LP2985LV-N www.ti.com SNOS510P – NOVEMBER 1999 – REVISED APRIL 2013 LP2985LV-N Micropower 150 mA Low-Noise Low-Dropout Regulator in SOT-23 and DSBGA packages for Applications with Output Voltages ≤ 2.0V Designed for Use with Very Low ESR Output Capacitors Check for Samples: LP2985LV-N FEATURES DESCRIPTION • • • • • • • • • • • • • The LP2985LV-N is a 150 mA, fixed-output voltage regulator designed to provide high performance and low noise in applications requiring output voltages ≤ 2.0V. 1 2 Ensured 150 mA Output Current Smallest Possible Size (DSBGA) Requires Minimum External Components Stable With Low-ESR Output Capacitor <1 µA Quiescent Current When Shut Down Low Ground Pin Current at all Loads Output Voltage Accuracy 1% (A Grade) High Peak Current Capability Wide Supply Voltage Range (16V Max) Low ZOUT: 0.3Ω Typical (10 Hz to 1 MHz) Overtemperature/Overcurrent Protection −40°C to +125°C Junction Temperature Range Custom Voltages Available APPLICATIONS • • • • Cellular Phone Palmtop/Laptop Computer Personal Digital Assistant (PDA) Camcorder, Personal Stereo, Camera Using an optimized VIP (Vertically Integrated PNP) process, the LP2985LV-N delivers unequaled performance in all specifications critical to batterypowered designs: Ground Pin Current: Typically 825 µA @ 150 mA load, and 75 µA @ 1 mA load. Enhanced Stability: The LP2985LV-N is stable with output capacitor ESR as low as 5 mΩ, which allows the use of ceramic capacitors on the output. Sleep Mode: Less than 1 µA quiescent current when ON/OFF pin is pulled low. Smallest Possible Size: DSBGA package uses absolute minimum board space. Precision Output: 1% tolerance output voltages available (A grade). Low Noise: By adding a 10 nF bypass capacitor, output noise can be reduced to 30 µV (typical). Block Diagram Figure 1. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 1999–2013, Texas Instruments Incorporated LP2985LV-N SNOS510P – NOVEMBER 1999 – REVISED APRIL 2013 www.ti.com Basic Application Circuit *ON/OFF input must be actively terminated. Tie to VIN if this function is not to be used. **Minimum capacitance is shown to ensure stability (may be increased without limit). Ceramic capacitor required for output (see APPLICATION HINTS). ***Reduces output noise (may be omitted if application is not noise critical). Use ceramic or film type with very low leakage current (see APPLICATION HINTS). Figure 2. Connection Diagram Note: The actual physical placement of the package marking will vary from part to part. Package marking contains date code and lot traceability information, and will vary considerably. Package marking does not correlate to device type. Top View Top View Figure 3. 5-Lead SOT-23 Package See Package Number DBV0005A Figure 4. 5 Bump DSBGA Package See Package Number YPB0005 PIN DESCRIPTIONS Name Pin Number SOT-23 DSBGA Function VIN 1 C3 Input Voltage GND 2 A1 Common Ground (device substrate) ON/OFF 3 A3 Logic high enable input BYPASS 4 B2 Bypass capacitor for low noise operation VOUT 5 C1 Regulated output voltage These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 2 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated Product Folder Links: LP2985LV-N LP2985LV-N www.ti.com SNOS510P – NOVEMBER 1999 – REVISED APRIL 2013 ABSOLUTE MAXIMUM RATINGS (1) (2) Storage Temperature Range −65°C to +150°C Operating Junction Temperature Range −40°C to +125°C Lead Temp. (Soldering, 5 sec.) 260°C ESD Rating (3) Power Dissipation 2 kV (4) Internally Limited −0.3V to +16V Input Supply Voltage (Survival) Input Supply Voltage (Operating) 2.2V to +16V −0.3V to +16V Shutdown Input Voltage (Survival) Output Voltage (Survival (5)) −0.3V to +9V IOUT (Survival) Short Circuit Protected Input-Output Voltage (Survival (6)) (1) (2) (3) (4) (5) (6) −0.3V to +16V Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Electrical specifications do not apply when operating the device outside of its rated operating conditions. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. The ESD rating of pins 3 and 4 for the SOT-23 package, or pins 5 and 2 for the DSBGA package, is 1 kV. The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junction-to-ambient thermal resistance, θJ-A, and the ambient temperature, TA. The maximum allowable power dissipation at any ambient temperture is calculated using: Where the value of θJ-A for the SOT-23 package is 220°C/W in a typical PC board mounting. Exceeding the maximum allowable dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. If used in a dual-supply system where the regulator load is returned to a negative supply, the LP2985LV-N output must be diodeclamped to ground. The output PNP structure contains a diode between the VIN to VOUT terminals that is normally reverse-biased. Reversing the polarity from VIN to VOUT will turn on this diode, and possibly damage the device (See APPLICATION HINTS). Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated Product Folder Links: LP2985LV-N 3 LP2985LV-N SNOS510P – NOVEMBER 1999 – REVISED APRIL 2013 www.ti.com ELECTRICAL CHARACTERISTICS (1) Limits in standard typeface are for TJ = 25°C. and limits in boldface type apply over the full operating temperature range. Unless otherwise specified: VIN = VO(NOM) + 1V, IL = 1 mA, CIN = 1 µF, COUT = 4.7 µF, VON/OFF = 2V. Symbol Parameter Output Voltage Tolerance ΔVO Output Voltage Line Regulation IGND Conditions Typ LP2985AI-X.X (2) Min Max Min Max IL = 1 mA −1.0 1.0 −1.5 1.5 1 mA ≤ IL ≤ 50 mA −1.5 −2.5 1.5 2.5 −2.5 −3.5 2.5 3.5 1 mA ≤ IL ≤ 150 mA −2.5 −3.5 2.5 3.5 −3.0 −4.0 3.0 4.0 VO(NOM)+1V ≤ VIN ≤ 16V 0.007 VIN - VOUT 0.014 0.032 65 95 125 95 125 IL = 1 mA 75 110 170 110 170 IL = 10 mA 120 220 400 220 400 IL = 50 mA 300 500 900 500 900 IL = 150 mA 825 1200 2000 1200 2000 VON/OFF < 0.3V 0.01 0.8 0.8 VON/OFF < 0.15V 0.05 2 2 2.05 2.20 2.20 IL = 50mA 120 150 250 150 250 IL = 150mA 280 350 600 350 600 Minimum Input Voltage Required To maintain Output Regulation (3) Dropout Voltage 0.014 0.032 IL = 0 Ground Pin Current VIN(min) LP2985I-X.X (2) (3) %/V µA V mV 1.4 Low = O/P OFF 0.55 0.15 0.15 VON/OFF = 0 0.01 −2 −2 VON/OFF = 5V 5 15 15 Output Noise Voltage (RMS) BW = 300 Hz to 50 kHz, COUT = 10 µF CBYPASS = 10 nF VOUT = 1.8V 30 µV Ripple Rejection f = 1 kHz, CBYPASS = 10 nF COUT = 10 µF 45 dB IO(SC) Short Circuit Current RL = 0 (Steady State) (5) 400 mA IO(PK) Peak Output Current VOUT ≥ Vo(NOM) −5% 350 mA ON/OFF Input Voltage (4) ION/OFF ON/OFF Input Current en (1) (2) (3) (4) (5) 4 1.6 %VNOM High = O/P ON VON/OFF 1.6 Units V µA Exposing the DSBGA device to direct sunlight will cause misoperation. See APPLICATION HINTS for additional information. Limits are 100% production tested at 25°C. Limits over the operating temperature range are ensured through correlation using Statistical Quality Control (SQC) methods. The limits are used to calculate Average Outgoing Quality Level (AOQL). VIN must be the greater of 2.2V or VOUT(NOM) + Dropout Voltage to maintain output regulation. Dropout Voltage is defined as the input to output differential at which the output voltage drops 2% below ther value measured with a 1V differential. The ON/OFF input must be properly driven to prevent possible misoperation. For details, refer to APPLICATION HINTS. The LP2985LV-N has foldback current limiting which allows a high peak current when VOUT > 0.5V, and then reduces the maximum output current as VOUT is forced to ground (see TYPICAL PERFORMANCE CHARACTERISTICS curves). Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated Product Folder Links: LP2985LV-N LP2985LV-N www.ti.com SNOS510P – NOVEMBER 1999 – REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS Unless otherwise specified: CIN = 1µF, COUT = 4.7µF, VIN = VOUT(NOM) +1, VOUT = 1.8V, TA = 25°C, ON/OFF pin is tied to VIN VOUT vs Temperature Short-Circuit Current Figure 5. Figure 6. Short-Circuit Current Short-Circuit Current vs Output Voltage Figure 7. Figure 8. Ripple Rejection COUT = 4.7µF, Bypass = 10nF Ripple Rejection COUT = 4.7µF, No Bypass Figure 9. Figure 10. Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated Product Folder Links: LP2985LV-N 5 LP2985LV-N SNOS510P – NOVEMBER 1999 – REVISED APRIL 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS (continued) Unless otherwise specified: CIN = 1µF, COUT = 4.7µF, VIN = VOUT(NOM) +1, VOUT = 1.8V, TA = 25°C, ON/OFF pin is tied to VIN 6 Output Impedance vs Frequency Output Impedance vs Frequency Figure 11. Figure 12. Noise Density Noise Density Figure 13. Figure 14. Ground Pin vs Load Current Minimum Input Voltage vs Temperature Figure 15. Figure 16. Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated Product Folder Links: LP2985LV-N LP2985LV-N www.ti.com SNOS510P – NOVEMBER 1999 – REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS (continued) Unless otherwise specified: CIN = 1µF, COUT = 4.7µF, VIN = VOUT(NOM) +1, VOUT = 1.8V, TA = 25°C, ON/OFF pin is tied to VIN Minimum Input Voltage vs Temperature Input Current vs VIN Figure 17. Figure 18. Input Current vs VIN Input Current vs VIN Figure 19. Figure 20. Ground Pin Current vs Temperature Instantaneous Short Circuit Current Figure 21. Figure 22. Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated Product Folder Links: LP2985LV-N 7 LP2985LV-N SNOS510P – NOVEMBER 1999 – REVISED APRIL 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS (continued) Unless otherwise specified: CIN = 1µF, COUT = 4.7µF, VIN = VOUT(NOM) +1, VOUT = 1.8V, TA = 25°C, ON/OFF pin is tied to VIN 8 Output Characteristics Load Transient Figure 23. Figure 24. Load Transient Load Transient Figure 25. Figure 26. Line Transient Line Transient Figure 27. Figure 28. Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated Product Folder Links: LP2985LV-N LP2985LV-N www.ti.com SNOS510P – NOVEMBER 1999 – REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS (continued) Unless otherwise specified: CIN = 1µF, COUT = 4.7µF, VIN = VOUT(NOM) +1, VOUT = 1.8V, TA = 25°C, ON/OFF pin is tied to VIN Line Transient Line Transient Figure 29. Figure 30. Turn-On Time Turn-On Time Figure 31. Figure 32. Turn-On Time Turn-On Time Figure 33. Figure 34. Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated Product Folder Links: LP2985LV-N 9 LP2985LV-N SNOS510P – NOVEMBER 1999 – REVISED APRIL 2013 www.ti.com APPLICATION HINTS EXTERNAL CAPACITORS Like any low-dropout regulator, the LP2985LV-N requires external capacitors for regulator stability. These capacitors must be correctly selected for good performance. Input Capacitor An input capacitor whose capacitance is ≥ 1 µF is required between the LP2985LV-N input and ground (the amount of capacitance may be increased without limit). This capacitor must be located a distance of not more than 1 cm from the input pin and returned to a clean analog ground. Any good quality ceramic, tantalum, or film capacitor may be used at the input. Important: Tantalum capacitors can suffer catastrophic failure due to surge current when connected to a lowimpedance source of power (like a battery or very large capacitor). If a Tantalum capacitor is used at the input, it must be ensured by the manufacturer to have a surge current rating sufficient for the application. There are no requirements for ESR on the input capacitor, but tolerance and temperature coefficient must be considered when selecting the capacitor to ensure the capacitance will be ≥ 1 µF over the entire operating temperature range. Output Capacitor The LP2985LV-N is designed specifically to work with ceramic output capacitors, utilizing circuitry which allows the regulator to be stable across the entire range of output current with an output capacitor whose ESR is as low as 5 mΩ. It may also be possible to use Tantalum or film capacitors at the output, but these are not as attractive for reasons of size and cost (see CAPACITOR CHARACTERISTICS section). The output capacitor must meet the requirement for minimum amount of capacitance and also have an ESR (equivalent series resistance) value which is within the stable range. Curves are provided which show the stable ESR range as a function of load current (see ESR graphs Figure 35 and Figure 36). Figure 35. LP2985LV-N 2.2µF Stable ESR Range Figure 36. LP2985LV-N 4.7µF Stable ESR Range Important: The output capacitor must maintain its ESR within the stable region over the full operating temperature range of the application to assure stability. The LP2985LV-N requires a minimum of 2.2 µF on the output (output capacitor size can be increased without limit). It is important to remember that capacitor tolerance and variation with temperature must be taken into consideration when selecting an output capacitor so that the minimum required amount of output capacitance is provided over the full operating temperature range. It should be noted that ceramic capacitors can exhibit large changes in capacitance with temperature (see CAPACITOR CHARACTERISTICS section). The output capacitor must be located not more than 1 cm from the output pin and returned to a clean analog ground. 10 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated Product Folder Links: LP2985LV-N LP2985LV-N www.ti.com SNOS510P – NOVEMBER 1999 – REVISED APRIL 2013 Noise Bypass Capacitor Connecting a 10 nF capacitor to the Bypass pin significantly reduces noise on the regulator output. It should be noted that the capacitor is connected directly to a high-impedance circuit in the bandgap reference. Because this circuit has only a few microamperes flowing in it, any significant loading on this node will cause a change in the regulated output voltage. For this reason, DC leakage current through the noise bypass capacitor must never exceed 100 nA, and should be kept as low as possible for best output voltage accuracy. The types of capacitors best suited for the noise bypass capacitor are ceramic and film. High-quality ceramic capacitors with either NPO or COG dielectric typically have very low leakage. 10 nF polypropolene and polycarbonate film capacitors are available in small surface-mount packages and typically have extremely low leakage current. CAPACITOR CHARACTERISTICS The LP2985LV-N was designed to work with ceramic capacitors on the output to take advantage of the benefits they offer: for capacitance values in the 2.2 µF to 4.7 µF range, ceramics are the least expensive and also have the lowest ESR values (which makes them best for eliminating high-frequency noise). The ESR of a typical 2.2 µF ceramic capacitor is in the range of 10 mΩ to 20 mΩ, which easily meets the ESR limits required for stability by the LP2985LV-N. One disadvantage of ceramic capacitors is that their capacitance can vary with temperature. Most large value ceramic capacitors (≥ 2.2 µF) are manufactured with the Z5U or Y5V temperature characteristic, which results in the capacitance dropping by more than 50% as the temperature goes from 25°C to 85°C. This could cause problems if a 2.2 µF capacitor were used on the output since it will drop down to approximately 1 µF at high ambient temperatures (which could cause the LP2985LV-N to oscillate). If Z5U or Y5V capacitors are used on the output, a minimum capacitance value of 4.7 µF must be observed. A better choice for temperature coefficient in ceramic capacitors is X7R, which holds the capacitance within ±15%. Unfortunately, the larger values of capacitance are not offered by all manufacturers in the X7R dielectric. Tantalum Tantalum capacitors are less desirable than ceramics for use as output capacitors because they are more expensive when comparing equivalent capacitance and voltage ratings in the 1 µF to 4.7 µF range. Another important consideration is that Tantalum capacitors have higher ESR values than equivalent size ceramics. This means that while it may be possible to find a Tantalum capacitor with an ESR value within the stable range, it would have to be larger in capacitance (which means bigger and more costly) than a ceramic capacitor with the same ESR value. It should also be noted that the ESR of a typical Tantalum will increase about 2:1 as the temperature goes from 25°C down to −40°C, so some guard band must be allowed. On/Off Input Operation The LP2985LV-N is shut off by driving the ON/OFF input low, and turned on by pulling it high. If this feature is not to be used, the ON/OFF input should be tied to VIN to keep the regulator output on at all times. To assure proper operation, the signal source used to drive the ON/OFF input must be able to swing above and below the specified turn-on/turn-off voltage thresholds listed in the ELECTRICAL CHARACTERISTICS (1) section under VON/OFF. To prevent mis-operation, the turn-on (and turn-off) voltage signals applied to the ON/OFF input must have a slew rate which is ≥ 40 mV/µs. CAUTION The regulator output voltage cannot be ensured if a slow-moving AC (or DC) signal is applied that is in the range between the specified turn-on and turn-off voltages listed under the electrical specification VON/OFF (see Electrical Characteristics). (1) Exposing the DSBGA device to direct sunlight will cause misoperation. See APPLICATION HINTS for additional information. Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated Product Folder Links: LP2985LV-N 11 LP2985LV-N SNOS510P – NOVEMBER 1999 – REVISED APRIL 2013 www.ti.com REVERSE INPUT-OUTPUT VOLTAGE The PNP power transistor used as the pass element in the LP2985LV-N has an inherent diode connected between the regulator output and input. During normal operation (where the input voltage is higher than the output) this diode is reverse-biased. VIN VOUT PNP GND Figure 37. Normal Operation However, if the output is pulled above the input, this diode will turn ON and current will flow into the regulator output. In such cases, a parasitic SCR can latch which will allow a high current to flow into VIN (and out the ground pin), which can damage the part. In any application where the output may be pulled above the input, an external Schottky diode must be connected from VIN to VOUT (cathode on VIN, anode on VOUT), to limit the reverse voltage across the LP2985LV-N to 0.3V (see ABSOLUTE MAXIMUM RATINGS). SCHOTTKY DIODE VIN VOUT PNP GND Figure 38. Operation with Schottky Diode DSBGA MOUNTING The DSBGA package requires specific mounting techniques which are detailed in Texas Instruments Application Note AN-1112. Referring to the section Surface Mount Technology (SMT) Assembly Considerations, it should be noted that the pad style which must be used with the 5-pin package is the NSMD (non-solder mask defined) type. For best results during assembly, alignment ordinals on the PC board may be used to facilitate placement of the DSBGA device. DSBGA LIGHT SENSITIVITY Exposing the DSBGA device to direct sunlight will cause misoperation of the device. Light sources such as Halogen lamps can also affect electrical performance if brought near to the device. The wavelengths which have the most detrimental effect are reds and infra-reds, which means that the fluorescent lighting used inside most buildings has very little effect on performance. A DSBGA test board was brought to within 1 cm of a fluorescent desk lamp and the effect on the regulated output voltage was negligible, showing a deviation of less than 0.1% from nominal. 12 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated Product Folder Links: LP2985LV-N LP2985LV-N www.ti.com SNOS510P – NOVEMBER 1999 – REVISED APRIL 2013 REVISION HISTORY Changes from Revision O (April 2013) to Revision P • Page Changed layout of National Data Sheet to TI format .......................................................................................................... 12 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated Product Folder Links: LP2985LV-N 13 PACKAGE OPTION ADDENDUM www.ti.com 16-Oct-2015 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) LP2985AIM5-1.5/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LCHA LP2985AIM5-1.8/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LAYA LP2985AIM5-2.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LCDA LP2985AIM5X-1.8/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LAYA LP2985AIM5X-2.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LCDA LP2985AITP-1.8/NOPB LIFEBUY DSBGA YPB 5 250 Green (RoHS & no Sb/Br) SNAGCU Level-1-260C-UNLIM -40 to 125 5 LP2985AITPX-1.8/NOPB LIFEBUY DSBGA YPB 5 3000 Green (RoHS & no Sb/Br) SNAGCU Level-1-260C-UNLIM -40 to 125 5 LP2985IM5-1.8 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 LAYB LP2985IM5-1.8/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LAYB LP2985IM5-2.0 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 LCDB LP2985IM5-2.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LCDB LP2985IM5X-1.8/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LAYB LP2985IM5X-2.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LCDB (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 16-Oct-2015 Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 2-Sep-2015 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ LP2985AIM5-1.5/NOPB SOT-23 DBV 5 1000 178.0 8.4 LP2985AIM5-1.8/NOPB SOT-23 DBV 5 1000 178.0 LP2985AIM5-2.0/NOPB SOT-23 DBV 5 1000 178.0 LP2985AIM5X-1.8/NOPB SOT-23 DBV 5 3000 LP2985AIM5X-2.0/NOPB SOT-23 DBV 5 DSBGA YPB LP2985AITPX-1.8/NOPB DSBGA YPB LP2985AITP-1.8/NOPB Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 3.2 3.2 1.4 4.0 8.0 Q3 8.4 3.2 3.2 1.4 4.0 8.0 Q3 8.4 3.2 3.2 1.4 4.0 8.0 Q3 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 5 250 178.0 8.4 1.02 1.19 0.66 4.0 8.0 Q1 5 3000 178.0 8.4 1.02 1.19 0.66 4.0 8.0 Q1 LP2985IM5-1.8 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5-1.8/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5-2.0 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5-2.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5X-1.8/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2985IM5X-2.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 2-Sep-2015 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LP2985AIM5-1.5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985AIM5-1.8/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985AIM5-2.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985AIM5X-1.8/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2985AIM5X-2.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2985AITP-1.8/NOPB DSBGA YPB 5 250 210.0 185.0 35.0 LP2985AITPX-1.8/NOPB DSBGA YPB 5 3000 210.0 185.0 35.0 LP2985IM5-1.8 SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985IM5-1.8/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985IM5-2.0 SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985IM5-2.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2985IM5X-1.8/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2985IM5X-2.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 Pack Materials-Page 2 MECHANICAL DATA YPB0005 D 0.5±0.045 E TPA05XXX (Rev C) D: Max = 1.159 mm, Min =1.098 mm E: Max = 0.981 mm, Min = 0.92 mm 4215098/A NOTES: A. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994. B. This drawing is subject to change without notice. www.ti.com 12/12 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2016, Texas Instruments Incorporated