M54HC107 M74HC107 DUAL J-K FLIP FLOP WITH CLEAR . . . . . . . . HIGH SPEED fMAX = 75 MHz (TYP.) AT VCC = 5 V LOW POWER DISSIPATION ICC = 2 µA (MAX.) AT TA = 25 °C HIGH NOISE IMMUNITY VNIH = VNIL = 28 % VCC (MIN.) OUTPUT DRIVE CAPABILITY 10 LSTTL LOADS SYMMETRICAL OUTPUT IMPEDANCE IOH = IOL = 4 mA (MIN.) BALANCED PROPAGATION DELAYS tPLH = tPHL WIDE OPERATING VOLTAGE RANGE VCC (OPR) = 2 V TO 6 V PIN AND FUNCTION COMPATIBLE WITH 54/74LS107 B1R (Plastic Package) F1R (Ceramic Package) M1R (Micro Package) C1R (Chip Carrier) ORDER CODES : M54HC107F1R M74HC107M1R M74HC107B1R M74HC107C1R PIN CONNECTIONS (top view) DESCRIPTION The M54/74HC107 is a high speed CMOS DUAL JK FLIP FLOP fabricated in silicon gate C2MOS technology. It has the same high speed performance of LSTTL combined with true CMOS low power consumption. These flip-flop are edge sensitive to the clock input and change state on the negative going transition of the clock pulse. Each one has independent J, K, CLOCK, and CLEAR input and Q and Q outputs. CLEAR is independent of the clock and accomplished by a logic low on the input. All inputs are equipped with protection circuits against static discharge and transient excess voltage. INPUT AND OUTPUT EQUIVALENT CIRCUIT NC = No Internal Connection October 1992 1/11 M54/M74HC107 TRUTH TABLE INPUTS OUTPUTS CLR L J X K X H L H H CK X Q H L Qn Qn L H H L L H H L H H H Qn Qn TOGGLE H X X Qn Qn NO CHANGE X: Don’t Care PIN DESCRIPTION IEC LOGIC SYMBOL PIN No SYMBOL NAME AND FUNCTION 1, 8, 4, 11 1J, 2J, 1K, 2K Synchronous Inputs; Flip-Flop 1 And 2 2, 6 1Q, 2Q Complement Flip-Flop Outputs 3, 5 12, 9 1Q, 2Q 1CK, 2CK True Flip-Flop Outputs Clock Input 13, 10 1CLR, 2CLR Asynchronous Reset Inputs 7 14 GND V CC Ground (0V) Positive Supply Voltage LOGIC DIAGRAM (1/2 Package) 2/11 FUNCTION Q L CLEAR NO CHANGE M54/M74HC107 ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit VCC VI Supply Voltage DC Input Voltage -0.5 to +7 -0.5 to VDD + 0.5 V V VO DC Output Voltage -0.5 to VDD + 0.5 V IIK IOK DC Input Diode Current DC Output Diode Current ± 20 ± 20 mA mA IO DC Output Source Sink Current Per Output Pin ± 25 mA DC VCC or Ground Current ± 50 mA 500 (*) mW ICC or IGND PD Power Dissipation Tstg Storage Temperature -65 to +150 o C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition isnotimplied. (*) 500 mW: ≅ 65 oC derate to 300 mW by 10mW/oC: 65 oC to 85 oC RECOMMENDED OPERATING CONDITIONS Symbol VCC Parameter Supply Voltage VI Input Voltage VO Top Output Voltage Operating Temperature: M54HC Series M74HC Series tr, tf Input Rise and Fall Time Value 2 to 6 Unit V 0 to VCC V 0 to VCC -55 to +125 -40 to +85 VCC = 2 V 0 to 1000 VCC = 4.5 V VCC = 6 V 0 to 500 0 to 400 V C o C o ns 3/11 M54/M74HC107 DC SPECIFICATIONS Test Conditions Symbol VIH V IL V OH Parameter High Level Input Voltage Low Level Input Voltage High Level Output Voltage II ICC 4/11 Low Level Output Voltage Input Leakage Current Quiescent Supply Current TA = 25 C 54HC and 74HC Min. Typ. Max. VCC (V) -40 to 85 oC -55 to 125 oC 74HC 54HC Min. Max. Min. Max. 2.0 1.5 1.5 1.5 4.5 6.0 3.15 4.2 3.15 4.2 3.15 4.2 2.0 0.5 0.5 0.5 1.35 1.35 1.35 6.0 1.8 1.8 1.8 2.0 4.5 6.0 6.0 2.0 Unit V 4.5 4.5 VOL Value o VI = IO=-20 µA VIH or V IL IO=-4.0 mA 1.9 2.0 1.9 1.9 4.4 5.9 4.5 6.0 4.4 5.9 4.4 5.9 4.18 4.31 4.13 4.10 IO=-5.2 mA 5.68 5.8 0.0 5.63 0.1 0.1 0.1 V V 5.60 0.0 0.1 0.1 0.1 6.0 4.5 VI = IO= 20 µA VIH or V IL IO= 4.0 mA 0.0 0.17 0.1 0.26 0.1 0.33 0.1 0.40 6.0 IO= 5.2 mA 0.18 0.26 0.33 0.40 VI = VCC or GND ±0.1 ±1 ±1 µA VI = VCC or GND 2 20 40 µA 4.5 6.0 6.0 V M54/M74HC107 AC ELECTRICAL CHARACTERISTICS (C L = 50 pF, Input t r = tf = 6 ns) Test Conditions Symbol Parameter tTLH tTHL Output Transition Time tPLH tPHL Propagation Delay Time (CK - Q, Q) tPLH tPHL Propagation Delay Time (CLR - Q, Q) fMAX Maximum Clock Frequency tW(H) tW(L) Minimum Pulse Width (CLOCK) tW(L) Minimum Pulse Width (CLR) ts th tREM CIN CPD (*) Minimum Set-up Time Minimum Hold Time Minimum Removal Time (CLR) Input Capacitance Power Dissipation Capacitance Value o VCC (V) TA = 25 C 54HC and 74HC Min. Typ. Max. -40 to 85 oC -55 to 125 oC 74HC 54HC Min. Max. Min. Max. 2.0 30 75 95 110 4.5 6.0 8 7 15 13 19 16 22 19 2.0 48 125 155 190 4.5 14 25 31 38 6.0 12 21 26 32 2.0 52 140 175 210 4.5 6.0 15 13 28 24 35 30 42 36 2.0 6.2 23 5.0 4.2 4.5 6.0 31 37 70 80 25 30 21 25 2.0 20 75 95 110 5 4 15 13 19 16 22 19 2.0 20 75 95 110 4.5 6.0 5 4 15 13 19 16 22 19 2.0 28 75 95 110 4.5 6.0 7 6 15 13 19 16 22 19 0 0 0 0 0 0 6.0 0 0 0 2.0 4.5 25 5 30 6 40 8 6.0 5 32 ns ns ns MHz 4.5 6.0 2.0 4.5 Unit 5 5 7 10 10 10 ns ns ns ns ns pF pF (*) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operting current can be obtained by the following equation. ICC(opr) = CPD •VCC •fIN + ICC/2 (per FLIP/FLOP) 5/11 M54/M74HC107 SWITCHING CHARACTERISTICS TEST TEST CIRCUIT ICC (Opr.) TRANSITION TIME OF INPUT WAVEFORM IS THE SAVE AS THAT IN CASE OF SWITCHING CHARACTERISTICSTEST. SWITCHING CHARACTERISTICS TEST WAVEFORM 6/11 M54/M74HC107 Plastic DIP14 MECHANICAL DATA mm DIM. MIN. a1 0.51 B 1.39 TYP. inch MAX. MIN. TYP. MAX. 0.020 1.65 0.055 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 15.24 0.600 F 7.1 0.280 I 5.1 0.201 L Z 3.3 1.27 0.130 2.54 0.050 0.100 P001A 7/11 M54/M74HC107 Ceramic DIP14/1 MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 20 0.787 B 7.0 0.276 D E 3.3 0.130 0.38 e3 0.015 15.24 0.600 F 2.29 2.79 0.090 0.110 G 0.4 0.55 0.016 0.022 H 1.17 1.52 0.046 0.060 L 0.22 0.31 0.009 0.012 M 1.52 2.54 0.060 0.100 N P Q 10.3 7.8 8.05 5.08 0.406 0.307 0.317 0.200 P053C 8/11 M54/M74HC107 SO14 MECHANICAL DATA mm DIM. MIN. TYP. A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.2 a2 MAX. 0.003 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45° (typ.) D 8.55 E 5.8 8.75 0.336 6.2 0.228 0.344 0.244 e 1.27 0.050 e3 7.62 0.300 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M S 0.68 0.026 8° (max.) P013G 9/11 M54/M74HC107 PLCC20 MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 9.78 10.03 0.385 0.395 B 8.89 9.04 0.350 0.356 D 4.2 4.57 0.165 0.180 d1 2.54 0.100 d2 0.56 0.022 E 7.37 8.38 0.290 0.330 e 1.27 0.050 e3 5.08 0.200 F 0.38 0.015 G 0.101 0.004 M 1.27 0.050 M1 1.14 0.045 P027A 10/11 M54/M74HC107 Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express written approval of SGS-THOMSON Microelectonics. 1994 SGS-THOMSON Microelectronics - All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A 11/11