STMicroelectronics LF55ABP Very low drop voltage regulators with inhibit Datasheet

LF00
SERIES
VERY LOW DROP
VOLTAGE REGULATORS WITH INHIBIT
■
■
■
■
■
■
■
■
■
■
VERY LOW DROPOUT VOLTAGE (0.45V)
VERY LOW QUIESCENT CURRENT (TYP.
50 µA IN OFF MODE, 500 µA IN ON MODE)
OUTPUT CURRENT UP TO 500 mA
LOGIC-CONTROLLED ELECTRONIC
SHUTDOWN
OUTPUT VOLTAGES OF 1.25; 1.5; 1.8; 2.5;
2.7; 3; 3.3; 3.5; 4; 4.5; 4.7; 5; 5.2; 5.5; 6; 8;
8.5; 9; 12V
INTERNAL CURRENT AND THERMAL LIMIT
ONLY 2.2 µF FOR STABILITY
AVAILABLE IN ± 1% (AB) OR ± 2% (C)
SELECTION AT 25 °C
SUPPLY VOLTAGE REJECTION: 80db (TYP.)
TEMPERATURE RANGE: -40 TO 125 °C
DESCRIPTION
The LF00 series are very Low Drop regulators
available in PENTAWATT, TO-220, TO-220FP,
DPAK and PPAK package and in a wide range of
output voltages.
The very Low Drop voltage (0.45V) and the very
low quiescent current make them particularly
suitable for Low Noise, Low Power applications
and specially in battery powered systems.
In the 5 pins configuration (PENTAWATT and
PPAK) a Shutdown Logic Control function is
available (pin 2, TTL compatible). This means that
SCHEMATIC DIAGRAM
August 2003
PENTAWATT
TO-220
PPAK
TO-220FP
DPAK
when the device is used as a local regulator, it is
possible to put a part of the board in standby,
decreasing the total power consumption. In the
three terminal configuration the device has the
same electrical performance, but is fixed in the ON
state. It requires only a 2.2 µF capacitor for
stability allowing space and cost saving.
1/34
LF00 SERIES
ABSOLUTE MAXIMUM RATINGS
Symbol
Parameter
Value
Unit
-0.5 to 40 (*)
V
VI
DC Input Voltage
IO
Output Current
Internally Limited
Ptot
Power Dissipation
Internally Limited
Tstg
Storage Temperature Range
-40 to 150
°C
Top
Operating Junction Temperature Range
-40 to 125
°C
(*) For 18 < VIN < 40 the regulator is in shut-down
THERMAL DATA
Symbol
Parameter
PENTAWATT
TO-220
TO-220FP
DPAK/PPAK
Unit
Rthj-case
Thermal Resistance Junction-case
3
3
5
8
°C/W
Rthj-amb
Thermal Resistance Junction-ambient
50
50
60
100
°C/W
CONNECTION DIAGRAM (top view)
TO-220
TO-220FP
PPAK
DPAK
PENTAWATT
2/34
LF00 SERIES
ORDERING CODES
TYPE
PENTAWATT
TO-220
TO-220FP
DPAK (#)
PPAK (#)
OUTPUT
VOLTAGE
LF12C (*)
LF12AB (*)
LF15C
LF15AB
LF18C
LF18AB
LF25C
LF25AB
LF27C
LF27AB
LF30C
LF30AB
LF33C
LF33AB
LF35C
LF35AB
LF40C
LF40AB
LF45C (*)
LF45AB (*)
LF47C
LF47AB
LF50C
LF50AB
LF52C
LF52AB
LF55C
LF55AB
LF60C
LF60AB
LF80C
LF80AB
LF85C
LF85AB
LF90C
LF90AB
LF120C
LF120AB
LF12CV5V
LF12ABV5V
LF15CV5V (*)
LF15ABV5V (*)
LF18CV5V
LF18ABV5V
LF25CV5V
LF25ABV5V
LF27CV5V
LF27ABV5V
LF30CV5V
LF30ABV5V
LF33CV5V
LF33ABV5V
LF35CV5V
LF35ABV5V
LF40CV5V
LF40ABV5V
LF45CV5V
LF45ABV5V
LF47CV5V
LF47ABV5V
LF50CV5V
LF50ABV5V
LF52CV5V
LF52ABV5V
LF55CV5V
LF55ABV5V
LF60CV5V
LF60ABV5V
LF80CV5V
LF80ABV5V
LF85CV5V
LF85ABV5V
LF90CV5V
LF90ABV5V
LF120CV5V
LF120ABV5V
LF12CV
LF12ABV
LF15CV (*)
LF15ABV (*)
LF18CV
LF18ABV
LF25CV
LF25ABV
LF27CV
LF27ABV
LF30CV
LF30ABV
LF33CV
LF33ABV
LF35CV
LF35ABV
LF40CV
LF40ABV
LF45CV
LF45ABV
LF47CV
LF47ABV
LF50CV
LF50ABV
LF52CV
LF52ABV
LF55CV
LF55ABV
LF60CV
LF60ABV
LF80CV
LF80ABV
LF85CV
LF85ABV
LF90CV
LF90ABV
LF120CV
LF120ABV
LF12CP
LF12ABP
LF15CP (*)
LF15ABP (*)
LF18CP
LF18ABP
LF25CP
LF25ABP
LF27CP
LF27ABP
LF30CP
LF30ABP
LF33CP
LF33ABP
LF35CP
LF35ABP
LF40CP
LF40ABP
LF45CP
LF45ABP
LF47CP
LF47ABP
LF50CP
LF50ABP
LF52CP
LF52ABP
LF55CP
LF55ABP
LF60CP
LF60ABP
LF80CP
LF80ABP
LF85CP
LF85ABP
LF90CP
LF90ABP
LF120CP
LF120ABP
LF12CDT
LF12ABDT
LF15CDT
LF15ABDT
LF18CDT
LF18ABDT
LF25CDT
LF25ABDT
LF27CDT
LF27ABDT
LF30CDT
LF30ABDT
LF33CDT
LF33ABDT
LF35CDT
LF35ABDT
LF40CDT
LF40ABDT
LF45CDT
LF45ABDT
LF47CDT
LF47ABDT
LF50CDT
LF50ABDT
LF52CDT
LF52ABDT
LF55CDT
LF55ABDT
LF60CDT
LF60ABDT
LF80CDT
LF80ABDT
LF85CDT
LF85ABDT
LF90CDT
LF90ABDT
LF120CDT
LF120ABDT
LF12CPT
LF12ABPT
LF15CPT (*)
LF15ABPT (*)
LF18CPT
LF18ABPT
LF25CPT
LF25ABPT
LF27CPT
LF27ABPT
LF30CPT
LF30ABPT
LF33CPT
LF33ABPT
LF35CPT
LF35ABPT
LF40CPT
LF40ABPT
LF45CPT
LF45ABPT
LF47CPT
LF47ABPT
LF50CPT
LF50ABPT
LF52CPT
LF52ABPT
LF55CPT
LF55ABPT
LF60CPT
LF60ABPT
LF80CPT
LF80ABPT
LF85CPT
LF85ABPT
LF90CPT
LF90ABPT
LF120CPT
LF120ABPT
1.25 V
1.25 V
1.5 V
1.5 V
1.8 V
1.8 V
2.5 V
2.5 V
2.7 V
2.7 V
3V
3V
3.3 V
3.3 V
3.5 V
3.5 V
4V
4V
4.5 V
4.5 V
4.75 V
4.75 V
5V
5V
5.2 V
5.2 V
5.5 V
5.5 V
6V
6V
8V
8V
8.5 V
8.5 V
9V
9V
12 V
12 V
(*) Available on request.
(#) Available in Tape & Reel with the suffix "-TR".
3/34
LF00 SERIES
TEST CIRCUITS
ELECTRICAL CHARACTERISTICS FOR LF12AB (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
Parameter
Test Conditions
VO
Output Voltage
IO = 50 mA, VI = 3.3 V
IO = 50 mA, VI = 3.3 V, Ta = -25 to 85°C
VI
Operating Input Voltage
IO = 500 mA
IO
Output Current Limit
Min.
Typ.
Max.
Unit
1.238
1.25
1.263
V
1.225
1.275
2.5
16
V
2
10
mV
1
A
∆VO
Line Regulation
VI = 2.5 to 16 V,
IO = 5 mA
∆VO
Load Regulation
VI = 2.8 V
IO = 5 to 500 mA
2
10
mV
Quiescent Current
VI = 2.5 to 16V, IO = 0mA
ON MODE
VI = 2.6 to 16V, IO = 500mA
0.5
1
mA
VI = 6 V
OFF MODE
50
100
Supply Voltage Rejection
IO = 5 mA
VI = 3.5 ± 1 V
f = 120 Hz
f = 1 KHz
f = 10 KHz
eN
Vd
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
82
77
65
50
1.25
VIL
Control Input Logic Low
Ta = -40 to 125°C
VIH
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
Id
SVR
II
CO
4/34
12
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
dB
µV
V
0.8
2
IO = 0 to 500 mA
2
µA
V
V
10
µA
10
µF
LF00 SERIES
ELECTRICAL CHARACTERISTICS FOR LF12C (refer to the test circuits, Tj = 25°C, CI = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
VO
Parameter
Test Conditions
Output Voltage
IO = 50 mA, VI = 3.3 V
VI
Operating Input Voltage
IO = 50 mA, VI = 3.3 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
Min.
Typ.
Max.
Unit
1.225
1.25
1.275
V
1.2
1.3
2.5
16
V
1
A
∆VO
Line Regulation
VI = 2.5 to 16 V,
IO = 5 mA
2
10
mV
∆VO
Load Regulation
VI = 2.8 V
IO = 5 to 500 mA
2
10
mV
Quiescent Current
VI = 2.5 to 16V, IO = 0mA
ON MODE
0.5
1
mA
VI = 6 V
OFF MODE
50
100
Supply Voltage Rejection
IO = 5 mA
VI = 3.5 ± 1 V
f = 120 Hz
f = 1 KHz
f = 10 KHz
eN
Vd
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
82
77
65
50
1.25
VIL
Control Input Logic Low
Ta = -40 to 125°C
VIH
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
Id
VI = 2.6 to 16V, IO = 500mA
SVR
II
CO
12
µA
dB
µV
V
0.8
V
2
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
IO = 0 to 500 mA
2
V
10
µA
10
µF
ELECTRICAL CHARACTERISTICS FOR LF15AB (refer to the test circuits, Tj = 25°C, CI = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
Parameter
Test Conditions
VO
Output Voltage
IO = 50 mA, VI = 3.5 V
IO = 50 mA, VI = 3.5 V, Ta = -25 to 85°C
VI
Operating Input Voltage
IO = 500 mA
IO
Output Current Limit
Min.
Typ.
Max.
Unit
1.485
1.5
1.515
V
1.470
1.530
2.5
16
V
2
10
mV
1
∆VO
Line Regulation
VI = 2.5 to 16 V,
IO = 5 mA
∆VO
Load Regulation
VI = 2.8 V,
IO = 5 to 500 mA
Quiescent Current
VI = 2.5 to 16V, IO = 0mA
A
2
10
mV
ON MODE
0.5
1
mA
VI = 6 V
OFF MODE
50
100
Supply Voltage Rejection
IO = 5 mA
VI = 3.5 ± 1 V
f = 120 Hz
f = 1 KHz
f = 10 KHz
eN
Vd
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
82
77
65
50
1
VIL
Control Input Logic Low
Ta = -40 to 125°C
VIH
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
Id
VI = 2.8 to 16V, IO = 500mA
SVR
II
CO
12
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
dB
µV
V
0.8
2
IO = 0 to 500 mA
2
µA
V
V
10
µA
10
µF
5/34
LF00 SERIES
ELECTRICAL CHARACTERISTICS FOR LF15C (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
VO
Parameter
Test Conditions
Min.
Typ.
1.5
Output Voltage
IO = 50 mA, VI = 3.5 V
1.47
1.44
VI
Operating Input Voltage
IO = 50 mA, VI = 3.5 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
Max.
Unit
1.53
V
1.56
2.5
16
V
1
A
∆VO
Line Regulation
VI = 2.5 to 16 V,
IO = 5 mA
2
10
mV
∆VO
Load Regulation
VI = 2.8 V,
IO = 5 to 500 mA
2
10
mV
Quiescent Current
VI = 2.5 to 16V, IO = 0mA
ON MODE
VI = 2.8 to 16V, IO = 500mA
0.5
1
mA
VI = 6 V
OFF MODE
50
100
Supply Voltage Rejection
IO = 5 mA
VI = 3.5 ± 1 V
f = 120 Hz
f = 1 KHz
f = 10 KHz
eN
Vd
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
82
77
65
50
1
VIL
Control Input Logic Low
Ta = -40 to 125°C
VIH
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
Id
SVR
II
CO
12
µA
dB
µV
V
0.8
V
2
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
IO = 0 to 500 mA
2
V
10
µA
10
µF
ELECTRICAL CHARACTERISTICS FOR LF18AB (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
Parameter
Test Conditions
Min.
Typ.
1.8
Max.
Unit
1.818
V
Output Voltage
IO = 50 mA, VI = 3.3 V
1.782
1.764
1.836
VI
Operating Input Voltage
IO = 50 mA, VI = 3.3 V, Ta = -25 to 85°C
IO = 500 mA
3
16
V
IO
Output Current Limit
2
12
mV
VO
1
A
∆VO
Line Regulation
VI = 2.8 to 16 V,
IO = 5 mA
∆VO
Load Regulation
VI = 3.3 V,
IO = 5 to 500 mA
2
10
mV
Quiescent Current
VI = 2.5 to 16V, IO = 0mA
ON MODE
VI = 3.1 to 16V, IO = 500mA
0.5
1
mA
VI = 6 V
OFF MODE
50
100
Supply Voltage Rejection
IO = 5 mA
VI = 3.5 ± 1 V
f = 120 Hz
f = 1 KHz
f = 10 KHz
eN
Vd
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
82
77
60
50
0.7
VIL
Control Input Logic Low
Ta = -40 to 125°C
VIH
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
Id
SVR
II
CO
6/34
12
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
dB
µV
V
0.8
2
IO = 0 to 500 mA
2
µA
V
V
10
µA
10
µF
LF00 SERIES
ELECTRICAL CHARACTERISTICS FOR LF18C (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
VO
Parameter
Test Conditions
Min.
Typ.
1.8
Output Voltage
IO = 50 mA, VI = 3.5 V
1.764
1.728
VI
Operating Input Voltage
IO = 50 mA, VI = 3.5 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
Max.
Unit
1.836
V
1.872
3
16
V
1
A
∆VO
Line Regulation
VI = 2.8 to 16 V,
IO = 5 mA
2
12
mV
∆VO
Load Regulation
VI = 3.3 V,
IO = 5 to 500 mA
2
10
mV
Quiescent Current
VI = 2.5 to 16V, IO = 0mA
ON MODE
VI = 3.1 to 16V, IO = 500mA
0.5
1
mA
VI = 6 V
OFF MODE
50
100
Supply Voltage Rejection
IO = 5 mA
VI = 3.5 ± 1 V
f = 120 Hz
f = 1 KHz
f = 10 KHz
eN
Vd
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
82
77
60
50
0.7
VIL
Control Input Logic Low
Ta = -40 to 125°C
VIH
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
Id
SVR
II
CO
12
µA
dB
µV
V
0.8
V
2
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
IO = 0 to 500 mA
2
V
10
µA
10
µF
ELECTRICAL CHARACTERISTICS FOR LF25AB (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
Parameter
Test Conditions
VO
Output Voltage
IO = 50 mA, VI = 4.5 V
IO = 50 mA, VI = 4.5 V, Ta = -25 to 85°C
VI
Operating Input Voltage
IO = 500 mA
IO
Output Current Limit
Min.
Typ.
Max.
Unit
2.475
2.5
2.525
V
2.450
2.550
16
V
2
12
mV
1
A
∆VO
Line Regulation
VI = 3.5 to 16 V,
IO = 5 mA
∆VO
Load Regulation
VI = 3.8 V,
IO = 5 to 500 mA
2
12
mV
Quiescent Current
VI = 3.5 to 16V, IO = 0mA
ON MODE
VI = 3.8 to 16V, IO = 500mA
0.5
1
mA
VI = 6 V
OFF MODE
50
100
Supply Voltage Rejection
IO = 5 mA
VI = 4.5 ± 1 V
f = 120 Hz
f = 1 KHz
f = 10 KHz
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
82
77
65
50
0.2
0.35
IO = 500 mA
0.4
0.7
Id
SVR
eN
Vd
VIL
Control Input Logic Low
Ta = -40 to 125°C
VIH
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
II
CO
12
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
dB
0.8
2
IO = 0 to 500 mA
2
µA
µV
V
V
V
10
µA
10
µF
7/34
LF00 SERIES
ELECTRICAL CHARACTERISTICS FOR LF25C (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
VO
Parameter
Test Conditions
Min.
Typ.
Max.
Unit
2.5
2.55
V
Output Voltage
IO = 50 mA, VI = 4.5 V
2.45
2.4
VI
Operating Input Voltage
IO = 50 mA, VI = 4.5 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
2.6
16
A
∆VO
Line Regulation
VI = 3.5 to 16 V,
IO = 5 mA
∆VO
Load Regulation
VI = 3.8 V,
IO = 5 to 500 mA
Quiescent Current
VI = 3.5 to 16V, IO = 0mA
ON MODE
VI = 3.8 to 16V, IO = 500mA
VI = 6 V
OFF MODE
50
100
Supply Voltage Rejection
IO = 5 mA
VI = 4.5 ± 1 V
f = 120 Hz
f = 1 KHz
f = 10 KHz
eN
Vd
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
82
77
65
50
0.2
IO = 500 mA
0.4
VIL
Control Input Logic Low
VIH
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
Id
SVR
II
CO
V
1
2
12
mV
2
12
mV
0.5
1
mA
12
Ta = -40 to 125°C
µA
dB
0.35
µV
V
0.7
0.8
V
2
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
IO = 0 to 500 mA
2
V
10
µA
10
µF
ELECTRICAL CHARACTERISTICS FOR LF27AB (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
Parameter
Test Conditions
Min.
Typ.
2.7
Output Voltage
IO = 50 mA, VI = 4.7 V
2.673
2.646
VI
Operating Input Voltage
IO = 50 mA, VI = 4.7 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
VO
Max.
Unit
2.727
V
2.754
16
1
V
A
∆VO
Line Regulation
VI = 3.7 to 16 V,
IO = 5 mA
2
13
mV
∆VO
Load Regulation
VI = 4 V,
IO = 5 to 500 mA
2
13
mV
1
mA
Id
Quiescent Current
VI = 3.7 to 16V IO = 0mA
VI = 4 to 16V
SVR
eN
Vd
OFF MODE
50
IO = 5 mA
VI = 4.7 ± 1 V
f = 120 Hz
f = 1 KHz
f = 10 KHz
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
82
77
65
50
0.2
0.35
IO = 500 mA
0.4
0.7
Control Input Logic Low
Ta = -40 to 125°C
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
8/34
12
VI = 6 V
VIL
II
0.5
Supply Voltage Rejection
VIH
CO
ON MODE
IO = 500mA
IO = 0 to 500 mA
2
µA
dB
0.8
2
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
100
µV
V
V
V
10
µA
10
µF
LF00 SERIES
ELECTRICAL CHARACTERISTICS FOR LF27C (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
VO
Parameter
Test Conditions
Min.
Typ.
2.7
Output Voltage
IO = 50 mA, VI = 4.7 V
2.646
2.592
VI
Operating Input Voltage
IO = 50 mA, VI = 4.7 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
Max.
Unit
2.754
V
2.808
16
A
∆VO
Line Regulation
VI = 3.7 to 16 V
IO = 5 mA
∆VO
Load Regulation
VI = 4 V,
IO = 5 to 500 mA
Quiescent Current
VI = 3.7 to 16V IO = 0mA
ON MODE
VI = 4 to 16V IO = 500mA
VI = 6 V
OFF MODE
50
100
Supply Voltage Rejection
IO = 5 mA
VI = 4.7 ± 1 V
f = 120 Hz
f = 1 KHz
f = 10 KHz
eN
Vd
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
82
77
65
50
0.2
IO = 500 mA
0.4
VIL
Control Input Logic Low
VIH
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
Id
SVR
II
CO
V
1
2
13
mV
2
13
mV
0.5
1
mA
12
Ta = -40 to 125°C
µA
dB
0.35
µV
V
0.7
0.8
V
2
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
IO = 0 to 500 mA
2
V
10
µA
10
µF
ELECTRICAL CHARACTERISTICS FOR LF30AB (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
Parameter
Test Conditions
Min.
Typ.
Max.
Unit
3
3.03
V
Output Voltage
IO = 50 mA, VI = 5 V
2.970
2.94
VI
Operating Input Voltage
IO = 50 mA, VI = 5 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
VO
3.06
16
1
V
A
∆VO
Line Regulation
VI = 4 to 16 V,
IO = 5 mA
3
15
mV
∆VO
Load Regulation
VI = 4.3 V,
IO = 5 to 500 mA
3
15
mV
1
mA
Id
Quiescent Current
VI = 4 to 16V,
IO = 0mA
ON MODE
0.5
VI = 4.3 to 16V IO = 500mA
OFF MODE
VI = 6 V
SVR
eN
Vd
Supply Voltage Rejection
IO = 5 mA
VI = 5 ± 1 V
Output Noise Voltage
Dropout Voltage
100
B = 10 Hz to 100 KHz
IO = 200 mA
81
76
65
50
0.2
0.35
IO = 500 mA
0.4
0.7
VIL
Control Input Logic Low
Ta = -40 to 125°C
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
II
50
f = 120 Hz
f = 1 KHz
f = 10 KHz
VIH
CO
12
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
dB
0.8
2
IO = 0 to 500 mA
2
µA
µV
V
V
V
10
µA
10
µF
9/34
LF00 SERIES
ELECTRICAL CHARACTERISTICS FOR LF30C (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
VO
Parameter
Test Conditions
Min.
Typ.
Max.
Unit
3
3.06
V
Output Voltage
IO = 50 mA, VI = 5 V
2.94
2.88
VI
Operating Input Voltage
IO = 50 mA, VI = 5 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
3.12
16
V
1
A
∆VO
Line Regulation
VI = 4 to 16 V,
IO = 5 mA
3
15
mV
∆VO
Load Regulation
VI = 4.3 V,
IO = 5 to 500 mA
3
15
mV
Quiescent Current
VI = 4 to 16V,
ON MODE
0.5
1
mA
VI = 6 V
OFF MODE
50
100
Supply Voltage Rejection
IO = 5 mA
VI = 5 ± 1 V
f = 120 Hz
f = 1 KHz
f = 10 KHz
eN
Vd
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
81
76
65
50
0.2
IO = 500 mA
0.4
VIL
Control Input Logic Low
VIH
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
Id
IO = 0mA
VI = 4.3 to 16V IO = 500mA
SVR
II
CO
12
Ta = -40 to 125°C
µA
dB
0.35
µV
V
0.7
0.8
V
2
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
IO = 0 to 500 mA
2
V
10
µA
10
µF
ELECTRICAL CHARACTERISTICS FOR LF33AB (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
Parameter
Test Conditions
Min.
Typ.
3.3
Output Voltage
IO = 50 mA, VI = 5.3 V
3.267
3.234
VI
Operating Input Voltage
IO = 50 mA, VI = 5.3 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
VO
Max.
Unit
3.333
V
3.366
16
1
V
A
∆VO
Line Regulation
VI = 4.3 to 16 V,
IO = 5 mA
3
16
mV
∆VO
Load Regulation
VI = 4.6 V,
IO = 5 to 500 mA
3
16
mV
1
mA
Id
Quiescent Current
VI = 4.3 to 16V, IO = 0mA
ON MODE
0.5
VI = 4.6 to 16V, IO = 500mA
VI = 6 V
OFF MODE
12
50
Supply Voltage Rejection
IO = 5 mA
VI = 5.3 ± 1 V
eN
Vd
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
80
75
65
50
0.2
IO = 500 mA
0.4
VIL
Control Input Logic Low
VIH
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
SVR
II
CO
10/34
f = 120 Hz
f = 1 KHz
f = 10 KHz
Ta = -40 to 125°C
2
IO = 0 to 500 mA
2
µA
dB
0.35
µV
V
0.7
0.8
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
100
V
V
10
µA
10
µF
LF00 SERIES
ELECTRICAL CHARACTERISTICS FOR LF33C (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
VO
Parameter
Test Conditions
Min.
Typ.
3.3
Output Voltage
IO = 50 mA, VI = 5.3 V
3.234
3.168
VI
Operating Input Voltage
IO = 50 mA, VI = 5.3 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
Max.
Unit
3.366
V
3.432
16
A
∆VO
Line Regulation
VI = 4.3 to 16 V,
IO = 5 mA
∆VO
Load Regulation
VI = 4.6 V,
IO = 5 to 500 mA
Quiescent Current
VI = 4.3 to 16V, IO = 0mA
ON MODE
VI = 4.6 to 16V, IO = 500mA
VI = 6 V
OFF MODE
50
100
Supply Voltage Rejection
IO = 5 mA
VI = 5.3 ± 1 V
f = 120 Hz
f = 1 KHz
f = 10 KHz
eN
Vd
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
80
75
65
50
0.2
IO = 500 mA
0.4
VIL
Control Input Logic Low
VIH
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
Id
SVR
II
CO
V
1
3
16
mV
3
16
mV
0.5
1
mA
12
Ta = -40 to 125°C
µA
dB
0.35
µV
V
0.7
0.8
V
2
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
IO = 0 to 500 mA
2
V
10
µA
10
µF
ELECTRICAL CHARACTERISTICS FOR LF35AB (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
Parameter
Test Conditions
Min.
Typ.
3.5
Output Voltage
IO = 50 mA, VI = 5.5 V
3.465
3.430
VI
Operating Input Voltage
IO = 50 mA, VI = 5.5 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
VO
Max.
Unit
3.535
V
3.570
16
1
V
A
∆VO
Line Regulation
VI = 4.5 to 16 V,
IO = 5 mA
3
17
mV
∆VO
Load Regulation
VI = 4.8 V,
IO = 5 to 500 mA
3
17
mV
1
mA
Id
Quiescent Current
VI = 4.5 to 16V, IO = 0mA
ON MODE
0.5
VI = 4.8 to 16V, IO = 500mA
OFF MODE
VI = 6 V
SVR
eN
Vd
Supply Voltage Rejection
IO = 5 mA
VI = 5.5 ± 1 V
Output Noise Voltage
Dropout Voltage
100
B = 10 Hz to 100 KHz
IO = 200 mA
79
74
60
50
0.2
0.35
IO = 500 mA
0.4
0.7
VIL
Control Input Logic Low
Ta = -40 to 125°C
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
II
50
f = 120 Hz
f = 1 KHz
f = 10 KHz
VIH
CO
12
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
dB
0.8
2
IO = 0 to 500 mA
2
µA
µV
V
V
V
10
µA
10
µF
11/34
LF00 SERIES
ELECTRICAL CHARACTERISTICS FOR LF35C (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
VO
Parameter
Test Conditions
Min.
Typ.
3.5
Output Voltage
IO = 50 mA, VI = 5.5 V
3.43
3.36
VI
Operating Input Voltage
IO = 50 mA, VI = 5.5 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
Max.
Unit
3.57
V
3.64
16
A
∆VO
Line Regulation
VI = 4.5 to 16 V,
IO = 5 mA
∆VO
Load Regulation
VI = 4.8 V,
IO = 5 to 500 mA
Quiescent Current
VI = 4.5 to 16V, IO = 0mA
ON MODE
VI = 4.8 to 16V, IO = 500mA
VI = 6 V
OFF MODE
50
100
Supply Voltage Rejection
IO = 5 mA
VI = 5.5 ± 1 V
f = 120 Hz
f = 1 KHz
f = 10 KHz
eN
Vd
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
79
74
60
50
0.2
IO = 500 mA
0.4
VIL
Control Input Logic Low
VIH
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
Id
SVR
II
CO
V
1
3
17
mV
3
17
mV
0.5
1
mA
12
Ta = -40 to 125°C
µA
dB
0.35
µV
V
0.7
0.8
V
2
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
IO = 0 to 500 mA
2
V
10
µA
10
µF
ELECTRICAL CHARACTERISTICS FOR LF40AB (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
Parameter
Test Conditions
Min.
Typ.
Max.
Unit
4
4.04
V
Output Voltage
IO = 50 mA, VI = 6 V
3.96
3.92
VI
Operating Input Voltage
IO = 50 mA, VI = 6 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
VO
4.08
16
1
V
A
∆VO
Line Regulation
VI = 5 to 16 V,
IO = 5 mA
4
20
mV
∆VO
Load Regulation
VI = 5.3 V,
IO = 5 to 500 mA
4
20
mV
1
mA
Id
Quiescent Current
VI = 5 to 16V,
IO = 0mA
ON MODE
0.5
VI = 5.3 to 16V, IO = 500mA
OFF MODE
VI = 6 V
SVR
eN
Vd
Supply Voltage Rejection
IO = 5 mA
VI = 6 ± 1 V
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
0.35
IO = 500 mA
0.4
0.7
Control Input Logic Low
Ta = -40 to 125°C
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
12/34
100
78
73
60
50
0.2
VIL
II
50
f = 120 Hz
f = 1 KHz
f = 10 KHz
VIH
CO
12
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
dB
0.8
2
IO = 0 to 500 mA
2
µA
µV
V
V
V
10
µA
10
µF
LF00 SERIES
ELECTRICAL CHARACTERISTICS FOR LF40C (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
VO
Parameter
Test Conditions
Min.
Typ.
Max.
Unit
4
4.08
V
Output Voltage
IO = 50 mA, VI = 6 V
3.92
3.84
VI
Operating Input Voltage
IO = 50 mA, VI = 6 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
4.16
16
V
1
∆VO
Line Regulation
VI = 5 to 16 V,
∆VO
Load Regulation
VI = 5.3 V,
Quiescent Current
VI = 5 to 16V,
IO = 5 mA
4
20
mV
4
20
mV
ON MODE
0.5
1
mA
VI = 6 V
OFF MODE
50
100
Supply Voltage Rejection
IO = 5 mA
VI = 6 ± 1 V
f = 120 Hz
f = 1 KHz
f = 10 KHz
eN
Vd
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
78
73
60
50
0.2
IO = 500 mA
0.4
VIL
Control Input Logic Low
VIH
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
Id
IO = 5 to 500 mA
A
IO = 0mA
VI = 5.3 to 16V, IO = 500mA
SVR
II
CO
12
Ta = -40 to 125°C
µA
dB
0.35
µV
V
0.7
0.8
V
2
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
IO = 0 to 500 mA
2
V
10
µA
10
µF
ELECTRICAL CHARACTERISTICS FOR LF45AB (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
Parameter
Test Conditions
Min.
Typ.
Max.
Unit
4.5
4.545
V
Output Voltage
IO = 50 mA, VI = 6.5 V
4.455
4.41
VI
Operating Input Voltage
IO = 50 mA, VI = 6.5 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
VO
4.59
16
1
V
A
∆VO
Line Regulation
VI = 5.5 to 16 V,
IO = 5 mA
4
22
mV
∆VO
Load Regulation
VI = 5.8 V,
IO = 5 to 500 mA
4
22
mV
1
mA
Id
Quiescent Current
VI = 5.5 to 16V, IO = 0mA
ON MODE
0.5
VI = 5.8 to 16V, IO = 500mA
OFF MODE
VI = 6 V
SVR
eN
Vd
Supply Voltage Rejection
IO = 5 mA
VI = 6.5 ± 1 V
Output Noise Voltage
Dropout Voltage
100
B = 10 Hz to 100 KHz
IO = 200 mA
77
72
60
50
0.2
0.35
IO = 500 mA
0.4
0.7
VIL
Control Input Logic Low
Ta = -40 to 125°C
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
II
50
f = 120 Hz
f = 1 KHz
f = 10 KHz
VIH
CO
12
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
dB
0.8
2
IO = 0 to 500 mA
2
µA
µV
V
V
V
10
µA
10
µF
13/34
LF00 SERIES
ELECTRICAL CHARACTERISTICS FOR LF45C (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
VO
Parameter
Test Conditions
Min.
Typ.
4.5
Output Voltage
IO = 50 mA, VI = 6.5 V
4.41
4.32
VI
Operating Input Voltage
IO = 50 mA, VI = 6.5 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
Max.
Unit
4.59
V
4.68
16
A
∆VO
Line Regulation
VI = 5.5 to 16 V,
IO = 5 mA
∆VO
Load Regulation
VI = 5.8 V,
IO = 5 to 500 mA
Quiescent Current
VI = 5.5 to 16V, IO = 0mA
ON MODE
VI = 5.8 to 16V, IO = 500mA
VI = 6 V
OFF MODE
50
100
Supply Voltage Rejection
IO = 5 mA
VI = 6.5 ± 1 V
f = 120 Hz
f = 1 KHz
f = 10 KHz
eN
Vd
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
77
72
60
50
0.2
IO = 500 mA
0.4
VIL
Control Input Logic Low
VIH
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
Id
SVR
II
CO
V
1
4
22
mV
4
22
mV
0.5
1
mA
12
Ta = -40 to 125°C
µA
dB
0.35
µV
V
0.7
0.8
V
2
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
IO = 0 to 500 mA
2
V
10
µA
10
µF
ELECTRICAL CHARACTERISTICS FOR LF47AB (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
Parameter
Test Conditions
Min.
Typ.
4.7
Output Voltage
IO = 50 mA, VI = 6.7 V
4.653
4.606
VI
Operating Input Voltage
IO = 50 mA, VI = 6.7 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
VO
Max.
Unit
4.747
V
4.794
16
1
V
A
∆VO
Line Regulation
VI = 5.7 to 16 V,
IO = 5 mA
4
23
mV
∆VO
Load Regulation
VI = 6 V,
IO = 5 to 500 mA
4
23
mV
1
mA
Id
Quiescent Current
VI = 5.7 to 16V, IO = 0mA
VI = 6 to 16V,
SVR
eN
Vd
OFF MODE
50
IO = 5 mA
VI = 6.7 ± 1 V
f = 120 Hz
f = 1 KHz
f = 10 KHz
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
77
72
60
50
0.2
0.35
IO = 500 mA
0.4
0.7
Control Input Logic Low
Ta = -40 to 125°C
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
14/34
12
VI = 6 V
VIL
II
0.5
Supply Voltage Rejection
VIH
CO
ON MODE
IO = 500mA
IO = 0 to 500 mA
2
µA
dB
0.8
2
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
100
µV
V
V
V
10
µA
10
µF
LF00 SERIES
ELECTRICAL CHARACTERISTICS FOR LF47C (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
VO
Parameter
Test Conditions
Min.
Typ.
4.7
Output Voltage
IO = 50 mA, VI = 6.7 V
4.606
4.512
VI
Operating Input Voltage
IO = 50 mA, VI = 6.7 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
Max.
Unit
4.794
V
4.888
16
A
∆VO
Line Regulation
VI = 5.7 to 16 V,
IO = 5 mA
∆VO
Load Regulation
VI = 6 V,
IO = 5 to 500 mA
Quiescent Current
VI = 5.7 to 16V, IO = 0mA
ON MODE
VI = 6 to 16V, IO = 500mA
VI = 6 V
OFF MODE
50
100
Supply Voltage Rejection
IO = 5 mA
VI = 6.7 ± 1 V
f = 120 Hz
f = 1 KHz
f = 10 KHz
eN
Vd
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
77
72
60
50
0.2
IO = 500 mA
0.4
VIL
Control Input Logic Low
VIH
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
Id
SVR
II
CO
V
1
4
23
mV
4
23
mV
0.5
1
mA
12
Ta = -40 to 125°C
µA
dB
0.35
µV
V
0.7
0.8
V
2
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
IO = 0 to 500 mA
2
V
10
µA
10
µF
ELECTRICAL CHARACTERISTICS FOR LF50AB (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
Parameter
Test Conditions
Min.
Typ.
Max.
Unit
5
5.05
V
Output Voltage
IO = 50 mA, VI = 7 V
4.95
4.9
VI
Operating Input Voltage
IO = 50 mA, VI = 7 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
VO
5.1
16
1
V
A
∆VO
Line Regulation
VI = 6 to 16 V,
IO = 5 mA
5
25
mV
∆VO
Load Regulation
VI = 6.3 V,
IO = 5 to 500 mA
5
25
mV
1
mA
Id
Quiescent Current
VI = 6 to 16V,
IO = 0mA
ON MODE
0.5
VI = 6.3 to 16V, IO = 500mA
OFF MODE
VI = 6 V
SVR
eN
Vd
Supply Voltage Rejection
IO = 5 mA
VI = 7 ± 1 V
Output Noise Voltage
Dropout Voltage
100
B = 10 Hz to 100 KHz
IO = 200 mA
76
71
60
50
0.2
0.35
IO = 500 mA
0.4
0.7
VIL
Control Input Logic Low
Ta = -40 to 125°C
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
II
50
f = 120 Hz
f = 1 KHz
f = 10 KHz
VIH
CO
12
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
dB
0.8
2
IO = 0 to 500 mA
2
µA
µV
V
V
V
10
µA
10
µF
15/34
LF00 SERIES
ELECTRICAL CHARACTERISTICS FOR LF50C (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
VO
Parameter
Test Conditions
Min.
Typ.
Max.
Unit
5
5.1
V
Output Voltage
IO = 50 mA, VI = 7 V
4.9
4.8
VI
Operating Input Voltage
IO = 50 mA, VI = 7 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
5.2
16
V
1
∆VO
Line Regulation
VI = 6 to 16 V,
∆VO
Load Regulation
VI = 6.3 V,
Quiescent Current
VI = 6 to 16V,
IO = 5 mA
5
25
mV
5
25
mV
ON MODE
0.5
1
mA
VI = 6 V
OFF MODE
50
100
Supply Voltage Rejection
IO = 5 mA
VI = 7 ± 1 V
f = 120 Hz
f = 1 KHz
f = 10 KHz
eN
Vd
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
76
71
60
50
0.2
IO = 500 mA
0.4
VIL
Control Input Logic Low
VIH
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
Id
IO = 5 to 500 mA
A
IO = 0mA
VI = 6.3 to 16V, IO = 500mA
SVR
II
CO
12
Ta = -40 to 125°C
µA
dB
0.35
µV
V
0.7
0.8
V
2
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
IO = 0 to 500 mA
2
V
10
µA
10
µF
ELECTRICAL CHARACTERISTICS FOR LF52AB (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
Parameter
Test Conditions
Min.
Typ.
5.2
Output Voltage
IO = 50 mA, VI = 7.2 V
5.148
5.096
VI
Operating Input Voltage
IO = 50 mA, VI = 7.2 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
VO
Max.
Unit
5.252
V
5.304
16
1
V
A
∆VO
Line Regulation
VI = 6.2 to 16 V,
IO = 5 mA
5
26
mV
∆VO
Load Regulation
VI = 6.5 V,
IO = 5 to 500 mA
5
26
mV
1
mA
Id
Quiescent Current
VI = 6.2 to 16V, IO = 0mA
ON MODE
0.5
VI = 6.5 to 16V, IO = 500mA
OFF MODE
VI = 6 V
SVR
eN
Vd
Supply Voltage Rejection
IO = 5 mA
VI = 7.2 ± 1 V
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
0.35
IO = 500 mA
0.4
0.7
Control Input Logic Low
Ta = -40 to 125°C
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
16/34
100
76
71
60
50
0.2
VIL
II
50
f = 120 Hz
f = 1 KHz
f = 10 KHz
VIH
CO
12
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
dB
0.8
2
IO = 0 to 500 mA
2
µA
µV
V
V
V
10
µA
10
µF
LF00 SERIES
ELECTRICAL CHARACTERISTICS FOR LF52C (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
VO
Parameter
Test Conditions
Min.
Typ.
5.2
Output Voltage
IO = 50 mA, VI = 7.2 V
5.096
4.992
VI
Operating Input Voltage
IO = 50 mA, VI = 7.2 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
Max.
Unit
5.304
V
5.408
16
A
∆VO
Line Regulation
VI = 6.2 to 16 V,
IO = 5 mA
∆VO
Load Regulation
VI = 6.5 V,
IO = 5 to 500 mA
Quiescent Current
VI = 6.2 to 16V, IO = 0mA
ON MODE
VI = 6.5 to 16V, IO = 500mA
VI = 6 V
OFF MODE
50
100
Supply Voltage Rejection
IO = 5 mA
VI = 7.2 ± 1 V
f = 120 Hz
f = 1 KHz
f = 10 KHz
eN
Vd
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
76
71
60
50
0.2
IO = 500 mA
0.4
VIL
Control Input Logic Low
VIH
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
Id
SVR
II
CO
V
1
5
26
mV
5
26
mV
0.5
1
mA
12
Ta = -40 to 125°C
µA
dB
0.35
µV
V
0.7
0.8
V
2
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
IO = 0 to 500 mA
2
V
10
µA
10
µF
ELECTRICAL CHARACTERISTICS FOR LF55AB (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
Parameter
Test Conditions
Min.
Typ.
Max.
Unit
5.5
5.555
V
Output Voltage
IO = 50 mA, VI = 7.5 V
5.445
5.39
VI
Operating Input Voltage
IO = 50 mA, VI = 7.5 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
VO
5.61
16
1
V
A
∆VO
Line Regulation
VI = 6.5 to 16 V,
IO = 5 mA
5
27
mV
∆VO
Load Regulation
VI = 6.8 V,
IO = 5 to 500 mA
5
27
mV
1
mA
Id
Quiescent Current
VI = 6.5 to 16V, IO = 0mA
ON MODE
0.5
VI = 6.8 to 16V, IO = 500mA
OFF MODE
VI = 6 V
SVR
eN
Vd
Supply Voltage Rejection
IO = 5 mA
VI = 7.5 ± 1 V
Output Noise Voltage
Dropout Voltage
100
B = 10 Hz to 100 KHz
IO = 200 mA
76
71
60
50
0.2
0.35
IO = 500 mA
0.4
0.7
VIL
Control Input Logic Low
Ta = -40 to 125°C
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
II
50
f = 120 Hz
f = 1 KHz
f = 10 KHz
VIH
CO
12
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
dB
0.8
2
IO = 0 to 500 mA
2
µA
µV
V
V
V
10
µA
10
µF
17/34
LF00 SERIES
ELECTRICAL CHARACTERISTICS FOR LF55C (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
VO
Parameter
Test Conditions
Min.
Typ.
5.5
Output Voltage
IO = 50 mA, VI = 7.5 V
5.39
5.28
VI
Operating Input Voltage
IO = 50 mA, VI = 7.5 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
Max.
Unit
5.61
V
5.72
16
A
∆VO
Line Regulation
VI = 6.5 to 16 V,
IO = 5 mA
∆VO
Load Regulation
VI = 6.8 V,
IO = 5 to 500 mA
Quiescent Current
VI = 6.5 to 16V, IO = 0mA
ON MODE
VI = 6.8 to 16V, IO = 500mA
VI = 6 V
OFF MODE
50
100
Supply Voltage Rejection
IO = 5 mA
VI = 7.5 ± 1 V
f = 120 Hz
f = 1 KHz
f = 10 KHz
eN
Vd
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
76
71
60
50
0.2
IO = 500 mA
0.4
VIL
Control Input Logic Low
VIH
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 6 V,
Id
SVR
II
CO
V
1
5
27
mV
5
27
mV
0.5
1
mA
12
Ta = -40 to 125°C
µA
dB
0.35
µV
V
0.7
0.8
V
2
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
IO = 0 to 500 mA
2
V
10
µA
10
µF
ELECTRICAL CHARACTERISTICS FOR LF60AB (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
Parameter
Test Conditions
Min.
Typ.
Max.
Unit
6
6.06
V
Output Voltage
IO = 50 mA, VI = 8 V
5.94
5.88
VI
Operating Input Voltage
IO = 50 mA, VI = 8 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
VO
6.12
16
1
V
A
∆VO
Line Regulation
VI = 7 to 16 V,
IO = 5 mA
6
30
mV
∆VO
Load Regulation
VI = 7.3 V,
IO = 5 to 500 mA
6
30
mV
0.7
1.5
mA
Id
Quiescent Current
VI = 7 to 16V,
IO = 0mA
ON MODE
VI = 7.3 to 16V, IO = 500mA
OFF MODE
VI = 9 V
SVR
eN
Vd
Supply Voltage Rejection
IO = 5 mA
VI = 8 ± 1 V
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
0.35
IO = 500 mA
0.4
0.7
Control Input Logic Low
Ta = -40 to 125°C
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 9 V,
18/34
140
75
70
60
50
0.2
VIL
II
70
f = 120 Hz
f = 1 KHz
f = 10 KHz
VIH
CO
12
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
dB
0.8
2
IO = 0 to 500 mA
2
µA
µV
V
V
V
10
µA
10
µF
LF00 SERIES
ELECTRICAL CHARACTERISTICS FOR LF60C (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
VO
Parameter
Test Conditions
Min.
Typ.
Max.
Unit
6
6.12
V
Output Voltage
IO = 50 mA, VI = 8 V
5.88
5.76
VI
Operating Input Voltage
IO = 50 mA, VI = 8 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
6.24
16
V
1
∆VO
Line Regulation
VI = 7 to 16 V,
∆VO
Load Regulation
VI = 7.3 V,
Quiescent Current
VI = 7 to 16V,
IO = 5 mA
6
30
mV
6
30
mV
ON MODE
0.7
1.5
mA
VI = 9 V
OFF MODE
70
140
Supply Voltage Rejection
IO = 5 mA
VI = 8 ± 1 V
f = 120 Hz
f = 1 KHz
f = 10 KHz
eN
Vd
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
75
70
60
50
0.2
IO = 500 mA
0.4
VIL
Control Input Logic Low
VIH
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 9 V,
Id
IO = 5 to 500 mA
A
IO = 0mA
VI = 7.3 to 16V, IO = 500mA
SVR
II
CO
12
Ta = -40 to 125°C
µA
dB
0.35
µV
V
0.7
0.8
V
2
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
IO = 0 to 500 mA
2
V
10
µA
10
µF
ELECTRICAL CHARACTERISTICS FOR LF80AB (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
Parameter
Test Conditions
Min.
Typ.
Max.
Unit
8
8.08
V
Output Voltage
IO = 50 mA, VI = 10 V
7.92
7.84
VI
Operating Input Voltage
IO = 50 mA, VI = 10 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
VO
8.16
16
1
V
A
∆VO
Line Regulation
VI = 9 to 16 V,
IO = 5 mA
8
40
mV
∆VO
Load Regulation
VI = 9.3 V,
IO = 5 to 500 mA
8
40
mV
0.7
1.5
mA
Id
Quiescent Current
VI = 9 to 16V,
IO = 0mA
ON MODE
VI = 9.3 to 16V, IO = 500mA
OFF MODE
VI = 9 V
SVR
eN
Vd
Supply Voltage Rejection
IO = 5 mA
VI = 10 ± 1 V
Output Noise Voltage
Dropout Voltage
140
B = 10 Hz to 100 KHz
IO = 200 mA
72
67
57
50
0.2
0.35
IO = 500 mA
0.4
0.7
VIL
Control Input Logic Low
Ta = -40 to 125°C
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 9 V,
II
70
f = 120 Hz
f = 1 KHz
f = 10 KHz
VIH
CO
12
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
dB
0.8
2
IO = 0 to 500 mA
2
µA
µV
V
V
V
10
µA
10
µF
19/34
LF00 SERIES
ELECTRICAL CHARACTERISTICS FOR LF80C (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
VO
Parameter
Test Conditions
Min.
Typ.
Max.
Unit
8
8.16
V
Output Voltage
IO = 50 mA, VI = 10 V
7.84
7.68
VI
Operating Input Voltage
IO = 50 mA, VI = 10 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
8.32
16
V
1
∆VO
Line Regulation
VI = 9 to 16 V,
∆VO
Load Regulation
VI = 9.3 V,
Quiescent Current
VI = 9 to 16V,
IO = 5 mA
8
40
mV
8
40
mV
ON MODE
0.7
1.5
mA
VI = 9 V
OFF MODE
70
140
Supply Voltage Rejection
IO = 5 mA
VI = 10 ± 1 V
f = 120 Hz
f = 1 KHz
f = 10 KHz
eN
Vd
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
72
67
57
50
0.2
IO = 500 mA
0.4
VIL
Control Input Logic Low
VIH
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 9 V,
Id
IO = 5 to 500 mA
A
IO = 0mA
VI = 9.3 to 16V, IO = 500mA
SVR
II
CO
12
Ta = -40 to 125°C
µA
dB
0.35
µV
V
0.7
0.8
V
2
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
IO = 0 to 500 mA
2
V
10
µA
10
µF
ELECTRICAL CHARACTERISTICS FOR LF85AB (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
Parameter
Test Conditions
Min.
Typ.
Max.
Unit
8.5
8.585
V
Output Voltage
IO = 50 mA, VI = 10.5 V
8.415
8.33
VI
Operating Input Voltage
IO = 50 mA, VI = 10.5 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
VO
8.67
16
1
V
A
∆VO
Line Regulation
VI = 9.5 to 16 V,
IO = 5 mA
8
42
mV
∆VO
Load Regulation
VI = 9.8 V,
IO = 5 to 500 mA
8
42
mV
0.7
1.5
mA
Id
Quiescent Current
VI = 9.5 to 16V, IO = 0mA
ON MODE
VI = 9.8 to 16V, IO = 500mA
OFF MODE
VI = 9 V
SVR
eN
Vd
Supply Voltage Rejection
IO = 5 mA
VI = 10.5 ± 1 V
Output Noise Voltage
Dropout Voltage
0.35
IO = 500 mA
0.4
0.7
Control Input Logic Low
Ta = -40 to 125°C
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 9 V,
20/34
f = 120 Hz
f = 1 KHz
f = 10 KHz
140
B = 10 Hz to 100 KHz
IO = 200 mA
VIL
II
70
72
67
57
50
0.2
VIH
CO
12
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
dB
0.8
2
IO = 0 to 500 mA
2
µA
µV
V
V
V
10
µA
10
µF
LF00 SERIES
ELECTRICAL CHARACTERISTICS FOR LF85C (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
VO
Parameter
Test Conditions
Min.
Typ.
8.5
Output Voltage
IO = 50 mA, VI = 10.5 V
8.33
8.16
VI
Operating Input Voltage
IO = 50 mA, VI = 10.5 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
Max.
Unit
8.67
V
8.84
16
A
∆VO
Line Regulation
VI = 9.5 to 16 V,
IO = 5 mA
∆VO
Load Regulation
VI = 9.8 V,
IO = 5 to 500 mA
Quiescent Current
VI = 9.5 to 16V, IO = 0mA
ON MODE
VI = 9.8 to 16V, IO = 500mA
VI = 9 V
OFF MODE
70
140
Supply Voltage Rejection
IO = 5 mA
VI = 10.5 ± 1 V
f = 120 Hz
f = 1 KHz
f = 10 KHz
eN
Vd
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
72
67
57
50
0.2
IO = 500 mA
0.4
VIL
Control Input Logic Low
VIH
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 9 V,
Id
SVR
II
CO
V
1
8
42
mV
8
42
mV
0.7
1.5
mA
12
Ta = -40 to 125°C
µA
dB
0.35
µV
V
0.7
0.8
V
2
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
IO = 0 to 500 mA
2
V
10
µA
10
µF
ELECTRICAL CHARACTERISTICS FOR LF90AB (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
Parameter
Test Conditions
Min.
Typ.
9
Output Voltage
IO = 50 mA, VI = 11 V
8.91
8.82
VI
Operating Input Voltage
IO = 50 mA, VI = 11 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
VO
Max.
Unit
9.09
V
9.18
16
1
V
A
∆VO
Line Regulation
VI = 10 to 16 V,
IO = 5 mA
9
45
mV
∆VO
Load Regulation
VI = 10.3 V,
IO = 5 to 500 mA
9
45
mV
0.7
1.5
mA
Id
Quiescent Current
VI = 10 to 16V, IO = 0mA
ON MODE
VI = 10.3 to 16V,IO = 500mA
SVR
eN
Vd
VI = 10 V
OFF MODE
70
Supply Voltage Rejection
IO = 5 mA
VI = 11 ± 1 V
f = 120 Hz
f = 1 KHz
f = 10 KHz
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
71
66
56
50
0.2
0.35
IO = 500 mA
0.4
0.7
VIL
Control Input Logic Low
Ta = -40 to 125°C
VIH
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 10 V,
II
CO
12
IO = 0 to 500 mA
2
µA
dB
0.8
2
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
140
µV
V
V
V
10
µA
10
µF
21/34
LF00 SERIES
ELECTRICAL CHARACTERISTICS FOR LF90C (refer to the test circuits, Tj = 25°C, C I = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
VO
Parameter
Test Conditions
Min.
Typ.
9
Output Voltage
IO = 50 mA, VI = 11 V
8.82
8.64
VI
Operating Input Voltage
IO = 50 mA, VI = 11 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
Max.
Unit
9.18
V
9.36
16
1
∆VO
Line Regulation
VI = 10 to 16 V,
IO = 5 mA
∆VO
Load Regulation
VI = 10.3 V,
IO = 5 to 500 mA
Quiescent Current
VI = 10 to 16V, IO = 0mA
9
V
A
45
mV
9
45
mV
ON MODE
0.7
1.5
mA
VI = 10 V
OFF MODE
70
140
Supply Voltage Rejection
IO = 5 mA
VI = 11 ± 1 V
f = 120 Hz
f = 1 KHz
f = 10 KHz
eN
Vd
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
71
66
56
50
0.2
IO = 500 mA
0.4
VIL
Control Input Logic Low
VIH
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 10 V,
Id
VI = 10.3 to 16V,IO = 500mA
SVR
II
CO
12
Ta = -40 to 125°C
dB
0.35
2
Output Bypass Capacitance ESR = 0.1 to 10 Ω
IO = 0 to 500 mA
2
µV
V
0.7
0.8
VC = 6 V
µA
V
V
10
µA
10
µF
ELECTRICAL CHARACTERISTICS FOR LF120AB (refer to the test circuits, Tj = 25°C, CI = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
Parameter
Test Conditions
Min.
Typ.
Max.
Unit
12
12.12
V
Output Voltage
IO = 50 mA, VI = 15 V
11.88
11.76
VI
Operating Input Voltage
IO = 50 mA, VI = 15 V, Ta = -25 to 85°C
IO = 500 mA
IO
Output Current Limit
VO
12.24
16
1
V
A
∆VO
Line Regulation
VI = 13 to 16 V,
IO = 5 mA
12
60
mV
∆VO
Load Regulation
VI = 13.3 V,
IO = 5 to 500 mA
12
60
mV
0.7
1.5
mA
Id
Quiescent Current
VI = 13 to 16V, IO = 0mA
ON MODE
VI = 13.3 to 16V,IO = 500mA
SVR
eN
Vd
VI = 13 V
OFF MODE
70
Supply Voltage Rejection
IO = 5 mA
VI = 14 ± 1 V
f = 120 Hz
f = 1 KHz
f = 10 KHz
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
69
64
54
50
0.2
0.35
IO = 500 mA
0.4
0.7
VIL
Control Input Logic Low
Ta = -40 to 125°C
VIH
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 13 V,
II
CO
22/34
12
IO = 0 to 500 mA
2
µA
dB
0.8
2
VC = 6 V
Output Bypass Capacitance ESR = 0.1 to 10 Ω
140
µV
V
V
V
10
µA
10
µF
LF00 SERIES
ELECTRICAL CHARACTERISTICS FOR LF120C (refer to the test circuits, Tj = 25°C, CI = 0.1 µF,
CO = 2.2 µF unless otherwise specified.)
Symbol
Parameter
Test Conditions
VO
Output Voltage
IO = 50 mA, VI = 14 V
IO = 50 mA, VI = 14 V, Ta = -25 to 85°C
VI
Operating Input Voltage
IO = 500 mA
IO
Output Current Limit
Min.
Typ.
Max.
Unit
11.76
12
12.24
V
11.52
12.48
16
V
60
mV
1
∆VO
Line Regulation
VI = 13 to 16 V,
IO = 5 mA
∆VO
Load Regulation
VI = 13.3 V,
IO = 5 to 500 mA
Quiescent Current
VI = 13 to 16V, IO = 0mA
12
A
12
60
mV
ON MODE
0.7
1.5
mA
VI = 13 V
OFF MODE
70
140
Supply Voltage Rejection
IO = 5 mA
VI = 14 ± 1 V
f = 120 Hz
f = 1 KHz
f = 10 KHz
eN
Vd
Output Noise Voltage
Dropout Voltage
B = 10 Hz to 100 KHz
IO = 200 mA
69
64
54
50
0.2
IO = 500 mA
0.4
VIL
Control Input Logic Low
VIH
Control Input Logic High
Ta = -40 to 125°C
Control Input Current
VI = 13 V,
Id
VI = 13.3 to 16V,IO = 500mA
SVR
II
CO
12
Ta = -40 to 125°C
Output Bypass Capacitance ESR = 0.1 to 10 Ω
dB
0.35
2
IO = 0 to 500 mA
2
µV
V
0.7
0.8
VC = 6 V
µA
V
V
10
µA
10
µF
23/34
LF00 SERIES
TYPICAL PERFORMANCE CHARACTERISTICS (unless otherwise specified VO(NOM) = 3.3 V)
Figure 1 : Dropout Voltage vs Output Current
Figure 4 : Supply Current vs Input Voltage
Figure 2 : Dropout Voltage vs Temperature
Figure 5 : Short Circuit Current vs Input Voltage
Figure 3 : Supply Current vs Input Voltage
Figure 6 : Supply Current vs Temperature
24/34
LF00 SERIES
Logic Controlled Precision 3.3/5.0V Selectable Output
Sequential Multi-Output Supply
25/34
LF00 SERIES
Multiple Supply With ON/OFF Toggle Switch
Basic Inhibit Functions
26/34
LF00 SERIES
Delayed Turn-On
Low Voltage Bulb Blinker
27/34
LF00 SERIES
PENTAW ATT (VERTICAL) MECHANICAL DATA
DIM.
A
C
D
D1
E
F
F1
G
G1
H2
H3
L
L1
L2
L3
L5
L6
L7
M
M1
Dia1
MIN.
2.4
1.2
0.35
0.8
1
3.2
6.6
mm.
TYP
3.4
6.8
10.05
MAX.
4.8
1.37
2.8
1.35
0.55
1.05
1.4
3.6
7
10.4
10.4
MIN.
inch
TYP.
0.094
0.047
0.014
0.031
0.039
0.126
0.260
0.134
0.268
0.396
17.85
15.75
21.4
22.5
2.6
15.1
6
0.703
0.620
0.843
0.886
3
15.8
6.6
0.102
0.594
0.236
4.5
4
3.65
MAX.
0.189
0.054
0.110
0.053
0.022
0.041
0.055
0.142
0.276
0.409
0.409
0.118
0.622
0.260
0.177
0.157
3.85
0.144
0.152
P010E
28/34
LF00 SERIES
TO-220 MECHANICAL DATA
DIM.
mm.
MIN.
MAX.
MIN.
A
4.40
4.60
0.173
0.181
C
1.23
1.32
0.048
0.051
D
2.40
2.72
0.094
0.107
D1
TYP
inch
1.27
TYP.
MAX.
0.050
E
0.49
0.70
0.019
0.027
F
0.61
0.88
0.024
0.034
F1
1.14
1.70
0.044
0.067
F2
1.14
1.70
0.044
0.067
G
4.95
5.15
0.194
0.203
G1
2.4
2.7
0.094
0.106
H2
10.0
10.40
0.393
L2
16.4
0.409
0.645
L4
13.0
14.0
0.511
0.551
L5
2.65
2.95
0.104
0.116
L6
15.25
15.75
0.600
0.620
L7
6.2
6.6
0.244
0.260
L9
3.5
3.93
0.137
0.154
DIA.
3.75
3.85
0.147
0.151
P011C
29/34
LF00 SERIES
TO-220FP MECHANICAL DATA
mm.
DIM.
MIN.
inch
TYP
MAX.
MIN.
TYP.
MAX.
A
4.40
4.60
0.173
0.181
B
2.5
2.7
0.098
0.106
D
2.5
2.75
0.098
0.108
E
0.45
0.70
0.017
0.027
F
0.75
1
0.030
0.039
F1
1.15
1.50
0.045
0.059
F2
1.15
1.50
0.045
0.059
G
4.95
5.2
0.194
0.204
G1
2.4
2.7
0.094
0.106
H
10.0
10.40
0.393
0.409
L2
16
0.630
28.6
30.6
1.126
1.204
L4
9.8
10.6
0.385
0.417
L6
15.9
16.4
0.626
0.645
L7
9
9.3
0.354
0.366
DIA.
3
3.2
0.118
0.126
B
D
A
E
L3
L3
L6
F2
H
G
G1
¯
F
F1
L7
1 2 3
L2
L4
7012510/F
30/34
LF00 SERIES
DPAK MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
MAX.
MIN.
TYP.
MAX.
A
2.2
2.4
0.086
0.094
A1
0.9
1.1
0.035
0.043
A2
0.03
0.23
0.001
0.009
B
0.64
0.9
0.025
0.035
B2
5.2
5.4
0.204
0.212
C
0.45
0.6
0.017
0.023
C2
0.48
0.6
0.019
0.023
D
6
6.2
0.236
0.244
E
6.4
6.6
0.252
0.260
G
4.4
4.6
0.173
0.181
H
9.35
10.1
0.368
0.397
L2
L4
0.8
0.6
0.031
1
0.023
0.039
0068772-B
31/34
LF00 SERIES
PPAK MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
MAX.
MIN.
TYP.
MAX.
A
2.2
2.4
0.086
0.094
A1
0.9
1.1
0.035
0.043
A2
0.03
0.23
0.001
0.009
B
0.4
0.6
0.015
0.023
B2
5.2
5.4
0.204
0.212
C
0.45
0.6
0.017
0.023
C2
0.48
0.6
0.019
0.023
D
6
6.2
0.236
0.244
E
6.4
6.6
0.252
0.260
G
4.9
5.25
0.193
0.206
G1
2.38
2.7
0.093
0.106
H
9.35
10.1
0.368
0.397
L2
L4
0.8
0.6
0.031
1
0.023
0.039
0078180-B
32/34
LF00 SERIES
Tape & Reel DPAK-PPAK MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
A
MAX.
MIN.
TYP.
180
13.0
7.086
C
12.8
D
20.2
0.795
N
60
2.362
T
13.2
MAX.
0.504
0.512
14.4
0.519
0.567
Ao
6.80
6.90
7.00
0.268
0.272
0.2.76
Bo
10.40
10.50
10.60
0.409
0.413
0.417
Ko
2.55
2.65
2.75
0.100
0.104
0.105
Po
3.9
4.0
4.1
0.153
0.157
0.161
P
7.9
8.0
8.1
0.311
0.315
0.319
33/34
LF00 SERIES
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from
its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications
mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information
previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or
systems without express written approval of STMicroelectronics.
© The ST logo is a registered trademark of STMicroelectronics
© 2003 STMicroelectronics - Printed in Italy - All Rights Reserved
STMicroelectronics GROUP OF COMPANIES
Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco
Singapore - Spain - Sweden - Switzerland - United Kingdom - United States.
© http://www.st.com
34/34