Hirose FX15S-41P-0.5SD 1mm pitch wire-to-board connectors supporting lvds signal Datasheet

1mm Pitch Wire-to-Board Connectors supporting LVDS signal
FX15 Series
Termination side: 0.5mm pitch, 1-row construction
Mating side: 1 mm pitch, staggered 2-row construction
Contacts consolidated into 1 row for equal length transmission lines
Fig.1
■Features
1. Space-saving
Self-alignment of ±1.5mm
Large guide post
1.5mm
Reduction in space is achieved by designing the
contacts in 2-row staggered 1mm pitch on the
mating side and on a single row 0.5mm pitch on
the termination side (Fig.1).
1.5mm
2. Equal length transmission lines
Contact configuration provides equal length
transmission lines, which prevents LVDS signal
loss within the connector.
3. Variations
Fig.2
Side latch -locks
Availability of shielded and non-shielded types
allows for design flexibility and cost reduction.
4. Self alignment and self-guiding
Built-in guide posts allow secure self-alignment
within ±1.5mm (Fig.2).
5. Secure and complete mating / unmating
Side latch locking provides complete and secure
mating, as well as easy unmating (Fig.3).
6. Enhanced shielding performance with
FX15S
Enlarged metal shields prevent intrusion and
emission of electromagnetic interference, which
enhances the integrity of the LVDS signal (Fig.4).
7. RoHS compliant
All materials and substances used to produce this
product comply with RoHS standards.
With metal shields
(FX15 and FX15S Series)
Without metal shields
(FX15M Series)
Fig.3
High Shielding Performance
0
Without metal
Emitting Noise Level (dBm)
Jan.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
Space saving, Equal length transmission lines
-10
With metal
-20
-30
-40
-50
0.1 0.2
0.3
0.5
1
1.5
2
Frequency (GHz)
2015.10e
3
Fig.4
1
FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal
■Product Specifications
Current rating
Voltage rating
Jan.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
Ratings
0.5A
100V AC
Operating temperature range
Storage temperature range
-55ç to +80ç (Note 1)
-10ç to +60ç (Note 2)
Item
1. Contact resistance
2. Insulation resistance
3. Withstanding voltage
4. Insertion-Extraction force
Specification
60mø max. (Note 3)
500Mø min.
No flashover or insulation breakdown.
2N min., 30N max.
Conditions
1mA
100V DC
300V AC/one minute
With corresponding connector
5. Mating cycles
Contact resistance : 80mø max.(Note 3)
50 cycles
6. Vibration resistance
7. Shock resistance
No electrical discontinuity of 1µs or more.
No electrical discontinuity of 1µs or more.
Frequency: 10 to 55 Hz, single amplitude of 0.75mm, 2 hours, 3 axis
Acceleration of 490m/s2, 11ms durations, sine half-wave waveform, 3 cycles, 3axis.
8. Humidity resistance
Contact resistance : 80mø max.
96 hours at 40ç, RH 90% to 95%
No damage, cracks, or parts dislocation.(Note 3)
9. Temperature cycle
Contact resistance : 80mø max. (Note 3)
Insulation resistance : 500Mø min.
Temperature : -55ç → +15ç to +35ç → +85ç → +15ç to +35ç
Time
: 30 → 5 → 30 → 5 (Minutes) 5 cycles
10. Salt spray
Contact resistance : 80mø max. (Note 3)
No corrosions
5% water solution for 48 hours.
Note 1 : Includes temperature rise caused by current flow.
Note 2 : The term “storage” refers to products stored for long period of time prior to mounting and use. Operating
temperature and humidity range includes non-conducting condition of installed connectors in storage, shipment or
during transportation.
Note 3 : Includes wire conductor resistance (12mm long).
■Materials / Finish
●Receptacle
Insulator
Component
Material
Polyamide
Finish
Color : Black
Remarks
UL94V-0
Contact
Phosphor bronze
Contact area : Gold plated
Termination area : Tin plated
---------------
FX15S : Nickel silver
FX15SC : Stainless steel
FX15S : --------------FX15SC : Tin plated
---------------
Phosphor bronze
Selective gold flash plated
---------------
Insulator
Material
Polyamide
Finish
Color : Black
Remarks
UL94V-0
Contact
Phosphor bronze
Contact area : Gold plated
Termination area : Tin plated
---------------
Metal shell (shielded version only)
Metal latch locks (shielded version only)
Nickel silver
Stainless steel
-----------------------------
-----------------------------
Metal shell, metal latch locks
(on micro coax version only)
Stainless steel
Nickel plated
---------------
Metal shell (shielded version only)
Metal fittings (shielded version only)
●Plug
Component
■Product Number Structure
qSeries Name
wConfiguration
●Receptacle
FX15 S - 31 S - 0.5 SH (**)
q
w
e
r
t
y
●Plug
w
e
r
u
●Crimp contact
FX15 - 3032 PCF B
q
i
o
!0
P
S
: Male contact
: Female contact
tContact pitch
: 0.5 mm
SH
yHousing configuration
SV
: Right angle
: Straight
uTermination
C
: Crimp
0.5SD : Micro-coaxial cable
GND : Separate ground plate
iApplicable conductor
2830
3032
: 28 to 30 AWG
: 30 to 32 AWG
oPackaging
!0Plating (contact area)
PCF
B
Blank
(30)
: Male contact / reel
: Gold plated
: Embossed Packaging (1,000 pcs/reel)
: Embossed Packaging (100 pcs/reel)
!1Packaging
2
15M
: With shields (or crimp contact)
: With shields – enhanced shielding
: With shields – enhanced shielding
(PCB mounting pattern : VESA standard)
: Without shields
eNumber of contacts
rConnector type
FX15 S - 31 P - C
q
!1
: FX15
Blank
15S
15SC
FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal
■FX15 Series – Functional Diagram
Crimp contact
Plugs
Receptacles
With shields-standard
Vertical, with shields
(FX15-31P-C)
(FX15-31S-0.5SV)
Crimp contact
(FX15-3032-PCFB)
(FX15M-P-C)
Right angle, with shields
–enhanced shielding
(FX15S-S-0.5SH)
B
With shields – enhanced shielding
(FX15S-P-C)
Right angle, without shields
(FX15M-S-0.5SH)
B
Jan.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
B
Without shields
Crimp contact
(FX15-2830-PCFB)
With shields – enhanced shielding
28 to 30 AWG
(FX15SW-31P-C)
With shields – enhanced shielding
PCB mouting pattern : VESA standard
(FX15SC-S-0.5SH)
28
Ground plate
(FX15S-P-GND)
Micro-coaxial cable
(FX15S-P-0.5SD)
With shields – enhanced shielding
PCB mouting pattern : VESA standard
(FX15SC-S-0.5SV)
A
3
FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal
■Plugs
●With shields (FX15-31P-C)
(27)
24.6±0.3
22.57±0.15
2.7±0.1
18.3±0.3
3.7±0.3
Jan.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
(13.45)
9.4±0.3
Polarizing mark
indicator
No.2
Part No.
HRS No.
No. of contacts
RoHS
FX15-31P-C
575-2101-2
31
Yes
Note 1 : Packaged in trays.
Note 2 : Dimensions in parenthesis ( ) are reference dimensions.
No.1
14±0.15
P=1±0.1
No.30
P=1±0.1
15±0.15
No.31
●With shields, enhanced shielding (FX15S-**P-C)
(A)
B±0.3
C±0.15
4±0.3
2.7±0.1
(13.45)
9.4±0.3
Polarizing mark
indicator
3.7±0.3
D±0.3
No.2
No.1
No.n-1
P=1±0.1
F±0.15
No.n
Part No.
HRS No.
No. of contacts
A
B
C
D
E
F
FX15S-31P-C
575-2106-6
31
27
24.6
22.6
18.3
14
15
FX15S-41P-C
575-2107-9
41
32
29.6
27.6
23.3
19
20
FX15S-51P-C
575-2103-8
51
37
34.6
32.6
28.3
24
25
Note 1 : Packaged in trays.
Note 2 : Dimensions in parenthesis ( ) are reference dimensions.
4
E±0.15
P=1±0.1
RoHS
Yes
FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal
●With shields – enhanced shielding
28 to 30 AWG (FX15SW-31P-C)
(27)
24.6±0.3
22.57±0.15
Polarizing mark
indicator
4±0.3
2.7±0.1
(13.45)
9.4±0.3
B
28
Part No.
HRS No.
No. of contacts
RoHS
FX15SW-31P-C
575-2113-1
31
Yes
No.2
14±0.15
P=1±0.1
3.7±0.3
No.30
A
Note 1 : Packaged in trays.
Note 2 : Dimensions in parenthesis ( ) are reference dimensions.
No.1
P=1±0.1
15±0.15
No.31
●Without shields (FX15M-**P-C)
(A)
B±0.3
Polarizing mark
indicator
(13.6)
(13)
9.55±0.3
Jan.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
18.3±0.3
4.2±0.3
C±0.3
(D)
No.2
No.1
E±0.15
P=1±0.1
No.n-1
P=1±0.1
F±0.15
No.n
Part No.
HRS No.
No. of contacts
A
B
C
D
E
F
FX15M-21P-C
575-2109-4
21
24.8
20.5
13.7
25.8
9
10
FX15M-31P-C
575-2108-1
31
29.8
25.5
18.7
30.8
14
15
RoHS
Yes
Note 1 : Sold in 100 piece packages. Please order in full package quantities.
Note 2 : Dimensions in parenthesis ( ) are reference dimensions.
5
FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal
BPlug crimp contacts
Part No.
HRS No.
FX15-2830PCFB
575-2002-0
FX15-3032PCFB
575-2003-3
Packaging
Quantity
Finish
RoHS
Reel
20,000 pcs/reel
Gold plated
Yes
●Applicable cable (Tin plated, annealed copper wire)
30 AWG (7/0.1mm)
32 AWG (7/0.08mm)
Ø0.5 to 0.6mm
1571
UL No.
1516, 1571 (Note)
1571
●Wire strip length: 1.1 to 1.8mm
Note : When using wires other than those noted above, please contact Hirose for asistance.
●Tools
Item
Applicator
Press unit
6
Part No.
AP105-FX15-2830
AP105-FX15-3032
CM-105C
HRS No.
901-4036-0
901-4033-1
901-0001-0
0.35±0.1
Applicable crimp contact
FX15-2830PCFB
FX15-3032PCFB
–––––––––
(7)
Jacket diameter
1517
0.72±0.1
0.9±0.15
Jan.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
FX15-3032PCFB
Applicable wire size
(Stranded wire conductor)
Ø0.56 to 0.72mm
UL No.
2±0.15
28 AWG (7/0.127mm)
30 AWG (7/0.1mm)
Jacket diameter
0.5±0.15
FX15-2830PCFB
Applicable wire size
(Stranded wire conductor)
t=0.15±0.05
FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal
Cd#&
Cd#c
●Plug – Micro-coaxial cable (FX15S-**P-0.5SD)
Cd#'
Cd#c"&
6
7¤%#(
8¤%#&*
EdaVg^o^c\bVg`
^cY^XVidg
'#,¤%#&*
&(
-#,*¤%#(
6
Part No.
HRS No.
No. of contacts
A
B
C
D
FX15S-41P-0.5SD
575-2110-3
41
31.9
29.6
27.57
20
FX15S-51P-0.5SD
575-2118-5
51
36.9
34.6
32.57
25
(#*¤%#(
RoHS
Yes
Note 1 : Packaged in trays.
Note 2 : Dimensions in parenthesis ( ) are reference dimensions.
●Ground plate for micro-coaxial cable type
6¤%#'
&#**¤%#'
7¤%#'
'#'¤%#'
&&#)*¤%#(
Part No.
HRS No.
No. of contacts
A
B
FX15S-41P-GND
575-2111-6
41
29.2
30.06
FX15S-51P-GND
575-2117-2
51
34.2
35.06
RoHS
Yes
Note 1 : Packaged in trays.
Note 2 : Dimensions in parenthesis ( ) are reference dimensions.
●Applicable cable (Micro-coaxial cable)
6¤%#'
7¤%#&*
40 AWG (7/0.03mm)
No. of contacts
41
A
23.1
B
20
51
28.1
25
E2%#*¤%#%,
>ccZgXdcYjXidg
>chjaVidg
<gdcY^c\WVg
DjiZgXdcYjXidg
?VX`Zi
(+id)%6L<B^Xgd"XdVm^VaXVWaZ
%#+¤%#&
%#%*
"%#'
0.3mm to 0.5mm
&
38 AWG (7/0.04mm)
Jacket diameter
HdaYZgXdVi
& B>C
%
'#& "%#&
Wire size
(Standed wire inner conductor)
36 AWG (7/0.05mm)
●Cable preparation
%#.B6M
Jan.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
Cd#&
Cd#c
E2%#*¤%#&
9¤%#&*
7
FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal
■Receptacles
25.7±0.3
19.82±0.2
15±0.15
P=0.5±0.1
No.2
No.1
No.31
b
(6)
5.6±0.3
4±0.3
a
No.30
(0.8)
●Vertical, with shielding (FX15-31S-0.5SV)
e
f
d
4.8±0.3
Jan.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
0.9±0.2
c
1.5±0.2
1±0.2
1±0.2
1.5±0.2
0.8±0.1
22.8±0.3
Part No.
HRS No.
No. of contacts
RoHS
31
Yes
FX15-31S-0.5SV(**) 575-2201-7 **
[Specification Number : **, (**) ]
Blank : Embossed packaging (1,000 pcs/reel)
(30) : Embossed packaging (100 pcs/reel)
BRecommended PCB mounting pattern and metal mask dimensions
22.8±0.05
0.3±0.03(Land)
0.25±0.03(Metal mask)
6.7 +0.1
0
3.2 +0.05
0
0
1.5 -0.05
P=0.5±0.03
0
2.2 -0.1
15±0.05
2-Ø1(TH)
2
0.2 +0.1
0
2-Ø1.4(LND)
0
0.9 -0.1
4.1+0.1
0
0
17.72 -0.1
21.92 +0.1
0
Note 1 : The co-planarity of the terminal leads is as follows:
• All signals and shield leads “c” and “d”: 0.1mm max.
• Shield leads “a”, “b”, “e” and “ f ”: 0.15mm max.
2 : Area indicated by the crosshatched lines must be free of conductive traces or the conductive traces must be covered
by resist film.
3 : Packaged on tape-and-reel.
4 : Dimensions in parenthesis ( ) are reference dimensions.
8
FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal
●Right angle with shields – enhanced shielding (FX15S-**S-0.5SH)
A±0.2
0.5±0.1
0.2±0.05
4
No.n
No.n-1
(4)
4
(3)
Polarizing mark
indicator
5
(2.6)
(0.2) 4.45±0.1 (1.7)
No.2
No.1
4.4±0.3
P=1±0.1
P=1±0.1
D±0.15
E±0.3
Part No.
HRS No.
No. of contacts
A
B
C
D
E
F
G
H
FX15S-31S-0.5SH(**) 575-2306-5 **
31
15
27.4
14
15
27.8
28.8
24.8
21.6
FX15S-41S-0.5SH(**) 575-2307-8 **
41
20
32.4
19
20
32.8
33.8
29.8
26.6
FX15S-51S-0.5SH(**) 575-2303-7 **
51
25
37.4
24
25
37.8
38.8
34.8
31.6
J
K
L
M
N
P
R
S
18
15
------
------
13.2
16.8
24.8
40
23
20
18.2
21.8
29.8
45
28
25
23.2
26.8
34.8
50
5.2
8.8
RoHS
Yes
BRecommended PCB mounting pattern and metal mask dimensions
F +0.05
0
0
G -0.05
0
1.45 -0.05
0.5±0.03
0
1.7 -0.05
0
J -0.05
K±0.05
0.3±0.03(Land)
0.25±0.03(Metal mask)
0
L -0.05
M +0.05
0
0
N23.2 -0.05
P26.8 +0.05
0
2.2 +0.05
0
3
13.85
4.25
3.7 +0.05
0
2
3.7 +0.05
0
4.15
3.55 +0.05
0
0
2.05 -0.05
H+0.05
0
2
Jan.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
B±0.2
C±0.15
R
3
2
S
Note 1 : The coplanarity of the terminal leads is 0.1mm max. for all signal leads and 0.15mm max. for the shield leads.
2 : Do not place any components in the area indicated. Placement of components in this area may affect mating and
latch lock operation.
3 : Area indicated by the cross-hatched lines must be free of conductive traces or the conductive traces must be covered
by resist film.
4 : The area marked
indicates vacuum pick-and-place area for board placement with automatic equipment.
5 : Vacuum pick-up area
6 : Packaged on tape-and-reel.
7 : Dimensions in parenthesis ( ) are reference dimensions.
9
FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal
●Right angle, without shielding (FX15M-**S-0.5SH)
A±0.2
0.5±0.1
0.2±0.05
No.n-1
No.n
6.15±0.3
No.2
No.1
Polarizing mark
(5.5)
indicator
Vacuum pick and place area
4.8±0.3
Jan.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
4.3±0.3
B±0.2
C±0.15
P=1±0.1
P=1±0.1
D±0.15
6.55±0.3
[Specification Number : **, (**) ]
Blank : Embossed packaging (1,000 pcs/reel)
(30) : Embossed packaging (100 pcs/reel)
Part No.
HRS No.
No. of contacts
A
B
C
D
E
F
G
FX15M-21S-0.5SH(**)
575-2309-3 **
21
10
FX15M-31S-0.5SH(**)
575-2308-0 **
31
15
22.4
9
10
17.9
10
35
27.4
14
15
22.9
15
40
RoHS
Yes
BRecommended PCB mounting pattern and metal mask dimensions
E±0.05
4
2
14
2
3.4+0.05
0
0.25±0.03(Metal mask)
0.9±0.03
0
1.9-0.05
P=0.5±0.03
0
3.7-0.05
7.4+0.05
0
(1.85)
F±0.05
0.3±0.03(Land)
2
G
Note 1 : The co-planarity of all terminal leads is 0.1mm max.
2 : Do not place any components in the area indicated. Placement of components in this area may affect mating and
latch lock operation.
3 : Packaged on tape-and-reel.
10
FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal
●Right angle with shields – enhanced shielding (FX15SC-**S-0.5SH)
A±0.3
B±0.2
C±0.2
P=0.5±0.1
0.18±0.05
No.1
No.n
4.45±0.2
P=D±0.1
0.5±0.1
E±0.2
F±0.3
G±0.15
4.4±0.3
P=1±0.1
P=1±0.1
H±0.15
[Specification Number : **, (**) ]
Blank : Embossed packaging (1,000 pcs/reel)
(30) : Embossed packaging (100 pcs/reel)
Part No.
HRS No.
No. of contacts
A
B
C
D
E
F
G
H
J
K
FX15SC-41S-0.5SH(**) 575-2310-2 **
41
32.85
26
20
4
20
32.4
19
20
29.75
45
FX15SC-51S-0.5SH(**) 575-2311-5 **
51
37.85
31
25
5
25
37.4
24
25
34.75
50
RoHS
Yes
BRecommended PCB mounting pattern and metal mask dimensions
B±0.05
No.1
No.n
2.05±0.05
12
6-1.3±0.05
E±0.05
J±0.05
2
2
1.55±0.05
3.5±0.05
P=D±0.05
5.6
2.5±0.05
2
n-0.25±0.03
5.1±0.05
P=0.5±0.03
2.5±0.05
C±0.05
1.55±0.05
Jan.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
Polarizing mark
indicator
(0.25 )
1.5±0.1
3.1±0.2
1.5±0.1
(1.1)
PCB mounting pattern : VESA standard
3
K
Note 1 : The coplanarity of the terminal leads is 0.1mm max.
2 : Do not place any components in the area indicated. Placement of components in this area may affect mating and
latch lock operation.
3 : Area indicated by the cross-hatched lines must be free of conductive traces or the conductive traces must be covered
by resist film.
4 : Packaged on tape-and-reel.
5 : Dimensions in parenthesis ( ) are reference dimensions.
11
FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal
●Vertical with shields – enhanced shielding (FX15SC-**S-0.5SV)
PCB mounting pattern : VESA standard
A±0.2
No.1
No.n
B±0.2
0.18±0.05
P=0.5±0.1
P=C±0.1
1.5±0.1
0.5±0.1
D±0.2
Jan.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
E±0.3
5.3±0.3
4.2±0.2
5.5±0.3
[Specification Number : **, (**) ]
Blank : Embossed packaging (1,000 pcs/reel)
(30) : Embossed packaging (100 pcs/reel)
No. of contacts
A
B
C
D
E
FX15SC-41S-0.5SV(**) 575-2205-8 **
Part No.
HRS No.
41
26
20
4
20
32.4
FX15SC-51S-0.5SV(**) 575-2204-5 **
51
31
25
5
25
37.4
RoHS
Yes
BRecommended PCB layout and metal mask dimensions
A±0.05
No.n
B±0.05
P=0.5±0.3
n-0.25±0.03
2.5±0.05
2
1.55±0.05
3.5±0.05
1.55±0.05
No.1
P=C±0.05
6-1.3±0.05
2.5±0.05
D±0.05
A±0.05
Note 1 : The coplanarity of the terminal leads is 0.1mm max.
2 : Area indicated by the cross-hatched lines must be free of conductive traces or the conductive traces must be covered
by resist film.
3 : Packaged on tape-and-reel.
12
FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal
BPackaging Specifications
●Vertical, with shields
●Right angle, with shields-enhanced shielding
(FX15-31S-0.5SV)
(FX15S-**S-0.5SH)
Unreeling direction
Unreeling direction
+
0
0 .1
.5
4±0.1
B±0.1
C±0.3
A±0.1
A
A
(4.7)
(0.5)
Ø1
1.75±0.1
+
0
0 .1
5
12±0.1
20.25±0.1
40.45±0.1
44±0.3
Part No.
A
A
A
HRS No.
No. of contacts D
FX15-31S-0.5SV(**) 575-2201-7 **
31
Part No.
44.5
●Right angle, without shields
HRS No.
No. of contacts A
FX15S-31S-0.5SH(**) 575-2306-5 **
31
FX15S-41S-0.5SH(**) 575-2307-8 **
41
FX15S-51S-0.5SH(**) 575-2303-7 **
51
B
C
D
20.3 40.5 44 44.5
26.3 52.5 56 56.5
●Reel dimensions
(FX15M-**S-0.5SH)
(D)
3±
0.5
(1.6)
Ø1
Unreeling direction
(6.5)
Part No.
HRS No.
No. of contacts A
FX15M-21S-0.5SH(**) 575-2309-3 **
21
FX15M-31S-0.5SH(**) 575-2308-0 **
31
B
C
(Ø80)
A±0.1
B±0.1
C±0.3
(Ø380)
0
0 .1
(5.15)
(0.5)
.5 +
12±0.1
2±0.1 4±0.1
Ø1
Jan.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
Ø1
.
5
12±0.1
2±0.15 4±0.1
Ø1
.
+
0
0 .1
(6.7)
(6.3)
(4.8)
(0.5)
D
20.2 40.4 44 44.5
13
FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal
●Right angle with shields – enhanced shielding ●Vertical with shields – enhanced shielding
(FX15SC-**S-0.5SH)
(FX15SC-**S-0.5SV)
Unreeling direction
+
0
0 .1
B±0.1
C±0.3
B±0.1
C±0.3
A±0.1
Jan.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
Part No.
HRS No.
No. of
A
contacts
FX15SC-41S-0.5SH(**) 575-2310-2 **
41
FX15SC-51S-0.5SH(**) 575-2311-5 **
51
B
C
D RoHS
Part No.
26.2 52.4 56 56.5 Yes
0.5
3±
(Ø80)
(Ø380)
No. of
A
contacts
41
FX15SC-51S-0.5SV(**) 575-2204-5 **
51
(1.6)
Ø1
HRS No.
FX15SC-41S-0.5SV(**) 575-2205-8 **
●Reel dimensions
14
(7)
(0.5)
.5
4±0.1
A±0.1
12±0.1
2±0.1
Ø1
(6.7)
(0.5)
5
4±0.1
Ø1
.
12±0.1
2±0.1
+0
0 .1
Unreeling direction
(D)
B
C
D RoHS
26.2 52.4 56 56.5 Yes
FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal
BRecommended temperature profile
250
230
230ç
180ç
Te mp e r a t u r e ( ç )
Jan.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
180
150
HRS test conditions
Test board Glass epoxy 40mm∞30mm∞1mm thick
Solder method
: Reflow
Solder composition
: Paste
96.5%Sn/3%Ag/0.5%Cu
Metal mask
: 0.12mm thick
Reflow cycles
: 2 cycles
MAX 250ç
150ç
100
25
0
90±30sec.
30±10sec.
Preheating(150 to 180ç)
Sodering
(230çmin)
The temperature profile is based on the above
conditions.
In individual applications the actual temperature
may vary, depending on solder paste type, volume/
Time (sec.)
thickness and board size/thickness. Consult your
solder paste and equipment manufacturer for
specific recommendations.
Note : The temperature profile indicates the maximum temperature
of the connector surfaces at the highest point from the PCB
mounting surface.
BWashing Conditions
Organic Solvent Washing
Solvent type
IPA (Isoporopyl alcohol)
Room temperature washing
Yes
Heated washing
Yes
Water Type Washing
When using water type cleaning agents (e.g., terpene, and alkali saponifiers), select the cleaning agent based on the
documentation issued by the various manufacturers of cleaning agents which describes the effects on metals and resins.
Be careful that parts are not left with moisture remaining on them.
Washing Precautions
Residual flux or cleaning agent on the contacts when washing with organic solvents or water type cleaners can give rise to
the deterioration of electrical performance. In this regard it is important to check whether a thorough washing has been
performed.
15
FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal
Precautions and recommendations
◆Wire termination
The following documents will be needed in order to perform the cable terminations.
1Basic cable termination and crimp requirements (general explanations).
2Contact crimp termination machine instruction manual (Explanation of the press)
3Applicator parts installation table (Applicator installation explanation)
4Crimp conditions table (Crimp height/Tensile strength standard values)
5Crimp quality fundamentals manual (Bell-mouth dimensions, bent up, bent down, rolling, etc.)
* Correct cable preparation and crimp termination is based on understanding and following the procedures in the above documents.
Jan.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
◆Insertion of the crimp contacts in the housing
Crimp contacts are inserted in the housing as illustrated below.
Exercising caution when inserting, align the retention tab of the contact with the corresponding molded-in lance in the
housing’s contact cavity and push the contacts in.
Make sure that the contact is fully inserted and the retention tab clears the molded-in lance.
Molded-in lance
Molded-in lance
Retention tab facing up
Molded-in lance
Retention tab facing down
Retention tab
Crimp side
◆Verify that the retention tabs clear the molded-in lances as shown on the illustration below.
Retention tab
Light pull on the wire, with force NOT EXCEEDING 3N will also verify the correct contact insertion.
◆Removal of the contacts
Using sharp-pointed tool of appropriate size gently lift the molded-in tab and pull-out the terminated contacts.
Excersize caution as NOT to damage the molded-in lance.
Should the damage occur, the entire housing will need to be replaced.
1
2
16
FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal
Precautions and recommendations
[ Soldering precautions related to FX15S-**P-C connectors ]
◆Grounding Methods of the ground wire or shields for the cable assemblies
1Solder the ground wire or the shields ONLY in the areas specifically designated for this purpose, as shown on the
illustrations below.
2Observe the soldering iron tip temperature and soldering time specified.
3Do not apply excessive force to the connector by pressing it with the tip of a soldering iron.
4Do not splatter the flux from the solder core.
Jan.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
Soldering area 2
Soldering area 1
B
B
(Ground harness examples)
17
FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal
Precautions and recommendations
◆Plug – micro-coaxial cable
Cautions for soldering
1. For the micro coaxial cable assembled to this connector, cable alignment process as shown in "Recommended cable" on
the page 1 is required before assembly.
1Width of ground bar shall be 1.05mm Max. including misalignment of overlapping, flush by cutting, side drop or soldering.
Using an inadequate cable will interfere the assembly to the connector. Forceful assembly and soldering could cause
mis-soldering and damage the product.
4Pre-solder and coat the inner conductor at the cable end.
e
w
Grounding bar
q
3Length of cutting the extra cable should be 2.1mm Max.
Any longer cable may cause contact with the connector
during assembly and could damage the product.
Recommended minimum length is 2.0mm, but this can be
altered as long as good soldering ability is maintained.
Inner conductor
rSolder coating
w
Jan.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
2Minimize the length of outer conductor beyond the ground the
bar.
Outer conductor
2. Recommended solder for the assembly is flux cored solder with
0.2mm dia. (Lead-free: Sn-3Ag-0.5Cu), 21mm length.
If additional flux is used, make sure to prevent wicking onto the
contact area.
Wicking onto the contact area will cause the contacts to fail.
3. Before soldering the cable and connector with a cable assembly
machine, check the points to avoid below.
1Misalinment of cable end to the terminals in pitch direction
2Excessive floating of cable end
4. Follow the recommended temperature profile shown below for
the soldering.
qMisalignment in pitch direction
wfloating
The optimum conditions for soldering can vary depending on cable type and length, and solder type. Be sure to check the
recommended temperate profile and adjust the conditions accordingly.
Heating
265ç
Solder tip
pressurization
13~17N
250ç
Pre-heating
220ç
Heating
Temperature
265±5ç
Duration
3~4 sec
Idling 50ç
2s
1s
2s
3-4s
Duration of pressure application
18
FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal
Precautions and recommendations
5. After soldering, check that no defect is found at soldered area.
Examples of correct soldered and defective soldered state are shown below.
Solder shortage
A
solder bridge
A
B
BB
B
Floating
Correct soldering
[ Coutions for potting process ]
1. Protect the soldered area by UV cured resin (referred as "potting" hereafter), in order to prevent cable breakage during
cabling and other issues.
2. Apply 3033 manufactured by THREEBOND CO., LTD. or any equivalent product for potting.
Follow the instruction of the potting manufacturer for UV curing exposure.
3. Refer to the following conditions the potting area.
Number of contacts
A
41
23.7
51
28.7
0
1.25 -0.75
A -30
A
0
2.15 -0.4
Jan.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
AA
Enlarged view
4. Use extreme care in handling the soldered and potted assembly. Too much stress applied to the cable could break it.
19
FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal
Precautions and recommendations
[ Coutions for ground plate assembly ]
1. Attach a ground plate separately provided as FX15S-41P-GND after the cable assembly process.
2. Place the ground plate onto the connector horizontally and pinch the two components from top and bottom with your fingers.
Jan.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
Pinch from top and bottom with fingers
Ground plate
(FX15S-41P-GND)
A
A
wHorizontally
from the top
qAssembly
ePinch with fingers
3. Check the six fitting points after assembly and make sure that they are all correctly fitted together.
How to check fitting points
(Cut section of fitting points)
Fitting
Fitting
A
Fitting
Fitting
Fitting
Ground plate hooks the
protrusion of connector housing
Ground plate does not hook the
protrusion of connector housing
Fitting
OK
NG
[ Soldering to ground plate ]
1. Solder down the metal bar of the cable and ground plate after the assembly of the ground plate to enhance grounding
capability and to protect against vertical cable puling forces.
Soldering
Soldering
A
20
FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal
Precautions and recommendations
◆Packaging of the complete cable assemblies
Exercise caution as not to tangle, twist or deform the complete cable assemblies when packaging. Special care should be
taken NOT to apply any excessive stress to the individual wires.
When removing the cable assemblies from the packaging do not pull on the wires. Make sure that the latch-locks are not
interfering with packaging.
Jan.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
Packaging
Connectors
◆Mating of the connectors
These connectors have a built in polarizing feature and will NOT mate when reversed. Do NOT try and force tem together.
Align the connectors as shown on the illustration below and fully insert the plug into the receptacle. Confirm that both latchlocks are fully engaged.
Triangle mark
Triangle mark
Arrow mark
Mating
Center mark
Mating
Center mark
Additionally, this connector is equipped with reverse-insertion preventing mechanism, but a forced mating with a minimum
force of 25N could damage the connector.
Avoid any inappropriate mating, and perform the mating operation after checking the above-mentioned polarity indication.
◆Treatment after mating has been completed
After mating, please take care to prevent any stress or load on the connector during the routing of cables.
If a load of a minimum of 5N is applied on the cable, the cable (crimp contact) could come off. Further, if the entire cable is
pulled with a minimum force of 20N, the connector could be broken.
Please take extra care not to pull the cable and cause cable disconnection.
If you use a small gauge coaxial plug, a repeated rotation could also cause cable disconnection. Do not use the cable by
rotating it repeatedly. The rotation times should be limited to a maximum of 10 even if rotation is required for routing.
If your use requires folding back of the cable over the base of the connector, make sure to maintain a large turn-back
radius away from the connector base.
Take a large radius
Keep the turn-back position away
from the root of the connector.
Pulling in the horizontal direction:
Not acceptable
Pulling in the vertical direction:
Not acceptable
Rotation in the vertical direction:
Up to a maximum of 10 times
When you use the cable
by turning it back
21
FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal
Precautions and recommendations
◆Handling of Connectors after Mating
Do not to apply excessive force to the connectors when routing the cable after mating.
Pulling on the entire cable with a force of 20N or greater can damage the connector. Please take care not to pull the cable.
Jan.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
◆Un-mating of the connectors
Equally depress both sides of the latch-locks as shown on the illustration and pull the plug straight out. Do not pull on the
cables!
B
B
1
Press
1
Press
1
Press
1
Press
2Pull straight back.
B
Lock latches
B
B
22
FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal
BTechnical Information (FX15S Series)
●Eye Pattern Waveforms (700MHz)
1.5 m Cable Length
●Shielding Effectiveness (Shielding Characteristics Comparison Using a 2-chamber Shielded Room)
Measured shielding effectiveness for frequencies from 100MHz to 2GHz.
Shielded connectors show noise suppression of 10db to 20dB, when compared with connectors without the shields.
60
With cable-side shields + With PCB-side shields
50
With cable-side shields + Without PCB-side shields
40
Shielding Effect (dB)
Jan.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
1 m Cable Length
Without cable-side shields + With PCB-side shields
30
Without cable-side shields + Without PCB-side shields
¤ (0 dB line)
20
10
0
-10
0.1
0.15
0.2
0.3
0.4
0.5
0.6 0.7 0.8 0.9 1
1.5
2
Frequency (GHz)
Notes :The measurement value of “Without plug-side shields + Without receptacle-side shields” are taken as the zero level of
the graph vertical axis dB.
The respective results express the noise suppression effect (dB) as a relative comparison value to the “without shields”
condition as the reference.
23
Jan.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal
Powered by TCPDF (www.tcpdf.org)
USA:
HIROSE ELECTRIC (U.S.A.), INC. HEADQUARTERS
2688 Westhills Court, Simi Valley, CA 93065-6235
Phone : +1-805-522-7958
Fax : +1-805-522-3217
http://www.hirose.com/us/
USA:
HIROSE ELECTRIC (U.S.A.), INC. SAN JOSE OFFICE
3255 Scott Boulevard, Building 7, Suite 101
Santa Clara, CA 95054
Phone : +1-408-253-9640
Fax : +1-408-253-9641
http://www.hirose.com/us/
USA:
HIROSE ELECTRIC (U.S.A.), INC. CHICAGO OFFICE
580 Waters Edge Lane, Suite 205 Lombard IL
60148
Phone : +1-630-282-6701
Mail : [email protected]
http://www.hirose.com/us/
USA:
HIROSE ELECTRIC (U.S.A.), INC. DETROIT OFFICE (AUTOMOTIVE)
17197 N. Laurel Park Drive, Suite 253, Livonia,
MI 48152
Phone : +1-734-542-9963
Fax : +1-734-542-9964
http://www.hirose.com/us/
THE NETHERLANDS:
HIROSE ELECTRIC EUROPE B.V.
Hogehillweg #8 1101 CC Amsterdam Z-O
Phone : +31-20-6557460
Fax : +31-20-6557469
http://www.hirose.com/eu/
GERMANY:
HIROSE ELECTRIC EUROPE B.V. GERMAN BRANCH
Herzog-Carl-Strasse 4 D-73760 Ostfildern
(Scharnhauser Park)
Phone : +49-711-4560-02-1
Fax : +49-711-4560-02-299
http://www.hirose.com/eu/
GERMANY:
HIROSE ELECTRIC EUROPE B.V. NUERNBERG OFFICE
Muggenhofer Str. 136 90429 Nuernberg
Phone : +49-911 32 68 89 63
Fax : +49-911 32 68 89 69
http://www.hirose.com/eu/
GERMANY:
HIROSE ELECTRIC EUROPE B.V. HANOVER OFFICE
Bayernstr. 3, Haus C 30855 Langenhagen, Germany
Phone : +49-511 97 82 61 30
Fax : +49-511 97 82 61 35
http://www.hirose.com/eu/
FRANCE:
HIROSE ELECTRIC EUROPE B.V. PARIS OFFICE
Regus La Garenne Colombes,Place de La Belgique,
71 Boulevard National La Garenne Colombes, 92250, France
Phone : +33 (0) 1 7082 3170
Fax : +33 (1) 7082 3101
http://www.hirose.com/eu/
UNITED KINGDOM:
HIROSE ELECTRIC EUROPE BV (UK BRANCH)
4 Newton Court, Kelvin Drive, Knowlhill,
Milton Keynes, MK5 8NH
Phone : +44-1908 202050
Fax : +44-1908 202058
http://www.hirose.com/eu/
CHINA:
HIROSE ELECTRIC (SHANGHAI) CO., LTD.
1601, Henderson Metropolitan, NO.300, East Nanjing
Road, Huangpu District, Shanghai, China 200001
Phone : +86-21-6391-3355
Fax : +86-21-6391-3335
http://www.hirose.com/cn/
CHINA:
HIROSE ELECTRIC (SHANGHAI) CO.,LTD. BEIJING BRANCH
A1001, Ocean International Center, Building 56# East 4th
Ring Middle Road, ChaoYang District, Beijing, 100025
Phone : +86-10-5165-9332
Fax : +86-10-5908-1381
http://www.hirose.com/cn/
CHINA:
HIROSE ELECTRIC TECHNOLOGIES (SHENZHEN) CO., LTD.
Room 09-13, 19/F, Office Tower Shun Hing Square, Di Wang Commercial Centre,
5002 Shen Nan Dong Road, Shenzhen City, Guangdong Province, 518008
Phone : +86-755-8207-0851
Fax : +86-755-8207-0873
http://www.hirose.com/cn/
HONG KONG:
HIROSE ELECTRIC HONGKONG TRADING CO., LTD.
Room 1001, West Wing, Tsim Sha Tsui Centre, 66
Mody Road, Tsim Sha Tsui East, Kowloon, Hong Kong
Phone : +852-2803-5338
Fax : +852-2591-6560
http://www.hirose.com/hk/
TAIWAN:
HIROSE ELECTRIC TAIWAN CO., LTD.
103 8F, No.87, Zhengzhou Rd., Taipei
Phone : +886-2-2555-7377
Fax : +886-2-2555-7350
http://www.hirose.com/tw/
KOREA:
HIROSE KOREA CO., LTD.
250, Huimanggongwon-ro, Siheung-si,
Gyeonggi-do, Korea, 429-849
Phone : +82-31-496-7000,7124
Fax : +82-31-496-7100
http://www.hirose.co.kr/
SINGAPORE:
INDIA:
HIROSE ELECTRIC SINGAPORE PTE. LTD. DELHI LIAISON OFFICE
HIROSE ELECTRIC SINGAPORE PTE. LTD.
10 Anson Road #26-16, International Plaza Office NO.519, Regus-Green Boulevard, Level5, Tower C,
Sec62, Plot B-9A, Block B, Noida, 201301, Uttar Pradesh, India
079903, Singapore
Phone : +91-12-660-8018
Phone : +65-6324-6113
Fax : +91-120-4804949
Fax : +65-6324-6123
http://www.hirose.com/sg/
http://www.hirose.com/sg/
INDIA:
HIROSE ELECTRIC SINGAPORE PTE. LTD. BANGALORE LIAISON OFFICE
Unit No-403, 4th Floor, No-84, Barton Centre, Mahatma
Gandhi (MG) Road, Bangalore 560 001, Karnataka, India
Phone : +91-80-4120 1907
Fax : +91-80-4120 9908
http://www.hirose.com/sg/
MALAYSIA:
HIROSE ELECTRIC SINGAPORE PTE. LTD.
1-10-07, Suntech @ Penang Cybercity (1164),Lintang
Mayang Pasir 3,11950, Bayan Baru, Penang, Malaysia.
Phone : +604-619-2564
Fax : +604-619-2574
http://www.hirose.com/sg/
®
24
THAILAND:
HIROSE ELECTRIC SINGAPORE PTE. LTD.
BANGKOK OFFICE (REPRESENTATIVE OFFICE)
Unit 4703, 47th FL., 1 Empire Tower, South Sathorn
Road, Yannawa, Sathorn, Bangkok 10120 Thailand
Phone : +66-2-686-1255
Fax : +66-2-686-3433
http://www.hirose.com/sg/
2-6-3,Nakagawa Chuoh,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN
TEL: +81-45-620-3526 Fax: +81-45-591-3726
http://www.hirose.com
http://www.hirose-connectors.com
The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use.
The contents of this catalog are current as of date of 10/2015. Contents are subject to change without notice for the purpose of improvements.
Similar pages