MASK12~MASK110 Surface Mount Schottky Rectifiers Features ● Low profile package ● Ideal for automated placement ● Ultrafast reverse recovery time ● Low power losses, high efficiency ● Low forward voltage drop ● High surge capability ● High temperature soldering： ● Component in accordance to 260℃/10 seconds at terminals RoHS 2002/95/1 and WEEE 2002/96/EC Mechanical Date ● ● Major Ratings and Characteristics Case: JEDEC MSMA molded plastic IF(AV) 1.0 A body over glass passivated chip VRRM 20 V to 100 V Terminals: Solder plated, solderable per IFSM 30 A VF 0.50V,0.55V,0.70V,0.85V Tj max. 125 °C J-STD-002B and JESD22-B102D ● y Laser band denotes cathode end Polarity: Maximum Ratings & Thermal Characteristics (TA = 25 °C unless otherwise noted) Items Symbol MASK MASK MASK MASK MASK MASK MASK 16 18 12 13 14 15 110 UNIT Maximum repetitive peak reverse voltage VRRM 20 30 40 50 60 80 100 V Maximum RMS voltage VRMS 14 21 28 35 42 56 70 V Maximum DC blocking voltage VDC 20 30 40 50 60 80 100 V Maximum average forward rectified current IF(AV) 1.0 A Peak forward surge current 8.3 ms single half sine-wave superimposed on rated load IFSM 30 A Voltage rate of change (rated VR) dv/dt 10000 V/µs RθJL 35 ℃/W TJ，TSTG –65 to +125 ℃ Thermal resistance from junction to lead (1) Operating junction and storage temperature range Note 1: Mounted on P.C.B. with 0.2 x 0.2” (5.0 x 5.0mm) copper pad areas. Electrical Characteristics Items Instantaneous forward voltage Reverse current (TA = 25 °C unless otherwise noted) Test conditions Symbol IF=1.0A(2) VF VR=VDC TA=25℃ TA=100℃ Note 2: Pulse test:300μs pulse width,1% duty cycle. http://www.trr-jx.com IR MASK MASK13~ MASK15~ MASK18~ 12 MASK14 MASK16 MASK110 0.50 0.55 0.70 0.5 10 0.85 UNIT V mA MASK12~MASK110 Surface Mount Schottky Rectifiers Characteristic Curves (TA=25 ℃ unless otherwise noted) http://www.trr-jx.com MASK12~MASK110 Surface Mount Schottky Rectifiers Package Outline Notice ● Product is intended for use in general electronics applications. ● Product should be worked less than the ratings; if exceeded, may cause permanent damage.or introduce latent failure ● The absolute maximum ratings are rated values and must not be exceeded during operation. The following are the general mechanisms. derating methods you design a circuit with a device. IF(AV) : We recommend that the worst case current be no greater than 80% . IFSM : This rating specifies the non-repetitive peak current. This is only applied for an abnormal operation, which the general during the lifespan of the device. TJ : Derate this rating when using a device in order to ensure high reliability. We recommend that the device be used at a TJ of below 125°C. ● TRR is registered trademark of Rising-sun Technology. Rising-sun Technology reserves the right to make changes to any product in this specification to improve reliability,functional characteristics,or design without notice. ● Rising-sun Technology does not assure any liability arising out of the applications or any product described in this specification. ● Rising-sun Technology advises customers to obtain the latest version of the device information before placing orders to verify that the required information is current. http://www.trr-jx.com