iW1696 Low-Power Off-line Digital Green-Mode PWM Controller 1.0 Features 2.0 Description ●● Primary-side feedback eliminates opto-isolators and simplifies design ●● Adaptive multi-mode PWM/PFM control improves efficiency ●● Quasi-resonant operation for highest overall efficiency ●● EZ-EMI ® design to easily meet global EMI standards ●● Direct drive of low-cost BJT switch ●● Dynamic base current control ●● Very tight constant voltage and constant current regulation with primary-side-only feedback ●● No external compensation components required ●● Complies with EPA 2.0 energy-efficiency specifications with ample margin ●● Able to meet < 30 mW no load power consumption ●● Low start-up current (10 μA typical) ●● Built-in soft start ●● Built-in short circuit protection and output overvoltage protection ●● Built-in current sense resistor short protection The iW1696 is a high performance AC/DC power supply controller which uses digital control technology to build peak current mode PWM flyback power supplies. The device directly drives a power BJT and operates in quasi-resonant mode to provide high efficiency along with a number of key built-in protection features while minimizing the external component count, simplifying EMI design and lowering the total bill of material cost. The iW1696 removes the need for secondary feedback circuitry while achieving excellent line and load regulation. It also eliminates the need for loop compensation components while maintaining stability overall operating conditions. Pulse-by-pulse waveform analysis allows for a loop response that is much faster than traditional solutions, resulting in improved dynamic load response. The built-in power limit function enables optimized transformer design in universal off-line applications and allows for a wide input voltage range. The ultra-low start-up power and operating current at light load ensure that the iW1696 is ideal for applications targeting the newest regulatory standards for average efficiency. 3.0 Applications ●● Low power AC/DC adapter/chargers for cell phones, PDAs, digital still cameras ●● No audible noise over entire operation range ●● Linear AC/DC replacement L + + N VOUT GND U1 iW1696 1 VCC 2 GND 3 VSENSE OUTPUT 5 ISENSE 4 Figure 3.1: iW1696 Typical Application Circuit Rev. 2.0 iW1696 February 13, 2012 Page 1 iW1696 Low-Power Off-line Digital Green-Mode PWM Controller 4.0 Pinout Description iW1696 Pin # Name Type 1 VCC Power Input 2 GND Ground 3 VSENSE 4 ISENSE 5 OUTPUT 1 VCC 2 GND 3 VSENSE OUTPUT 5 ISENSE 4 Pin Description Power supply for control logic. Ground. Analog Input Auxiliary voltage sense (used for primary regulation). Analog Input Primary current sense. Used for cycle-by-cycle peak current control and limit. Output Base drive for BJT. 5.0 Absolute Maximum Ratings Absolute maximum ratings are the parameter values or ranges which can cause permanent damage if exceeded. For maximum safe operating conditions, refer to Electrical Characteristics in Section 6.0. Parameter Symbol Value Units DC supply voltage range (pin 1, ICC = 20mA max) VCC -0.3 to 18 V Continuous DC supply current at VCC pin (VCC = 15 V) ICC 20 mA Output (pin 5) -0.3 to 4.0 V VSENSE input (pin 3, IVsense ≤ 10 mA) -0.7 to 4.0 V ISENSE input (pin 4) -0.3 to 4.0 V TJ MAX 125 °C Storage temperature TSTG –65 to 150 °C Lead temperature during IR reflow for ≤ 15 seconds TLEAD 260 °C θJA 190 °C/W ESD rating per JEDEC JESD22-A114 2,000 V Latch-Up test per JEDEC 78 ±100 mA Maximum junction temperature Thermal Resistance Junction-to-Ambient Rev. 2.0 iW1696 February 13, 2012 Page 2 iW1696 Low-Power Off-line Digital Green-Mode PWM Controller 6.0 Electrical Characteristics VCC = 12 V, -40°C ≤ TA ≤ +85°C, unless otherwise specified (Note 1) Parameter Symbol Test Conditions Min Typ Max Unit 1 μA 1.553 V VSENSE SECTION (Pin 3) Input leakage current IBVS VSENSE = 2 V Nominal voltage threshold VSENSE(NOM) TA=25°C, negative edge 1.523 1.538 Output OVP threshold -00 VSENSE(MAX) TA=25°C, negative edge 1.834 V Output OVP threshold -01 (Note 2) VSENSE(MAX) TA=25°C, negative edge Load = 100 % 1.926 V Output OVP threshold -03 (Note 2) VSENSE(MAX) TA=25°C, negative edge Load = 100 % 1.972 V Output OVP threshold -04 (Note 2) VSENSE(MAX) TA=25°C, negative edge Load = 100 % 1.880 V ISENSE SECTION (Pin 4) VOCP 1.1 ISENSE regulation upper limit (Note 2) VIPK(HIGH) 1.0 V ISENSE regulation lower limit (Note 2) VIPK(LOW) 0.25 V Overcurrent threshold Input leakage current ILK ISENSE = 1.0 V 1.15 V 1 μA 6.0 W OUTPUT SECTION (Pin 5) Output low level ON-resistance Switching frequency (Note 3) RDS(ON)LO ISINK = 5 mA 3 fSW > 50% load 40 kHz VCC SECTION (Pin 1) Maximum operating voltage (Note 2) VCC(MAX) Start-up threshold VCC(ST) VCC rising 11 Undervoltage lockout threshold VCC(UVL) VCC falling 5.2 Start-up Current IIN(ST) VCC = 10 V Quiescent current ICCQ No IB current Zener breakdown voltage VZB Zener current = 1 mA TA=25°C 18 16 V 12 13 V 5.5 5.8 V 8 15 μA 2.5 3.5 mA 19 20.5 V Notes: Note 1. Adjust VCC above the start-up threshold (VCC(ST)) before setting at 12 V. Note 2. These parameters are not 100% tested, guaranteed by design and characterization. Note 3. Operating frequency varies based on the load conditions, see Theory of Operation for more details. Rev. 2.0 iW1696 February 13, 2012 Page 3 iW1696 Low-Power Off-line Digital Green-Mode PWM Controller 7.0 Typical Performance Characteristics 12.20 VCC Start-up Threshold (V) 5.58 VCC UVLO (V) 5.54 5.50 5.46 5.42 5.38 -50 -25 0 25 50 75 100 125 Ambient Temperature (ºC) Figure 7.1 : VCC UVLO vs. Temperature 11.90 11.80 -25 0 25 50 75 100 Ambient Temperature (ºC) 125 150 Figure 7.2 : Start-Up Threshold vs. Temperature 2.010 Internal Reference Voltage (V) fsw @ Load > 50% (kHz) 12.00 11.70 -50 150 44 42 40 38 36 34 -50 -25 0 25 50 75 100 Ambient Temperature (ºC) 125 150 Figure 7.3 : Switching Frequency vs. Temperature1 VCC Supply Start-up Current (µA) 12.10 2.006 2.002 1.998 1.994 1.990 -50 -25 0 25 50 75 100 Ambient Temperature (ºC) 125 150 Figure 7.4 : Internal Reference vs. Temperature 10.0 8.0 6.0 4.0 2.0 0.0 0.0 3.5 7.0 VCC (V) 10.5 14.0 Figure 7.5 : VCC vs. VCC Supply Start-up Current Notes: Note 1. Operating frequency varies based on the load conditions, see Theory of Operation for more details. Rev. 2.0 iW1696 February 13, 2012 Page 4 iW1696 Low-Power Off-line Digital Green-Mode PWM Controller 8.0 Functional Block Diagram 1 VCC Start-up Enable VSENSE 3 Signal Conditioning BJT Base Drive Digital Logic Control VFB 5 Output OCP GND 2 VSENSE(NOM) = 1.538 V DAC IPK 1.1 V 4 ISENSE VIPK Figure 8.1: iW1696 Functional Block Diagram 9.0 Theory of Operation The iW1696 is a digital controller which uses a new, proprietary primary-side control technology to eliminate the opto-isolated feedback and secondary regulation circuits required in traditional designs. This results in a low-cost solution for low power AC/DC adapters. The core PWM processor uses fixed-frequency Discontinuous Conduction Mode (DCM) operation at higher power levels and switches to variable frequency operation at light loads to maximize efficiency. Furthermore, iWatt’s digital control technology enables fast dynamic response, tight output regulation, and full featured circuit protection with primary-side control. Referring to the block diagram in Figure 8.1, the digital logic control block generates the switching on-time and off-time information based on the output voltage and current feedback signal and provides commands to dynamically control the external BJT base current. The system loop is automatically compensated internally by a digital error amplifier. Adequate system phase margin and gain margin are guaranteed by design and no external analog components are required for loop compensation. The iW1696 uses an advanced digital control algorithm to reduce system design time and increase reliability. Rev. 2.0 Furthermore, accurate secondary constant-current operation is achieved without the need for any secondary-side sense and control circuits. The iW1696 uses adaptive multi-mode PWM/PFM control to dynamically change the BJT switching frequency for efficiency, EMI, and power consumption optimization. In addition, it achieves unique BJT quasi-resonant switching to further improve efficiency and reduce EMI. Built-in protection features include overvoltage protection (OVP), output short circuit protection (SCP), over current protection (OCP), single pin fault protection and ISENSE fault detection. iWatt’s digital control scheme is specifically designed to address the challenges and trade-offs of power conversion design. This innovative technology is ideal for balancing new regulatory requirements for green mode operation with more practical design considerations such as lowest possible cost, smallest size and high performance output control. iW1696 February 13, 2012 Page 5 iW1696 Low-Power Off-line Digital Green-Mode PWM Controller 9.1 Pin Detail Start-up Sequencing Pin 1 – VCC VCC(ST) Power supply for the controller during normal operation. The controller will start up when VCC reaches 12 V (typical) and will shut-down when the VCC voltage is 5.5 V (typical). A decoupling capacitor should be connected between the VCC pin and GND. Pin 2 – GND VCC ENABLE Ground. Pin 3 – VSENSE Sense signal input from auxiliary winding. This provides the secondary voltage feedback used for output regulation. Pin 4 – ISENSE Primary current sense. Used for cycle-by-cycle peak current control and limit. Pin 5 – OUTPUT Base drive for the external power BJT switch. Figure 9.1: Start-up Sequencing Diagram 9.3 Understanding Primary Feedback Figure 9.2 illustrates a simplified flyback converter. When the switch Q1 conducts during tON(t), the current ig(t) is directly drawn from rectified sinusoid vg(t). The energy Eg(t) is stored in the magnetizing inductance LM. The rectifying diode D1 is reverse biased and the load current IO is supplied by the secondary capacitor CO. When Q1 turns off, D1 conducts and the stored energy Eg(t) is delivered to the output. iin(t) 9.2 Start-up Prior to start-up, the Vcc pin is charged typically through startup resistors. When VCC bypass capacitor is fully charged to a voltage higher than the start-up threshold VCC(ST), the ENABLE signal becomes active to enable the control logic, and the iW1696 commences soft start function. An adaptive soft-start control algorithm is applied at startup state, during which the initial output pulses will be small and gradually get larger until the full pulse width is achieved. The peak current is limited cycle by cycle by the IPEAK comparator. If at any time the VCC voltage drops below VCC(UVL) threshold then all the digital logic is reset. At this time ENABLE signal becomes low and the VCC capacitor is charged up again towards the start-up threshold. + ig(t) id(t) N:1 D1 vg(t) vin(t) VO + CO IO VAUX – TS(t) Q1 Figure 9.2: Simplified Flyback Converter In order to tightly regulate the output voltage, the information about the output voltage and load current need to be accurately sensed. In the DCM flyback converter, this information can be read via the auxiliary winding or the primary magnetizing inductance (LM). During the Q1 on-time, the load current is supplied from the output filter capacitor CO. The voltage across LM is vg(t), assuming the voltage dropped across Q1 is zero. The current in Q1 ramps up linearly at a rate of: dig ( t ) dt = vg ( t ) LM (9.1) At the end of on-time, the current has ramped up to: Rev. 2.0 iW1696 February 13, 2012 Page 6 iW1696 Low-Power Off-line Digital Green-Mode PWM Controller vg ( t ) × tON LM (9.2) This current represents a stored energy of: 9.4 Constant Voltage Operation LM 2 × ig _ peak ( t ) 2 (9.3) When Q1, turns off at tO, ig(t) in LM forces a reversal of polarities on all windings. Ignoring the communication-time caused by the leakage inductance LK at the instant of turn-off tO, the primary current transfers to the secondary at a peak amplitude of: id = (t ) NP × ig _ peak ( t ) NS (9.4) Assuming the secondary winding is master, and the auxiliary winding is slave, 1 VAUX = VO x VAUX NS 9.5 Constant Current Operation To achieve this regulation the iW1696 senses the load current indirectly through the primary current. The primary current is detected by the ISENSE pin through a resistor from the BJT emitter to ground. NAUX NP VNOM Figure 9.3: Auxiliary Voltage Waveforms The auxiliary voltage is given by: VAUX = If no voltage is detected on VSENSE it is assumed that the auxiliary winding of the transformer is either open or shorted and the iW1696 shuts down. The constant current (CC mode) is useful in battery charging applications. During this mode of operation the iW1696 will regulate the output current at a constant level regardless of the output voltage, while avoiding continuous conduction mode. NAUX 0V 2 VAUX = -VIN x After soft-start has been completed, the digital control block measures the output conditions. It determines output power levels and adjusts the control system according to a light load or heavy load. If this is in the normal range, the device operates in the Constant Voltage (CV) mode, and changes the pulse width (TON) and off time (TOFF) in order to meet the output voltage regulation requirements. N AUX (VO + ∆V ) NS (9.5) CV mode CC mode E = g feedback voltage VFB. The VFB signal precisely represents the output voltage under most conditions and is used to regulate the output voltage. Output Voltage ig _ peak ( t ) = and reflects the output voltage as shown in Figure 9.3. The voltage at the load differs from the secondary voltage by a diode drop and IR losses. Thus, if the secondary voltage is always read at a constant secondary current, the difference between the output voltage and the secondary voltage will be a fixed ΔV. Furthermore, if the voltage can be read when the secondary current is small, ΔV will also be small. With the iW1696, ΔV can be ignored. Output Current IOUT(CC) Figure 9.4: Power Envelope The real-time waveform analyzer in the iW1696 reads this information cycle by cycle. The part then generates a Rev. 2.0 iW1696 February 13, 2012 Page 7 iW1696 Low-Power Off-line Digital Green-Mode PWM Controller 9.6 Multi-Mode PWM/PFM Control and Quasi-Resonant Switching The iW1696 uses an adaptive multi-mode PWM /PFM control to dramatically improve the light-load efficiency and thus the overall average efficiency. During the constant voltage (CV) operation, the iW1696 normally operates in a pulse-width-modulation (PWM) mode during heavy load conditions. In the PWM mode, the switching frequency keeps around constant. As the output load IOUT is reduced, the on-time tON is decreased, and the controller adaptively transitions to a pulse-frequencymodulation (PFM) mode. During the PFM mode, the BJT is turned on for a set duration under a given instantaneous rectified AC input voltage, but its off time is modulated by the load current. With a decreasing load current, the off time increases and thus the switching frequency decreases. As the load current is further reduced, the iW1696 transitions to a deep PFM mode (DPFM) which reduces the switching frequency to a very low level. While operating in the adaptive multi-mode PWM/PFM control, iW1696 also incorporates a unique quasi-resonant switching in both CV and CC operations. Together these innovative digital control architecture and algorithms enable iW1696 to achieve highest overall efficiency and lowest EMI. 9.7 Variable Frequency Operation Mode At each of the switching cycles, the falling edge of VSENSE will be checked. If the falling edge of VSENSE is not detected, the off-time will be extended until the falling edge of VSENSE is detected. The maximum allowed transformer reset time is 75 μs. When the transformer reset time reaches 75 μs, the iW1696 immediately shuts off. OVP threshold at point 1 indicated in figure 9.3 the iW1696 immediately shuts down. The iW1696 protects against input line undervoltage by setting a maximum TON time. Since output power is proportional to the squared VINTON product then for a given output power as VIN decreases the TON will increase. Thus by knowing when the maximum TON time occurs the iW1696 detects that the minimum VIN is reached, and shuts down. The maximum tON limit is set to 22 μs. Also, the iW1696 monitors the voltage on the VCC pin and when the voltage on this pin is below UVLO threshold the IC shuts down immediately. The output voltage is monitored through the VSENSE pin. When the overvoltage threshold is exceeded, the iW1696 will shut down immediately. When any of these faults are met the IC remains biased to discharge the VCC supply. Once VCC drops below UVLO threshold, the controller resets itself and then initiates a new soft-start cycle. The controller continues attempting start-up until the fault condition is removed. 9.10 PCL, OCP and SRS Protection Peak-current limit (PCL), over-current protection (OCP) and sense-resistor short protection (SRSP) are features built-in to the iW1696. With the ISENSE pin the iW1696 is able to monitor the peak primary current. This allows for cycle by cycle peak current control and limit. When the primary peak current multiplied by the ISENSE resistor is greater than 1.1 V over current (OCP) is detected and the IC will immediately turn off the base driver until the next cycle. The output driver will send out a switching pulse in the next cycle, and the switching pulse will continue if the OCP threshold is not reached; or, the switching pulse will turn off again if the OCP threshold is reached. If the OCP occurs for several consecutive switching cycles, the iW1696 shuts down. The iW1696 incorporates an internal Digital Error Amplifier with no requirement for external loop compensation. For a typical power supply design, the loop stability is guaranteed to provide at least 45 degrees of phase margin and -20 dB of gain margin. If the ISENSE resistor is shorted there is a potential danger of the over current condition not being detected. Thus, the IC is designed to detect this sense-resistor-short fault after startup and shut down immediately. The VCC will be discharged since the IC remains biased. Once VCC drops below the UVLO threshold, the controller resets itself and then initiates a new soft-start cycle. The controller continues attempting to startup, but does not fully startup until the fault condition is removed. 9.9 Voltage Protection Features 9.11 Dynamic Base Current Control The secondary maximum output DC voltage is limited by the iW1696. When the VSENSE signal exceeds the output One important feature of the iW1696 is that it directly drives a BJT switching device with dynamic base current control to optimize performance. The BJT base current ranges from 9.8 Internal Loop Compensation Rev. 2.0 iW1696 February 13, 2012 Page 8 iW1696 Low-Power Off-line Digital Green-Mode PWM Controller 10 mA to 31 mA, and is dynamically controlled according to the power supply load change. The higher the output power, the higher the base current. Specifically, the base current is related to VIPK, as shown in Figure 9.5. 35 Base Drive Current (mA) 30 25 20 15 10 5 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 VIPK (V) Figure 9.5: Base Drive Current vs. VIPK 9.12 Cable Drop Compensation The iW1696 incorporates an innovative method to compensate for any IR drop in the secondary circuitry including cable and cable connector. A 2.5 W adapter with 5 V DC output has 3% deviation at 0.5 A load current due to the drop across a 24 AWG, 1.8 meter DC cable without cable compensation. The iW1696 compensates for this voltage drop by providing a voltage offset to the feedback signal based on the amount of load current detected. To calculate the amount of cable compensation needed, take the resistance of the cable and connector and multiply by the maximum output current. Rev. 2.0 iW1696 February 13, 2012 Page 9 iW1696 Low-Power Off-line Digital Green-Mode PWM Controller 10.0 Physical Dimensions 5-Lead SOT Package 5 4 E E1 1 2 3 Symbol D MIN MAX A - 1.45 A1 0.0 0.15 A2 0.90 1.30 B 0.30 0.50 C 0.08 0.22 e e1 D A1 A2 B COPLANARITY 0.10 A SEATING PLANE α Millimeters 2.90 BSC E 2.80 BSC E1 1.60 BSC e 0.95 BSC e1 L C 1.90 BSC L 0.30 0.60 α 0° 8° Figure 10.1: Physical dimensions, 5-lead SOT-23 package Compliant to JEDEC Standard MO178 Controlling dimensions are in millimeters This package is RoHS compliant, and conform to Halide free limits. Soldering Temperature Resistance: [a] Package is IPC/JEDEC Std 020D Moisture Sensitivity Level 1 [b] Package exceeds JEDEC Std No. 22-A111 for Solder Immersion resistance; packages can withstand 10 s immersion @ < 270 °C Dimension D does not include mold flash, protrusions or gate burrs. Mold flash, protrusions or gate burrs shall not exceed 0.25 mm per end. Dimension E1 does not include interlead flash or protrusion. Interlead flash or protrusion shall not exceed 0.25 mm per side. The package top may be smaller than the package bottom. Dimension D and E1 are determined at the outermost extremes of the plastic body exclusive of mold flash, tie bar burrs, gate burrs and interlead flash, but including any mismatch between the top and bottom of the plastic body. 11.0 Ordering Information Part Number Options Package Description iW1696-00 Cable Comp = 0 mV SOT-23 Tape & Reel1 iW1696-01 Cable Comp = 300 mV SOT-23 Tape & Reel1 iW1696-03 Cable Comp = 450 mV SOT-23 Tape & Reel1 iW1696-04 Cable Comp = 150 mV SOT-23 Tape & Reel1 Note 1: Tape & Reel packing quantity is 3,000 per reel. Minimum ordering quantity is 3,000. Rev. 2.0 iW1696 February 13, 2012 Page 10 iW1696 Low-Power Off-line Digital Green-Mode PWM Controller About iWatt iWatt Inc. is a fabless semiconductor company that develops intelligent power management ICs for computer, communication, and consumer markets. The company’s patented pulseTrain™ technology, the industry’s first truly digital approach to power system regulation, is revolutionizing power supply design. Trademark Information © 2012 iWatt, Inc. All rights reserved. iWatt, EZ-EMI, and pulseTrain are trademarks of iWatt, Inc. All other trademarks and registered trademarks are the property of their respective companies. Contact Information Web: https://www.iwatt.com E-mail: [email protected] Phone: 408-374-4200 Fax: 408-341-0455 iWatt Inc. 675 Campbell Technology Parkway, Suite 150 Campbell, CA 95008 Disclaimer iWatt reserves the right to make changes to its products and to discontinue products without notice. The applications information, schematic diagrams, and other reference information included herein is provided as a design aid only and are therefore provided as-is. iWatt makes no warranties with respect to this information and disclaims any implied warranties of merchantability or non-infringement of third-party intellectual property rights. iWatt cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in an iWatt product. No circuit patent licenses are implied. Certain applications using semiconductor products may involve potential risks of death, personal injury, or severe property or environmental damage (“Critical Applications”). IWATT SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE‑SUPPORT APPLICATIONS, DEVICES OR SYSTEMS, OR OTHER CRITICAL APPLICATIONS. Inclusion of iWatt products in critical applications is understood to be fully at the risk of the customer. Questions concerning potential risk applications should be directed to iWatt, Inc. iWatt semiconductors are typically used in power supplies in which high voltages are present during operation. High-voltage safety precautions should be observed in design and operation to minimize the chance of injury. Rev. 2.0 iW1696 February 13, 2012 Page 11