TI1 ADC128S052CIMT 8-channel, 200 ksps to 500 ksps, 12-bit a/d converter Datasheet

Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
ADC128S052, ADC128S052-Q1
SNAS333E – AUGUST 2005 – REVISED DECEMBER 2015
ADC128S052, ADC128S052-Q1 8-Channel, 200 kSPS to 500 kSPS, 12-Bit A/D Converter
1 Features
3 Description
•
•
The ADC128S052x device is a low-power, eightchannel CMOS 12-bit analog-to-digital converter
specified for conversion throughput rates of
200 kSPS to 500 kSPS. The converter is based on a
successive-approximation register architecture with
an internal track-and-hold circuit. It can be configured
to accept up to eight input signals at inputs IN0
through IN7.
1
•
•
•
•
•
•
•
•
•
Qualified for Automotive Applications
AEC-Q100 Qualified With the Following Results:
– Device Temperature Grade 1: –40°C to
+125°C Ambient Operating Temperature
Range
Eight Input Channels
Variable Power Management
Independent Analog and Digital Supplies
Compatible With SPI™, QSPI™, MICROWIRE,
and DSP
Packaged in 16-Pin TSSOP
Conversion Rate 200 kSPS to 500 kSPS
DNL (VA = VD = 5 V) + 1.3 or −0.9 LSB
(Maximum)
INL (VA = VD = 5 V) ±1 LSB (Maximum)
Power Consumption
– 3-V Supply 1.6 mW (Typical)
– 5-V Supply 8.7 mW (Typical)
The output serial data is straight binary and is
compatible with several standards, such as SPI,
QSPI, MICROWIRE, and many common DSP serial
interfaces.
The ADC128S052x may be operated with
independent analog and digital supplies. The analog
supply (VA) can range from 2.7 V to 5.25 V, and the
digital supply (VD) can range from 2.7 V to VA.
Normal power consumption using a 3-V or
5-V supply is 1.6 mW and 8.7 mW, respectively. The
power-down feature reduces the power consumption
to 0.06 µW using a 3-V supply and 0.25 µW using a
5-V supply.
The ADC128S052x is packaged in a 16-pin TSSOP
package. The ADC128S052 is ensured over the
extended industrial temperature range of −40°C to
+105°C while the ADC128S052-Q1 is ensured to an
AECQ100 Grade-1 automotive temperature range of
−40°C to +125°C.
2 Applications
•
•
•
•
•
Automotive Navigation
Portable Systems
Medical Instruments
Mobile Communications
Instrumentation and Control Systems
Device Information(1)
PART NUMBER
ADC128S052,
ADC128S052-Q1
PACKAGE
TSSOP (16)
BODY SIZE (NOM)
4.40 mm × 5.00 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Simplified Schematic
VA is used as the Reference
for the ADC
“Analog” Supply Rail
VD can be set independently
of VA
VA
VIN7
“Digital” Supply Rail
VD
IN7
IN6
IN4
VIN3
CONTROLLER
IN5
SAR
ADC
IN3
4-wire SPI
MCU
IN2
IN1
VIN0
IN0
AGND
DGND
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
ADC128S052, ADC128S052-Q1
SNAS333E – AUGUST 2005 – REVISED DECEMBER 2015
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
4
4
4
5
5
5
8
9
Absolute Maximum Ratings .....................................
ESD Ratings – Commercial ......................................
ESD Ratings – Automotive .......................................
Recommended Operating Conditions ......................
Thermal Information ..................................................
Electrical Characteristics ..........................................
Timing Specifications ...............................................
Typical Characteristics ..............................................
Detailed Description ............................................ 15
7.1 Overview ................................................................
7.2 Functional Block Diagram .......................................
7.3 Feature Description.................................................
7.4 Device Functional Modes........................................
15
15
15
16
7.5 Programming........................................................... 17
7.6 Register Maps ......................................................... 18
8
Application and Implementation ........................ 19
8.1 Application Information............................................ 19
8.2 Typical Application ................................................. 20
9
Power Supply Recommendations...................... 22
9.1 Power Supply Sequence......................................... 22
9.2 Power Supply Noise Considerations....................... 22
10 Layout................................................................... 23
10.1 Layout Guidelines ................................................. 23
10.2 Layout Example .................................................... 23
11 Device and Documentation Support ................. 24
11.1
11.2
11.3
11.4
11.5
11.6
Device Support ....................................................
Related Links ........................................................
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
24
25
26
26
26
26
12 Mechanical, Packaging, and Orderable
Information ........................................................... 26
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision D (March 2013) to Revision E
•
Page
Added Device Information table, ESD Ratings table, Thermal Information table, Feature Description section, Device
Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout
section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section. ..... 1
Changes from Revision C (March 2013) to Revision D
•
2
Page
Changed layout of National Data Sheet to TI format ........................................................................................................... 23
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: ADC128S052 ADC128S052-Q1
ADC128S052, ADC128S052-Q1
www.ti.com
SNAS333E – AUGUST 2005 – REVISED DECEMBER 2015
5 Pin Configuration and Functions
PW Package
16-Pin TSSOP
Top View
CS
1
16
SCLK
VA
2
15
DOUT
AGND
3
14
DIN
IN0
4
13
VD
IN1
5
12
DGND
ADC128S052
IN2
6
11
IN7
IN3
7
10
IN6
IN4
8
9
IN5
Pin Functions
PIN
NO.
NAME
TYPE
DESCRIPTION
1
CS
Digital I/O
Chip select. On the falling edge of CS, a conversion process begins. Conversions continue
as long as CS is held low.
2
VA
Power
Supply
Positive analog supply pin. This voltage is also used as the reference voltage. This pin must
be connected to a quiet 2.7-V to 5.25-V source and bypassed to GND with 1-µF and 0.1-µF
monolithic ceramic capacitors located within 1 cm of the power pin.
3
AGND
Power
Supply
The ground return for the analog supply and signals.
IN0 to IN7
Analog I/O
12
DGND
Power
Supply
The ground return for the digital supply and signals.
13
VD
Power
Supply
Positive digital supply pin. This pin must be connected to a 2.7-V to VA supply, and bypassed
to GND with a 0.1-µF monolithic ceramic capacitor located within 1 cm of the power pin.
14
DIN
Digital I/O
Digital data input. The control register of the ADC128S052 is loaded through this pin on
rising edges of the SCLK pin.
15
DOUT
Digital I/O
Digital data output. The output samples are clocked out of this pin on the falling edges of the
SCLK pin.
16
SCLK
Digital I/O
Digital clock input. The ensured performance range of frequencies for this input is
3.2 MHz to 8 MHz. This clock directly controls the conversion and readout processes.
4
5
6
7
8
Analog inputs. These signals can range from 0 V to VREF.
9
10
11
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: ADC128S052 ADC128S052-Q1
Submit Documentation Feedback
3
ADC128S052, ADC128S052-Q1
SNAS333E – AUGUST 2005 – REVISED DECEMBER 2015
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
See
(1) (2) (3)
MIN
MAX
UNIT
Analog Supply Voltage VA
–0.3
6.5
V
Digital Supply Voltage VD
–0.3
VA + 0.3, max 6.5
V
Voltage on Any Pin to GND
–0.3
VA + 0.3
V
±10
mA
±20
mA
+150
°C
150
°C
Input Current at Any Pin (4)
Package Input Current (4)
Power Dissipation at TA = 25°C
See
Junction Temperature
−65
Storage Temperature, Tstg
(1)
(2)
(3)
(4)
(5)
(5)
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
If Military/Aerospace specified devices are required, contact the TI Sales Office/Distributors for availability and specifications.
For soldering specifications: see product folder at www.ti.com and SNOA549.
When the input voltage at any pin exceeds the power supplies (that is, VIN < AGND or VIN > VA or VD), the current at that pin must be
limited to 10 mA. The 20-mA maximum package input current rating limits the number of pins that can safely exceed the power supplies
with an input current of 10 mA to two.
The absolute maximum junction temperature (TJMAX) for this device is 150°C. The maximum allowable power dissipation is dictated by
TJMAX, the junction-to-ambient thermal resistance (RθJA), and the ambient temperature (TA), and can be calculated using the formula
PDMAX = (TJMAX − TA)/RθJA. In the 16-pin TSSOP, RθJA is 110°C/W, so PDMAX = 1,200 mW at 25°C and 625 mW at the maximum
operating ambient temperature of 105°C. Note that the power consumption of this device under normal operation is a maximum of
12 mW. The values for maximum power dissipation listed above is reached only when the ADC128S052 is operated in a severe fault
condition (for example, when input or output pins are driven beyond the power supply voltages, or the power supply polarity is reversed).
Such conditions must always be avoided.
6.2 ESD Ratings – Commercial
VALUE
V(ESD)
(1)
(2)
(3)
Electrostatic
discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) (2)
±2500
Machine model (MM) (3)
±250
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
Human body model is a 100-pF capacitor discharged through a 1.5-kΩ resistor.
Machine model is a 220-pF discharged through ZERO Ω.
6.3 ESD Ratings – Automotive
VALUE
V(ESD)
(1)
4
Electrostatic
discharge
Human-body model (HBM), per AEC Q100-002 (1)
±2500
Charged-device model (CDM), per AEC Q100-011
±250
UNIT
V
AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: ADC128S052 ADC128S052-Q1
ADC128S052, ADC128S052-Q1
www.ti.com
SNAS333E – AUGUST 2005 – REVISED DECEMBER 2015
6.4 Recommended Operating Conditions
(1)
See
Operating Temperature
MIN
NOM
MAX
UNIT
ADC128S052
−40
TA
105
°C
ADC128S052-Q1
−40
TA
125
°C
VA Supply Voltage
2.7
5.25
V
VD Supply Voltage
2.7
VA
V
Digital Input Voltage
0
VA
V
Analog Input Voltage
0
VA
50
1600
Clock Frequency
(1)
V
kHz
All voltages are measured with respect to GND = 0 V, unless otherwise specified.
6.5 Thermal Information
ADC128S052, ADC128S052-Q1
THERMAL METRIC
(1)
PW (TSSOP)
UNIT
16 PINS
RθJA
Junction-to-ambient thermal resistance
110
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
42
°C/W
RθJB
Junction-to-board thermal resistance
56
°C/W
ψJT
Junction-to-top characterization parameter
5
°C/W
ψJB
Junction-to-board characterization parameter
55
°C/W
(1)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
6.6 Electrical Characteristics
The following specifications apply for AGND = DGND = 0 V, fSCLK = 3.2 MHz to 8 MHz, fSAMPLE = 200 kSPS to 500 kSPS, CL =
50 pF, unless otherwise noted. Maximum and minimum limits apply for TA = TMIN to TMAX: all other limits TA = 25°C. (1)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX (2)
UNIT
STATIC CONVERTER CHARACTERISTICS
Resolution with No Missing
Codes
Integral Non-Linearity (End
Point Method)
INL
±0.3
±1
LSB
VA = VD = 5 V
±0.4
±1
LSB
0.3
0.9
LSB
Differential Non-Linearity
VA = VD = 5 V
VOFF
Offset Error
OEM
Offset Error Match
FSE
Full Scale Error
FSEM
(1)
(2)
Full Scale Error Match
Bits
VA = VD = 3 V
VA = VD = 3 V
DNL
12
−0.7
−0.2
−0.9
−0.4
0.6
VA = VD = 3 V
LSB
1.3
LSB
LSB
0.8
±2.3
LSB
VA = VD = 5 V
1.2
±2.3
LSB
VA = VD = 3 V
±0.05
±1.5
LSB
VA = VD = 5 V
±0.2
±1.5
LSB
VA = VD = 3 V
0.6
±2.0
LSB
VA = VD = 5 V
0.3
±2.0
LSB
VA = VD = 3 V
±0.05
±1.5
LSB
VA = VD = 5 V
±0.2
±1.5
LSB
Data sheet minimum and maximum specification limits are ensured by design, test, or statistical analysis.
Tested limits are ensured to TI's AOQL (Average Outgoing Quality Level).
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: ADC128S052 ADC128S052-Q1
Submit Documentation Feedback
5
ADC128S052, ADC128S052-Q1
SNAS333E – AUGUST 2005 – REVISED DECEMBER 2015
www.ti.com
Electrical Characteristics (continued)
The following specifications apply for AGND = DGND = 0 V, fSCLK = 3.2 MHz to 8 MHz, fSAMPLE = 200 kSPS to 500 kSPS, CL =
50 pF, unless otherwise noted. Maximum and minimum limits apply for TA = TMIN to TMAX: all other limits TA = 25°C.(1)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX (2)
UNIT
DYNAMIC CONVERTER CHARACTERISTICS
FPBW
SINAD
SNR
THD
SFDR
ENOB
ISO
Full Power Bandwidth (−3 dB)
Signal-to-Noise Plus Distortion
Ratio
Signal-to-Noise Ratio
Total Harmonic Distortion
Spurious-Free Dynamic Range
Effective Number of Bits
Channel-to-Channel Isolation
Intermodulation Distortion,
Second Order Terms
IMD
Intermodulation Distortion, Third
Order Terms
VA = VD = 3 V
8
MHz
VA = VD = 5 V
11
MHz
VA = VD = 3 V,
fIN = 40.2 kHz, −0.02 dBFS
70
73
dB
VA = VD = 5 V,
fIN = 40.2 kHz, −0.02 dBFS
70
73
dB
VA = VD = 3 V,
fIN = 40.2 kHz, −0.02 dBFS
70.8
73
dB
VA = VD = 5 V,
fIN = 40.2 kHz, −0.02 dBFS
70.8
73
dB
VA = VD = 3 V,
fIN = 40.2 kHz, −0.02 dBFS
−90
−74
dB
VA = VD = 5 V,
fIN = 40.2 kHz, −0.02 dBFS
−89
−74
dB
VA = VD = 3 V,
fIN = 40.2 kHz, −0.02 dBFS
75
92
dB
VA = VD = 5 V,
fIN = 40.2 kHz, −0.02 dBFS
75
91
dB
VA = VD = 3 V,
fIN = 40.2 kHz
11.3
11.8
Bits
VA = VD = 5 V,
fIN = 40.2 kHz, −0.02 dBFS
11.3
11.8
Bits
VA = VD = 3 V,
fIN = 20 kHz
81
dB
VA = VD = 5 V,
fIN = 20 kHz, −0.02 dBFS
81
dB
VA = VD = 3 V,
fa = 19.5 kHz, fb = 20.5 kHz
−98
dB
VA = VD = 5 V,
fa = 19.5 kHz, fb = 20.5 kHz
−91
dB
VA = VD = 3 V,
fa = 19.5 kHz, fb = 20.5 kHz
−89
dB
VA = VD = 5 V,
fa = 19.5 kHz, fb = 20.5 kHz
−88
dB
ANALOG INPUT CHARACTERISTICS
VIN
Input Range
IDCL
DC Leakage Current
CINA
Input Capacitance
0
VA
V
±1
µA
Track Mode
33
pF
Hold Mode
3
pF
DIGITAL INPUT CHARACTERISTICS
VA = VD = 2.7 V to 3.6 V
2.1
VA = VD = 4.75 V to 5.25 V
2.4
VIH
Input High Voltage
VIL
Input Low Voltage
VA = VD = 2.7 V to 5.25 V
IIN
Input Current
VIN = 0 V or VD
CIND
Digital Input Capacitance
6
Submit Documentation Feedback
V
V
0.8
V
±0.01
±1
µA
2
4
pF
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: ADC128S052 ADC128S052-Q1
ADC128S052, ADC128S052-Q1
www.ti.com
SNAS333E – AUGUST 2005 – REVISED DECEMBER 2015
Electrical Characteristics (continued)
The following specifications apply for AGND = DGND = 0 V, fSCLK = 3.2 MHz to 8 MHz, fSAMPLE = 200 kSPS to 500 kSPS, CL =
50 pF, unless otherwise noted. Maximum and minimum limits apply for TA = TMIN to TMAX: all other limits TA = 25°C.(1)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX (2)
UNIT
DIGITAL OUTPUT CHARACTERISTICS
VOH
Output High Voltage
ISOURCE = 200 µA,
VA = VD = 2.7 V to 5.25 V
VOL
Output Low Voltage
ISINK = 200 µA to 1.0 mA,
VA = VD = 2.7 V to 5.25 V
0.4
V
IOZH,
IOZL
Hi-Impedance Output Leakage
Current
VA = VD = 2.7 V to 5.25 V
±1
µA
COUT
Hi-Impedance Output
Capacitance (1)
4
pF
VD − 0.5
V
2
Output Coding
Straight (Natural) Binary
POWER SUPPLY CHARACTERISTICS (CL = 10 pF)
VA, VD
Analog and Digital Supply
Voltages
Total Supply Current
Normal Mode ( CS low)
IA + ID
Total Supply Current
Shutdown Mode (CS high)
Power Consumption
Normal Mode ( CS low)
PC
Power Consumption
Shutdown Mode (CS high)
VA ≥ VD
2.7
5.25
V
VA = VD = 2.7 V to 3.6 V,
fSAMPLE = 500 kSPS, fIN = 40 kHz
0.54
1.2
mA
VA = VD = 4.75 V to 5.25 V,
fSAMPLE = 500 kSPS, fIN = 40 kHz
1.74
2.6
mA
VA = VD = 2.7 V to 3.6 V,
fSCLK = 0 kSPS
20
nA
VA = VD = 4.75 V to 5.25 V,
fSCLK = 0 kSPS
50
nA
VA = VD = 3 V
fSAMPLE = 500 kSPS, fIN = 40 kHz
1.6
3.6
mW
VA = VD = 5.0 V
fSAMPLE = 500 kSPS, fIN = 40 kHz
8.7
13.0
mW
VA = VD = 3 V
fSCLK = 0 kSPS
0.06
µW
VA = VD = 5 V
fSCLK = 0 kSPS
0.25
µW
0.8
MHz
AC ELECTRICAL CHARACTERISTICS
fSCLKMI
N
Minimum Clock Frequency
VA = VD = 2.7 V to 5.25 V
fSCLK
Maximum Clock Frequency
VA = VD = 2.7 V to 5.25 V
fS
Sample Rate
Continuous Mode
VA = VD = 2.7 V to 5.25 V
tCONVER
Conversion (Hold) Time
VA = VD = 2.7 V to 5.25 V
DC
SCLK Duty Cycle
VA = VD = 2.7 V to 5.25 V
tACQ
Acquisition (Track) Time
VA = VD = 2.7 V to 5.25 V
Throughput Time
Acquisition Time + Conversion Time
VA = VD = 2.7 V to 5.25 V
Aperture Delay
VA = VD = 2.7 V to 5.25 V
T
tAD
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: ADC128S052 ADC128S052-Q1
3.2
16
200
50
1000
40%
8
MHz
kSPS
500
kSPS
13
SCLK
cycles
30%
70%
60%
3
SCLK
cycles
16
SCLK
cycles
4
Submit Documentation Feedback
ns
7
ADC128S052, ADC128S052-Q1
SNAS333E – AUGUST 2005 – REVISED DECEMBER 2015
www.ti.com
6.7 Timing Specifications
The following specifications apply for VA = VD = 2.7 V to 5.25 V, AGND = DGND = 0 V, fSCLK = 3.2 MHz to 8 MHz, fSAMPLE =
200 kSPS to 500 kSPS, and CL = 50 pF. Maximum and minimum limits apply for TA = TMIN to TMAX; all other limits TA = 25°C.
See Figure 1, Figure 2, and Figure 3.
MAX (1)
MIN
NOM
tCSH
CS Hold Time after SCLK
Rising Edge
10
0
ns
tCSS
CS Set-up Time prior to SCLK
Rising Edge
10
4.5
ns
tEN
CS Falling Edge to DOUT
enabled
tDACC
DOUT Access Time after SCLK
Falling Edge
tDHLD
DOUT Hold Time after SCLK
Falling Edge
tDS
DIN Set-up Time prior to SCLK
Rising Edge
tDH
DIN Hold Time after SCLK
Rising Edge
tCH
SCLK High Time
0.4 × tSCLK
tCL
SCLK Low Time
0.4 × tSCLK
CS Rising Edge to DOUT HighImpedance
tDIS
(1)
UNIT
5
30
ns
17
27
ns
4
ns
10
3
ns
10
3
ns
ns
ns
DOUT falling
2.4
20
ns
DOUT rising
0.9
20
ns
Tested limits are ensured to TI's AOQL (Average Outgoing Quality Level).
Power
Down
Power Up
Track
Power Up
Hold
Track
Hold
CS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1
16
2
3
4
5
6
7
8
SCLK
Control register
DIN
DOUT
ADD2
ADD1
ADD0
ADD2
DB11 DB10 DB9
FOUR ZEROS
DB8
DB7
DB6
DB5
DB4
DB3
DB2
DB1
FOUR ZEROS
DB0
ADD1
ADD0
DB11 DB10 DB9
Figure 1. ADC128S052 Operational Timing Diagram
CS
tCONVERT
tACQ
tCH
SCLK
1
2
3
4
5
6
7
tCL
tEN
DOUT
8
16
tDACC
DB11
FOUR ZEROS
DB10
tDHLD
DB9
DB8
tDIS
DB1
DB0
tDH
tDS
DIN
DONTC
DONTC
ADD2
ADD1
ADD0
DONTC
DONTC
DONTC
Figure 2. ADC128S052 Serial Timing Diagram
8
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: ADC128S052 ADC128S052-Q1
ADC128S052, ADC128S052-Q1
www.ti.com
SNAS333E – AUGUST 2005 – REVISED DECEMBER 2015
SCLK
tCSS
CS
tCSH
CS
Figure 3. SCLK and CS Timing Parameters
6.8 Typical Characteristics
TA = 25°C, fSAMPLE = 500 kSPS, fSCLK = 8 MHz, fIN = 40.2 kHz unless otherwise stated
Figure 4. DNL
Figure 5. DNL
Figure 6. INL
Figure 7. INL
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: ADC128S052 ADC128S052-Q1
Submit Documentation Feedback
9
ADC128S052, ADC128S052-Q1
SNAS333E – AUGUST 2005 – REVISED DECEMBER 2015
www.ti.com
Typical Characteristics (continued)
TA = 25°C, fSAMPLE = 500 kSPS, fSCLK = 8 MHz, fIN = 40.2 kHz unless otherwise stated
Figure 8. DNL vs Supply
Figure 9. INL vs Supply
Figure 10. SNR vs Supply
Figure 11. THD vs Supply
VA = 5 V
Figure 12. ENOB vs Supply
10
Submit Documentation Feedback
Figure 13. DNL vs VD
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: ADC128S052 ADC128S052-Q1
ADC128S052, ADC128S052-Q1
www.ti.com
SNAS333E – AUGUST 2005 – REVISED DECEMBER 2015
Typical Characteristics (continued)
TA = 25°C, fSAMPLE = 500 kSPS, fSCLK = 8 MHz, fIN = 40.2 kHz unless otherwise stated
VA = 5 V
Figure 14. INL vs VD
Figure 15. DNL vs SCLK Duty Cycle
Figure 16. INL vs SCLK Duty Cycle
Figure 17. SNR vs SCLK Duty Cycle
Figure 18. THD vs SCLK Duty Cycle
Figure 19. ENOB vs SCLK Duty Cycle
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: ADC128S052 ADC128S052-Q1
Submit Documentation Feedback
11
ADC128S052, ADC128S052-Q1
SNAS333E – AUGUST 2005 – REVISED DECEMBER 2015
www.ti.com
Typical Characteristics (continued)
TA = 25°C, fSAMPLE = 500 kSPS, fSCLK = 8 MHz, fIN = 40.2 kHz unless otherwise stated
12
Figure 20. DNL vs SCLK
Figure 21. INL vs SCLK
Figure 22. SNR vs SCLK
Figure 23. THD vs SCLK
Figure 24. ENOB vs SCLK
Figure 25. DNL vs Temperature
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: ADC128S052 ADC128S052-Q1
ADC128S052, ADC128S052-Q1
www.ti.com
SNAS333E – AUGUST 2005 – REVISED DECEMBER 2015
Typical Characteristics (continued)
TA = 25°C, fSAMPLE = 500 kSPS, fSCLK = 8 MHz, fIN = 40.2 kHz unless otherwise stated
Figure 26. INL vs Temperature
Figure 27. SNR vs Temperature
Figure 28. THD vs Temperature
Figure 29. ENOB vs Temperature
Figure 30. SNR vs Input Frequency
Figure 31. THD vs Input Frequency
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: ADC128S052 ADC128S052-Q1
Submit Documentation Feedback
13
ADC128S052, ADC128S052-Q1
SNAS333E – AUGUST 2005 – REVISED DECEMBER 2015
www.ti.com
Typical Characteristics (continued)
TA = 25°C, fSAMPLE = 500 kSPS, fSCLK = 8 MHz, fIN = 40.2 kHz unless otherwise stated
Figure 32. ENOB vs Input Frequency
14
Submit Documentation Feedback
Figure 33. Power Consumption vs SCLK
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: ADC128S052 ADC128S052-Q1
ADC128S052, ADC128S052-Q1
www.ti.com
SNAS333E – AUGUST 2005 – REVISED DECEMBER 2015
7 Detailed Description
7.1
Overview
The ADC128S052x is a successive-approximation analog-to-digital converter designed around a chargeredistribution digital-to-analog converter. For the remainder of this document, ADC128S052x is abbreviated to
ADC128S052.
7.2 Functional Block Diagram
IN0
.
.
.
MUX
T/H
12-BIT
SUCCESSIVE
APPROXIMATION
ADC
VA
AGND
AGND
IN7
VD
SCLK
ADC128S052
CONTROL
LOGIC
CS
DIN
DOUT
DGND
7.3 Feature Description
7.3.1 Operation
Simplified schematics of the ADC128S052 in both track and hold operation are shown in Figure 34 and
Figure 35, respectively. In Figure 34, the ADC128S052 is in track mode: switch SW1 connects the sampling
capacitor to one of eight analog input channels through the multiplexer, and SW2 balances the comparator
inputs. The ADC128S052 is in this state for the first three SCLK cycles after CS is brought low.
Figure 35 shows the ADC128S052 in hold mode: switch SW1 connects the sampling capacitor to ground,
maintaining the sampled voltage, and switch SW2 unbalances the comparator. The control logic then instructs
the charge-redistribution DAC to add or subtract fixed amounts of charge to or from the sampling capacitor until
the comparator is balanced. When the comparator is balanced, the digital word supplied to the DAC is the digital
representation of the analog input voltage. The ADC128S052 is in this state for the last thirteen SCLK cycles
after CS is brought low.
IN0
CHARGE
REDISTRIBUTION
DAC
MUX
SAMPLING
CAPACITOR
SW1
IN7
SW2
+
-
CONTROL
LOGIC
AGND
VA /2
Figure 34. ADC128S052 in Track Mode
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: ADC128S052 ADC128S052-Q1
Submit Documentation Feedback
15
ADC128S052, ADC128S052-Q1
SNAS333E – AUGUST 2005 – REVISED DECEMBER 2015
www.ti.com
Feature Description (continued)
IN0
CHARGE
REDISTRIBUTION
DAC
MUX
SAMPLING
CAPACITOR
+
SW1
IN7
SW2
CONTROL
LOGIC
-
AGND
VA /2
Figure 35. ADC128S052 in Hold Mode
7.3.2 Transfer Function
The output format of the ADC128S052 is straight binary. Code transitions occur midway between successive
integer LSB values. The LSB width for the ADC128S052 is VA / 4096. The ideal transfer characteristic is shown
in Figure 36. The transition from an output code of 0000 0000 0000 to a code of 0000 0000 0001 is at 1/2 LSB,
or a voltage of VA / 8192. Other code transitions occur at steps of one LSB.
111...111
ADC CODE
111...110
111...000
|
|
1LSB = VA/4096
011...111
000...010
|
000...001
000...000
0V
0.5LSB
ANALOG INPUT
+VA - 1.5LSB
Figure 36. Ideal Transfer Characteristic
7.4 Device Functional Modes
The ADC128S052 is fully powered up whenever CS is low and fully powered down whenever CS is high, with
one exception. If operating in continuous conversion mode, the ADC128S052 automatically enters power-down
mode between the SCLK 16th falling edge of a conversion and the SCLK 1st falling edge of the subsequent
conversion (see Figure 1).
In continuous conversion mode, the ADC128S052 can perform multiple conversions back-to-back. Each
conversion requires 16 SCLK cycles, and the ADC128S052 performs conversions continuously as long as CS is
held low. Continuous mode offers maximum throughput.
16
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: ADC128S052 ADC128S052-Q1
ADC128S052, ADC128S052-Q1
www.ti.com
SNAS333E – AUGUST 2005 – REVISED DECEMBER 2015
Device Functional Modes (continued)
In burst mode, the user may trade off throughput for power consumption by performing fewer conversions per
unit time. This means spending more time in power-down mode and less time in normal mode. By utilizing this
technique, the user can achieve very low sample rates while still utilizing an SCLK frequency within the electrical
specifications. Figure 33 in the Typical Characteristics section shows the typical power consumption of the
ADC128S052. To calculate the power consumption (PC), simply multiply the fraction of time spent in the normal
mode (tN) by the normal mode power consumption (PN), and add the fraction of time spent in shutdown mode (tS)
multiplied by the shutdown mode power consumption (PS) as shown in Equation 1.
PC =
tS
tN
x PN +
x PS
tN + t S
tN + t S
(1)
7.5 Programming
7.5.1 Serial Interface
Figure 1 shows a operational timing diagram, and Figure 2 shows a serial interface timing diagram for the
ADC128S052. CS (chip select) initiates conversions and frames the serial data transfers. SCLK (serial clock)
controls both the conversion process and the timing of serial data. DOUT is the serial data output pin, where a
conversion result is sent as a serial data stream, MSB first. Data to be written to the control register of the device
is placed on DIN, the serial data input pin. New data is written to DIN with each conversion.
A serial frame is initiated on the falling edge of CS and ends on the rising edge of CS. Each frame must contain
an integer multiple of 16 rising SCLK edges. The ADC's DOUT pin is in a high impedance state when CS is high
and is active when CS is low. Thus, CS acts as an output enable. Similarly, SCLK is internally gated off when CS
is brought high.
During the first 3 cycles of SCLK, the ADC is in the track mode, acquiring the input voltage. For the next 13
SCLK cycles the conversion is accomplished, and the data is clocked out. SCLK falling edges 1 through 4 clock
out leading zeros while falling edges 5 through 16 clock out the conversion result, MSB first. If there is more than
one conversion in a frame (continuous conversion mode), the ADC re-enters the track mode on the falling edge
of SCLK after the N × 16th rising edge of SCLK and re-enter the hold/convert mode on the N × 16 + 4th falling
edge of SCLK. N is an integer value.
The ADC128S052 enters track mode under three different conditions. In Figure 1, CS goes low with SCLK high,
and the ADC enters track mode on the first falling edge of SCLK. In the second condition, CS goes low with
SCLK low. Under this condition, the ADC automatically enters track mode and the falling edge of CS is seen as
the first falling edge of SCLK. In the third condition, CS and SCLK go low simultaneously, and the ADC enters
track mode. While there is no timing restriction with respect to the rising edges of CS and SCLK, see Figure 3 for
setup and hold time requirements for the falling edge of CS with respect to the rising edge of SCLK.
While a conversion is in progress, the address of the next input for conversion is clocked into a control register
through the DIN pin on the first 8 rising edges of SCLK after the fall of CS. See Table 1, Table 2, Table 3.
There is no need to incorporate a power-up delay or dummy conversion as the ADC128S052 is able to acquire
the input signal to full resolution in the first conversion immediately following power up. The first conversion result
after power-up is that of IN0.
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: ADC128S052 ADC128S052-Q1
Submit Documentation Feedback
17
ADC128S052, ADC128S052-Q1
SNAS333E – AUGUST 2005 – REVISED DECEMBER 2015
www.ti.com
7.6 Register Maps
Table 1. Control Register Bits
7
6
5
4
3
2
1
0
DONTC
DONTC
ADD2
ADD1
ADD0
DONTC
DONTC
DONTC
Table 2. Control Register Bit Descriptions
BIT NO.
SYMBOL
7, 6, 2, 1, 0
DONTC
5
ADD2
4
ADD1
3
ADD0
DESCRIPTION
Don't care. The values of these bits do not affect the device.
These three bits determine which input channel is sampled and converted at the next conversion
cycle. The mapping between codes and channels is shown in Table 3.
Table 3. Input Channel Selection
18
ADD2
ADD1
ADD0
INPUT CHANNEL
0
0
0
IN0 (Default)
0
0
1
IN1
0
1
0
IN2
0
1
1
IN3
1
0
0
IN4
1
0
1
IN5
1
1
0
IN6
1
1
1
IN7
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: ADC128S052 ADC128S052-Q1
ADC128S052, ADC128S052-Q1
www.ti.com
SNAS333E – AUGUST 2005 – REVISED DECEMBER 2015
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
8.1.1 Analog Inputs
An equivalent circuit for one of the input channels of the ADC128S052 is shown in Figure 37. Diodes D1 and D2
provide ESD protection for the analog inputs. The operating range for the analog inputs is 0 V to VA. Going
beyond this range causes the ESD diodes to conduct and result in erratic operation.
The capacitor C1 in Figure 37 has a typical value of 3 pF and is mainly the package pin capacitance. Resistor R1
is the on resistance of the multiplexer and track or hold switch and is typically 500 Ω. Capacitor C2 is the
ADC128S052 sampling capacitor and is typically 30 pF. The ADC128S052 delivers best performance when
driven by a low-impedance source (less than 100 Ω). This is especially important when using the ADC128S052
to sample dynamic signals. Also important when sampling dynamic signals is a band-pass or low-pass filter
which reduces harmonics and noise in the input. These filters are often referred to as anti-aliasing filters.
VA
D1
R1
C2
30 pF
VIN
C1
3 pF
D2
Conversion Phase - Switch Open
Track Phase - Switch Closed
Figure 37. Equivalent Input Circuit
8.1.2 Digital Inputs and Outputs
The digital inputs (SCLK, CS, and DIN) of the ADC128S052 have an operating range of 0 V to VA. They are not
prone to latch-up and may be asserted before the digital supply (VD) without any risk. The digital output (DOUT)
operating range is controlled by VD. The output high voltage is VD – 0.5 V (minimum) while the output low voltage
is 0.4 V (maximum).
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: ADC128S052 ADC128S052-Q1
Submit Documentation Feedback
19
ADC128S052, ADC128S052-Q1
SNAS333E – AUGUST 2005 – REVISED DECEMBER 2015
8.2
www.ti.com
Typical Application
A typical application is shown in Figure 38. The analog supply is bypassed with a capacitor network located close
to the ADC128S052. The ADC128S052 uses the analog supply (VA) as its reference voltage, so it is very
important that VA be kept as clean as possible. Due to the low power requirements of the ADC128S052, it is also
possible to use a precision reference as a power supply.
5V
3.3V
1uF
High
Impedance
Source
+
LMV612
0.1uF
0.1uF
VA
100
1uF
VD
IN7
VDD
100
GPIOa
SCLK
100
GPIOb
CS
33n
MCU
100
Low
Impedance
Source
Schottky
Diode
(optional)
100
IN3
ADC128S102
100
DIN
GPIOd
GND
IN0
33n
GPIOc
DOUT
AGND
DGND
Figure 38. Typical Application Circuit
8.2.1 Design Requirements
A positive supply-only data acquisition system capable of digitizing signals ranging 0 to 5 V, BW = 10 kHz, and a
throughput of 125 kSPS.
The ADC128S052 has to interface to a microcontroller with the supply is set at 3.3 V.
8.2.2 Detailed Design Procedure
The signal range requirement forces the design to use 5-V analog supply at VA, analog supply. This follows from
the fact that VA is also a reference potential for the ADC.
The requirement of interfacing to the microcontroller which is powered by a 3.3-V supply, forces the choice of
3.3 V as a VD supply.
Sampling is in fact a modulation process which may result in aliasing of the input signal, if the input signal is not
adequately band limited. The maximum sampling rate of the ADC128S052 when all channels are enabled is, Fs
is calculated by Equation 2:
FSCLK
Fs =
16 ´ 8
(2)
Note that faster sampling rates can be achieved when fewer channels are sampled. Single channel can be
sampled at the maximum rate of:
FSCLK
Fs _ sin gle =
16
(3)
In order to avoid the aliasing the Nyquist criterion has to be met:
Fs
BW signal £
2
(4)
Therefore it is necessary to place anti-aliasing filters at all inputs of the ADC. These filters may be single-pole
low-pass filters. The pole locations need to satisfy, assuming all channels sampled in sequence, Equation 5 and
Equation 6:
1
FSCLK
£
p ´ R ´ C 16 ´ 8
(5)
128
R´C ³
p ´ FSCLK
(6)
20
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: ADC128S052 ADC128S052-Q1
ADC128S052, ADC128S052-Q1
www.ti.com
SNAS333E – AUGUST 2005 – REVISED DECEMBER 2015
Typical Application (continued)
With FSCLK = 16 MHz, a good choice for the single pole filter is:
• R = 100
• C = 33 nF
This reduces the input BWsignal = 48 kHz. The capacitor at the INx input of the device provides not only the
filtering of the input signal, but it also absorbs the charge kick-back from the ADC. The kick-back is the result of
the internal switches opening at the end of the acquisition period.
The VA and VD sources are already separated in this example, due to the design requirements. This also benefits
the overall performance of the ADC, as the potentially noisy VD supply does not contaminate the VA. In the same
vain, further consideration could be given to the SPI interface, especially when the master microcontroller is
capable of producing fast rising edges on the digital bus signals. Inserting small resistances in the digital signal
path may help in reducing the ground bounce, and thus improve the overall noise performance of the system.
Take care when the signal source is capable of producing voltages beyond VA. In such instances the internal
ESD diodes may start conducting. The ESD diodes are not intended as input signal clamps. To provide the
desired clamping action use Schottky diodes as shown in Figure 38.
8.2.3 Application Curve
Figure 39. Typical Performance
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: ADC128S052 ADC128S052-Q1
Submit Documentation Feedback
21
ADC128S052, ADC128S052-Q1
SNAS333E – AUGUST 2005 – REVISED DECEMBER 2015
www.ti.com
9 Power Supply Recommendations
There are three major power supply concerns with this product: power supply sequencing, power management,
and the effect of digital supply noise on the analog supply.
9.1 Power Supply Sequence
The ADC128S052 is a dual-supply device. The two supply pins share ESD resources, so exercise care to ensure
that the power is applied in the correct sequence. To avoid turning on the ESD diodes, the digital supply (VD)
cannot exceed the analog supply (VA) by more than 300 mV, not even on a transient basis. Therefore, VA must
ramp up before or concurrently with VD.
9.2 Power Supply Noise Considerations
The charging of any output load capacitance requires current from the digital supply, VD. The current pulses
required from the supply to charge the output capacitance causes voltage variations on the digital supply. If these
variations are large enough, they could degrade SNR and SINAD performance of the ADC. Furthermore, if the
analog and digital supplies are tied directly together, the noise on the digital supply is coupled directly into the
analog supply, causing greater performance degradation than would noise on the digital supply alone. Similarly,
discharging the output capacitance when the digital output goes from a logic high to a logic low dumps current
into the die substrate, which is resistive. Load discharge currents causes ground bounce noise in the substrate
that degrades noise performance if that current is large enough. The larger the output capacitance, the more
current flows through the die substrate and the greater the noise coupled into the analog channel.
The first solution for keeping digital noise out of the analog supply is to decouple the analog and digital supplies
from each other or use separate supplies for them. To keep noise out of the digital supply, keep the output load
capacitance as small as practical. If the load capacitance is greater than 50 pF, use a 100-Ω series resistor at
the ADC output, located as close to the ADC output pin as practical. This limits the charge and discharge current
of the output capacitance and improves noise performance. Because the series resistor and the load capacitor
form a low frequency pole, verify signal integrity once the series resistor has been added.
22
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: ADC128S052 ADC128S052-Q1
ADC128S052, ADC128S052-Q1
www.ti.com
SNAS333E – AUGUST 2005 – REVISED DECEMBER 2015
10 Layout
10.1 Layout Guidelines
Capacitive coupling between the noisy digital circuitry and the sensitive analog circuitry can lead to poor
performance. The solution is to keep the analog circuitry separated from the digital circuitry and the clock line as
short as possible.
Digital circuits create substantial supply and ground current transients. The logic noise generated could have
significant impact upon system noise performance. To avoid performance degradation of the ADC128S052 due
to supply noise, do not use the same supply for the ADC128S052 that is used for digital logic.
Generally, analog and digital lines must cross each other at 90° to avoid crosstalk. However, to maximize
accuracy in high resolution systems, avoid crossing analog and digital lines altogether. It is important to keep
clock lines as short as possible and isolated from ALL other lines, including other digital lines. In addition, the
clock line must also be treated as a transmission line and be properly terminated.
The analog input must be isolated from noisy signal traces to avoid coupling of spurious signals into the input.
Any external component (for example, a filter capacitor) connected between the input pins and ground of the
converter or to the reference input pin and ground must be connected to a very clean point in the ground plane.
TI recommends the use of a single, uniform ground plane and the use of split power planes. The power planes
must be located within the same board layer. All analog circuitry (input amplifiers, filters, reference components,
and so forth) must be placed over the analog power plane. All digital circuitry and I/O lines must be placed over
the digital power plane. Furthermore, all components in the reference circuitry and the input signal chain that are
connected to ground must be connected together with short traces and enter the analog ground plane at a
single, quiet point.
10.2 Layout Example
ANALOG
SUPPLY
RAIL
to analog
signal sources
CS
SCLK
VA
DOUT
AGND
DIN
IN0
VD
IN1
DGND
IN2
IN7
IN3
IN6
IN4
IN5
toMCU
“DIGITAL” SUPPLY RAIL
VIA to GROUND PLANE
GROUND PLANE
Figure 40. Layout Schematic
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: ADC128S052 ADC128S052-Q1
Submit Documentation Feedback
23
ADC128S052, ADC128S052-Q1
SNAS333E – AUGUST 2005 – REVISED DECEMBER 2015
www.ti.com
11 Device and Documentation Support
11.1 Device Support
11.1.1 Device Nomenclature
11.1.1.1 Specification Definitions
ACQUISITION TIME is the time required for the ADC to acquire the input voltage. During this time, the hold
capacitor is charged by the input voltage.
APERTURE DELAY is the time between the fourth falling edge of SCLK and the time when the input signal is
internally acquired or held for conversion.
CONVERSION TIME is the time required, after the input voltage is acquired, for the ADC to convert the input
voltage to a digital word.
CHANNEL-TO-CHANNEL ISOLATION is resistance to coupling of energy from one channel into another
channel.
CROSSTALK is the coupling of energy from one channel into another channel. This is similar to Channel-toChannel Isolation, except for the sign of the data.
DIFFERENTIAL NON-LINEARITY (DNL) is the measure of the maximum deviation from the ideal step size of 1
LSB.
DUTY CYCLE is the ratio of the time that a repetitive digital waveform is high to the total time of one period. The
specification here refers to the SCLK.
EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE BITS) is another method of specifying Signal-to-Noise
and Distortion or SINAD. ENOB is defined as (SINAD - 1.76) / 6.02 and says that the converter is
equivalent to a perfect ADC of this (ENOB) number of bits.
FULL POWER BANDWIDTH is a measure of the frequency at which the reconstructed output fundamental
drops 3 dB below its low frequency value for a full scale input.
FULL SCALE ERROR (FSE) is a measure of how far the last code transition is from the ideal 1½ LSB below
VREF+ and is defined as:
VFSE = Vmax + 1.5 LSB – VREF+
• where Vmax is the voltage at which the transition to the maximum code occurs. FSE can be expressed
in Volts, LSB or percent of full scale range.
(7)
GAIN ERROR is the deviation of the last code transition (111...110) to (111...111) from the ideal (VREF - 1.5 LSB),
after adjusting for offset error.
INTEGRAL NON-LINEARITY (INL) is a measure of the deviation of each individual code from a line drawn from
negative full scale (½ LSB below the first code transition) through positive full scale (½ LSB above
the last code transition). The deviation of any given code from this straight line is measured from
the center of that code value.
INTERMODULATION DISTORTION (IMD) is the creation of additional spectral components as a result of two
sinusoidal frequencies being applied to an individual ADC input at the same time. It is defined as
the ratio of the power in both the second or the third order intermodulation products to the power in
one of the original frequencies. Second order products are fa ± fb, where fa and fb are the two sine
wave input frequencies. Third order products are (2fa ± fb ) and (fa ± 2fb). IMD is usually expressed
in dB.
MISSING CODES are those output codes that never appear sat the ADC outputs. These codes cannot be
reached with any input value. The ADC128S052 is ensured not to have any missing codes.
OFFSET ERROR is the deviation of the first code transition (000...000) to (000...001) from the ideal (that is, GND
+ 0.5 LSB).
SIGNAL-TO-NOISE RATIO (SNR) is the ratio, expressed in dB, of the rms value of the input signal to the rms
value of the sum of all other spectral components below one-half the sampling frequency, not
including d.c. or the harmonics included in THD.
24
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: ADC128S052 ADC128S052-Q1
ADC128S052, ADC128S052-Q1
www.ti.com
SNAS333E – AUGUST 2005 – REVISED DECEMBER 2015
Device Support (continued)
SIGNAL-TO-NOISE PLUS DISTORTION (S/N+D or SINAD) Is the ratio, expressed in dB, of the rms value of the
input signal to the rms value of all of the other spectral components below half the clock frequency,
including harmonics but excluding d.c.
SPURIOUS FREE DYNAMIC RANGE (SFDR) is the difference, expressed in dB, between the desired signal
amplitude to the amplitude of the peak spurious spectral component, where a spurious spectral
component is any signal present in the output spectrum that is not present at the input and may or
may not be a harmonic.
TOTAL HARMONIC DISTORTION (THD) is the ratio, expressed in dBc, of the rms total of the first five harmonic
components at the output to the rms level of the input signal frequency as seen at the output. THD
is calculated as
THD = 20 ‡ log 10
•
A f22 +
+ A f10 2
A f12
where Af1 is the RMS power of the input frequency at the output and Af2 through Af6 are the RMS
power in the first 5 harmonic frequencies.
(8)
THROUGHPUT TIME is the minimum time required between the start of two successive conversions. It is the
acquisition time plus the conversion and read out times. In the case of the ADC128S052, this is 16
SCLK periods.
11.2 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 4. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
ADC128S052
Click here
Click here
Click here
Click here
Click here
ADC128S052-Q1
Click here
Click here
Click here
Click here
Click here
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: ADC128S052 ADC128S052-Q1
Submit Documentation Feedback
25
ADC128S052, ADC128S052-Q1
SNAS333E – AUGUST 2005 – REVISED DECEMBER 2015
www.ti.com
11.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.4 Trademarks
E2E is a trademark of Texas Instruments.
SPI, QSPI are trademarks of Motorola.
All other trademarks are the property of their respective owners.
11.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
26
Submit Documentation Feedback
Copyright © 2005–2015, Texas Instruments Incorporated
Product Folder Links: ADC128S052 ADC128S052-Q1
PACKAGE OPTION ADDENDUM
www.ti.com
22-Sep-2015
PACKAGING INFORMATION
Orderable Device
Status
(1)
ADC128S052CIMT/NOPB
Package Type Package Pins Package
Drawing
Qty
ACTIVE
TSSOP
PW
16
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
92
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
Device Marking
(4/5)
128S052
CIMT
ADC128S052CIMTX
NRND
TSSOP
PW
16
TBD
Call TI
Call TI
-40 to 125
ADC128S052CIMTX/NOPB
ACTIVE
TSSOP
PW
16
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
128S052
CIMT
ADC128S052QCMT/NOPB
ACTIVE
TSSOP
PW
16
92
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
128S052
QCMT
ADC128S052QCMTX/NOPB
ACTIVE
TSSOP
PW
16
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
128S052
QCMT
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
22-Sep-2015
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF ADC128S052, ADC128S052-Q1 :
• Catalog: ADC128S052
• Automotive: ADC128S052-Q1
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
6-Nov-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
ADC128S052CIMTX/NOP
B
TSSOP
PW
16
2500
330.0
12.4
6.95
5.6
1.6
8.0
12.0
Q1
ADC128S052QCMTX/NO
PB
TSSOP
PW
16
2500
330.0
12.4
6.95
5.6
1.6
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
6-Nov-2015
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
ADC128S052CIMTX/NOP
B
TSSOP
PW
16
2500
367.0
367.0
35.0
ADC128S052QCMTX/NOP
B
TSSOP
PW
16
2500
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated