规格书编号 SPEC NO : 产品规 格 书 SPECIFICATION CUSTOMER 客 户： PRODUCT 产 品： SAW FILTER MODEL NO 型 号： HDF865C SMD-4 MARKING 印 字： HDF4864 PREPARED 编 制： CHECKED 审 核： APPROVED 批 准： D A T E 日 期： 2011-6-13 客户确认 CUSTOMER RECEIVED: 审核 CHECKED 批准 APPROVED 日期 DATE 无锡市好达电子有限公司 Shoulder Electronics Limited www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 1 of 7 SAW FILTER HDF865C S-4 1. Package Dimension 3.Performance 3.1Application Low-Loss SAW Filter of cordless system. Center Frequency:865MHz 3.2Maximum Rating Operation Temperature Range www.shoulder.cn -40℃ to +85℃ Storage Temperature Range -45℃to +85℃ DC. Permissive Voltage 10 V DC Maximum Input Power 10 dBm Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 2 of 7 SAW FILTER HDF865C S-4 3.3 Electronic Characteristics(-10~60℃) Center Frequency Insertion Loss (860 MHz ~870 MHz) Amplitude Ripple (860 MHz ~870 MHz) Relative Attenuation 0.3 MHz ~ 850 MHz 900 MHz ~ 1200MHz Input/Output Impedance Unit Minimum Typical Maximum MHz dB dB - 865 - 2.5 1.0 4.0 2.5 dB 38 40 42 45 50 - Ohms 3.4 Frequency Characteristics www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 3 of 7 SAW FILTER HDF865C S-4 3.5 Test Circuit 4. ENVIRONMENTAL CHARACTERISTICS 4-1 High temperature exposure Subject the device to +85℃ for 16 hours. Then release the filter into the room conditions for 24 hours prior to the measurement. It shall fulfill the specifications in 3.3. 4-2 Low temperature exposure Subject the device to -40℃ for 16 hours. Then release the device into the room conditions for 24 hours prior to the measurement. It shall fulfill the specifications in 3.3. 4-3 Temperature cycling Subject the device to a low temperature of -40℃ for 30 minutes. Following by a high temperature of +85℃ for 30 Minutes. Then release the device into the room conditions for 24 hours prior to the measurement. It shall meet the specifications in 3.3. 4-4 Resistance to solder heat Dip the device terminals no closer than 1.5mm into the solder bath at 260℃ ±10℃ for 10±1 sec. Then release the device into the room conditions for 4 hours. The device shall meet the specifications in 3.3. 4-5 Solderability Subject the device terminals into the solder bath at 245℃ ±5℃ for 5s, More than 95% area of the terminals must be covered with new solder. It shall meet the specifications in 3.3. 4-6 Mechanical shock Drop the device randomly onto the concrete floor from the height of 1m 3 times. the device shall fulfill the specifications in 3.3. 4-7 Vibration Subject the device to the vibration for 1 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 Hz. The device shall fulfill the specifications in 3.3. 5. REMARK 5.1 Static voltage www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 4 of 7 SAW FILTER HDF865C S-4 Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 5.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning 5.3 Soldering Only leads of component may be soldered . Please avoid soldering another part of component. 6. Packing 6.1 Dimensions (1) Carrier Tape: Figure 1 (2) Reel: Figure 2 (3) The product shall be packed properly not to be damaged during transportation and storage. 6.2 Reeling Quantity 1000 pcs/reel 7’’ 3000 pcs/reel 13’’ 6.3 Taping Structure (1) The tape shall be wound around the reel in the direction shown below. (2) Label Device Name User Product Name Quantity Lot No. (3) Leader part and vacant position specifications. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 5 of 7 SAW FILTER HDF865C S-4 7. TAPE SPECIFICATIONS 7.1 Tensile Strength of Carrier Tape: 4.4N/mm width 7.2 Top Cover Tape Adhesion (See the below figure) (1) pull off angle: 0~15º (2) speed: 300mm/min. (3) force: 20~70g [Figure 1] Carrier Tape Dimensions [Unit:mm] W F www.shoulder.cn E P0 P1 P2 Tel:0755-82916880 Fax:0755-82916881 D0 D1 t1 E-mail:[email protected] t2 A B Page 6 of 7 SAW FILTER 12.00 ±0.30 5.50 ±0.10 1.75 ±0.10 HDF865C S-4 4.00 ±0.10 4.00 ±0.10 2.00 ±0.10 Ø1.50 Ø1.5 ±0.25 0.31 ±0.05 1.30 ±0.10 3.4 MAX. 3.4 MAX [Figure 2] [Unit:mm] A B C D E W t r Ø330 ±1.0 Ø100 ±0.5 Ø13 ±0.5 Ø21 ±0.8 2 ±0.5 13 ±0.3 3 max. 1.0 max. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 7 of 7