SAW BANDPASS FILTER ACT PART NO.: ACTFG001-1575.42M-1411 Product Type: Customer: SAW Filter Description: GPS Filter. PREPARED BY Customer Part NO.: Issued Date: 02/07/2015 CHECKED BY APPROVED BY Features SAW filter for GPS. 1 High stability and reliability with good performance and no adjustment. 2 Narrow and sharp pass band characteristics. RoHS compatible. 3 Low insertion loss and deep stop band attenuation for interference. 4 Low – loss SAW filter for GPS. 5 Package size 1.4*1.1 Package Dimensions Ceramic Package: Unit：mm Pin Configuration 1 Input 4 Output 2,3,5 Ground Marking Top View, Laser Printing Code 2015 2016 2017 2018 1 a n A N 2 b p B P ” 1”: “G1”: Part number “＊”: Lot number (The code shown below varies in a 4-year cycle) 3 c q C Q 4 d r D R 5 e s E S 6 f t F T 7 g u G U 8 h v H V 9 i w J W Terminal 1 10 j x K X Maximum Ratings Rating Value Unit VDC 10 V RF Power (in BW) P 10 dBm Operating Temperature Range TA -40 ~ +85 °C Storage Temperature Range Tstg -40 ~ +85 °C DC Voltage (between any Terminals) -2- 11 k y L Y 12 m z M Z Electrical Characteristics: Item Minimum Typical Maximum Unit Center Frequency fC - 1575.42 - MHz Insertion Loss in 1574.42–1576.42MHz IL - 1.2 1.5 dB 0.1 0.5 dB Amplitude Variation in 1574.42–1576.42MHz Absolute Attenuation α 0.30 … 1450.0MHz 35 39 - dB 1450.0 …1525.0 MHz 38 45 - dB 1620.0 … 1640.0 MHz 45 48 - dB 1640.0 … 1805.0MHz 38 40 1805.0 …1910.0 MHz 38 40 -- dB 1910.0 …2000.0 MHz 38 43 -- dB 2000.0 …4000.0 MHz 30 45 -- dB 4000.0 …6000.0 MHz 20 22 -- dB - 1.15 1.5 VSWR in 1574.42–1576.42MHz RoHS Compliant Typical Frequency Response Electrostatic Sensitive Device -3- dB -4- Packing Information Carrier Tape Reel Dimensions -5- Stability Characteristics Test item Condition of test 1 Mechanical shock (a) Drops: 3 times on concrete floor (b) Height: 1.0 m 2 Vibration resistance (a) Frequency of vibration: 10~55Hz (c) Directions: X,Y and Z 3 Moisture resistance (a) Condition: 40℃±2℃ , 93+2 -3% RH. (b) Duration: 96 hours (c) Wait 4 hours before measurement 4 Climatic sequence (a) +70°C for 16 hours (b) +55°C for 24 hours, 90~95% R.H. (c) -25°C for 2 hours (d) +40°C for 24 hours, 90~95% R.H. (e) Wait 4 hours before measurement 5 High temperature exposure (a) Temperature: 85°C (c) Wait 4 hours before measurement Temperature cycling (a) +85°C for 30 minutes ⇒ -40°C for 30 minutes repeated 120 times (b) Wait 4 hours before measurement 6 (b) Amplitude: 1.5 mm (d) Duration: 2 hours (b) Duration: 250 hours Requirements: The SAW filer shall remain within the electrical specifications after tests. Remarks SAW devices should not be used in any type of fluid such as water, oil, organic solvent, etc. Be certain not to apply voltage exceeding the rated voltage of components. Do not operate outside the recommended operating temperature range of components. Sudden change of temperature shall be avoided, deterioration of the characteristics can occur. Be careful of soldering temperature and duration of components when soldering. Do not place soldering iron on the body of components. Be careful not to subject the terminals or leads of components to excessive force. SAW devices are electrostatic sensitive. Please avoid static voltage during operation and storage. Ultrasonic cleaning shall be avoided. Ultrasonic vibration may cause destruction of components. Test Circuit 50Ω -6- Recommended Soldering Profile C ACT 2015. All Rights Reserved. ○ E 1. 2. 3. A The specifications of this device are subject to change or obsolescence without notice. Typically, equipment utilizing this device requires emissions testing and government approval, which is the responsibility of the equipment manufacturer. Our liability is only assumed for the Surface Acoustic Wave (SAW) component(s) per se, not for applications, processes and circuits implemented within components or assemblies. -7-