ODLC-45 45W Constant Current Mode LED Driver F M ■ Features Constant Current mode output Flicker free design Plastic housing with class II design Built-in active PFC function No load power consumption<0.5W(Blank-Type) IP67 rating for indoor or outdoor installations Function options: 2 in 1 dimming (dim-to-off); M SELV IP67 series Type HL ■ Applications LED panel lighting LED flood lighting Indoor LED lighting Auxiliary DC output 3 years warranty ■ Description ODLC-45 series is a 45W LED AC/DC driver featuring the constant current mode output with flicker free design.ODLC-45 operates from 90~295VAC and offers models with different rated current ranging between 350mA and 1400mA. Thanks to the efficiency up to 86%, with the fanless design, the entire series is able to operate for -20℃~+85℃ case temperature under free convection. The design of plastic housing and IP67 ingress protection level allows this series to fit indoor wet applications. ODLC-45 is equipped with various function options, such as dimming methodologies, so as to provide the optimal design flexibility for lighting system. ■ Model Encoding ODLC - 45 A - 350 Rated output current(350/500/700/1050/1400mA) Function options Rated wattage Series name Type Blank A Function 2 in 1 dimming (0~10VDC and 10V PWM) 2 in 1 dimming , Auxiliary DC output Note In Stock In Stock File Name:ODLC-45-SPEC 2016-10-26 ODLC-45 45W Constant Current Mode LED Driver series SPECIFICATION ODLC-45 -350 ODLC-45 -500 ODLC-45 -700 ODLC-45 -1050 ODLC-45 -1400 RATED CURRENT 350mA 500mA 700mA 1050mA 1400mA RATED POWER 33.25W 45W 44.8W 45.15W 44.8W CONSTANT CURRENT REGION Note.2 57 ~ 95V 54 ~ 90V 38 ~ 64V 26 ~ 43V 19 ~ 32V OPEN CIRCUIT VOLTAGE(max.) 118V 115V 84V 63V 50V 84% 83% MODEL OUTPUT CURRENT RIPPLE 5% max. @rated current CURRENT TOLERANCE ±7.0% SETUP TIME 500ms / 230VAC 1200ms/115VAC Note.4 AUXILIARY DC OUTPUT Note.5 Nominal 12V(deviation 11.4~12.6)@50mA for A-Type only VOLTAGE RANGE Note.3 FREQUENCY RANGE INPUT 90 ~ 295VAC 127 ~ 417VDC (Please refer to "STATIC CHARACTERISTIC" section) 47 ~ 63Hz POWER FACTOR (Typ.) PF>0.95/115VAC, PF>0.92/230VAC, PF>0.9/277VAC@full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section) TOTAL HARMONIC DISTORTION THD< 20%(@load≧60%/230VAC; @load≧75%/277VAC) (Please refer to “TOTAL HARMONIC DISTORTION” section) EFFICIENCY (Typ.) 86% AC CURRENT 0.6A/115VAC 0.4A/230VAC INRUSH CURRENT (Typ.) COLD START 30A(twidth=100μs measured at 50% Ipeak) at 230VAC; Per NEMA 410 85% 85% 0.3A/277VAC MAX. No. of PSUs on 16A 32 units (circuit breaker of type B) / 32 units (circuit breaker of type C) at 230VAC CIRCUIT BREAKER LEAKAGE CURRENT <0.75mA / 277VAC NO LOAD POWER CONSUMPTION <0.5W for Blank-Type PROTECTION SHORT CIRCUIT Hiccup mode, recovers automatically after fault condition is removed WORKING TEMP. Tcase=-20 ~ +85℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section) MAX. CASE TEMP. Tcase=+85℃ WORKING HUMIDITY 20 ~ 90% RH non-condensing ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +80℃, 10 ~ 95% RH TEMP. COEFFICIENT ±0.03%/℃ (0 ~ 40℃) VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes SAFETY STANDARDS UL8750 (type”HL”) ,CSA C22.2 NO.250.13-12; ENEC EN61347-1 & EN61347-2-13 independent, EN62384,GB19510.1,GB19510.14; WITHSTAND VOLTAGE I/P-O/P:3.75KVAC IP67 approved SAFETY & ISOLATION RESISTANCE I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH EMC Compliance to EN55015, EN61000-3-2 Class C (@load≧60%) ; EN61000-3-3,GB17743,GB17625.1 EMC EMISSION EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, light industry level( surge immunity:Line-Line:1KV ) MTBF 408.8Khrs min. OTHERS DIMENSION PACKING NOTE MIL-HDBK-217F (25℃) 111*77*28.5mm(L*W*H) 0.42Kg; 24pcs/ 11Kg/ 0.72CUFT 1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25℃ of ambient temperature. 2. Please refer to "DRIVING METHODS OF LED MODULE". 3. De-rating may be needed under low input voltages. Please refer to STATIC CHARACTERISTIC sections for details. 4. Length of set up time is measured at cold first start. Turning ON/OFF the driver may lead to increase of the set up time. 5. There is no design of short circuit protection for the Auxiliary DC output; this function can not be used when dimming input terminals(DIM+,DIM-) are short circuit or when it is no load or short circuit at output(Vo+,Vo-). 6. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. File Name:ODLC-45-SPEC 2016-10-26 ODLC-45 45W Constant Current Mode LED Driver series Block Diagram fosc : 70KHz AUX+(for A-Type) AUX-(for A-Type) RECTIFIERS I/P EMI FILTER & RECTIFIERS RECTIFIERS & FILTER POWER SWITCHING O.L.P. PWM&PFC CONTROL CURRENT LIMIT Vo+ VoDIM+ DIM- DETECTION CIRCUIT DRIVING METHODS OF LED MODULE ※ This series works in constant current mode to directly drive the LEDs. In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. 100 Vo(%) Constant Current area Should there be any compatibility issues, please contact MEAN WELL. 60 (min.) Hiccup Protection 50 100 Io(%) Typical output current normalized by rated current (%) File Name:ODLC-45-SPEC 2016-10-26 ODLC-45 45W Constant Current Mode LED Driver series DIMMING OPERATION ※ 2 in 1 dimming function AUX-(Green) AUX+(Yellow) V 0 -(Black) V 0 +(Red) DIM-(Gray) DIM+(Purple) ACN(Blue) ACL(Brown) Output constant current level can be adjusted by applying one of the two methodologies between DIM+ and DIM-: 0 ~ 10VDC, or 10V PWM signal. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. ◎ Applying additive 0 ~ 10VDC 100% 90% -V + + - - DIM+ + Output current (%) 80% +V 70% 60% 50% 40% 30% Additive Voltage - 20% DIM- 10% “DO NOT connect "DIM- to Vo-" 0% 0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage ◎ Applying additive 10V PWM signal (frequency range 300Hz ~ 3KHz): 100% 90% -V + + - - DIM+ Additive PWM signal Output current (%) 80% +V 70% 60% 50% 40% 30% 20% DIM“DO NOT connect "DIM- to Vo-" 10% 0% 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input Note : 1. Min. dimming level is about 8% and the output current is not defined when 0%< I out<8%. 2. The output current could drop down to 0% when dimming input is about 0Vdc or 10V PWM signal with 0% duty cycle. File Name:ODLC-45-SPEC 2016-10-26 ODLC-45 45W Constant Current Mode LED Driver series OUTPUT LOAD vs TEMPERATURE 90~295VAC for 350mA Model,200~295VAC for others 90~295VAC for 350mA Model,200~295VAC for others 100 100 80 80 90~200VAC for models other than 350mA Model 40 20 -20 -10 0 10 20 90~200VAC for models other than 350mA Model 60 LOAD (%) LOAD (%) 60 30 40 (HORIZONTAL) 50 40 20 -20 -10 0 15 30 45 60 (HORIZONTAL) 85 CASE TEMPERATURE (℃) AMBIENT TEMPERATURE,Ta (℃) STATIC CHARACTERISTIC POWER FACTOR (PF) CHARACTERISTIC ※ Tcase at 75℃ 100 1 for 350mA Model 90 0.95 80 PF LOAD (%) 0.9 for others 70 60 50 277V 0.85 230V 115V 0.8 40 0.75 90 135 180 0.7 295 200 50% 60% 70% 80% 90% INPUT VOLTAGE (V) (45W) LOAD ※De-rating is needed under low input voltage. TOTAL HARMONIC DISTORTION (THD) EFFICIENCY vs LOAD ODLC-45 series possess superior working efficiency that up to 86% can be reached in field applications. ※ 350mA Model,Tcase at 75℃ ※ 350mA Model,Tcase at 75℃ 16 90 14 88 12 10 277V 8 230V 6 115V 4 2 EFFICIENCY(%) THD(%) 100% 86 84 277V 82 230V 115V 80 78 0 50% 60% 70% LOAD 80% 90% 100% 76 50% 60% 70% 80% 90% 100% LOAD File Name:ODLC-45-SPEC 2016-10-26 ODLC-45 45W Constant Current Mode LED Driver MECHANICAL SPECIFICATION Case No.ODLC-45A series Unit:mm 111 3.5 ※ Blank-Type: 3.5 200±10 Vo-(Black) Vo+(Red) DIM-(Gray) DIM+(Purple) 77 30 30 ACN(Blue) ACL(Brown) 3.5 tc 150±10 200±10 2*ψ4.5 3.5 : Max. Case Temperature 28.5 tc DC wire No. Assignment(DC OUT) ACN(Blue) SVT 18AWG Vo-(Black) UL1007 18AWG ACL(Brown) SVT 18AWG Vo+(Red) UL1007 18AWG DIM-(Gray) UL1007 22AWG 2.5 AC wire No. Assignment(AC IN) DIM+(Purple) UL1007 22AWG ※ A-Type: 3.5 111 3.5 200±10 150±10 AUX-(Green) AUX+(Yellow) Vo-(Black) Vo+(Red) DIM-(Gray) DIM+(Purple) 77 30 150±10 30 ACN(Blue) ACL(Brown) 3.5 tc 200±10 : Max. Case Temperature 2*ψ4.5 3.5 AC wire No. Assignment(AC IN) DC wire No. Assignment(DC OUT) ACN(Blue) SVT 18AWG AUX-(Green) UL1007 22AWG ACL(Brown) SVT 18AWG AUX+(Yellow) UL1007 22AWG Vo-(Black) UL1007 18AWG Vo+(Red) UL1007 18AWG DIM-(Gray) UL1007 22AWG 2.5 28.5 tc DIM+(Purple) UL1007 22AWG INSTALLATION MANUAL Please refer to : http://www.meanwell.com/manual.html File Name:ODLC-45-SPEC 2016-10-26