CRE1 Series www.murata-ps.com Isolated 1W Single Output Isolated DC-DC Converters 5 5 5 12 12 24 24 5 5 15 5 12 5 12 200 200 67 200 83 200 83 CRE1S0305S3C CRE1S0505S3C 3.3 5 5 5 200 200 n 3.3V, 5V, 12V & 24V Inputs CRE1S0505MC CRE1S0505MEC 5 5 5 5 200 200 n 5V, 12V & 15V outputs INPUT CHARACTERISTICS FEATURES n UL 60950 recognised3 n Single Isolated output n 1kVDC or 3kVDC option ‘Hi Pot Test’ n Wide temperature performance at full n 1W load -40°C to 85°C4 n Industry Standard Pinout n Pin Compatible with CME, CRL2, LME, MEE1, MEE3, MTE1, NKE, NME, NML & NTE series Parameter Voltage range n Through hole and surface mount options n available PRODUCT OVERVIEW The CRE1 series are a cost effective 1W DC-DC converter series, in industry standard packages with industry standard pinout. Popular input and output voltages are available. The galvanic isolation allows the device to be configured to provide an isolated negative rail in systems where only positive rails exist. The wide temperature range guarantees startup from –40°C and full 1 watt output at 85°C3. Reflected ripple current Ripple & Noise 12 14 16 40 12 14 16 40 6 7.5 10 25 8 10 12 30 4 5 8 20 8.5 10 13 30 3 4 10 25 3KVDC isolation options 10 12 15 25 6 8 15 25 Surface mount options 12.8 15 62 85 6.5 8 25 70 MTTF2 CRE1S0505DC CRE1S0505SC CRE1S0515SC CRE1S1205SC CRE1S1212SC CRE1S2405SC CRE1S2412SC % mV p-p Typ. Max. Typ. Max. Isolation Capacitance mA Efficiency V Input Current at Rated Load V Load Regulation Output Current Nominal Input Voltage Output Voltage Order Code1 SELECTION GUIDE mA % Min. Typ. pF MIL. Tel. kHrs 286 286 250 117 104 58 52 65 65 77 68 75 67 75 70 70 80 71 80 71 80 30 30 40 33 55 40 78 400 250 72 73 75 77 35 24 294 239 79 68 82 35 22 6857 3041 Conditions Min. Typ. Max. Continuous operation, 3.3V input types Continuous operation, 5V input types Continuous operation, 12V input types Continuous operation, 24V input types 3.3V & 12V input types 5V & 24V input types CRE1S0505MC CRE1S0505MEC 2.97 4.5 10.8 21.6 3.3 5.0 12 24 1 2 30 5 3.63 5.5 13.2 26.4 15 15 47 15 Units Typ. Max. Units 1 W 1.2 %/% Max. Units V mA p-p OUTPUT CHARACTERISTICS Parameter Conditions Rated Power Voltage Set Point Accuracy Line regulation TA=-40°C to 85°C3 See tolerance envelope High VIN to low VIN Min. 1.1 ISOLATION CHARACTERISTICS Parameter Isolation test voltage Resistance Conditions Min. C Versions Flash tested for 1 second 3C Versions Flash tested for 1 second Viso= 1000VDC 1000 3000 Typ. VDC 10 GΩ GENERAL CHARACTERISTICS Parameter Conditions Switching frequency 3.3V input types 5V input types 12V input types 24V input types CRE1S0505MEC Min. Typ. Max. 115 110 145 100 80 Units kHz 1. If components are required in tape and reel format suffix order code with -R, e.g. CRE1S0505MC-R. 2. Calculated using MIL-HDBK-217 FN2 and Telcordia SR-332 calculation model with nominal input voltage at full load. 3. UL 60950 recognition does not apply to CRE1S0505MC. 4. 24V input parts prior to date code D1635 have operating temperature range of 0 to 70°C. For full details go to www.murata-ps.com/rohs All specifications typical at TA=25°C, nominal input voltage and rated output current unless otherwise specified. www.murata-ps.com/support KDC_CRE1.D02 Page 1 of 14 CRE1 Series Isolated 1W Single Output Isolated DC-DC Converters ABSOLUTE MAXIMUM RATINGS Lead temperature 1.5mm from case for 10 seconds Input voltage VIN, 3.3V input Input voltage VIN, 5V input Input voltage VIN, 12V input Input voltage VIN, 24V input 260°C 5.5V 7V 15V 28V TEMPERATURE CHARACTERISTICS Parameter Conditions Min. Specification Storage All output types1 -40 -50 Case temperature rise above ambient Cooling 5V output types All other output types CRE1S0505MC CRE1S0505MEC Free air convection Typ. Max. Units 85 130 41 32 °C 43 12.5 TECHNICAL NOTES ISOLATION VOLTAGE ‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage, applied for a specified time, across a component designed to provide electrical isolation, to verify the integrity of that isolation. Murata Power Solutions CRE1 series of DC-DC converters are all 100% production tested at their stated isolation voltage. This is 1kVDC for 1 second for C versions and 3kVDC for 1 second for 3C versions. A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?” The CRE1 series, through hole variants (excluding surface mount variants) have been recognised by Underwriters Laboratory for functional insulation, both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or 60VDC. The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry according to safety standard requirements. REPEATED HIGH-VOLTAGE ISOLATION TESTING It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials, construction and environment. The CRE1 series has toroidal isolation transformers, with no additional insulation between primary and secondary windings of enamelled wire. While parts can be expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel (typically polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited. We therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from specified test voltage. This consideration equally applies to agency recognized parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further insulation system of physical spacing or barriers. SAFETY APPROVAL The CRE1 series has been recognised by Underwriters Laboratory (UL) to UL60950 for functional insulation in a maximum still air ambient temperature of 100°C for the C versions and 130°C for the 3C versions as measured on the case of the unit (hotspot). The CRE1S0505MC is not currently UL recognised. The CRE1 series of converters are not internally fused so to meet the requirements of UL60950 an anti-surge input line fuse should always be used with ratings as defined below. CRE1S03xxS3C: 1A CRE1S05xxxxC: 0.7A CRE1S12xxSC: 0.2A CRE1S24xxSC: 0.16A All fuses should be UL recognised, 125V rated. File number E151252 applies. 1. 24V input parts prior to date code D1635 have operating temperature range of 0 to 70°C. www.murata-ps.com/support KDC_CRE1.D02 Page 2 of 14 CRE1 Series Isolated 1W Single Output Isolated DC-DC Converters TEMPERATURE DERATING GRAPH - All other types1 85°C 1.0 Output Power (W) Output Power (W) TEMPERATURE DERATING GRAPH - Surface Mount & 3C types Safe Operating Area 0 -40 100 50 0 Ambient Temperature (°C) 85°C 1.0 Safe Operating Area 120°C 0 -40 150 100 50 0 Ambient Temperature (°C) 150 EFFICIENCY VS LOAD 3.3V Inputs 5V Inputs CRE1S0305S3C 90 90 80 80 70 70 60 50 CRE1S0305S3C 40 Efficiency (%) Efficiency (%) 60 CRE1S0515SC CRE1S0505S3C 40 30 30 20 20 10 10 0 CRE1S0505MC CRE1S0505MEC 0 0 10 20 30 40 50 60 70 80 90 100 0 10 20 30 40 50 60 Load (%) Load (%) 12V Inputs 24V Inputs 90 90 80 80 70 70 70 80 90 100 60 50 CRE1S1205SC 40 CRE1S1212SC Efficiency (%) 60 Efficiency (%) CRE1S0505XC 50 50 CRE1S2405SC 40 CRE1S2412SC 30 30 20 20 10 10 0 0 0 10 20 30 40 50 60 70 80 90 100 Load (%) 0 10 20 30 40 50 60 70 80 90 100 Load (%) 1. 24V input parts prior to date code D1635 have operating temperature range of 0 to 70°C. www.murata-ps.com/support KDC_CRE1.D02 Page 3 of 14 CRE1 Series Isolated 1W Single Output Isolated DC-DC Converters TOLERANCE ENVELOPES The voltage tolerance envelope shows typical load regulation characteristics for this product series. The tolerance envelope is the maximum output voltage variation due to changes in output loading. CRE1S0505XC CRE1S0515SC 10% 7% 0% Output Voltage Output Voltage 6% 3% 0% -3% -6% 10 25 50 75 100 10 25 50 75 100 Output Load Current (%) Output Load Current (%) CRE1S1205SC CRE1S1212SC 7% 2% 1% Output Voltage Output Voltage 5% 3% 2% -1% -6% 10 25 75 50 Output Load Current (%) 100 CRE1S2405SC 10 25 75 50 Output Load Current (%) 100 CRE1S2412SC 5% 1% Output Voltage Output Voltage 8% 2% 0% -1% -3% 10 25 50 Output Load Current (%) 75 100 -4% 10 25 75 50 Output Load Current (%) 100 www.murata-ps.com/support KDC_CRE1.D02 Page 4 of 14 CRE1 Series Isolated 1W Single Output Isolated DC-DC Converters TOLERANCE ENVELOPES (continued) CRE1S0305S3C CRE1S0505S3C 9% Output Voltage Output Voltage 7% 6% 0% 3% 1% -3% -5% 10 25 50 Output Load Current (%) 75 100 10 CRE1S0505MC 25 50 Output Load Current (%) 75 100 CRE1S0505MEC 10% 3% 0% Output Voltage Output Voltage 7% 3% 2% -4% 10 25 50 Output Load Current (%) 75 100 -8% 10 25 50 Output Load Current (%) 75 100 RoHS COMPLIANCE and MSL INFORMATION The Through Hole parts (SIP/DIP) in this series are compatible with RoHS soldering systems with a peak wave solder temperature of 260°C for 10 seconds. The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. This series is backward compatible with Sn/Pb soldering systems. The Surface Mount parts (MC/MEC) in this series are compatible with RoHS soldering systems as per J-STD-020D.1 The pin termination finish on the Surface Mount package types is Matte Tin over Nickel Preplate. This series is backward compatible with Sn/Pb soldering systems. The Surface Mount parts have a Moisture Sensitivity Level (MSL) 1. Samples of the Surface Mount parts were tested in accordance with the conditioning described for MSL level 1 in IDC/J-STD-020D.1. The products passed electrical tests and visual inspection criteria. For further information, please visit www.murata-ps.com/rohs www.murata-ps.com/support KDC_CRE1.D02 Page 5 of 14 CRE1 Series Isolated 1W Single Output Isolated DC-DC Converters APPLICATION NOTES Minimum load The minimum load to meet datasheet specification is 10% of the full rated load across the specified input voltage range. Lower than 10% minimum loading will result in an increase in output voltage, which may rise to typically double the specified output voltage if the output load falls to less than 5%. Capacitive loading and start up Typical start up times for this series, with a typical input voltage rise time of 2.2µs and output capacitance of 10µF, are shown in the table below. The product series will start into a capacitance of 47µF with an increased start time, however, the maximum recommended output capacitance is 10µF. CRE1S0505DC CRE1S0505SC CRE1S0515SC CRE1S1205SC CRE1S1212SC CRE1S2405SC CRE1S2412SC CRE1S0305S3C CRE1S0505S3C CRE1S0505MC CRE1S0505MEC Start-up time µs 190 190 1790 125 500 135 430 295 165 1368 170 Typical Start-Up Wave Form www.murata-ps.com/support KDC_CRE1.D02 Page 6 of 14 CRE1 Series Isolated 1W Single Output Isolated DC-DC Converters APPLICATION NOTES (continued) Ripple & Noise Characterisation Method Ripple and noise measurements are performed with the following test configuration. C1 1µF X7R multilayer ceramic capacitor, voltage rating to be a minimum of 3 times the output voltage of the DC-DC converter 10µF tantalum capacitor, voltage rating to be a minimum of 1.5 times the output voltage of the DC-DC converter with an ESR of less C2 than 100mΩ at 100 kHz C3 100nF multilayer ceramic capacitor, general purpose R1 450Ω resistor, carbon film, ±1% tolerance R2 50Ω BNC termination T1 3T of the coax cable through a ferrite toroid RLOAD Resistive load to the maximum power rating of the DC-DC converter. Connections should be made via twisted wires Measured values are multiplied by 10 to obtain the specified values. Differential Mode Noise Test Schematic DC/DC Converter C1 C2 C3 + SUPPLY Input - R1 R2 T1 + OSCILLOSCOPE Y INPUT Output - R LOAD Output Ripple Reduction By using the values of inductance and capacitance stated, the output ripple at the rated load is lowered to 5mV p-p max. Component selection Capacitor: It is required that the ESR (Equivalent Series Resistance) should be as low as possible, ceramic types are recommended. The voltage rating should be at least twice (except for 15V output), the rated output voltage of the DC-DC converter. Inductor: The rated current of the inductor should not be less than that of the output of the DC-DC converter. At the rated current, the DC resistance of the inductor should be such that the voltage drop across the inductor is <2% of the rated voltage of the DC-DC converter. The SRF (Self Resonant Frequency) should be >20MHz. L DC Power Source CRE1S0505DC CRE1S0505SC CRE1S0515SC CRE1S1205SC CRE1S1212SC CRE1S2405SC CRE1S2412SC CRE1S0305S3C CRE1S0505S3C CRE1S0505MC CRE1S0505MEC C Load DC L, µH Inductor SMD Through Hole Capacitor C, µF 47 10 82473C 82103C 11R473C 11R103C 4.7 4.7 www.murata-ps.com/support KDC_CRE1.D02 Page 7 of 14 CRE1 Series Isolated 1W Single Output Isolated DC-DC Converters EMC FILTERING AND SPECTRA FILTERING The following table shows the additional input capacitor and input inductor typically required to meet EN 55022 Curve B Quasi-Peak EMC limit, as shown in the following plots. The following plots show positive and negative quasi peak and CISPR22 Average Limit B (pink line) and Quasi Peak Limit B (green line) adherence limits.The below values are for guidance only and should be evaluated in the application circuit. For the CRE1S0505MEC an input inductor is not required. L DC C DC Inductor Part Number L, µH SMD Through Hole C, µF CRE1S0505DC CRE1S0505SC CRE1S0515SC CRE1S1205SC CRE1S1212SC CRE1S2405SC CRE1S2412SC CRE1S0305S3C CRE1S0505S3C CRE1S0505MC CRE1S0505MEC 4.7 4.7 4.7 10 10 22 22 10 10 10 NR 82472C 82472C 82472C 82103C 82103C 82223C 82223C 82103C 82103C 82103C NR 13R472C 13R472C 13R472C 13R103C 13R103C 13R223C 13R223C 13R103C 13R103C 13R103C NR 4.7 4.7 4.7 1 1 10 10 1 1 4.7 22 Capacitor Rated Recommended Part Voltage Number 16VDC GRM188Z71C475ME21 16VDC GRM188Z71C475ME21 16VDC GRM188Z71C475ME21 50VDC GRM21BR71H105KA12 50VDC GRM21BR71H105KA12 50VDC GRM32ER71H106MA12 50VDC GRM32ER71H106MA12 50VDC GRM188R71C105MA12 50VDC GRM188R71C105MA12 16VDC GRM188Z71C475ME21 10VDC GRM32ER71A226ME20 NR - Not required 80 70 70 60 60 50 50 dBuV 80 40 40 30 30 20 20 10 10 0 1.00E+05 dBuV CRE1S0515SC 1.00E+06 1.00E+07 0 1.00E+05 1.00E+08 1.00E+07 Frequency (Hz) CRE1S1205SC CRE1S1212SC 80 80 70 70 60 60 50 50 40 30 20 20 10 10 1.00E+06 1.00E+07 Frequency (Hz) 1.00E+08 1.00E+08 40 30 0 1.00E+05 1.00E+06 Frequency (Hz) dBuV dBuV CRE1S0505XC 0 1.00E+05 1.00E+06 1.00E+07 1.00E+08 Frequency (Hz) www.murata-ps.com/support KDC_CRE1.D02 Page 8 of 14 CRE1 Series Isolated 1W Single Output Isolated DC-DC Converters EMC FILTERING AND SPECTRA CRE1S2412SC 80 80 70 70 60 60 50 50 dBuV dBuV CRE1S2405SC 40 40 30 30 20 20 10 10 0 1.00E+05 1.00E+06 1.00E+07 0 1.00E+05 1.00E+08 80 80 70 70 60 60 50 50 40 40 30 30 20 20 10 10 1.00E+07 0 1.00E+05 1.00E+08 80 80 70 70 60 60 50 50 40 30 20 20 10 10 Frequency (Hz) 1.00E+08 40 30 1.00E+07 1.00E+07 CRE1S0505MEC dBuV dBuV CRE1S0505MC 1.00E+06 1.00E+06 Frequency (Hz) Frequency (Hz) 0 1.00E+05 1.00E+08 CRE1S0505S3C dBuV dBuV CRE1S0305S3C 1.00E+06 1.00E+07 Frequency (Hz) Frequency (Hz) 0 1.00E+05 1.00E+06 1.00E+08 0 1.00E+05 1.00E+06 1.00E+07 1.00E+08 Frequency (Hz) www.murata-ps.com/support KDC_CRE1.D02 Page 9 of 14 CRE1 Series Isolated 1W Single Output Isolated DC-DC Converters PACKAGE SPECIFICATIONS SC Package DC Package 3C Package CRE1S 0505DC XYYWW 11.53±0.2 [0.454±0.008] 4.10±0.5 [0.161±0.020] CRE1S XXXXSC 0.40 [0.016] MIN 10.00±0.25 [0.394±0.010] XYYWW 1 2 3 2.54 [0.100] XYYWW S 1 4.10±0.5 [0.161±0.020] 4 2.54 [0.100] 0.50±0.05 [0.020±0.002] 6.10 +0.15 -0.20 (1.13 [0.044]) CRE1S XXXXS3C 7.46±0.25 [0.294±0.010] (1.95 [0.077]) 0.25±0.05 [0 .010±0.002] (2.21 [0.087]) 0.40 [0.016] MIN 11.53±0.2 [0.454±0.008] -0.008 ] [0.240 +0.006 (1.13 [0.044]) 2 3 S 4 0.50±0.05 [0.020±0.002] 0.25±0.05 [0.010±0.002] 6.10 +0.15 -0.25 -0.010 ] [0.240 +0.006 All dimensions in mm (inches) Controlling dimension is mm. All pins on a 2.54 (0.100) pitch and within ±0.1 (0.004) of true position from pin 1 at seating plane ‘S’ (SC&3C) All pins on a 2.54 (0.100) pitch and within ±0.25 (0.010) of true position (DC) PIN CONNECTIONS SC & 3C - 4 PIN SIP Weight: 1.09g (3C) 1.30g (SC) 1.38g (DC) PIN CONNECTIONS DC - 8 PIN DIP Function Pin -VIN 1 -VIN 2 +VIN 4 +VIN 3 -VOUT 5 +VOUT 4 +VOUT 7 -VOUT Pin 1 Function www.murata-ps.com/support KDC_CRE1.D02 Page 10 of 14 CRE1 Series Isolated 1W Single Output Isolated DC-DC Converters PACKAGE SPECIFICATIONS (Continued) CRE1S0505MC CRE1S0505MEC 12.70±0.20 (0.500±0.008) 7.62 (0.300) 12.70 (0.500) 7.62 (0.300) 7.70(0.303) 10.90± 0.3 (0.43 ± 0.012) 14 14 DETAIL A XYYWW 3 11.00±0.15 (0.433±0.006) P 1.50 (0.059) 1.20 (0.047) 7 0.65 (0.026) 0.55 (0.022) 2.54 (0.100) 0.50 (0.020) REFERENCE PLANE CRE1S0505MC 1 10 PINS 0.2 (0.008) XYYWW ±5.00° 1 S S SEATING PLANE 7.05 0.25 (0.010) 0.10 (0.004) CRE1S0505MEC 3 7 0.6±0.05 (0.024±0.002) DETAIL A 6.60 (0.260) 6.35 (0.250) 5.95 (0.234) 5.85 (0.230) 0.1(0.004) S 10.70±0.15 (0.421±0.006) 2.54 (0.100) 2.10 (0.083) 2.79 (0.110) MAX 8 8 (1.875 MAX) +0.35 ( 0.278 +0.014 ) -0.10 -0.004 0.30 (0.012) 0.20 (0.008) 0.2 (0.008) Min. 2.54±0.15 (0.100±0.006) x5 Pins 0.10 S 0.25±0.05 (0.010±0.002) 1.56±0.10 (0.061±0.004) All dimensions in mm (inches) Controlling dimension is mm. All pins on a 2.54 (0.100) pitch and within ±0.25 (0.010) of true position PIN CONNECTIONS - CRE1SXXXXMC/MEC Pin Function 1 -VIN 3 +VIN 7 -VOUT 8 +VOUT 14 NA Weight: 1.2g www.murata-ps.com/support KDC_CRE1.D02 Page 11 of 14 CRE1 Series Isolated 1W Single Output Isolated DC-DC Converters PACKAGE SPECIFICATIONS (continued) RECOMMENDED FOOTPRINT DETAILS DC SC/3C 2.54 [0.100] x4 HOLES Ø 0.045 0.039 Ø 1.15 1.00 [ ] 2.54 [0.100] TUBE OUTLINE DIMENSIONS DC Tube 3C Tube SC Tube 12.0 [0.472] 9.3 [0.366] 7.7 [0.303] 9.3 [0.366] 12.43 [0.489] 14.5 [0.571] 14.8 [0.583] 18.0 [0.709] 5.07±0.80 [0.200±0.03] 5.05 [0.199] Unless otherwise specified all dimensions in mm [inches] ±0.55mm [0.022]. Tube Length (DC&SC) : 520mm [20.472] ±2.0 [0.079] Tube Length (3C) : 525mm [20.669] ±2.0 [0.079]. 5.0 [0.197] 4.45 [0.175] Tube Quantity (DC & SC): 35 (3C):40 www.murata-ps.com/support KDC_CRE1.D02 Page 12 of 14 CRE1 Series Isolated 1W Single Output Isolated DC-DC Converters PACKAGE SPECIFICATIONS (continued) RECOMMENDED FOOTPRINT DETAILS 7.62 (0.3) 2.00 (0.079) 9.70 (0.382) 2.54 (0.1) 1.00 (0.040) MIN TUBE OUTLINE DIMENSIONS CRE1S0505MC CRE1S0505MEC 0.60±0.15 (0.024±0.006) 9.40 (0.370) 14.35 (0.565) 14.85 (0.59) 11.40 (0.45) 2.10 (0.083) 6.70 (0.264) 9.05 (0.36) Unless otherwise specified all dimensions in mm [inches] ±0.55mm [0.022]. Tube Length (MC&MEC) : 475±2.0 (18.70±0.07). Tube Quantity (MC): 35 (MEC): 30 www.murata-ps.com/support KDC_CRE1.D02 Page 13 of 14 CRE1 Series Isolated 1W Single Output Isolated DC-DC Converters TAPE & REEL SPECIFICATIONS REEL OUTLINE DIMENSIONS TAPE OUTLINE DIMENSIONS 330±2.0 (12.99±0.08) 13.25 (0.52) 0.60 (0.02) Max. Ø100 (3.94) DIRECTION OF UNREELING +0.004 (+0.10) -0.00 (-0.00) 2.00 (0.08) 13.00±0.5 Ø (0.51±0.02) 30.40(1.20) MAX 24.40 (0.96) 2.00(+0.08) (AT HUB SECTION) -0.00(0.00) 1.50 (Ø0.06) 16.00 (0.63) 11.50 (0.45) 4.00 (0.16) 1.75(0.07) 11.50 (0.45) 8.10 (0.32) 24.00±0.30 (0.94±0.01) REEL PACKAGING DETAILS GOODS ENCLOSURE SECTION CRE1S0505MC XYYWW XYYWW CRE1S0505MEC XYYWW Reel Quantity: 500 TRAILER SECTION 160 (6.30) MIN CRE1S0505MC Product Orientation Pin 1, located nearest to carrier drive sprocket. CARRIER TAPE START 100 (3.94) MIN LEADER SECTION 400 (15.75) MIN This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Refer to: http://www.murata-ps.com/requirements/ Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. © 2018 Murata Power Solutions, Inc. www.murata-ps.com/support KDC_CRE1.D02 Page 14 of 14