Optoway GBS-9040FG 1 *********************************************************************************************************************************************************************** GBS-9040FG (RoHS Compliant) 5V / 1310 nm / 2.125 Gb/s Signle-Mode Gigabit Interface Converter (GBIC) ********************************************************************************************************************************************************************** FEATURES DESCRIPTION l Up to 2.5 Gbps Bi-directional Data Links l Compliant with 1X / 2X Fibre Channel FC-PI 13.0 l Compliant with Gigabit Interface Converter (GBIC) Specification Rev. 5.5 l 1310 nm DFB Laser Transmitter l 23 dB Power Budget at Least l Hot Pluggable module with Duplex SC Connector l Multi-rate Operation for 2.5 / 2.125 / 1.062 / 1.25 Gbps l Link Distance up to 40 km l SCA-2 Host Connector l Single +5 V Power Supply The GBS-9040FG series optical transceivers meet the Gigabit Interface Converter (GBIC) specification Rev. 5.5. It satisfies the optical interface specifications defined in IEEE 802.3z Drift 5.0 1000 BASE-LX for Gigabit Ethernet and 1x / 2x Fibre Channel FC-PI 13.0. This module is designed for single-mode fiber and operates at a nominal wavelength of 1310 nm. A guaranteed minimum optical link budget of 23 dB is offered which can correspond to a link distance of over 40 km (assuming worst case fiber loss of 0.45 dB/km). The transmitter section uses a multiple quantum well 1310 nm DFB laser and is a class 1 laser compliant according to International Safety Standard IEC 60825. The receiver section uses an integrated InGaAs detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC. A PECL input / output logic interface is used. TTL RX-LOS output simplifies interface to external circuitry. A 20-pin SCA-2 host connector is used to connect the converter to the host system. l RoHS Compliant l Differential PECL Inputs and Outputs l TTL RX-LOS Output l Class 1 Laser International Safety Standard IEC 60825 Compliant APPLICATIONS LASER SAFETY l Switch to Switch Interface l High Speed Interface for File Servers l Data Storage l Dual Rate 1.06 / 2.125 Gb/s Fibre Channel This single mode transceiver is a Class 1 laser product. It complies with IEC 60825 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated within the specified temperature and voltage limits. The optical ports of the module shall be terminated with an optical connector or with a dust plug. ORDER INFORMATION P/No. GBS-9040F Bit Rate (Gb/s) 2.125/1.063 Distance (km) 40 FC-PI 200/100 Wavelength (nm) 1310 Package Temp. (oC) 0 to 70 SC GBIC TX Power (dBm) 5 to 0 RX Sens. (dBm) -23 RoHS Compliant Yes Absolute Maximum Ratings Parameter Storage Temperature Operating Temperature Power Supply Voltage Input Voltage Symbol Tstg Topr Vcc --- Min -40 -5 -0.5 -0.5 Max 85 70 6 Vcc Units o C o C V V Notes Air flow 1m/sec Recommended Operating Conditions Parameter Power Supply Voltage Power Supply Current Symbol Vcc ITX + IRX Min 4.75 Operating Temperature Data Rate Topr 0 Fiber Length on 9/125 µm SMF Typ 5 200 1.0625 / 1.25 2.125 / 2.5 40 Max 5.25 300 70 2.5 Units V mA Conditions Reference to GND. o C Gb/s Air flow 1m/sec km @1.0625 /2.125 Gb/s *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 12/1/2005 V2.0 Optoway GBS-9040FG 2 *********************************************************************************************************************************************************************** Transmitter Specifications (0 oC < Topr < 70 oC, 4.75 V < Vcc < 5.25V) Parameter Optical Optical Transmit Power Output Center Wavelength Output Spectrum Width Extinction Ratio Optical Rise Time Optical Fall Time Pout TX_Disable Asserted Electrical Differential Input Voltage Transmit Fault Load Transmit Fault Output-Low Transmit Fault Output-High TX-Disable Input - Low TX-Disable Input - High TX-Disable Assert Time TX-Disable Negate Time Time to initialize, includes reset of TX-FAULT TX FAULT from fault to assertion TX-Disable time to start reset Symbol Min Typ Max Units Notes Po λ ∆λ ER tr tf POFF 0 1280 --1310 --- 5 1335 1 --150 150 -35 dBm nm nm dB ps ps dBm 1 VIH - VIL TX-FAULTLOAD VTX-FAULT-L VTX-FAULT-H V TX-DISABLE-L V TX-DISABLE-H t_off t-on t-int 0.65 4.7 0.0 Vcc – 0.5 0 2.0 2.0 10 0.5 Vcc + 0.3 0.8 Vcc + 0.3 10 1 300 Vp-p kΩ V V V V µs ms ms 100 µs 9 t-fault t-reset -20 dB Width 20% to 80% value 20% to 80% value 2 µs 10 1. Output power is power coupled into a 9/125 µm SM fiber. 2. Pull-up resistor on host Vcc. Receiver Specifications (0oC < Topr < 70oC, 4.75 V < Vcc < 5.25V) Parameter Symbol Min Typ Max Units Notes -23 --- 3 3 1600 -23 --- dBm dBm dB nm dBm dBm 2.0 0.35 0.35 10 0.5 Vcc 100 100 Vp-p ns ns kΩ V V µs µs Optical Sensitivity @2.125Gb/s @ BER=10-12 Maximum Input Power Signal detect – Hysteresis Wavelength of Operation RX-LOS – Asserted RX-LOS – Deasserted Electrical Differential Output Voltage Data Output Rise Time Data Output Fall Time Receiver Loss of Light Load Loss of Signal Output Voltage --- Low Loss of Signal Output Voltage --- High Loss of Signal Assert Time (off to on) Loss of Signal Deassert Time (on to off) Sens Pin Pa Pd ±RX-DAT TrRX-DAT TfRX-DAT RX-LOSLOAD RX-LOSL RX-LOSH TA,RX-LOS TD,RX-LOS -3 1.0 1200 ---33 --------- 0.37 4.7 0 2.4 Transition: low to high Transition: high to low 4 3. Minimum sensitivity and saturation levels at BER=1E-12 for a 2 7-1 PRBS. 4. Pull-up resistor on host Vcc. *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 12/1/2005 V2.0 Optoway GBS-9040FG 3 *********************************************************************************************************************************************************************** PIN ASSIGNMENT PIN Signal Name Sequence Description Receiver Loss of Signal, logic high, open collector compatible, 4.7K to 10K ohm pull-up to VCCT on host Receiver Ground Receiver Ground TTL Low SCL Serial Clock Signal SDA Serial Data Signal Transmitter Disable, logic high, open collector compatible Transmitter Ground Transmitter Ground Transmitter Fault, logic high, open collector compatible, 4.7K to 10K ohm pull-up to V CCT on GBIC Receiver Ground Receiver Data Bar, Differential PECL, AC coupled Receiver Data, Differential PECL, AC coupled Receiver Ground Receiver +5V Supply Transmitter +5V Supply Transmitter Ground Transmitter Data, Differential PECL, AC coupled Transmitter Data Bar, Differential PECL, AC coupled Transmitter Ground 1 RX-LOS 2 2 3 4 5 6 7 8 9 10 RGND RGND MOD-DEF(0) MOD-DEF(1) MOD-DEF(2) TX-DIABLE TGND TGND TX-FAULT 2 2 2 2 2 2 2 2 2 11 12 13 14 15 16 17 18 19 20 RGND -RX-DAT +RX-DAT RGND VCCR VCCT TGND +TX-DAT -TX-DAT TGND 1 1 1 1 2 2 1 1 1 1 A sequence value of 1 indicates that the signal is in the first group to engage during plugging of a module. A sequence value of 2 indicates that the signal is the second and last group. The two guide pins on the connector are electrically connected to the transceiver circuit ground. These two guide pins make contact with circuit prior to sequence 1 signals. Module Definition Module Definition 4 MOD-DEF(0) PIN 4 MOD-DEF (1) PIN 5 MOD-DEF (2) PIN 6 Interpretation by Host TTL Low SCL SDA Serial module definition protocol Module Definition 4 specifies a serial definition protocol. For this definition, upon power up, MOD-DEF(1:2) appear as no connector (NC) and MOD-DEF(0) is TTL LOW. When the host system detects this condition, it activates the serial protocol. The protocol uses the 2-wire serial CMOS E 2PROM protocol of the ATMEL AT24C01A/02/04 family of components. *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 12/1/2005 V2.0 Optoway GBS-9040FG 4 *********************************************************************************************************************************************************************** PACKAGE DIAGRAM Units in mm Note: Specifications subject to change without notice. *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 12/1/2005 V2.0