Keysight M9203A PXIe High-Speed Digitizer/ Wideband Digital Receiver 2 channels, 12-bit, up to 3.2 GS/s, DC to 2 GHz bandwidth Data Sheet 02 | Keysight | M9203A PXIe High-Speed Digitizer/Wideband Digital Receiver - Data Sheet Overview Introduction The Keysight M9203A is a very fast and low noise PXIe HighSpeed Digitizer/Wideband Digital Receiver featuring wide analog bandwidth, making it ideal for wireless, radar and satellite communication applications or any application requiring wideband signal capture, and at the same time very high dynamic range. Thanks to its PCI Express ® backplane connection, the M9203A supports continuous data streaming to disk. Product description The M9203A is a dual-slot 3U PXIe 12-bit High-Speed Digitizer/ Wideband Digital Receiver running at 3.2 GS/s, with up to 2 GHz instantaneous analog bandwidth and providing a large 4 GB DDR3 acquisition memory. The M9203A features a large Xilinx Virtex-6 FPGA that can implement different functionalities depending on which firmware option you choose. The M9203A PXIe High-Speed Digitizer/Wideband Digital Receiver can also be combined with the Keysight 89600 VSA software for advanced dual-channel signal analysis. For information on other firmware options please contact Keysight Technologies: [email protected] Example applications –– Wireless communication (5G, LTE) –– Emerging communication standards (e.g. DOCSIS 3.1) –– Radar and wideband signal capture –– Radar and satellite communication applications –– Semiconductor automated test Product features –– 1 channel with 12-bit resolution up to 3.2 GS/s sampling rate with interleaving enabled –– 2 channels up to 1.6 GS/s simultaneous sampling rate –– DC up to 2 GHz bandwidth –– 50 Ω input impedance, DC coupled –– Selectable 1 V or 2 V full scale range (FSR) –– ±200 fs channel-to-channel skew stability –– 15 ps RMS trigger time interpolator (TTI) precision –– Up to 4 GB DDR3 on-board memory –– Enhanced real-time processing using Xilinx Virtex-6 FPGA –– Support for loading custom real-time processing –– High data throughput PCIe ® Gen2 (x8) backplane –– Real-time digital down-conversion (-DDC) with adjustable center frequency and analysis bandwidth –– Real-time digitizer raw data streaming and recording bundle –– Real-time digital down-conversion with I/Q data streaming (-CB0) and recording bundle (-CB2) Uncompromising values –– Fast PXIe 12-bit wideband digitizer with on-board real-time processing –– Capture wide bandwidth signals –– High dynamic range acquisition for better measurement fidelity –– Accurate long term measurement –– Capable of switching between multiple firmware programs –– Self-trigger mode for unequaled synchronous noise reduction –– Open FPGA for custom process –– Reduced test time by tuning and zooming on signals (-DDC) –– Up to 1 GHz baseband streaming and recording (-CB0) –– Dual channel phase coherent streaming and recording with up to 320 MHz alias protected IBW (-CB2) 03 | Keysight | M9203A PXIe High-Speed Digitizer/Wideband Digital Receiver - Data Sheet Hardware platform Product overview On-board real-time processing The M9203A is PXI Express compliant. Designed to benefit from fast data interfaces, the product can be integrated in PXIe and PXI Hybrid chassis slots. The PXI format offers high performance in a small, rugged package. It is an ideal deployment platform for many automated measurements systems. At the heart of the M9203A PXIe High-Speed Digitizer/Wideband Digital Receiver is a data processing unit (DPU) based on the powerful Xilinx Virtex-6 FPGA. This DPU is responsible for controlling the module functionality, data flow and real-time signal processing. This powerful feature allows data reduction and storage to be carried out at the digitizer level, minimizing transfer volumes and speeding-up analysis. Block diagram DPU FPGA DC Front-end ADC ADC IN 2 DC Front-end ADC ADC ADC ADC Custom real-time processing DDR3 SDRAM memory QDR2 SRAM memory DDR3 SDRAM memory PCIe switch REF IN CLK IN TRG IN TRG OUT I/O TimeBase Control Trigger Figure 1. Simplified block diagram of the M9203A PXIe High-Speed Digitizer/Wideband Digital Receiver. PCIe BUS IN 1 04 | Keysight | M9203A PXIe High-Speed Digitizer/Wideband Digital Receiver - Data Sheet Software Platform Keysight Software Suite Software applications Keysight IO Libraries Suite offers fast and easy connection to instruments and the newest version extends that capability to include modular instruments. In addition, the M9203A includes the Keysight MD2 soft front panel (SFP) graphical interface. This software application can be used to explore the capabilities of the Keysight modular highspeed digitizers. Drivers The module comes with the IviDigitizer class compliant Keysight MD2 IVI-COM and IVI-C drivers that work in the most popular development environments including Visual C/C++, C#, VB.NET, MATLAB, and LabVIEW. Linux is also supported using the IVI-C driver. Easy software integration To help you get started and complete complex tasks quickly, the M9203A PXIe Wideband Digitizer is supplied with a comprehensive portfolio of module drivers, documentation, examples, and software tools to help you quickly develop test systems with your software platform of choice. Compliance The M9203A is PXI Express compliant. Designed to benefit from fast data interfaces, the product can be integrated in PXIe and PXI Hybrid chassis slots. Figure 3. M9203A front panel with analog inputs and multiple I/O signals. Figure 2. MD2 software front panel (SFP) interface. For advanced measurement analysis, the M9203A PXIe HighSpeed Digitizer/Wideband Digital Receiver can be combined with Keysight’s 89600 Vector Signal Analysis software, the industry’s standard for signal analysis and demodulation. The M9203A allows fast connection to the 89600 VSA software through its high data throughput PCIe backplane, compared to traditional instruments. Figure 4. M9203A PXIe 12-bit High-Speed Digitizer/Wideband Digital Receiver offers a small size for easy integration within a PXIe chassis. 05 | Keysight | M9203A PXIe High-Speed Digitizer/Wideband Digital Receiver - Data Sheet Firmware Options The M9203A PXIe High-Speed Digitizer/Wideband Digital Receiver provides several firmware options: – DGT: Digitizer firmware – INT: Interleaved channel sampling functionality – FDK1: Custom firmware capablility – TSR 2: Triggered simultaneous acquisition and readout – DDC: Wideband real-time digital down-conversion Easy firmware switch A simple call to the configuration function will enable to switch to the required option. DGT digitizer firmware The digitizer firmware: –– Allows standard data acquisition, including: digitizer initialization, setting of the acquisition and clocking modes, management of channel triggering for best synchronization, storing data in the internal memory and/or transferring them through the backplane bus. –– Implements multi-record acquisition functionality. –– Supports fixed internal clocking frequency with internal or external reference, and variable frequency external clock. –– Offers programmable binary decimation to lower the sample rate by a factor of 2n where n is defined in the range 1 to 10 for single record. e.g. you can select from 1.6 GS/s down to 1.5625 MS/s. –– Trigger time interpolator (TTI): high precision integrated time to digital converter can be used to increase time measurement accuracy. INT interleaved channel sampling functionality This interleave option allows two channels to be combined and to reach 3.2 GS/s in one channel acquisition mode. FDK custom firmware capability This option enables loading4 custom firmware created with the U5340A FPGA development kit5. TSR triggered simultaneous acquisition and readout The triggered simultaneous acquisition and readout architecture allows to continuously acquire new records while reading previous ones. TSR solution is dedicated to applications requiring no trigger loss, achieving longer recording time when compares with standard digitizer (-DGT). TSR option main features: –– High trigger rate with guaranteed no lost trigger for specific configuration3. –– Easy to use solution, implementing an optimal and automated control of memory addressing. –– Selecting larger memory size option allows longer record size and provides larger buffer for data transfer to host PC, especially useful for applications with non-periodic trigger or very high trigger rate during a limited period. DDC real-time digital down-conversion The real-time digital down-conversion option (-DDC), in addition to the basic digitizer functionality, implements a real-time digital decimation and filtering on the digitized data, allowing the user to tune and zoom on the signals of interest. This exclusive IP algorithm provides very powerful and flexible digital downconversion on 2 channels. The filters and local oscillators (LO) are synchronized to maintain constant phase and timing relationships allowing phase-coherent post processing. The DDC provides three main functions: –– Frequency shifting (tune): Independently shifting each channels IF signal into baseband, allows the analysis bandwidth to be set around the signal of interest. –– Data reduction (zoom): Reducing the bandwidth and sample rate to match the analyzed signal decreases the amount of data that needs to be transferred for a given capture duration, in turn accelerating post-processing operations. –– Magnitude trigger: Setting the magnitude level that the down converted signal needs to achieve at a specified frequency and bandwidth to generate a digital trigger on all channels. These functions allow isolation of the signal of interest from other signals in a crowded spectrum, improved dynamic range as the integrated noise is reduced, and increased SNR and effective number of bits (ENOB). The resulting advantage for your application is a reduced test time, while improving overall test efficiency. 1. 2. 3. 4. 5. A calibration digitizer function is available with each firmware. Only available with DGT option. Please contact Keysight to find out the repetition rate that can be achieved in your application. On the Virtex-6 LX195T DPU FPGA. There are 11 W maximum power dedicated to FPGA processing, the custom firmware design must fit within this power provision. 06 | Keysight | M9203A PXIe High-Speed Digitizer/Wideband Digital Receiver - Data Sheet Firmware Development U5340A - FPGA Development Kit1 The FPGA development kit includes everything you need: source code, ready-to-use base design, a set of cores to easily interface to the underlying hardware, a test-bench environment for design and simulation, and automated building script. For more information: Keysight U5340A - FPGA Development Kit for High-Speed Digitizers Keysight product brochure 5991-2424EN http://literature.cdn.keysight.com/litweb/pdf/5991-2424EN.pdf 1. This standalone software package must be acquired separately. DDR3 Ctrl SRAM Ctrl DDR3 Ctrl Custom real-time processing PCIe Gen 2 There are several rationales to consider developing custom signal processing such as: – Data throughput optimization – Real time processing – Implementation of custom IP and OEM technical know-how – Re-usability and upgradability. ADC interface The FPGA development kit combines capabilities to: – Achieve multi GS/s real-time processing on a full digitizer framework by leveraging the full density and speed of the FPGA. – Shorten time-to-market with turn-key, easy-to-use development flow and debug. Calibration digitizer Configuration The FPGA development kit is primarily intended to open the design of the FPGA to specific user requirements by providing a development framework that interfaces to the underlying hardware. FPGA System monitoring Clock/reset manager Figure 5. Enlarged block diagram of the FPGA Xilinx Virtex-6 Predefined Keysight IP cores Custom real-time processing (using the FPGA development kit) 07 | Keysight | M9203A PXIe High-Speed Digitizer/Wideband Digital Receiver - Data Sheet Application Options1 For specific applications the M9203A PXIe High-Speed Digitizer/ Wideband Digital Receiver can be configured with specific options: –– CB0: Digitizer streaming and recording –– CB2: Digital down converter streaming and recording at 1.6 GS/s –– BB1: High fidelity digitizer CB0 digitizer streaming and recording CB0 is a turnkey reference bundle, based on the continuous simultaneous acquisition and readout architecture, implementing a real time digitizer data recorder for gapless acquisition. It includes a command line application ensuring performance of up to 2 GB/s2 in a specific qualified system. An easy to use data viewer application is also provided. This digitizer streaming and recording option with bundled applications provides: – Guaranteed recording specification – Various recording speed controlled by application – Adaptable sampling rate (decimation and external clock) – Data throughput optimization (12-bit, 10-bit or 8-bit mode). This option is added on top of a M9203A pre-configured version composed of: – 1.6 GS/s sampling rate (-SR2) or up to 2 GS/s (-SR2, -INT, with external clock) – Full bandwidth (-F10) – 4 GB acquisition memory (-M40) – Digitizer firmware (-DGT) The digitizer data streamer application is an intuitive command line application which allows to control the M9203A and adapts its data rate to the target application. The data viewer is a graphical user interface (GUI) application which allows to read, display, select and export the data stored. M9203A PXIe Digitizer Channel 2 Channel 1 2 GB/s Recommended Host PC Up to 3 GB/s SSD Data Storage Figure 6. Streaming options (-CB0, -CB2) are proposed with a recommended host PC and SSD. Performance is guaranteed with specific configurations 3. Maximum streaming and recording performance is guaranteed using an additional qualified host computer system with specific storage devices configuration.4 1. 2. 3. 4. Application options are delivered on the high-speed digitizer DVD. Equivalent to: 2 GS/s in 8-bit mode, 1.6 GS/s in 10-bit mode, and 1.3 GS/s in 12-bit mode. To reach the guaranteed performances the system requires both an external computer and data storage. Keysight proposes full system and installation services. Please contact support at [email protected] for additional information. CB2 digital down-conversion streaming and recording This bundle enables continuous gapless acquisition, implementing: –– Digital down converter functionality in real time –– Data steaming to host –– Multichannel recording to disk all I/Q samples for later analysis. –– Independent local-oscillators, with phase-coherency between channels. The -CB2 option is added on top of a M9203A pre-configured version composed of: –– 1.6 GS/s sampling rate (-SR2) –– Full bandwidth (-F10) –– 4 GB acquisition memory (-M40) –– Digitizer firmware (-DGT) This option provides: –– Guaranteed recording specification up to 320 MHz instantaneous bandwidth (IBW) with tunable intermediate frequency with recommended configuration. –– Data throughput optimization (I/Q samples with 32-bit, 16-bit or 12-bit mode). The option includes an intuitive command line application allowing to control the M9203A and a data viewer providing a simple graphical user interface (GUI) which allows to read, display, select and export the data stored. Maximum streaming and recording performance is guaranteed using an additional qualified host computer system with specific storage devices configuration.4 BB1 high fidelity digitizer This high fidelity digitizer option provides enhanced performance by: –– Compensating the ADC and front-end distortion –– Minimizing interleave spurs –– Reducing the overall noise bandwidth. This results in highly improved and uniform measurement fidelity across the useful bandwidth, which greatly benefits RF and wireless frequency domain measurements. The digitizer’s post processing compensation also delivers better spurious-free dynamic range (SFDR) and intermodulation product (IMx) specifications. This application option is pre-configured with: –– 1.6 GS/s sampling rate (-SR2) Leaving choice of bandwidth and memory, for optional use in -BB1 mode, recommendation is: – 650 MHz bandwidth (-F05) – 256 MB acquisition memory (-M02) It allows the following usage as high fidelity digitizer: –– 1.6 GS/s with 650 MHz bandwidth, up to 64 MSamples/ch. –– 800 MS/s with 400 MHz bandwidth, up to 32 MSamples/ch. –– 400 MS/s with 200 MHz bandwidth, up to 16 MSamples/ch. –– 200 MS/s with 100 MHz bandwidth, up to 8 MSamples/ch. –– 100 MS/s with 50 MHz bandwidth, up to 4 MSamples/ch. 08 | Keysight | M9203A PXIe High-Speed Digitizer/Wideband Digital Receiver - Data Sheet Technical Specifications and Characteristics Analog input (IN1 and IN2 SMA connectors) Number of channels 2 (without INT option), 2 or 1 (with INT option) Impedance 50 Ω ±2 % Coupling DC Full scale ranges (FSR) 1 V and 2 V Maximum input voltage 1V FSR: Clamp at ± 3.6 V, absolute maximum DC voltage rating ± 4.6 V 2V FSR: Clamp at ± 6.3 V, absolute maximum DC voltage rating ± 5.0 V Input voltage offset –2xFSR to +2xFSR Input frequency range (-3 dB bandwidth) -F05, -SR2 DC to 650 MHz (nominal) in 1V FSR at 1.6 GS/s DC to 650 MHz (nominal) in 2V FSR at 1.6 GS/s -F05, -SR2, -INT DC to 650 MHz (nominal) in 1V FSR at 3.2 GS/s DC to 650 MHz (nominal) in 2V FSR at 3.2 GS/s -F10, -SR2 DC to 1.9 GHz (nominal) in 1V FSR at 1.6 GS/s DC to 2.0 GHz (nominal) in 2V FSR at 1.6 GS/s -F10, -SR2, -INT DC to 1.4 GHz (nominal) in 1V FSR at 3.2 GS/s DC to 1.4 GHz (nominal) in 2V FSR at 3.2 GS/s DC gain accuracy ± 0.5% (nominal) in 1V FSR ± 0.7% (nominal) in 2V FSR Offset accuracy ± 0.5% in 1V FSR ± 1.5% in 2V FSR Time skew1 Skew between channels2 50 ps (nominal) Channel-to-channel skew stability 3 ± 200 fs pk (nominal) 75 fs RMS (nominal)2 Bandwidth limit filters (BWL) 650 MHz (nominal) for -SR2 Effective number of bits (ENOB) 4 Signal to noise ratio (SNR)4 Spurious free dynamic range (SFDR) Total harmonic distortion (THD) 1. 4 4 -SR2 @ 410 MHz 9.1 (nominal) -SR2 @ 410 MHz 57 dB (nominal) -SR2 @ 410 MHz 64 dBc (nominal) -SR2 @ 410 MHz –64 dB (nominal) The channel-to-channel skew is defined as the magnitude of time delay difference between two digitized channel inputs, granted the same signal is provided to each channel at the exact same time. 2. The measurement represents the maximum time skew between 2 channels of a single unit, measured with a Sinefit method on 100 kSamples, for a sinusoid signal at 400 MHz and averaged 10 times. 3. Skew and offset stability are measured at 25 °C in a climatic chamber. The skew and offset between channels are measured every 5 minutes over 12 hours and after 1 hour stabilization time and the values represent the dispersion of the measurements. 4. Measured for a –1 dBFS input signal in internal clock mode with option -F10 at 1.6 GS/s (option -SR2). 09 | Keysight | M9203A PXIe High-Speed Digitizer/Wideband Digital Receiver - Data Sheet Technical Specifications and Characteristics (continued) Digital conversion Resolution 12 bits Acquisition memory -M02 -M10 -M40 256 MB (64 MSamples/ch) 1 GB (256 MSamples/ch) 4 GB (1 GSamples/ch) Sample clock sources Internal or external Internal clock source Internal, external reference Real-time sampling rates -SR2 -SR2, -INT 1.6 GS/s 3.2 GS/s Sampling jitter 225 fs (nominal)1 Clock accuracy ±15 ppm (nominal) External clock source (CLK IN MMCX connector) Impedance Frequency range 50 Ω (nominal) 2 -SR2 1.8 GHz to 3.2 GHz Signal level +5 dBm to +15 dBm (nominal), 0 V DC Coupling AC External reference clock (REF IN SMB connector) Impedance 50 Ω (nominal) Frequency range 100 MHz ±1 kHz (nominal) Signal level –3 dBm to +3 dBm (nominal) Coupling AC Acquisition modes (depends on firmware options) Single shot, sequence3, continuous 1. Jitter figure based on phase noise integration from 100 Hz to 1600 MHz. 2. The sampling rate corresponds to half of the external clock frequency in 2-channel mode (non interleaved channels). In interleaved mode (only available with the INT option), the sampling rate corresponds to the frequency of the external clock signal. 3. Up to 131072 records. Record maximum length = memory size/number of channels. 10 | Keysight | M9203A PXIe High-Speed Digitizer/Wideband Digital Receiver - Data Sheet Technical Specifications and Characteristics (continued) Trigger Trigger modes Positive or negative edge Trigger sources External, Software, Channel Channel trigger frequency range DC to 250 MHz External trigger (TRG IN SMB connector) Coupling DC Impedance 50 Ω (nominal) Level range ± 5 V (nominal) Minimum amplitude 0.5 V pk-pk Frequency range DC to 2 GHz (nominal) Maximum time stamp duration -SR2 32 days Trigger time interpolator resolution4 6.25 ps (nominal) Trigger time interpolator precision 15 ps RMS (nominal) 4 Rearm time (deadtime) -SR2 Trigger out (TRG OUT SMB connector)1 500 ns (nominal) 1 (programmable), 50 Ω source Signal level 0.8 Vpp ±2.5 Voffset (nominal) into high impedance Control IO (I/O 1 and 2 MMCX connectors)2 Output functions Acquisition active Trigger is armed Trigger accept resynchronization 100 MHz reference clock divided by 23 Sampling clock divided by 323 Low level High level FPGA synchronization Input/output function FPGA programmable I/O 1. 2. 3. 4. At 10 MHz on a 50 Ω load. I/0 3 reserved for future use. Only on I/O 1. At maximum sample rate or at decimated sampling rate down to 1/16 of the highest sample rate (1/32 of the highest sample rate with interleaving). 11 | Keysight | M9203A PXIe High-Speed Digitizer/Wideband Digital Receiver - Data Sheet Technical Specifications and Characteristics (continued) Environmental and physical1 Temperature range Operating 0 to +50 °C (sea-level to 10,000 feet)2 0 to +45 °C (10,000 to 15,000 feet)2 Non-operating –40 to +70 °C Altitude Up to 15,000 feet (4’572 meters) EMC Complies with European EMC Directive – IEC/EN 61326-1 – CISPR Pub 11 Group 1, class A – AS/NZS CISPR 11 – ICES/NMB-001 This ISM device complies with Canadian ICES-001. Cet appareil ISM est conforme à la norme NMB-001 du Canada. Acoustic European Machinery Directive Acoustic noise emission LpA < 70 dB Operator position Normal operation mode Power dissipation + 3.3 V + 12 V Power on PXI connector 3.2 A (typical) 3.5 A (typical) 55 W (typical) Mechanical characteristics Form Factor 3U/2-slot PXI-Express Chassis slot compatibility: PXI Hybrid, PXIe Front panel complies with IEEE1101.10 certification Size Length 185 mm x Width 130 mm x Height 40mm Weight 0.8 kg (1.76 lbs) 1. Samples of this product have been type tested in accordance with the Keysight Environmental Test Manual and verified to be robust against the environmental stresses of Storage, Transportation and End-use; those stresses include but are not limited to temperature, humidity, shock, vibration, altitude and power line conditions. Test Methods are aligned with IEC 60068-2 and levels are similar to MIL-PRF-28800F Class 3. 12 | Keysight | M9203A PXIe High-Speed Digitizer/Wideband Digital Receiver - Data Sheet Technical Specifications and Characteristics (continued) System requirements Topic Windows Linux Operating systems Windows 10 (32-bit and 64-bit), All versions Windows 8.1 (32-bit and 64-bit), All versions Windows 7 SP1 (32-bit and 64-bit). Linux Kernel 2.6 or higher (32 or 64-bit), Debian 7.0, CentOS 6 Processor speed 1 GHz 32-bit (x86), 1 GHz 64-bit (x64), no support for Itanium 64 As per the minimum requirements of the chosen distribution Available memory 1 GB minimum1 Available disk space 2.5 GB available hard disk space, includes: –– 1 GB for Keysight IO Libraries Suite –– 1 GB for Microsoft .NET Framework Note: If using high-speed digitizer applications DVD, Windows 7 (64-bit) is supported. As per the minimum requirements of the chosen distribution 2 100 MB Note: 400 MB for high-speed digitizer applications. Display Minimum of 1024 x 768, 96 or 120 DPI No display required Browser Use a supported version of Internet Explorer; see http://support.microsoft.com/kb/969393 Distribution supplied browser Definitions for specifications Specifications describe the warranted performance of calibrated cards that have been stored for a minimum of 2 hours within the operating temperature range of 0 to 50 °C, unless otherwise stated, and after a 45 minute warm-up period. Data represented in this document are specifications unless otherwise noted. Characteristics describe product performance that is useful in the application of the product, but that is not covered by the product warranty. Characteristics are often referred to as Typical or Nominal values. – Typical describes characteristic performance, which 80% of cards will meet when operated over a 20 to 30 °C temperature range. Typical performance is not warranted. – Nominal describes representative performance that is useful in the application of the product when operated over a 20 to 30 °C temperature range. Nominal performance is not warranted. Note: All graphs contain measured data from several units at room temperature unless otherwise noted. Calibration The M9203A is factory calibrated and shipped with a certificate of calibration. 1. 2. On older PCs with minimum RAM, installation can take a long time when installing the IO Libraries Suite and the .NET Framework. Because of the installation procedure, less disk space may be required for operation than is required for installation. The amount of space listed above is required for installation. The .NET Framework Runtime Components are installed by default with most Windows installations, so you may not need this amount of available disk space. 13 | Keysight | M9203A PXIe High-Speed Digitizer/Wideband Digital Receiver - Data Sheet Configuration and Ordering Information Software information Supported operating systems and host computers Windows 10, 8.1 or 7 (32-bit and 64-bit), All versions Linux Standard compliant drivers IVI-COM, IVI-C, MATLAB Supported application development environments (ADE) VisualStudio (VB.NET, C#, C/C++), VEE, LabVIEW, LabWindows/CVI, MATLAB Ordering information Model Description M9203A PXIe 12-bit PXIe High-Speed Digitizer/Wideband Digital Receiver Includes: -Software examples and product information on CD -MMCX male to BNC male cable, 1m (qty 1) -Warranty extended to 3 years Configurable options Sampling rate Related products Model Description M9018A PXIe 18-slot Chassis M9203A–SR2 1.6 GS/s sampling rate (3.2 GS/s with -INT option) Bandwidth M9203A-F05 650 MHz bandwidth M9203A-F10 Full bandwidth Memory M9021A PCIe Cable Interface M9048A PCIe Deskstop Adapter M9203A-M02 256 MB (64 MS/ch) acquisition memory M9036A PXIe Embedded Controller M9203A-M10 M9037A PXIe High Performance Embedded Controller M9203A-M40 4 GB (1 GS/ch) acquisition memory M9393A PXIe Performance Vector Signal Analyzer: 50 GHz M9362AD01 PXIe Quad Downconverter: 10 MHz to 50 GHz M9203A-DGT Digitizer firmware 89601B 89600 VSA software, transportable license M9203A-INT Interleaved channel sampling functionality U5340A FPGA Development Kit for High-Speed Digitizers M9203A-FDK Custom firmware capability M9203A-TSR Triggered simultaneous acquisition and readout M9203A-DDC Wideband real-time digital down-conversion Accessories 1 GB (256 MS/ch) acquisition memory Firmware Applications Model Description M9203A-CB0 Digitizer streaming and recording U5300A-102 MMCX male to BNC male cable, 1 m M9203A-CB2 Digital down-converter streaming at 1.6 GS/s U5300A-112 SMB female to BNC male cable, 0.1 m M9203A-BB1 High fidelity digitizer These options represent the standard configuration Please contact Keysight for other options not shown: [email protected] Advantage services: calibration and warranty Keysight Advantage Services is committed to your success throughout your equipment’s lifetime. M9203A-A6J Commercial calibration certificate with test data Included Return-to-Keysight warranty – 3 years R-51B-001-5Z Return-to-Keysight warranty – 5 years 14 | Keysight | M9203A PXIe High-Speed Digitizer/Wideband Digital Receiver - Data Sheet Evolving Since 1939 Our unique combination of hardware, software, services, and people can help you reach your next breakthrough. We are unlocking the future of technology. From Hewlett-Packard to Agilent to Keysight. myKeysight www.keysight.com/find/mykeysight A personalized view into the information most relevant to you. http://www.keysight.com/find/emt_product_registration Register your products to get up-to-date product information and find warranty information. Keysight Services www.keysight.com/find/service Keysight Services can help from acquisition to renewal across your instrument’s lifecycle. Our comprehensive service offerings—onestop calibration, repair, asset management, technology refresh, consulting, training and more—helps you improve product quality and lower costs. Keysight Assurance Plans www.keysight.com/find/AssurancePlans Up to ten years of protection and no budgetary surprises to ensure your instruments are operating to specification, so you can rely on accurate measurements. Keysight Channel Partners www.keysight.com/find/channelpartners Get the best of both worlds: Keysight’s measurement expertise and product breadth, combined with channel partner convenience. www.keysight.com/find/high-speed-digitizers www.keysight.com/find/M9203A For more information on Keysight Technologies’ products, applications or services, please contact your local Keysight office. The complete list is available at: www.keysight.com/find/contactus Americas Canada Brazil Mexico United States (877) 894 4414 55 11 3351 7010 001 800 254 2440 (800) 829 4444 Asia Pacific Australia China Hong Kong India Japan Korea Malaysia Singapore Taiwan Other AP Countries 1 800 629 485 800 810 0189 800 938 693 1 800 11 2626 0120 (421) 345 080 769 0800 1 800 888 848 1 800 375 8100 0800 047 866 (65) 6375 8100 Europe & Middle East Austria Belgium Finland France Germany Ireland Israel Italy Luxembourg Netherlands Russia Spain Sweden Switzerland United Kingdom 0800 001122 0800 58580 0800 523252 0805 980333 0800 6270999 1800 832700 1 809 343051 800 599100 +32 800 58580 0800 0233200 8800 5009286 800 000154 0200 882255 0800 805353 Opt. 1 (DE) Opt. 2 (FR) Opt. 3 (IT) 0800 0260637 For other unlisted countries: www.keysight.com/find/contactus (BP-9-7-17) DEKRA Certified ISO9001 Quality Management System www.keysight.com/go/quality Keysight Technologies, Inc. DEKRA Certified ISO 9001:2015 Quality Management System This information is subject to change without notice. © Keysight Technologies, 2016-2018 Published in USA, February 27, 2018 5992-1474EN www.keysight.com