage in order to avoid
latch-up. Multi-device sequencing can be achieved by configuring
each device with the PMBus command SEQUENCE. Multiple
device sequencing is configured by issuing PMBus commands to
assign the preceding device in the sequencing chain as well as
the device that follows in the sequencing.
The Enable pins of all devices in a sequencing group must be tied
together and driven high to initiate a sequenced turn-on of the
group. Enable must be driven low to initiate a sequenced turnoff
of the group. It is recommend to enable fault spreading with the
PMBus command DDC_GROUP within a sequencing group.
Monitoring with SMBus
A system controller can monitor a wide variety of different
ISL8272M system parameters with PMBus commands:
• READ_VIN
• READ_VOUT
• READ_IOUT
• READ_INTERNAL_TEMP
• READ_DUTY_CYCLE
• READ_FREQEUNCY
• READ_VMON
Snapshot Parameter Capture
The ISL8272M offers a special feature to capture parametric data
and some fault status following a fault. A detailed description is
provided in “PMBus Commands Description” on page 29 under
the PMBus commands SNAPSHOT and SNAPSHOT_CONTROL.
Layout Guide
To achieve stable operation, low losses, and good thermal
performance, proper layout (Figure 29) is important.
• Establish separate SGND plane and PGND planes, then
connect SGND to the PGND plane on the middle layer and
underneath PAD6 with a single point connection. For SGND
and PGND pin connections, such as small pins H16, J16, M5,
and M17..., use multiple vias for each pin to connect to the
inner SGND or PGND layer.
• Place enough ceramic capacitors between VIN and PGND,
VOUT and PGND and bypass capacitors between VDD, VDRV
and the ground plane, as close to the module as possible to
minimize high frequency noise. It is critical to place the output
ceramic capacitors as close to the center of the two VOUT pads
as possible, to create a low impedance path for the high
frequency inductor ripple current.
• Use large copper areas for power path (VIN, PGND, VOUT) to
minimize conduction loss and thermal stress. Also, use
multiple vias to connect the power planes in different layers. It
is recommended to enlarge PAD11 and PAD15 and to put
more vias on these pads. The ceramic caps CIN can be put on
the bottom layer under these two pads.
• Connect remote sensed traces to the regulation points to
achieve a tight output voltage regulation and keep them in
parallel. Route a trace from VSENN and VSENP to the point of
load where the tight output voltage is desired. Avoid routing
any sensitive signal traces, such as the VSENN, VSENP sensing
point near the SW pins.
• The SW1 and SW2 pads are noisy pads, but they are beneficial
for thermal dissipations. If the noise issue is critical for the
applications, it is recommended to use top layer only for SW
pads. For better thermal performance, use multiple vias on
these pads to connect into SW inner and bottom layer.
However, be very careful when placing limited SW planes in
any layer. The SW planes should avoid the sensing signals and
should be surrounded by the PGND layer to avoid noise
coupling.
• For pins SWD1 (L3) and SWD2 (P10), it is recommended to
connect to the related SW1 and SW2 pads with short loop
wires. The wire width should be greater than 20 mils.
Nonvolatile Memory
The ISL8272M has internal nonvolatile memory where user
configurations are stored. Integrated security measures ensure
that the user can only restore the module to a level that has been
made available to them. During the initialization process, the
ISL8272M checks for stored values contained in its internal
nonvolatile memory.
Modules are shipped with a factory default configuration and
most settings can be overwritten with PMBus commands and
can be stored in nonvolatile memory with the PMBus command
STORE_USER_ALL.
FN8670 Rev.5.00
Nov 8, 2017
Page 23 of 59
ISL8272M
COUT
VOUT
also feature an array of solder mask defined lands and should
match 1:1 with the package exposed die pad perimeters. The
exposed solder mask defined PCB land area should be 50-80%
of the available module I/O area.
COUT
PGND
PGND
Thermal Vias
PGND
VSEN- VSEN+
Kelvin Connections
VIN
VIN
CIN
CIN
PGND
FIGURE 29. RECOMMENDED LAYOUT
Thermal Considerations
Experimental power loss curves along with θJA from thermal
modeling analysis can be used to evaluate the thermal
consideration for the module. The derating curves are derived
from the maximum power allowed while maintaining the
temperature below the maximum junction temperature of
+125°C. In actual applications, other heat sources and design
margins should be considered.
Package Description
The structure of the ISL8272M belongs to the High Density Array
No-lead package (HDA). This package offers good thermal and
electrical conductivity, low weight, and small size. The HDA
package is applicable for surface mounting technology and is
being more readily used in the industry. The ISL8272M contains
several types of devices, including resistors, capacitors,
inductors, and control ICs. The ISL8272M is a copper lead-frame
based package with exposed copper thermal pads, which have
good electrical and thermal conductivity. The copper lead frame
and multi component assembly is overmolded with polymer
mold compound to protect these devices.
The package outline and typical PCB layout pattern design and
typical stencil pattern design are shown in the “Package Outline
Drawing” starting on page 53. The module has a small size of
18mmx23mmx7.5mm.
PCB Layout Pattern Design
The bottom of the ISL8272M is a lead-frame footprint, which is
attached to the PCB by a surface mounting process. The PCB
layout pattern is shown on pages 57 to 59. The PCB layout
pattern is an array of solder mask defined PCB lands which align
with the perimeters of the HDA exposed pads and I/O
termination dimensions. The thermal lands on the PCB layout
FN8670 Rev.5.00
Nov 8, 2017
Stencil Pattern Design
Reflowed solder joints on the perimeter I/O lands should have
about a 50µm to 75µm (2mil to 3mil) standoff height. The solder
paste stencil design is the first step in developing optimized,
reliable solder joints. The stencil aperture size to solder mask
defined PCB land size ratio should typically be 1:1. The aperture
width may be reduced slightly to help prevent solder bridging
between adjacent I/O lands. A typical solder stencil pattern is
shown in the “Package Outline Drawing” starting on page 55. The
gap width between pad to pad is 0.6mm. Consider the symmetry
of the whole stencil pattern when designing its pads. A laser cut,
stainless steel stencil with electropolished trapezoidal walls is
recommended. Electropolishing “smooths” the aperture walls,
resulting in reduced surface friction and better paste release which
reduces voids. Using a Trapezoidal Section Aperture (TSA) also
promotes paste release and forms a brick-like paste deposit that
assists in firm component placement. A 0.1mm to 0.15mm stencil
thickness is recommended for this large pitch HDA.
Reflow Parameters
Due to the HDA’s low mount height, “No Clean” Type 3 solder
paste per ANSI/J-STD-005 is recommended. Nitrogen purge is
recommended during reflow. A system board reflow profile
depends on the thermal mass of the entire populated board, so it
is not practical to define a specific soldering profile just for the
HDA. The profile in Figure 30 is a guideline to be customized for
varying manufacturing practices and applications.
300
PEAK TEMPERATURE ~+245°C;
TYPICALLY 60s-150s ABOVE +217°C
KEEP LESS THAN 30s WITHIN 5°C OF PEAK TEMP.
250
TEMPERATURE (°C)
SGND
PGND
A grid of 1.0mm to 1.2mm pitch thermal vias, which drops down
and connects to buried copper plane(s), should be placed under the
thermal land. The vias should be about 0.3mm to 0.33mm in
diameter with the barrel plated to about 1.0 ounce copper.
Although adding more vias (by decreasing via pitch) will improve
the thermal performance, diminishing returns will be seen as more
and more vias are added. Simply use as many vias as practical for
the thermal land size and your board design rules allow.
200
SLOW RAMP (3°C/s MAX)
AND SOAK FROM +150°C
TO +200°C FOR 60s~180s
150
100
RAMP RATE 1.5°C FROM +70°C TO +90°C
50
0
0
100
150
200
250
300
350
DURATION (s)
FIGURE 30. TYPICAL REFLOW PROFILE
Page 24 of 59
ISL8272M
PMBus Command Summary
COMMAND
CODE
COMMAND
NAME
DESCRIPTION
TYPE
DATA
FORMAT
DEFAULT
VALUE
DEFAULT
SETTING
PAGE
01h
OPERATION
Sets Enable, Disable and VOUT
Margin modes.
R/W BYTE
BIT
02h
ON_OFF_CONFIG
Configures the EN pin and PMBus
commands to turn the unit
ON/OFF
R/W BYTE
BIT
03h
CLEAR_FAULTS
Clears fault indications.
SEND BYTE
30
15h
STORE_USER_ALL
Stores all PMBus values written
since last restore at user level.
SEND BYTE
30
16h
RESTORE_USER_ALL
Restores PMBus settings that were
stored using STORE_USER_ALL.
SEND BYTE
30
20h
VOUT_MODE
Preset to defined data format of
VOUT commands.
READ BYTE
BIT
21h
VOUT_COMMAND
Sets the nominal value of the
output voltage.
R/W WORD
L16u
23h
VOUT_CAL_OFFSET
Applies a fixed offset voltage to the
VOUT_COMMAND.
R/W WORD
L16s
24h
VOUT_MAX
Sets the maximum possible value
of VOUT. 110% of pin strap VOUT.
R/W WORD
25h
VOUT_MARGIN_HIGH
Sets the value of the VOUT during a
margin high.
26h
VOUT_MARGIN_LOW
27h
29
16h
29
Linear Mode,
Exponent = -13
30
Pin Strap
30
0V
31
L16u
1.1*VOUT
Pin Strap
31
R/W WORD
L16u
1.05*VOUT
Pin Strap
31
Sets the value of the VOUT during a
margin low.
R/W WORD
L16u
0.95*VOUT
Pin Strap
31
VOUT_TRANSITION_RATE
Sets the transition rate during
margin or other change of VOUT.
R/W WORD
L11
1V/ms
31
28h
VOUT_DROOP
Sets the loadline (V/I Slope)
resistance for the rail.
R/W WORD
L11
Pin Strap
32
33h
FREQUENCY_SWITCH
Sets the switching frequency.
R/W WORD
L11
Pin Strap
32
37h
INTERLEAVE
Configures a phase offset between
devices sharing a SYNC clock.
R/W WORD
BIT
0000h
38h
IOUT_CAL_GAIN
Sense resistance for inductor DCR
current sensing.
R/W WORD
L11
B370h
0.86mΩ
32
39h
IOUT_CAL_OFFSET
Sets the current-sense offset.
R/W WORD
L11
0000h
0A
32
40h
VOUT_OV_FAULT_LIMIT
Sets the VOUT overvoltage fault
threshold.
R/W WORD
L16u
1.15*VOUT
Pin Strap
33
41h
VOUT_OV_FAULT_RESPONSE
Configures the VOUT overvoltage
fault response.
R/W BYTE
BIT
Disable and
No Retry
33
42h
VOUT_OV_WARN_LIMIT
Sets the VOUT overvoltage warn
threshold.
R/W WORD
L16u
1.10*VOUT
Pin Strap
33
43h
VOUT_UV_WARN_LIMIT
Sets the VOUT undervoltage warn
threshold.
R/W WORD
L16u
0.9 * VOUT
Pin Strap
33
44h
VOUT_UV_FAULT_LIMIT
Sets the VOUT undervoltage fault
threshold.
R/W WORD
L16u
0.85*VOUT
Pin Strap
33
45h
VOUT_UV_FAULT_RESPONSE
Configures the VOUT undervoltage
fault response.
R/W BYTE
BIT
80h
Disable and
No Retry
34
46h
IOUT_OC_FAULT_LIMIT
Sets the IOUT average overcurrent
fault threshold.
R/W WORD
L11
E3C0h
60A
34
4Bh
IOUT_UC_FAULT_LIMIT
Sets the IOUT average
undercurrent fault threshold.
R/W WORD
L11
E440h
-60A
34
4Fh
OT_FAULT_LIMIT
Sets the over-temperature fault
threshold.
R/W WORD
L11
EBE8h
+125°C
34
50h
OT_FAULT_RESPONSE
Configures the over-temperature
fault response.
R/W BYTE
BIT
80h
Disable and
No Retry
35
FN8670 Rev.5.00
Nov 8, 2017
13h
Hardware Enable,
Soft Off
0000h
BA00h
80h
32
Page 25 of 59
ISL8272M
PMBus Command Summary (Continued)
COMMAND
CODE
COMMAND
NAME
DESCRIPTION
TYPE
DATA
FORMAT
DEFAULT
VALUE
DEFAULT
SETTING
PAGE
51h
OT_WARN_LIMIT
Sets the over-temperature warning
limit.
R/W WORD
L11
EB48h
+105°C
35
52h
UT_WARN_LIMIT
Sets the under-temperature
warning limit.
R/W WORD
L11
DC40h
-30°C
35
53h
UT_FAULT_LIMIT
Sets the under-temperature fault
threshold.
R/W WORD
L11
E580h
-40°C
35
54h
UT_FAULT_RESPONSE
Configures the under-temperature
fault response.
R/W BYTE
BIT
80h
Disable and
No Retry
36
55h
VIN_OV_FAULT_LIMIT
Sets the VIN overvoltage fault
threshold.
R/W WORD
L11
D380h
14V
36
56h
VIN_OV_FAULT_RESPONSE
Configures the VIN overvoltage
fault response.
R/W BYTE
BIT
80h
Disable and
No Retry
36
57h
VIN_OV_WARN_LIMIT
Sets the input overvoltage warning
limit.
R/W WORD
L11
D353h
13.3V
36
58h
VIN_UV_WARN_LIMIT
Sets the input undervoltage
warning limit.
R/W WORD
L11
1.05*VIN
UV Fault Limit
37
59h
VIN_UV_FAULT_LIMIT
Sets the VIN undervoltage fault
threshold.
R/W WORD
L11
Pin Strap
37
5Ah
VIN_UV_FAULT_RESPONSE
Configures the VIN undervoltage
fault response.
R/W BYTE
BIT
Disable and
No Retry
37
5Eh
POWER_GOOD_ON
Sets the voltage threshold for
Power-Good indication.
R/W WORD
L16u
0.9*VOUT
Pin Strap
37
60h
TON_DELAY
Sets the delay time from ENABLE
to start of VOUT rise.
R/W WORD
L11
Pin Strap
37
61h
TON_RISE
Sets the rise time of VOUT after
ENABLE and TON_DELAY.
R/W WORD
L11
Pin Strap
38
64h
TOFF_DELAY
Sets the delay time from DISABLE
to start of VOUT fall.
R/W WORD
L11
Pin Strap
38
65h
TOFF_FALL
Sets the fall time for VOUT after
DISABLE and TOFF_DELAY.
R/W WORD
L11
Pin Strap
38
78h
STATUS_BYTE
Returns an abbreviated status for
fast reads.
READ BYTE
BIT
00h
No Faults
38
79h
STATUS_WORD
Returns information with a
summary of the units's fault
condition.
READ WORD
BIT
0000h
No Faults
39
80h
7Ah
STATUS_VOUT
Returns the VOUT specific status.
READ BYTE
BIT
00h
No Faults
39
7Bh
STATUS_IOUT
Returns the IOUT specific status.
READ BYTE
BIT
00h
No Faults
40
7Ch
STATUS_INPUT
Returns specific status specific to
the input.
READ BYTE
BIT
00h
No Faults
40
7Dh
STATUS_TEMPERATURE
Returns the temperature specific
status.
READ BYTE
BIT
00h
No Faults
40
7Eh
STATUS_CML
Returns the Communication, Logic
and Memory specific status.
READ BYTE
BIT
00h
No Faults
41
80h
STATUS_MFR_SPECIFIC
Returns the VMON and External
Sync clock specific status.
READ BYTE
BIT
00h
No Faults
41
88h
READ_VIN
Returns the input voltage reading.
READ WORD
L11
41
8Bh
READ_VOUT
Returns the output voltage
reading.
READ WORD
L16u
41
8Ch
READ_IOUT
Returns the output current
reading.
READ WORD
L11
42
8Dh
READ_INTERNAL_TEMP
Returns the temperature reading
internal to the device.
READ WORD
L11
42
FN8670 Rev.5.00
Nov 8, 2017
Page 26 of 59
ISL8272M
PMBus Command Summary (Continued)
COMMAND
CODE
COMMAND
NAME
DESCRIPTION
TYPE
DATA
FORMAT
DEFAULT
VALUE
DEFAULT
SETTING
PAGE
94h
READ_DUTY_CYCLE
Returns the duty cycle reading
during the ENABLE state.
READ WORD
L11
42
95h
READ_FREQUENCY
Returns the measured operating
switch frequency.
READ WORD
L11
42
96h
READ_IOUT_0
Returns phase 1 current reading.
READ WORD
L11
42
97h
READ_IOUT_1
Returns phase 2 current reading.
READ WORD
L11
99h
MFR_ID
Sets a user defined identification.
R/W BLOCK
ASC
Null
43
9Ah
MFR_MODEL
Sets a user defined model.
R/W BLOCK
ASC
Null
43
9Bh
MFR_REVISION
Sets a user defined revision.
R/W BLOCK
ASC
Null
43
9Ch
MFR_LOCATION
Sets a user defined location
identifier.
R/W BLOCK
ASC
Null
43
9Dh
MFR_DATE
Sets a user defined date.
R/W BLOCK
ASC
Null
43
9Eh
MFR_SERIAL
Sets a user defined serialized
identifier.
R/W BLOCK
ASC
Null
44
A8H
LEGACY_FAULT_GROUP
Sets rail IDs of legacy devices for
fault spreading
R/W BLOCK
BIT
B0h
USER_DATA_00
Sets a user defined data.
R/W BLOCK
ASC
D0h
ISENSE_CONFIG
Configures ISENSE related
features.
R/W BYTE
BIT
D1h
USER_CONFIG
Configures several user-level
features.
R/W BYTE
D3h
DDC_CONFIG
Configures the DDC bus.
D4h
POWER_GOOD_DELAY
DFh
42
00000000h No rail ID
specified
44
Null
44
256ns Blanking
Time, Mid Range
44
BIT
Pin Strap (ASCR
on/off for start
up)
45
R/W WORD
BIT
Pin Strap (set
based on PMBus
address and CS)
45
Sets the delay between VOUT > PG
threshold and asserting the PG
pin.
R/W WORD
L11
3ms
46
ASCR_CONFIG
Configures ASCR control loop.
R/W BLOCK
CUS
Pin Strap
46
E0h
SEQUENCE
Identifies the Rail DDC ID to
perform multi-rail sequencing.
R/W WORD
BIT
Prequel and
Sequel Disabled
46
E2h
DDC_GROUP
Sets rail DDC IDs to obey faults
and margining spreading
information.
R/W BLOCK
BIT
Pin Strap (set
based on CS)
47
E4h
DEVICE_ID
Returns the 16-byte (character)
device identifier string.
READ BLOCK
ASC
Reads Device
Version
47
E5h
MFR_IOUT_OC_FAULT_RESPONSE Configures the IOUT overcurrent
fault response.
R/W BYTE
BIT
80h
Disable and
No Retry
47
E6h
MFR_IOUT_UC_FAULT_RESPONSE Configures the IOUT undercurrent
fault response.
R/W BYTE
BIT
80h
Disable and
No Retry
48
E9h
SYNC_CONFIG
Configures the Sync pin.
R/W BYTE
BIT
Pin Strap (set
based on CS)
48
EAh
SNAPSHOT
Returns 32-byte read-back of
parametric and status values.
READ BLOCK
BIT
EBh
BLANK_PARAMS
Returns recently changed
parameter values.
READ BLOCK
BIT
F3h
SNAPSHOT_CONTROL
Snapshot feature control
command.
R/W BYTE
BIT
F4h
RESTORE_FACTORY
Restores device to the factory
default values.
SEND BYTE
F5h
MFR_VMON_OV_FAULT_LIMIT
Returns the VMON overvoltage
threshold.
READ WORD
FN8670 Rev.5.00
Nov 8, 2017
05h
C300h
0000h
49
FF...FFh
49
49
50
L11
CB00h
6V
Page 27 of 59
50
ISL8272M
PMBus Command Summary (Continued)
COMMAND
CODE
COMMAND
NAME
DESCRIPTION
TYPE
DATA
FORMAT
DEFAULT
VALUE
CA00h
DEFAULT
SETTING
PAGE
F6h
MFR_VMON_UV_FAULT_LIMIT
Returns the VMON undervoltage
threshold.
READ WORD
L11
4V
50
F7h
MFR_READ_VMON
Returns the VMON voltage
reading.
READ WORD
L11
F8h
VMON_OV_FAULT_RESPONSE
Returns the VMON overvoltage
response.
READ BYTE
BIT
80h
Disable and
No Retry
50
F9h
VMON_UV_FAULT_RESPONSE
Returns the VMON undervoltage
response.
READ BYTE
BIT
80h
Disable and No
Retry
50
50
PMBus Data Formats
Linear-11 (L11)
The L11 data format uses 5-bit two’s complement exponent (N) and 11-bit two’s complement mantissa (Y) to represent real world
decimal value (X).
Data Byte High
Data Byte Low
7 6 5 4 3 2 1 0
7 6 5 4 3 2 1 0
Exponent (N)
Mantissa (Y)
The relation between real world decimal value (X), N and Y is: X = Y·2N
Linear-16 Unsigned (L16u)
L16u data format uses a fixed exponent (hard-coded to N = -13h) and a 16-bit unsigned integer mantissa (Y) to represent real world
decimal value (X). Relation between real world decimal value (X), N and Y is: X = Y·2-13
Linear-16 Signed (L16s)
The L16s data format uses a fixed exponent (hard-coded to N = -13h) and a 16-bit two’s complement mantissa (Y) to represent real
world decimal value (X).
Relation between real world decimal value (X), N and Y is: X = Y·2-13
Bit Field (BIT)
An explanation of Bit Field is provided in “PMBus Commands Description” on page 29.
Custom (CUS)
An explanation of Custom data format is provided in “PMBus Commands Description” on page 29. A combination of Bit Field and
integer are common type of Custom data format.
ASCII (ASC)
A variable length string of text characters that uses the ASCII data format.
FN8670 Rev.5.00
Nov 8, 2017
Page 28 of 59
ISL8272M
PMBus Use Guidelines
The PMBus is a powerful tool that allows the user to optimize circuit performance by configuring devices for their application. When
configuring a device in a circuit, the device should be disabled whenever most settings are changed with PMBus commands. Some
exceptions to this recommendation are OPERATION, ON_OFF_CONFIG, CLEAR_FAULTS, VOUT_COMMAND, VOUT_MARGIN_HIGH,
VOUT_MARGIN_LOW, and ASCCR_CONFIG. While the device is enabled any command can be read. Many commands do not take effect
until after the device has been re-enabled, hence the recommendation that commands that change device settings are written while
the device is disabled.
When sending the STORE_DEFAULT_ALL, STORE_USER_ALL, RESTORE_DEFAULT_ALL, and RESTORE_USER_ALL commands, it is
recommended that no other commands are sent to the device for 100ms after sending STORE or RESTORE commands.
In addition, there should be a 2ms delay between repeated READ commands sent to the same device. When sending any other
command, a 5ms delay is recommended between repeated commands sent to the same device. Commands not listed in the PMBus
command summary are not allowed for customer use, and are reserved for factory use only. Issuing reserved commands may result in
unexpected operation.
Summary
All commands can be read at any time.
Always disable the device when writing commands that change device settings. Exceptions to this rule are commands intended to be
written while the device is enabled, for example, VOUT_MARGIN_HIGH.
To be sure a change to a device setting has taken effect, write the STORE_USER_ALL command, then cycle input power and re-enable.
PMBus Commands Description
OPERATION (01h)
Definition: Sets Enable, Disable, and VOUT Margin settings. OPERATION data values that force the margin high or low only take effect
when the MGN pin is left open (in the NOMINAL margin state).
Data Length in Bytes: 1
Data Format: BIT
Type: R/W
Default Value:
Units: N/A
SETTINGS
ACTIONS
04h
Immediate off (no sequencing)
44h
Soft off (with sequencing)
84h
On - Nominal
94h
On - Margin low
A4h
On - Margin high
ON_OFF_CONFIG (02h)
Definition: Configures the interpretation and coordination of the OPERATION command and the ENABLE pin (EN).
Data Length in Bytes: 1
Data Format: BIT
Type: R/W
Default Value: 16h (Device starts from ENABLE pin with soft off)
Units: N/A
SETTINGS
FN8670 Rev.5.00
Nov 8, 2017
ACTIONS
16h
Device starts from ENABLE pin with soft off.
17h
Device starts from ENABLE pin with immediate off.
1Ah
Device starts from OPERATION command with soft off.
1Bh
Device starts from OPERATION command with immediate off.
Page 29 of 59
ISL8272M
CLEAR_FAULTS (03h)
Definition: Clears all fault bits in all registers and releases the SALRT pin (if asserted) simultaneously. If a fault condition still exists, the
bit will reassert immediately. This command will not restart a device if it has shut down, it will only clear the faults.
Data Length in Bytes: 0 Byte
Data Format: N/A
Type: Write only
Default Value: N/A
Units: N/A
Reference: N/A
STORE_USER_ALL (15h)
Definition: Stores all PMBus settings from the operating memory to the nonvolatile USER store memory. To clear the USER store,
perform a RESTORE_FACTORY then STORE_USER_ALL. To add to the USER store, perform a RESTORE_USER_ALL, write commands to
be added, then STORE_USER_ALL. This command can be used during device operation, but the device will be unresponsive for 20ms
while storing values.
Data Length in Bytes: 0
Data Format: N/A
Type: Write only
Default Value: N/A
Units: N/A
RESTORE_USER_ALL (16h)
Definition: Restores all PMBus settings from the USER store memory to the operating memory. Command performed at power-up.
Security level is changed to Level 1 following this command. This command can be used during device operation, but the device will be
unresponsive for 20ms while storing values.
Data Length in Bytes: 0
Data Format: N/A
Type: Write only
Default Value: N/A
Units: N/A
VOUT_MODE (20h)
Definition: Reports the VOUT mode and provides the exponent used in calculating several VOUT settings. Fixed with linear mode with
default exponent (N) = -13
Data Length in Bytes: 1
Data Format: BIT
Type: Read-only
Default Value: 13h (Linear Mode, N = -13)
Units: N/A
VOUT_COMMAND (21h)
Definition: Sets or reports the target output voltage. This command cannot set a value higher than either VOUT_MAX or 110% of the pin
strap VOUT setting.
Data Length in Bytes: 2
Data Format: L16u
Type: R/W
Default Value: Pin strap setting
Units: Volts
Range: 0V to VOUT_MAX
FN8670 Rev.5.00
Nov 8, 2017
Page 30 of 59
ISL8272M
VOUT_CAL_OFFSET (23h)
Definition: Applies a fixed offset voltage to the output voltage command value. This command is typically used by the user to calibrate
a device in the application circuit.
Data Length in Bytes: 2
Data Format: L16s
Type: R/W
Default Value: 0000h
Units: Volts
VOUT_MAX (24h)
Definition: Sets an upper limit on the output voltage the unit can command regardless of any other commands or combinations. The
intent of this command is to provide a safeguard against a user accidentally setting the output voltage to a possibly destructive level
rather than to be the primary output overprotection. The default value can be changed using PMBus.
Data Length in Bytes: 2
Data Format: L16u
Type: R/W
Default Value: 1.10xVOUT_COMMAND pin strap setting
Units: Volts
Range: 0V to 5.5V
VOUT_MARGIN_HIGH (25h)
Definition: Sets the value of the VOUT during a margin high. The VOUT_MARGIN_HIGH command loads the unit with the voltage to which
the output is to be changed when the OPERATION command or MGN pin is set to “Margin High”.
Data Length in Bytes: 2
Data Format: L16u
Type: R/W
Default value: 1.05 x VOUT_COMMAND pin strap setting
Units: V
Range: 0V to VOUT_MAX
VOUT_MARGIN_LOW (26h)
Definition: Sets the value of the VOUT during a margin low. The VOUT_MARGIN_LOW command loads the unit with the voltage to which
the output is to be changed when the OPERATION command or MGN pin is set to “Margin Low”.
Data Length in Bytes: 2
Data Format: L16u
Type: R/W
Default value: 0.95 x VOUT_COMMAND pin strap setting
Units: V
Range: 0V to VOUT_MAX
VOUT_TRANSITION_RATE (27h)
Definition: Sets the rate at which the output should change voltage when the device receives the VOUT_COMMAND or an OPERATION
command (Margin High, Margin Low) that causes the output voltage to change. The maximum possible positive value of the two data
bytes indicates that the device should make the transition as quickly as possible.
Data Length in Bytes: 2
Data Format: L11
Type: R/W
Default value: BA00h (1.0 V/ms)
Units: V/ms
Range: 0.1 to 4V/ms
FN8670 Rev.5.00
Nov 8, 2017
Page 31 of 59
ISL8272M
VOUT_DROOP (28h)
Definition: Sets the effective load line (V/I slope) for the rail in which the device is used. It is the rate, in mV/A, at which the output
voltage decreases (or increases) with increasing (or decreasing) output current for use with Adaptive Voltage Positioning schemes or
multi-module current sharing. In the current sharing configuration, VOUT_DROOP set in each module stands for the droop seen by the
load.
Data Length in Bytes: 2
Data Format: L11
Type: R/W
Default value: Pin strap setting
Units: mV/A
Range: 0 to 40mV/A
FREQUENCY_SWITCH (33h)
Definition: Sets the switching frequency of the device. The initial default value is defined by a pin strap and this value can be overridden
by writing this command using PMBus. If an external SYNC is utilized, this value should be set as close as possible to the external clock
value. The output must be disabled when writing this command.
Data Length in Bytes: 2
Data Format: L11
Type: R/W
Default Value: Pin strap setting
Units: kHz
Range: 300kHz to 1066kHz
INTERLEAVE (37h)
Definition: Configures the phase offset of a device that is sharing a common SYNC clock with other devices. The phase offset of each
device can be set to any value between 0° and 360° in 22.5° increments. The internal two phases of the module always maintain a
phase difference of 180°.
Data Length in Bytes: 2
Data Format: BIT
Type: R/W
Default Value: 0000h
Units: N/A
BITS
PURPOSE
VALUE
15:4
Reserved
0
3:0
Position in Group
0 to 15
DESCRIPTION
Reserved
Sets position of the device's rail within the group.
IOUT_CAL_GAIN (38h)
Definition: Sets the effective impedance across the current sense circuit for use in calculating output current at +25°C.
Data Length in Bytes: 2
Data Format: L11
Type: R/W
Default Value: B370h (0.86mΩ)
Units: mΩ
IOUT_CAL_OFFSET (39h)
Definition: Used to null out any offsets in the output current sensing circuit and to compensate for delayed measurements of current
ramp due to Isense blanking time.
Data Length in Bytes: 2
Data Format: L11
Type: R/W
Default Value: 0000h (0A)
Units: A
FN8670 Rev.5.00
Nov 8, 2017
Page 32 of 59
ISL8272M
VOUT_OV_FAULT_LIMIT (40h)
Definition: Sets the VOUT overvoltage fault threshold.
Data Length in Bytes: 2
Data Format: L16u
Type: R/W
Default Value: 1.15xVOUT_COMMAND pin strap setting
Units: V
Range: 0V to VOUT_MAX
VOUT_OV_FAULT_RESPONSE (41h)
Definition: Configures the VOUT overvoltage fault response. Note that the device cannot be set to ignore this fault mode.
Data Length in Bytes: 1
Data Format: BIT
Type: R/W
Default Value: 80h (Disable and no retry)
Units: N/A
SETTINGS
ACTIONS
80h
Disable with no retry.
BFh
Disable and continuous retry with 70ms delay.
VOUT_OV_WARN_LIMIT (42h)
Definition: Sets the VOUT overvoltage warning threshold. The power-good signal is pulled low when output voltage goes higher than this
threshold.
Data Length in Bytes: 2
Data Format: L16u
Type: R/W
Default Value: 1.10xVOUT_COMMAND pin strap setting
Units: V
Range: 0V to VOUT_MAX
VOUT_UV_WARN_LIMIT (43h)
Definition: Sets the VOUT undervoltage warning threshold. The power-good signal is pulled low when output voltage goes lower than this
threshold.
Data Length in Bytes: 2
Data Format: L16u
Type: R/W
Default Value: 0.90xVOUT_COMMAND pin strap setting
Units: V
Range: 0V to VOUT_MAX
VOUT_UV_FAULT_LIMIT (44h)
Definition: Sets the VOUT undervoltage fault threshold. This fault is masked during ramp or when disabled.
Data Length in Bytes: 2
Data Format: L16u
Type: R/W
Default Value: 0.85xVOUT_COMMAND pin strap setting
Units: V
Range: 0V to VOUT_MAX
FN8670 Rev.5.00
Nov 8, 2017
Page 33 of 59
ISL8272M
VOUT_UV_FAULT_RESPONSE (45h)
Definition: Configures the VOUT undervoltage fault response.
Data Length in Bytes: 1
Data Format: BIT
Type: R/W
Default Value: 80h (Disable, no retry)
Units: N/A
SETTINGS
ACTIONS
80h
Disable with no retry.
BFh
Disable and continuous retry with 70ms delay.
IOUT_OC_FAULT_LIMIT (46h)
Definition: Sets the IOUT average overcurrent fault threshold. The device will automatically calculate the peak inductor overcurrent fault
limit for each phase based on the equation: IOUT(PEAK OC LIMIT) = (0.5*IOUT_OC_FAULT_LIMIT+0.5*IRIPPLE(P-P))*120%. A hard bound
of 42A is applied to the peak overcurrent fault limit per phase.
Data Length in Bytes: 2
Data Format: L11
Type: R/W
Default Value: E3C0h (60A)
Units: A
Range: -100 to 100A
IOUT_UC_FAULT_LIMIT (4Bh)
Definition: Sets the IOUT average undercurrent fault threshold. The device will automatically calculate the valley inductor undercurrent
fault limit for each phase based on the equation: IOUT(VALLEY UC LIMIT) = (0.5*IOUT_UC_FAULT_LIMIT-0.5*IRIPPLE(P-P))*120%. A hard
bound of -42A is applied to the valley undercurrent fault limit per phase.
Data Length in Bytes: 2
Data Format: L11
Type: R/W
Default Value: -1xIOUT_OC_FAULT_LIMIT
Units: A
Range: -100 to 100A
OT_FAULT_LIMIT (4Fh)
Definition: Sets the temperature at which the device should indicate an over-temperature fault. Note that the temperature must drop
below OT_WARN_LIMIT to clear this fault.
Data Length in Bytes: 2
Data Format: L11
Type: R/W
Default Value: EBE8h (+125˚C)
Units: Celsius
Range: 0°C to +175°C
FN8670 Rev.5.00
Nov 8, 2017
Page 34 of 59
ISL8272M
OT_FAULT_RESPONSE (50h)
Definition: Instructs the device on what action to take in response to an over-temperature fault.
Data Length in Bytes: 1
Data Format: BIT
Type: R/W
Fault Value: 80h (Disable and no retry)
Units: N/A
SETTINGS
ACTIONS
80h
Disable with no retry.
BFh
Disable and continuous retry with 70ms delay.
OT_WARN_LIMIT (51h)
Definition: Sets the temperature at which the device should indicate an over-temperature warning alarm. In response to the
OT_WARN_LIMIT being exceeded, the device sets the TEMPERATURE bit in STATUS_WORD, sets the OT_WARNING bit in
STATUS_TEMPERATURE, and notifies the host.
Data Length in Bytes: 2
Data Format: L11
Type: R/W
Default Value: EB48h (+105°C)
Units: Celsius
Range: 0°C to +175°C
UT_WARN_LIMIT (52h)
Definition: Sets the temperature at which the device should indicate an under-temperature warning alarm. In response to the
UT_WARN_LIMIT being exceeded, the device sets the TEMPERATURE bit in STATUS_WORD, sets the UT_WARNING bit in
STATUS_TEMPERATURE, and notifies the host.
Data Length in Bytes: 2
Data Format: L11
Type: R/W
Default Value: DC40h (-30°C)
Units: Celsius
Range: -55°C to +25°C
UT_FAULT_LIMIT (53h)
Definition: Sets the temperature, in degrees Celsius, of the unit where it should indicate an under-temperature fault. Note that the
temperature must rise above UT_WARN_LIMIT to clear this fault.
Data Length in Bytes: 2
Data Format: L11
Type: R/W
Default Value: E580h (-40°C)
Units: Celsius
Range: -55°C to +25°C
FN8670 Rev.5.00
Nov 8, 2017
Page 35 of 59
ISL8272M
UT_FAULT_RESPONSE (54h)
Definition: Configures the under-temperature fault response as defined by the following table. The delay time is the time between
restart attempts.
Data Length in Bytes: 1
Data Format: BIT
Type: R/W
Default Value: 80h (Disable, no retry)
Units: N/A
SETTINGS
ACTIONS
80h
Disable with no retry.
BFh
Disable and continuous retry with 70ms delay.
VIN_OV_FAULT_LIMIT (55h)
Definition: Sets the VIN overvoltage fault threshold.
Data Length in Bytes: 2
Data Format: L11
Type: R/W
Default Value: D380h (14V)
Units: V
Range: 0V to 16V
VIN_OV_FAULT_RESPONSE (56h)
Definition: Configures the VIN overvoltage fault response as defined by the following table. The delay time is the time between restart
attempts.
Data Length in Bytes: 1
Data Format: BIT
Type: R/W
Default Value: 80h (Disable and no retry)
Units: N/A
SETTINGS
ACTIONS
80h
Disable with no retry.
BFh
Disable and continuous retry with 70ms delay.
VIN_OV_WARN_LIMIT (57h)
Definition: Sets the VIN overvoltage warning threshold. In response to the OV_WARN_LIMIT being exceeded, the device sets the NONE
OF THE ABOVE and INPUT bits in STATUS_WORD, sets the VIN_OV_WARNING bit in STATUS_INPUT, and notifies the host.
Data Length in Bytes: 2
Data Format: L11
Type: R/W
Protectable: Yes
Default Value: D353h (13.3V)
Units: V
Range: 0V to 16V
FN8670 Rev.5.00
Nov 8, 2017
Page 36 of 59
ISL8272M
VIN_UV_WARN_LIMIT (58h)
Definition: Sets the VIN undervoltage warning threshold. If a VIN_UV_FAULT occurs, the input voltage must rise above
VIN_UV_WARN_LIMIT to clear the fault, which provides hysteresis to the fault threshold. In response to the UV_WARN_LIMIT being
exceeded, the device sets the NONE OF THE ABOVE and INPUT bits in STATUS_WORD, sets the VIN_UV_WARNING bit in STATUS_INPUT,
and notifies the host.
Data Length in Bytes: 2
Data Format: L11
Type: R/W
Default Value: 1.05 x VIN_UV_FAULT_LIMIT pin strap setting
Units: V
Range: 0V to 12V
VIN_UV_FAULT_LIMIT (59h)
Definition: Sets the VIN undervoltage fault threshold.
Data Length in Bytes: 2
Data Format: L11
Type: R/W
Default Value: Pin strap setting
Units: V
Range: 0V to 12V
VIN_UV_FAULT_RESPONSE (5Ah)
Definition: Configures the VIN undervoltage fault response as defined by the following table. The delay time is the time between restart
attempts.
Data Length in Bytes: 1
Data Format: BIT
Type: R/W
Default Value: 80h (Disable and no retry)
Units: N/A
SETTINGS
ACTIONS
80h
Disable with no retry
BFh
Disable and continuous retry with 70ms delay
POWER_GOOD_ON (5Eh)
Definition: Sets the voltage threshold for Power-good indication. Power-good asserts with a delay specified in POWER_GOOD_DELAY
after the output voltage exceeds POWER_GOOD_ON and deasserts when the output voltage is less than VOUT_UV_WARN_LIMIT.
Data Length in Bytes: 2
Data Format: L16u
Type: R/W
Default Value: 0.9xVOUT_COMMAND pin strap setting
Units: V
TON_DELAY (60h)
Definition: Sets the delay time from when the device is enabled to the start of VOUT rise.
Data Length in Bytes: 2
Data Format: L11
Type: R/W
Default Value: Pin strap setting
Units: ms
Range: 0 to 500ms
FN8670 Rev.5.00
Nov 8, 2017
Page 37 of 59
ISL8272M
TON_RISE (61h)
Definition: Sets the rise time of VOUT after ENABLE and TON_DELAY. In multi-module current sharing configuration where ASCR is
disabled for start up, the rise time of VOUT can be approximately calculated by Equation 1.
Data Length in Bytes: 2
Data Format: L11
Type: R/W
Default Value: Pin strap setting
Units: ms
Range: 0 to 200ms
TOFF_DELAY (64h)
Definition: Sets the delay time from DISABLE to the start of VOUT fall.
Data Length in Bytes: 2
Data Format: L11
Type: R/W
Default Value: Pin strap setting
Units: ms
Range: 0 to 500ms
TOFF_FALL (65h)
Definition: Sets the soft-off fall time for VOUT after DISABLE and TOFF_DELAY.
Data Length in Bytes: 2
Data Format: L11
Type: R/W
Default Value: Pin strap setting
Units: ms
Range: 0 to 200ms
STATUS_BYTE (78h)
Definition: Returns one byte of information with a summary of the most critical faults.
Data Length in Bytes: 1
Data Format: BIT
Type: Read-only
Default Value: 00h
Units: N/A
BIT NUMBER
STATUS BIT NAME
7
BUSY
6
OFF
5
VOUT_OV_FAULT
An output overvoltage fault has occurred.
4
IOUT_OC_FAULT
An output overcurrent fault has occurred.
3
VIN_UV_FAULT
An input undervoltage fault has occurred.
2
TEMPERATURE
A temperature fault or warning has occurred.
1
CML
0
NONE OF THE ABOVE
FN8670 Rev.5.00
Nov 8, 2017
MEANING
A fault was declared because the device was busy and unable to respond.
This bit is asserted if the unit is not providing power to the output, regardless of
the reason, including simply not being enabled.
A communications, memory or logic fault has occurred.
A fault or warning not listed in Bits 7:1 has occurred.
Page 38 of 59
ISL8272M
STATUS_WORD (79h)
Definition: Returns two bytes of information with a summary of the unit's fault condition. Based on the information in these bytes, the
host can get more information by reading the appropriate status registers. The low byte of the STATUS_WORD is the same register as
the STATUS_BYTE (78h) command.
Data Length in Bytes: 2
Data Format: BIT
Type: Read-only
Default Value: 0000h
Units: N/A
BIT NUMBER
STATUS BIT NAME
MEANING
15
VOUT
14
IOUT/POUT
13
INPUT
12
MFG_SPECIFIC
11
POWER_GOOD#
10
FANS
9
OTHER
8
UNKNOWN
7
BUSY
6
OFF
5
VOUT_OV_FAULT
An output overvoltage fault has occurred.
4
IOUT_OC_FAULT
An output overcurrent fault has occurred.
3
VIN_UV_FAULT
An input undervoltage fault has occurred.
2
TEMPERATURE
A temperature fault or warning has occurred.
1
CML
0
NONE OF THE ABOVE
An output voltage fault or warning has occurred.
An output current or output power fault or warning has occurred.
An input voltage, input current, or input power fault or warning has occurred.
A manufacturer specific fault or warning has occurred.
The POWER_GOOD signal, if present, is negated.
A fan or airflow fault or warning has occurred.
A bit in STATUS_OTHER is set.
A fault type not given in bits 15:1 of the STATUS_WORD has been detected.
A fault was declared because the device was busy and unable to respond.
This bit is asserted if the unit is not providing power to the output, regardless of
the reason, including simply not being enabled.
A communications, memory or logic fault has occurred.
A fault or warning not listed in Bits 7:1 has occurred.
STATUS_VOUT (7Ah)
Definition: Returns one data byte with the status of the output voltage.
Data Length in Bytes: 1
Data Format: BIT
Type: Read-only
Default Value: 00h
Units: N/A
BIT NUMBER
STATUS BIT NAME
7
VOUT_OV_FAULT
6
VOUT_OV_WARNING
Indicates an output overvoltage warning.
5
VOUT_UV_WARNING
Indicates an output undervoltage warning.
4
VOUT_UV_FAULT
3:0
N/A
FN8670 Rev.5.00
Nov 8, 2017
MEANING
Indicates an output overvoltage fault.
Indicates an output undervoltage fault.
These bits are not used.
Page 39 of 59
ISL8272M
STATUS_IOUT (7Bh)
Definition: Returns one data byte with the status of the output current.
Data Length in Bytes: 1
Data Format: BIT
Type: Read-only
Default Value: 00h
Units: N/A
BIT NUMBER
STATUS BIT NAME
MEANING
7
IOUT_OC_FAULT
6
IOUT_OC_LV_FAULT
An output overcurrent and low voltage fault has occurred.
An output overcurrent fault has occurred.
5
IOUT_OC_WARNING
An output overcurrent warning has occurred.
4
IOUT_UC_FAULT
3:0
N/A
An output undercurrent fault has occurred.
These bits are not used.
STATUS_INPUT (7Ch)
Definition: Returns input voltage and input current status information.
Data Length in Bytes: 1
Data Format: BIT
Type: Read-only
Default Value: 00h
Units: N/A
BIT NUMBER
STATUS BIT NAME
7
VIN_OV_FAULT
6
VIN_OV_WARNING
5
VIN_UV_WARNING
4
VIN_UV_FAULT
3:0
N/A
MEANING
An input overvoltage fault has occurred.
An input overvoltage warning has occurred.
An input undervoltage warning has occurred.
An input undervoltage fault has occurred.
These bits are not used.
STATUS_TEMP (7Dh)
Definition: Returns one byte of information with a summary of any temperature related faults or warnings.
Data Length in Bytes: 1
Data Format: BIT
Type: Read-only
Default Value: 00h
Units: N/A
BIT NUMBER
STATUS BIT NAME
MEANING
7
OT_FAULT
6
OT_WARNING
An over-temperature warning has occurred.
5
UT_WARNING
An under-temperature warning has occurred.
4
UT_FAULT
3:0
N/A
FN8670 Rev.5.00
Nov 8, 2017
An over-temperature fault has occurred.
An under-temperature fault has occurred.
These bits are not used.
Page 40 of 59
ISL8272M
STATUS_CML (7Eh)
Definition: Returns one byte of information with a summary of any communications, logic, and/or memory errors.
Data Length in Bytes: 1
Data Format: BIT
Type: Read-only
Default Value: 00h
Units: N/A
BIT NUMBER
MEANING
7
Invalid or unsupported PMBus command was received.
6
The PMBus command was sent with invalid or unsupported data.
5
4:2
packet error was detected in the PMBus command.
Not Used
1
A PMBus command tried to write to a read-only or protected command, or a communication fault other than the ones listed in
this table has occurred.
0
Not Used
STATUS_MFR_SPECIFIC (80h)
Definition: Returns one byte of information providing the status of the device's voltage monitoring and clock synchronization faults.
Data Length in Bytes: 1
Data Format: BIT
Type: Read only
Default value: 00h
Units: N/A
BIT NUMBER
FIELD NAME
7:6
Reserved
MEANING
Reserved.
5
VMON UV Warning
The voltage on the VMON pin has dropped below 4V.
4
VMON OV Warning
The voltage on the VMON pin has risen above 5.9V.
3
External Switching Period Fault
2
Reserved
1
VMON UV Fault
The voltage on the VMON pin has dropped below the level set by
VMON_UV_FAULT_LIMIT.
0
VMON OV Fault
The voltage on the VMON pin has risen above the level set by
VMON_OV_FAULT_LIMIT.
Loss of external clock synchronization has occurred.
Reserved.
READ_VIN (88h)
Definition: Returns the input voltage reading.
Data Length in Bytes: 2
Data Format: L11
Type: Read-only
Units: V
READ_VOUT (8Bh)
Definition: Returns the output voltage reading.
Data Length in Bytes: 2
Data Format: L16u
Type: Read-only
Units: V
FN8670 Rev.5.00
Nov 8, 2017
Page 41 of 59
ISL8272M
READ_IOUT (8Ch)
Definition: Returns the output current reading.
Data Length in Bytes: 2
Data Format: L11
Type: Read-only
Default Value: N/A
Units: A
READ_INTERNAL_TEMP (8Dh)
Definition: Returns the controller junction temperature reading from internal temperature sensor.
Data Length in Bytes: 2
Data Format: L11
Type: Read-only
Units: °C
READ_DUTY_CYCLE (94h)
Definition: Reports the actual duty cycle of the converter during the enable state.
Data Length in Bytes: 2
Data Format: L11
Type: Read only
Units: %
READ_FREQUENCY (95h)
Definition: Reports the actual switching frequency of the converter during the enable state.
Data Length in Bytes: 2
Data Format: L11
Type: Read only
Units: kHz
READ_IOUT_0 (96h)
Definition: Returns the Phase 1 current reading.
Data Length in Bytes: 2
Data Format: L11
Type: Read-only
Default Value: N/A
Units: A
READ_IOUT_1 (97h)
Definition: Returns the Phase 2 current reading.
Data Length in Bytes: 2
Data Format: L11
Type: Read-only
Default Value: N/A
Units: A
FN8670 Rev.5.00
Nov 8, 2017
Page 42 of 59
ISL8272M
MFR_ID (99h)
Definition: Sets user defined identification. The sum total of characters in MFR_ID, MFR_MODEL, MFR_REVISION, MFR_LOCATION,
MFR_DATE, MFR_SERIAL and USER_DATA_00 plus one byte per command cannot exceed 128 characters. This limitation includes
multiple writes of this command before a STORE command. To clear multiple writes, perform a RESTORE, write this command, then
perform a STORE/RESTORE.
Data Length in Bytes: user defined
Data Format: ASCII
Type: Block R/W
Default Value: null
Units: N/A
MFR_MODEL (9Ah)
Definition: Sets a user defined model. The sum total of characters in MFR_ID, MFR_MODEL, MFR_REVISION, MFR_LOCATION,
MFR_DATE, MFR_SERIAL, and USER_DATA_00 plus one byte per command cannot exceed 128 characters. This limitation includes
multiple writes of this command before a STORE command. To clear multiple writes, perform a RESTORE, write this command, then
perform a STORE/RESTORE.
Data Length in Bytes: user defined
Data Format: ASC
Type: Block R/W
Default Value: null
Units: N/A
MFR_REVISION (9Bh)
Definition: Sets a user defined revision. The sum total of characters in MFR_ID, MFR_MODEL, MFR_REVISION, MFR_LOCATION,
MFR_DATE, MFR_SERIAL, and USER_DATA_00 plus one byte per command cannot exceed 128 characters. This limitation includes
multiple writes of this command before a STORE command. To clear multiple writes, perform a RESTORE, write this command, then
perform a STORE/RESTORE.
Data Length in Bytes: user defined
Data Format: ASC
Type: Block R/W
Default Value: null
Units: N/A
MFR_LOCATION (9Ch)
Definition: Sets a user defined location identifier. The sum total of characters in MFR_ID, MFR_MODEL, MFR_REVISION,
MFR_LOCATION, MFR_DATE, MFR_SERIAL and USER_DATA_00 plus one byte per command cannot exceed 128 characters. This
limitation includes multiple writes of this command before a STORE command. To clear multiple writes, perform a RESTORE, write this
command, then perform a STORE/RESTORE.
Data Length in Bytes: User defined
Data Format: ASC
Type: Block R/W
Default Value: null
Units: N/A
MFR_DATE (9Dh)
Definition: Sets a user defined date. The sum total of characters in MFR_ID, MFR_MODEL, MFR_REVISION, MFR_LOCATION, MFR_DATE,
MFR_SERIAL and USER_DATA_00 plus one byte per command cannot exceed 128 characters. This limitation includes multiple writes
of this command before a STORE command. To clear multiple writes, perform a RESTORE, write this command, then perform a
STORE/RESTORE.
Data Length in Bytes: User defined
Data Format: ASC
Type: Block R/W
Default Value: null
Units: N/A
Reference: N/A
FN8670 Rev.5.00
Nov 8, 2017
Page 43 of 59
ISL8272M
MFR_SERIAL (9Eh)
Definition: Sets a user defined serialized identifier. The sum total of characters in MFR_ID, MFR_MODEL, MFR_REVISION,
MFR_LOCATION, MFR_DATE, MFR_SERIAL, and USER_DATA_00 plus one byte per command cannot exceed 128 characters. This
limitation includes multiple writes of this command before a STORE command. To clear multiple writes, perform a RESTORE, write this
command, then perform a STORE/RESTORE.
Data Length in Bytes: User defined
Data Format: ASC
Type: Block R/W
Default Value: null
Units: N/A
LEGACY_FAULT_GROUP (A8h)
Definition: Specifies which rail DDC IDs should be listened to for fault spreading with legacy devices. The data sent is a 4-byte, 32-bit, bit
vector where every bit represents a rail’s DDC ID. A bit set to 1 indicates a device DDC ID to which the configured device will respond
upon receiving a fault spreading event. In this vector, bit 0 of byte 0 corresponds to the rail with DDC ID 0. Following through, Bit 7 of
byte 3 corresponds to the rail with DDC ID 31.
Data Length in Bytes: 4
Data Format: BIT
Type: R/W
Default Value: 00000000h
USER_DATA_00 (B0h)
Definition: Sets user defined data. The sum total of characters in MFR_ID, MFR_MODEL, MFR_REVISION, MFR_LOCATION, MFR_DATE,
MFR_SERIAL, and USER_DATA_00 plus one byte per command cannot exceed 128 characters. This limitation includes multiple writes
of this command before a STORE command. To clear multiple writes, perform a RESTORE, write this command, then perform a
STORE/RESTORE.
Data Length in Bytes: User defined
Data Format: ASCII
Type: Block R/W
Default Value: null
Units: N/A
ISENSE_CONFIG (D0h)
Definition: Configures current sense circuitry.
Data Length in Bytes: 1
Data Format: BIT
Type: R/W
Default Value: 05h
Units: N/A
BIT
FIELD NAME
VALUE
7:4
Reserved
000
3:2
Current Sense
Blanking Time
1:0
Current Sense Range
FN8670 Rev.5.00
Nov 8, 2017
SETTING
DESCRIPTION
00
192ns
Sets the blanking time current sense blanking time.
01
256ns
10
412ns
11
640ns
00
Low Range
±25mV
01
Mid Range
±35mV
10
High Range
±50mV
11
Not Used
Page 44 of 59
ISL8272M
USER_CONFIG (D1h)
Definition: Configures several user-level features. This command overrides the CONFIG pin settings.
Data Length in Bytes: 1
Data Format: BIT
Type: R/W
Default Value: Pin strap setting
Units: N/A
BIT
7
FIELD NAME
ASCR on for Start up
VALUE
SETTING
0
Disabled
1
Enabled
6:5
Reserved
0
4:3
Ramp-Up and
Ramp-Down Minimum
Duty Cycle
00
0.39%
01
0.78%
2
1
Minimum Duty Cycle
Control
Power-Good Pin
Configuration
0
Reserved
DESCRIPTION
ASCR is disabled for start up. Use this for current sharing mode.
ASCR is enabled for start up. Use this for stand alone mode.
Reserved
10
1.17%
11
1.56%
0
Disable
1
Enable
0
Open Drain
1
Push-Pull
Sets the minimum duty-cycle during start-up and shutdown ramp.
Control for minimum duty cycle.
0 = PG is open drain output.
1 = PG is push-pull output.
0
DDC_CONFIG (D3h)
Definition: Configures DDC addressing and current sharing. With pin strap for stand alone configuration, the DDC rail ID is set according
to the SMBus address. With pin strap for multi-module current sharing, the DDC rail ID is set according to the number of devices. Device
position and number of devices in the rail can be programmed as needed.
Data Length in Bytes: 2
Data Format: BIT
Type: R/W
Default Value: Pin strap setting
Units: N/A
BIT
FIELD NAME
15:13
Device Position
12:8
Rail ID
7:4
Reserved
VALUE
0, 1, 2, 3
0
Device Internal Phase
Difference
0, 1
2:0
Number of Devices in
Rail
1, 3, 5, 7
DESCRIPTION
Sets the device position in a current sharing rail.
0-Position 1
1-Position 2
2-Position 3
3-Position 4
0 to 31 (00 to 1Fh)
3
FN8670 Rev.5.00
Nov 8, 2017
SETTING
Configures the DDC rail ID.
Reserved
Reserved
Sets the internal phase difference of the phase. The 0-phase difference is
180°. The 1-phase difference is 0°.
Identifies the number of devices in a current sharing rail.
1-standalone
3-two devices
5-three devices
7-four devices
Page 45 of 59
ISL8272M
POWER_GOOD_DELAY (D4h)
Definition: Sets the delay applied between the output exceeding the PG threshold (POWER_GOOD_ON) and asserting the PG pin. The
delay time can range from 0ms up to 500s, in steps of 125ns. A 1ms minimum configured value is recommended to apply proper
de-bounce to this signal.
Data Length in Bytes: 2
Data Format: L11
Type: R/W
Default Value: 3ms
Units: ms
Range: 0 to 5s
ASCR_CONFIG (DFh)
Definition: Allows user configuration of ASCR settings. ASCR Gain is analogous to bandwidth and ASCR Residual is analogous to
damping. To improve load transient response performance, increase ASCR Gain. To lower transient response overshoot, increase ASCR
Residual. Increasing ASCR gain can result in increased PWM jitter and should be evaluated in the application circuit. Excessive ASCR
gain can lead to excessive output voltage ripple. Increasing ASCR Residual to improve transient response damping can result in slower
recovery times, but will not affect the peak output voltage deviation. Typical ASCR Gain settings range from 50 to 1000 and ASCR
Residual settings range from 10 to 100.
Data Length in Bytes: 4
Data Format: CUS
Type: R/W
Default Value: Pin strap setting
BIT
31:25
24
PURPOSE
DATA Format
Unused
ASCR Enable
BIT
VALUE
DESCRIPTION
0000000h
Unused
1
Enable
0
Disable
23:16
ASCR Residual Setting
Integer
ASCR residual
15:0
ASCR Gain Setting
Integer
ASCR gain
SEQUENCE (E0h)
Definition: Identifies the Rail DDC ID of the prequel and sequel rails when performing multi-rail sequencing. The device will enable its
output when its EN or OPERATION enable states, as defined by ON_OFF_CONFIG, are set and the prequel device has issued a
Power-Good event on the DDC bus. The device will disable its output (using the programmed delay values) when the sequel device has
issued a Power-Down event on the DDC bus.
The data field is a two-byte value. The most-significant byte contains the 5-bit Rail DDC ID of the prequel device. The least-significant
byte contains the 5-bit Rail DDC ID of the sequel device. The most significant bit of each byte contains the enable of the prequel or
sequel mode. This command overrides the corresponding sequence configuration set by the CONFIG pin settings.
Data Length in Bytes: 2
Data Format: BIT
Type: R/W
Default Value: 0000h (Prequel and Sequel disabled)
BIT
15
FIELD NAME
Prequel Enable
14:13
Reserved
12:8
Prequel Rail DDC ID
7
Sequel Enable
6:5
Reserved
4:0
Sequel Rail DDC ID
FN8670 Rev.5.00
Nov 8, 2017
VALUE
SETTING
DESCRIPTION
0
Disable
Disable, no prequel preceding this rail.
1
Enable
Enable, prequel to this rail is defined by bits 12:8.
0
Reserved
0-31
DDC ID
Set to the DDC ID of the prequel rail.
Reserved
0
Disable
Disable, no sequel following this rail.
1
Enable
Enable, sequel to this rail is defined by bits 4:0.
0
Reserved
0-31
DDC ID
Reserved
Set to the DDC ID of the sequel rail.
Page 46 of 59
ISL8272M
DDC_GROUP (E2h)
Definition: Configures fault spreading group ID and enable, broadcast OPERATION group ID and enable, and broadcast
VOUT_COMMAND group ID and enable.
Data Length in Bytes: 3
Data Format: BIT
Type: R/W
Default Value: Pin strap setting (ignore BROADCAST VOUT_COMMAND, OPERATIONn and fault for stand alone operation. Enable
BROADCAST VOUT_COMMAND, OPERATION, and fault for current sharing).
BITS
23:22
PURPOSE
VALUE
Reserved
21
BROADCAST_VOUT_COMMAND Response
20:16
BROADCAST_VOUT_COMMAND Group ID
15:14
Reserved
13
BROADCAST_OPERATION Response
12:8
BROADCAST_OPERATION Group ID
7:6
5
4:0
0
Reserved
1
Responds to BROADCAST_VOUT_COMMAND with same Group ID.
0
Ignores BROADCAST_VOUT_COMMAND.
0-31d
Reserved
1
Responds to BROADCAST_OPERATION with same Group ID.
0
Ignores BROADCAST_OPERATION.
Group ID sent as data for broadcast BROADCAST_OPERATION events.
0
Reserved
1
Responds to POWER_FAIL events with same Group ID by shutting down
immediately.
0
Responds to POWER_FAIL events with same Group ID with sequenced shutdown.
POWER_FAIL Response
POWER_FAIL group ID
Group ID sent as data for broadcast BROADCAST_VOUT_COMMAND events.
0
0-31d
Reserved
DESCRIPTION
0-31d
Group ID sent as data for broadcast POWER_FAIL events.
DEVICE_ID (E4h)
Definition: Returns the 16-byte (character) device identifier string.
Data Length in Bytes: 16
Data Format: ASCII
Type: Block Read
Default Value: Part number/Die revision/Firmware revision
MFR_IOUT_OC_FAULT_RESPONSE (E5h)
Definition: Configures the IOUT overcurrent fault response as defined by the following table. The command format is the same as the
PMBus standard fault responses except that it sets the overcurrent status bit in STATUS_IOUT.
Data Length in Bytes: 1
Data Format: BIT
Type: R/W
Default Value: 80h (Disable and no retry)
Units: N/A
SETTINGS
FN8670 Rev.5.00
Nov 8, 2017
ACTIONS
80h
Disable with no retry.
BFh
Disable and continuous retry with 70ms delay.
Page 47 of 59
ISL8272M
MFR_IOUT_UC_FAULT_RESPONSE (E6h)
Definition: Configures the IOUT undercurrent fault response as defined by the following table. The command format is the same as the
PMBus standard fault responses except that it sets the undercurrent status bit in STATUS_IOUT.
Data Length in Bytes: 1
Data Format: BIT
Type: R/W
Default Value: 80h (Disable and no retry)
Units: N/A
SETTINGS
ACTIONS
80h
Disable with no retry.
BFh
Disable and continuous retry with 70ms delay.
SYNC_CONFIG (E9h)
Definition: Sets options for SYNC output configurations.
Data Length in Bytes: 1
Data Format: BIT
Type: R/W
Default Value: Pin strap setting
SETTINGS
00h
FN8670 Rev.5.00
Nov 8, 2017
ACTIONS
Use Internal clock. Clock frequency is set by pin strap or PMBus command.
02h
Use internal clock and output internal clock.
04h
Use external clock.
Page 48 of 59
ISL8272M
SNAPSHOT (EAh)
Definition: A 32-byte read-back of parametric and status values. It allows monitoring and status data to be stored to flash following a
fault condition. In case of a fault, the last updated values are stored to the flash memory. When the SNAPSHOT STATUS bit is set stored,
device will no longer automatically capture parametric and status values following fault until stored data are erased. Use the
SNAPSHOT_CONTROL command to erase store data and clear the status bit before next ramp up. Data erased is not allowed when the
module is enabled.
Data Length in Bytes: 32
Data Format: Bit field
Type: Block Read
BYTE NUMBER
31:23
VALUE
PMBUS COMMAND
FORMAT
Reserved
Reserved
00h
22
Flash Memory Status Byte
FF - Not Stored
00 - Stored
N/A
BIT
21
Manufacturer Specific Status Byte
STATUS_MFR_SPECIFIC (80h)
Byte
20
CML Status Byte
STATUS_CML (7Eh)
Byte
19
Temperature Status Byte
STATUS_TEMPERATURE (7Dh)
Byte
18
Input Status Byte
STATUS_INPUT (7Ch)
Byte
17
IOUT Status Byte
STATUS_IOUT (7Bh)
Byte
16
VOUT Status Byte
STATUS_VOUT (7Ah)
Byte
15:14
Switching Frequency
READ_FREQUENCY (95h)
L11
13:12
Reserved
Reserved
00h
11:10
Internal Temperature
READ_INTERNAL_TEMP (8Dh)
L11
9:8
Duty Cycle
READ_DUTY_CYCLE (94h)
L11
7:6
Highest Measured Output Current
N/A
L11
5:4
Output Current
READ_IOUT (8Ch)
L11
3:2
Output Voltage
READ_VOUT (8Bh)
L16u
1:0
Input Voltage
READ_VIN (88h)
L11
BLANK_PARAMS (EBh)
Definition: Returns a 16-byte string indicating which parameter values were either retrieved by the last RESTORE operation or have
been written since that time. Reading BLANK_PARAMS immediately after a restore operation allows the user to determine which
parameters are stored in that store. A one indicates the parameter is not present in the store and has not been written since the
RESTORE operation.
Data Length in Bytes: 16
Data Format: BIT
Type: Block Read
Default Value: FF…FFh
SNAPSHOT_CONTROL (F3h)
Definition: Writing a 01h will cause the device to copy the current SNAPSHOT values from NVRAM to the 32-byte SNAPSHOT command
parameter. Writing a 02h will cause the device to write the current SNAPSHOT values to NVRAM, and writing a 03h will erase all
SNAPSHOT values from NVRAM. Write (02h) and Erase (03h) may only be used when the device is disabled. All other values are
ignored.
Data Length in Bytes: 1
Data Format: Bit field
Type: R/W byte
VALUE
DESCRIPTION
01h
Read SNAPSHOT values from NV RAM
02h
Write SNAPSHOT values to NV RAM
03h
Erase SNAPSHOT values stored in NV RAM.
FN8670 Rev.5.00
Nov 8, 2017
Page 49 of 59
ISL8272M
RESTORE_FACTORY (F4h)
Definition: Restores the device to the hard-coded Factory default values and pin strap definitions. The device retains the DEFAULT and
USER stores for restoring. Security level is changed to Level 1 following this command.
Data Length in Bytes: 0
Data Format: N/A
Type: Write only
Default Value: N/A
Units: N/A
MFR_VMON_OV_FAULT_LIMIT (F5h)
Definition: Reads the VMON OV fault threshold.
Data Length in Bytes: 2
Data Format: L11
Type: Read only
Default Value: CB00h (6V)
Units: V
Range: 4V to 6V
MFR_VMON_UV_FAULT_LIMIT (F6h)
Definition: Reads the VMON UV fault threshold.
Data Length in Bytes: 2
Data Format: L11
Type: Read only
Default Value: CA00h (4V)
Units: V
Range: 4V to 6V
MFR_READ_VMON (F7h)
Definition: Reads the VMON voltage.
Data Length in Bytes: 2
Data Format: L11
Type: Read only
Default Value: N/A
Units: V
Range: 4V to 6V
VMON_OV_FAULT_RESPONSE (F8h)
Definition: Reads the VMON OV fault response.
Data Length in Bytes: 1
Data Format: BIT
Type: Read only
Default Value: 80h (Disable and no retry)
Units:
VMON_UV_FAULT_RESPONSE (F9h)
Definition: Reads the VMON UV fault response, which follows VIN_UV_FAULT_RESPONSE.
Data Length in Bytes: 1
Data Format: BIT
Type: Read only
Default Value: 80h (Disable and no retry)
Units: V
FN8670 Rev.5.00
Nov 8, 2017
Page 50 of 59
ISL8272M
Firmware Revision History
TABLE 10. ISL8272M NOMENCLATURE GUIDE
CHANGE DESCRIPTION
NOTE
ISL8272-000-FC02
FIRMWARE REVISION CODE
- Enhanced fault management during start-up
- Enhanced IOUT UC fault management during start-up
- Enhanced PMBus immunity to noise and lockup
- Added paged ISENGain and ISENOffset factors which are storable in default
memory
- Added temperature compensation for the paged ISENGain and ISENOffset factors
and reduced temperature drift
- Improved intra-device current balance within the two internal phases
- Fixed the synchronization issue during VOUT_COMMAND change on-the-fly current
sharing conditions
- Added more pin-strap resistor settings for the CS pin for four-module current
sharing conditions
- Added the capability to change the device internal phase difference from 180° to
0° in DDC_CONFIG and optimized module-to-module phase shift in Current Sharing
mode
- VMON UV/OV warning value changed
Recommended for new designs
ISL8272-000-FC01
Initial Release
Not recommended for new
designs
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted.
Please visit our website to make sure you have the latest revision.
DATE
REVISION
CHANGE
Nov 8, 2017 FN8670.5 Added clock configurations to Table 9, Current Sharing Resistor Settings on page 22.
STATUS_MFR_SPECIFIC (80h) PMBus command on page 41 - updated command definition and the meanings of Bits 4 and 5.
DDC_CONFIG (D3h) PMBus command on page 45 - updated bit descriptions.
Added Firmware Revision B (FC02) to Firmware Revision History on page 51 and firmware graphic on page 3.
Renumbered figures to fix issue in which Figure 4 was listed twice.
Mar 31, 2017 FN8670.4 Related Literature on page 1 updated.
Ordering Information, page 3: Updated Note 2 - added Tape and Reel option and Note 3 - added exemptions 7C-I and 7A.
Added the notation "A standard 1% resistor is required" to the following sections:
-Soft-Start/Stop Delay and Ramp Times, Switching Frequency and PLL, Loop Compensation, Input Undervoltage Lockout
(UVLO), SMBus Module Address Selection, Active Current Sharing
Added "Note that fault retry is not supported in the current sharing configuration." to the following sections:
Input Undervoltage Lockout (UVLO), Output Overvoltage Protection, Output Overcurrent Protection, Thermal Overload
Protection, Active Current Sharing,
Fault Spreading ("Note that fault retry is not supported in multiple modules with fault spreading enabled, such as the current
sharing configuration.").
SMBus Communications section on page 17, paragraph added (3rd paragraph)
Soft-Start/Stop Delay and Ramp Times section page 17– a paragraph was added (1st paragraph)
PMBus Use Guidelines - added "Commands not listed in the PMBus command summary are not allowed for customer use,
and are reserved for factory use only. Issuing reserved commands may result in unexpected operation."
POD Y58.18x23 revised from rev 1 to rev 3. Changes since rev 1:
1) Pages 1 and 2 of POD Y58.18x23 remain unchanged for this update. 2) Deleted remaining pages 3-5 of existing POD and
replaced with: New drawings - 2 drawings per page
On page 2, In the "Size Details for the 16 Exposed Pads" (Bottom View) changed dimension 8.40 (2X) to 8.30 (2x) and 8.00
(2x) to 1.00 (2X).
Mar 16, 2016 FN8670.3 Added “PMBus Use Guidelines” on page 29.
Updated POD Y58.18x23 to the latest revision changes are as follows:
-Detail A on page 1: Added Reference Radius for rounded corners on small I/O pads.
Jan 14, 2015 FN8670.2 “Electrical Specifications” on page 10 under VOUT_ACCY and VOUT_READ_ERR: Updated unit value from “% FS” to “%VOUT”.
Updated “Switching Frequency and PLL” on page 18.
Sep 17, 2014 FN8670.1 Removed the words “in forced CCM Mode” from 2nd paragraph on page 1, which read “The ISL8272M operated in forced CCM
Mode with the ChargeMode™ control architecture,...
Sep 12, 2014 FN8670.0 Initial release
FN8670 Rev.5.00
Nov 8, 2017
Page 51 of 59
ISL8272M
About Intersil
Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products
address some of the largest markets within the industrial and infrastructure, mobile computing, and high-end consumer markets.
For the most updated datasheet, application notes, related documentation and related parts, please see the respective product
information page found at www.intersil.com.
For a listing of definitions and abbreviations of common terms used in our documents, visit: www.intersil.com/glossary.
You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask.
Reliability reports are also available from our website at www.intersil.com/support.
© Copyright Intersil Americas LLC 2014-2017. All Rights Reserved.
All trademarks and registered trademarks are the property of their respective owners.
For additional products, see www.intersil.com/en/products.html
Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted
in the quality certifications found at www.intersil.com/en/support/qualandreliability.html
Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such
modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are
current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its
subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN8670 Rev.5.00
Nov 8, 2017
Page 52 of 59
For the most recent package outline drawing, see Y58.18x23.
Y58.18x23
58 I/O 18mmx23mmx7.5mm CUSTOM HDA MODULE
Rev 3, 12/16
18.00
A
DATUM A
B
18 17 16 1514 13 12 1110 9 8 7 6 5 4 3 2 1
TERMINAL #A1
INDEX AREA
(9x11.5)
12.00
23.00
0.10 M C A B
22.60 ± 0.15
0.10 C 2X
0.40 REF
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
V
W
Y
AA
AB
AC
PIN A1 INDICATOR
C = 0.35
SEE DETAIL A
DATUM B
16.00
0.10 C 2X
17.20
TOP VIEW
0.10 M C A B
BOTTOM VIEW
7.50 MAX
0.10 C
2
0.20 REF
1.00
0.20 REF
SEATING PLANE
0.08 C
C
MAX 0.025
SIDE VIEW
NOTES:
Page 53 of 59
1.
All dimensions are in millimeters.
2.
Represents the basic land grid pitch.
3.
These 42 I/Os are centered in a fixed row and column matrix
at 1.0mm pitch BSC.
42 x 0.60 ± 0.05
4.
Dimensioning and tolerancing per ASME Y14.5-2009.
3
5.
Tolerance for exposed PAD edge location dimension on
page 3 is ±0.1mm.
3
42 x 0.60 ± 0.05
0.10 M C A B
0.05 M C
TERMINAL TIP
0.100 R REF
1.00
DETAIL A
2
ISL8272M
FN8670 Rev.5.00
Nov 8, 2017
Package Outline Drawing
8.20
8.80
6.80
7.20
7.80
5.80
6.20
4.20
4.80
5.20
3.20
3.80
2.20
2.80
0.50
1.20
1.80
0.80
0.20
2.80
2.20
1.80
1.20
0.50
0.20
0.80
4.20
3.80
3.20
6.20
5.20
4.80
1.00 (2X)
5.80
8.80
1.00 (2X)
7.20
7.80
ISL8272M
FN8670 Rev.5.00
Nov 8, 2017
8.30 (2X)
11.30
11.30
1.60 (2X)
4.80 (2X)
8.70
2.60
9.70
9.30
9.10
9.70 9.30
9.10
7.70
6.70
6.50 6.30
5.50 5.70
4.70 5.30
4.30
3.70
3.30
2.70
2.00 2.30
1.70
1.30
0.70
0.30
0.30
0.70
1.30
1.70
2.30
2.70 2.90
3.30
4.00
7.70
6.70 7.30
6.30 6.50
5.70 5.50
5.30
4.70
6.00
6.00
7.30
4.40
3.50 (2X)
4.60
1.00 (2X)
2.30
1.30
1.60 (2X)
3.40
3.60
2.20
1.10
1.10 (2X)
4.40
2.00
1.30
1.00
2.30
5.00 (2X)
8.10
8.10
9.30
9.30
2.00 (2X)
1.60 (2X)
9.70
11.30
Page 54 of 59
SIZE DETAILS FOR THE 16 EXPOSED PADS
TERMINAL AND PAD EDGE DETAILS
BOTTOM VIEW
8.60
6.40 6.00
6.50
5.20
4.40
3.60
2.40
2.00
1.80
1.20 0.80
0.20
0.40 0.00
4.60
3.00
2.60
0.60
3.80
6.40
8.60
5.60
5.40
6.20
7.40
7.00
7.20
5.60
2.20
6.60
11.30
4.00 (2X)
1.40 (2X)
2.90
4.00
0.80 (2X)
5.30 (2X)
0.70
0.00
5.10
4.20
2.10 (2X)
4.30
3.70
6.30
8.50
9.70
9.000
5.785
5.215
4.785
4.215
3.785
3.215
2.785
2.215
1.785
1.215
0.785
0.215
0.000
0.215
0.785
1.215
1.785
2.215
2.785
3.215
3.785
4.215
4.785
5.215
5.785
6.215
6.785
7.785
7.215
6.785
6.215
1.390
1.710
2.500
2.820
3.895
4.215
5.290
5.610
6.400
6.720
7.510
7.830
8.770
9.000
9.000
8.770
8.450
7.830
7.510
6.720
6.400
5.610
5.290
4.215
3.895
2.820
2.500
1.710
1.390
0.530
0.000
0.530
11.500
11.270
11.500
11.270
9.730
9.410
9.730
9.410
8.130
7.810
8.130
7.810
6.530
6.530
5.470
5.470
3.910
3.590
3.910
3.590
2.030
2.030
0.000
0.000
ISL8272M
FN8670 Rev.5.00
Nov 8, 2017
9.000
Stencil opening center position
11.500
11.500
9.285
8.715
8.285
7.715
7.285
6.715
6.285
5.715
5.285
4.715
4.285
3.715
3.285
2.715
2.285
1.715
1.285
0.715
0.285
0.000
0.285
0.715
1.285
1.715
2.285
2.715
3.285
9.285
8.715
8.285
7.715
7.285
6.715
6.285
5.715
5.285
4.715
4.285
3.715
1.285
0.715
0.285
0.000
0.285
0.715
1.285
2.715
3.285
Page 55 of 59
STENCIL OPENING EDGE POSITION - 1
11.500
STENCIL OPENING EDGE POSITION - 2
9.000
6.215
6.785
7.215
7.785
0.000
1.215
1.785
1.785
1.215
4.785
4.215
3.785
3.215
11.500
9.000
8.785
8.215
9.000
0.000
0.230
0.770
1.230
1.910
2.230
2.910
3.230
3.910
4.230
4.910
5.230
5.910
6.230
6.910
7.790
8.110
9.490
9.730
9.810
11.270
11.500
7.660
7.340
6.430
5.970
5.240
4.920
4.190
3.870
3.140
2.820
2.090
6.330
7.510
7.830
8.640
8.960
9.730
9.770
10.090
11.270
11.500
9.000
8.570
6.330
Stencil opening edge
9.000
7.170
6.230
0.000
6.230
7.170
9.000
9.000
2.770
1.875
1.555
0.660
0.340
0.000
0.555
0.875
1.770
9.000
ISL8272M
FN8670 Rev.5.00
Nov 8, 2017
11.500
11.500
11.500
11.500
9.070
9.070
6.670
5.825
5.505
4.660
4.340
3.495
3.175
2.330
0.000
0.000
7.960
7.960
7.640
6.530
7.640
6.530
0.000
0.000
2.930
3.840
4.030
4.160
5.070
2.930
3.840
4.160
5.070
6.030
6.890
7.210
8.070
6.030
6.705
6.330
Page 56 of 59
STENCIL OPENING EDGE POSITION - 3
8.530
9.270
11.500
11.500
7.700
7.025
8.020
STENCIL OPENING EDGE POSITION - 4
8.570
9.000
6.970
7.230
3.770
4.090
4.570
5.430
1.840
2.160
0.000
0.230
3.430
3.110
2.430
8.570
7.060
6.740
6.110
5.430
5.230
5.110
4.430
4.110
9.280
9.600
10.275
10.595
11.270
11.500
9.000
9.000
6.570
4.890
5.570
5.890
0.000
1.160
1.670
1.990
2.570
2.890
3.570
3.890
4.570
5.970
5.240
4.920
4.430
4.190
3.870
3.140
2.820
2.090
9.000
11.500
7.640
7.960
8.530
9.270
PCB layout pattern
0.000
0.000
5.320
5.580
6.430
6.690
7.540
7.800
8.800
9.000
3.925
4.185
4.185
3.925
2.790
2.530
1.680
1.420
0.500
0.000
0.500
1.420
1.680
2.530
2.790
9.000
8.800
8.450
7.800
7.540
6.690
6.430
5.580
5.320
9.000
9.000
0.000
ISL8272M
FN8670 Rev.5.00
Nov 8, 2017
11.500
11.500
11.500
11.300
11.500
10.950
9.700
9.440
9.700
9.440
8.100
7.840
8.100
7.840
6.500
6.500
5.500
5.500
3.880
3.620
3.880
3.620
2.000
2.000
0.000
0.000
1.030
2.270
4.030
5.070
Page 57 of 59
STENCIL OPENING EDGE POSITION - 5
6.300
6.300
7.540
7.800
8.670
8.930
9.700
9.800
10.060
11.300
11.500
7.820
8.080
9.520
9.700
9.780
PCB LAND PATTERN - 1 (FOR REFERENCE)
9.000
0.000
0.200
0.800
1.200
1.940
2.200
2.940
3.200
3.940
4.200
4.940
5.200
5.940
6.200
6.940
7.630
7.370
6.400
6.000
5.210
4.950
4.160
3.900
3.110
2.850
2.060
11.300
11.500
9.000
8.600
9.000
3.760
4.080
4.810
5.130
5.860
6.180
6.910
3.030
2.030
1.770
0.430
0.000
4.910
4.430
3.570
11.500
6.530
9.280
9.600
10.275
10.595
11.270
11.500
7.810
7.490
6.030
6.890
7.210
8.070
9.000
8.770
6.030
6.705
7.025
7.700
8.020
11.500
9.300
8.700
8.300
7.700
7.300
6.700
6.300
5.700
5.300
4.700
4.300
3.700
3.300
2.700
2.300
1.700
1.300
0.700
0.300
0.000
0.300
0.700
1.300
1.700
2.300
2.700
3.300
9.300
8.700
8.300
7.700
7.300
6.700
6.300
5.700
5.300
4.700
4.300
3.700
1.300
0.700
0.300
0.000
0.300
0.700
1.300
2.700
3.300
9.000
2.800
1.845
1.585
0.630
0.370
0.000
0.585
0.845
1.800
9.000
0.000
9.000
6.800
6.200
5.800
5.200
4.800
4.200
3.800
3.200
2.800
2.200
1.800
1.200
0.800
0.200
0.200
0.800
1.200
1.800
2.200
2.800
3.200
3.800
4.200
4.800
5.200
5.800
6.200
6.800
7.800
7.200
9.000
8.800
8.200
ISL8272M
FN8670 Rev.5.00
Nov 8, 2017
11.500
11.500
11.500
6.700
5.795
5.535
4.630
4.370
3.465
3.205
2.300
0.000
0.000
6.000
6.920
7.180
8.100
6.300
7.670
7.930
8.500
9.300
Page 58 of 59
PCB LAND PATTERN - 2 (FOR REFERENCE)
11.500
PCB LAND PATTERN - 3 (FOR REFERENCE)
9.000
0.000
1.060
1.700
1.960
2.600
2.860
3.600
3.860
4.600
4.860
5.600
5.860
6.600
6.000
5.210
4.950
4.160
3.900
3.110
2.850
2.060
11.500
9.000
9.000
6.200
6.800
7.200
7.800
3.200
3.800
4.200
4.800
0.000
0.200
0.800
1.200
1.800
1.800
1.200
4.800
4.200
3.800
3.200
11.500
9.000
11.500
11.500
9.100
9.100
7.930
7.670
7.930
7.670
6.500
6.500
0.000
0.000
9.000
0.000
9.000
7.200
6.200
0.000
6.200
7.200
9.000
ISL8272M
FN8670 Rev.5.00
Nov 8, 2017
11.500
11.500
11.500
0.000
0.000
1.000
PCB LAND PATTERN - 4 (FOR REFERENCE)
9.310
9.570
10.305
10.565
11.300
11.500
9.310
9.570
10.305
10.565
11.300
11.500
6.000
6.920
7.180
8.100
PCB LAND PATTERN - 5 (FOR REFERENCE)
9.000
3.000
3.790
4.050
4.840
5.100
5.890
6.150
6.940
0.400
0.000
11.500
2.000
1.800
8.600
9.000
7.000
7.200
3.800
4.060
4.600
5.400
1.870
2.130
0.000
0.200
7.030
6.770
6.140
5.400
5.200
5.140
4.400
4.140
3.400
3.140
2.400
9.000
8.600
11.500
6.000
6.735
6.995
7.730
7.990
5.100
3.600
9.300
6.000
6.735
6.995
7.730
7.990
4.940
4.400
8.500
4.000
6.500
3.870
4.130
5.100
2.300
2.900
3.870
4.000
4.130
5.100
9.000
8.800
7.780
7.520
2.900
Page 59 of 59