3.3V Surface Mount Crystal Clock Oscillator HSM6 Features: XO) 2111 Comprehensive Drive 2111 Comprehensive Drive Aurora, Illinois 60505 Aurora, Illinois 60505 Phone: 630- 851- 4722 Phone: 630- 851- 4722 Fax: 630- 851- 5040 Fax: 630- 851- 5040 www.conwin.com www.conwin.com US Headquarters: 630-851-4722 European Headquarters: +353-61-472221 1.0 to 170 MHz 3.3V Operation RoHS Compliant Tri-State Enable/Disable Power Saving Function: 10uA When Disabled Overall Frequency Tolerance: HSM613 ± 25 ppm HSM623 ± 50 ppm HSM633 ± 100 ppm Temperature Range: -40 to 85°C Ceramic Surface Mount Package Tape and Reel Packaging The Connor-Winfield HSM613, HSM623, and HSM633 are 7.5mm x 5mm, 3.3V HCMOS, Surface Mount, Fixed Frequency Crystal Oscillators (XO) designed for use in all applications requiring precision clocks. The RoHS compliant surface mount package is designed for high-density mounting and is optimum for mass production. Absolute Maximum Ratings Parameter Minimum Storage Temperature Supply Voltage (Vcc) -55 -0.5 Nominal - Maximum 125 5.0 Units Notes Units Notes ppm 1 °C Vdc Operating Specifications Parameter Minimum Nominal Maximum Frequency Range (Fo) 1.0 - HSM613 125 HSM623 170 HSM633 170 Frequency Tolerance - HSM613 -25 25 HSM623 -50 50 HSM633 -100 100 Operating Temp Range -40 85 Supply Voltage (Vdd) 3.0 3.3 3.6 Supply Current (Icc) - 1.000 to 31.999 MHz 15 32 to 49.999 MHz 20 50 to 66.999 MHz 25 67 to 124.999 MHz 40 125 to 170 MHz 50 MHz °C Vdc mA Input Characteristics Parameter Enable Voltage - (Vih) Disable Voltage - (Vil) Enable Time Disable Time Output Disable Current (lcc) Minimum ≥ 70% Vdd - Nominal - Maximum ≤ 30% Vdd 10 150 10 Units Notes Units Notes Vdc Vdc mS nS uA 2 HCMOS Output Characteristics Parameter Bulletin Revision Date Sm044 13 27 March 2012 Load Voltage High (Voh) Low (Vol) Current High (loh) Low (lol) Duty Cycle at 50% of Vcc Rise / Fall Time: 20% to 80% 1.000 to 19.999 MHz 20.00 to 49.999 MHz 50.00 to 99.9999 MHz 100.00 to 170 MHz Start-Up Time Jitter (10 Hz to 20 MHz) (12 kHz to 20 MHz) Minimum 2.91 -2 45 - Nominal 50 3.0 2.0 1.5 0.5 - Maximum 15 0.33 2 55 6.0 4.0 3.0 1.0 10 5 1 pF Vdc mA % nS mS pS RMS Notes: 1. Inclusive of calibration @ 25°C , frequency stability vs temperature, supply voltage change, load change, shock and vibration, 10 years aging. 2. Oscillator output is enabled with no connection on pad 1 Specifications subject to change without notice. All dimensions in inches. © Copyright 2012 The Connor-Winfield Corporation 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Package Characteristics Package Suggested Pad Layout Hermetically sealed ceramic package and metal cover Environmental Characteristics Temperature Cycle The specimen shall meet electrical characteristics after tested 5 cycles of -55°C / 30 minutes and +125°C / 30 minutes Hermetical No bubbles appear in Flourinert (FC-43) at 125°C ±5°C for 5 minutes Solvent Resistance Marking will withstand immersion in Isopropyl Alcohol or Trichloroethylene Soldering General Conditions 260°C max x 10 sec max x 2 times max or 230°C max x 180 sec max x 1 time Typical Operation Data (Vapor phase reflow) 20 to 100 sec up to 215°C, 50 sec at 215°C, then down to room temperature per 1 to 5°C / sec Test Circuit Mechanical Characteristics Free Drop The specimen shall meet electrical characteristics after tested 3 times, Free Drop testing on the hard wooden board from a height of 75 cm. Vibration The specimen shall meet electrical characteristics after tested by the following conditions: 10-55Hz 1.5mm Amplitude, 55-2000 Hz 20 G's, 2 hours for each plane Thermal Shock After applied Thermal Shock of 260°C max x 10 sec max x 2 times, or 230°C max x 180 sec max, the specimen shall meet electrical characteristics Solderability (EIAJ-RCX-0102.101 Condition 1a) 1) Flux: MIL-F-14256 (WW Rosin=25%, Isopropyl Alcohol = 75%) 2) Solder: QQ-S-571 (Sn = 63%, Pb = 37%) 3) Solder bath temperature: 235°C ±5°C 4) Depth of immersion: Up to electrical terminal 5) Immersing time: Within 2 sec ±0.5 sec into solder bath Output Waveform TF TR "1" LEVEL After performing the above procedures, a newly soldered coverage shall be greater than 90% 80% 50% Pin Connections 1: Tri-State E/D 2: Ground 3: Output 4: VDD 20% "0" LEVEL SYMMETRY Ordering Information Dimensional Tolerance: ±.02” (.508mm) ±.005” (.127mm) HSM633 - Tape and Reel Dimensions 125.0M CLOCK SERIES CENTER FREQUENCY Bulletin Revision Dimensional Tolerance: ±.02” (.508mm) ±.005” (.127mm) Specifications subject to change without notice. All dimensions in inches. © Copyright 2012 The Connor-Winfield Corporation Date Sm044 13 27 March 2012