DATASHEET ISL9113 Low Input Voltage and High Efficiency Synchronous Boost Converter with 1.3A Switch The ISL9113 provides a power supply solution for devices powered by three-cell alkaline, NiCd, NiMH or one-cell Li-Ion/Li-Polymer batteries. It offers either a fixed 5V or an adjustable output option for USB-OTG or portable HDMI applications. The device is guaranteed to supply 500mA from a 3V input and 5V output and has a typical 1.3A peak current limit. High 1.8MHz switching frequency allows for the use of tiny, low-profile inductors and ceramic capacitors to minimize the size of the overall solution. The ISL9113 is an internally compensated, fully integrated synchronous converter optimized for efficiency with minimal external components. At light load, the device enters skip mode and consumes only 20µA of quiescent current, resulting in higher efficiency at light loads and maximum battery life. The device is available in an 8 Ld DFN package and a 6 bump WLCSP. Related Literature • AN1816, “ISL9113ERAZ-EVZ, ISL9113ER7Z-EVZ Evaluation Board User Guide” FN8313 Rev 3.00 February 23, 2015 Features • Up to 95% efficiency at typical operating conditions • Input voltage range: 0.8V to 4.7V • Output current: Up to 500mA (VBAT = 3.0V, VOUT = 5.0V) • Low quiescent current: 20μA (typical) • Logic control shutdown (IQ < 1µA) • Fixed 5V, 5.1V or adjustable output • 1.2V EN high logic • Output disconnect during shutdown • Skip mode under light load condition • Undervoltage lockout • Fault protection: OVP (ADJ version only), OTP, short circuit • 8 Ld 2mmx2mm DFN package and 6 bump 0.8mmx1.36mm WLCSP Applications • Products including portable HDMI and USB-OTG • Smartphones • Tablet and mobile internet devices 100 VBAT = 4.2V VBAT = 3.6V 95 2.2µH 90 VBAT = 3.0V SW VBAT = 0.8V TO 4.7V 7 4.7µF 5 VBAT VOUT NC 1k 4 3 4.7µF EN PGND VFAULT 2 VOUT = 5V/500mA FAULT AGND 1 EFFICIENCY (%) 85 8 80 75 VBAT = 2.3V 70 VBAT = 1.2V 65 60 6 55 50 0.0001 FIGURE 1. TYPICAL APPLICATION (ISL9113ER7Z) FN8313 Rev 3.00 February 23, 2015 VOUT = 5.0V 0.001 0.01 LOAD CURRENT (A) 0.1 FIGURE 2. FIXED 5V EFFICIENCY (ISL9113ER7Z) Page 1 of 15 1 ISL9113 Block Diagrams ISL9113ER7Z C1 VOUT VBAT 7 UVLO VINT C2 2 VOLTAGE SELECTOR START-UP N-WELL SWITCH GATE DRIVER VOUT OVP SW L1 8 AND ANTI-CROSS CONDUCTION ZCD SW VOUT 4 CURRENT SENSE FAULT CONTROL LOGIC AND EN OFF 5 DIGITAL SOFT-START VOUT CURRENT LIMIT SLOPE COMP FAULT MONITORING gm ON 1.8MHz OSCILLATOR REFERENCE GENERATOR THERMAL SHUTDOWN 1 FN8313 Rev 3.00 February 23, 2015 VINT VOLTAGE CLAMP 6 Page 2 of 15 ISL9113 Block Diagrams (Continued) ISL9113ERAZ C1 VOUT VBAT C2 7 UVLO VINT 2 VOLTAGE SELECTOR START-UP N-WELL SWITCH GATE DRIVER VOUT OVP SW L1 8 AND ANTI-CROSS CONDUCTION ZCD EN VOUT 5 OFF SW ON CURRENT SENSE CONTROL LOGIC R1 AND DIGITAL SOFT-START CURRENT LIMIT SLOPE COMP FB FAULT MONITORING 4 gm R2 1.8MHz OSCILLATOR REFERENCE GENERATOR THERMAL SHUTDOWN 1 FN8313 Rev 3.00 February 23, 2015 VINT VOLTAGE CLAMP 6 Page 3 of 15 ISL9113 Pin Configurations ADJUSTABLE OUTPUT (8 LD DFN) TOP VIEW FIXED OUTPUT (8 LD DFN) TOP VIEW PGND 1 8 SW PGND 1 8 SW VOUT 2 7 VBAT VOUT 2 7 VBAT NC 3 6 AGND NC 3 6 AGND FAULT 4 5 EN FB 4 5 EN ADJUSTABLE OUTPUT (6 BUMP WLCSP) TOP VIEW FIXED OUTPUT (6 BUMP WLCSP) TOP VIEW SW A1 A2 PGND SW A1 A2 PGND VBAT B1 B2 VOUT VBAT B1 B2 VOUT EN C1 C2 FAULT EN C1 C2 FB Pin Descriptions 8 LD DFN PIN NUMBERS 6 BUMP WLCSP PIN NUMBERS SYMBOL PIN DESCRIPTIONS FIXED OUTPUT ADJUSTABLE OUTPUT FIXED OUTPUT ADJUSTABLE OUTPUT 1 1 A2 A2 PGND Power ground 2 2 B2 B2 VOUT Device output 3 3 - - NC No connection 4 - C2 - FAULT Fault output; outputs logic LOW under a number of fault conditions (see Table 1 on page 9). - 4 - C2 FB Feedback pin of the converter. Connect voltage divider resistors between VOUT, FB and GND for desired output. 5 5 C1 C1 EN The EN pin is an active-HIGH logic input for enabling the device. When asserted HIGH, the boost function begins. When asserted LOW, the device is completely disabled, and current is blocked from flowing from the SW pin to the output and vice versa. This pin should be tied either HIGH to enable the device, or LOW to disable the device. 6 6 - - AGND 7 7 B1 B1 VBAT Device input supply from a battery. Connect a 4.7µF ceramic capacitor to the power ground. 8 8 A1 A1 SW The SW pin is the switching node of the power converter. Connect one terminal of the inductor to the SW pin and the other to power input. - - EPAD FN8313 Rev 3.00 February 23, 2015 Analog ground The exposed pad (available only in the 8 Ld DFN package) must be connected to PGND pin for proper electrical performance. Place as many vias as possible under the pad connecting to the system GND plane for optimal thermal performance. Page 4 of 15 ISL9113 Ordering Information PART NUMBER (Notes 1, 4) PART MARKING VOUT (V) TEMP RANGE (°C) PACKAGE (RoHS Compliant) PKG. DWG. # ISL9113ER7Z-T (Note 2) 137 5.0 -20 to +85 8 Ld DFN L8.2x2D ISL9113ERAZ-T (Note 2) 13A Adjustable -20 to +85 8 Ld DFN L8.2x2D ISL9113EI9Z-T (Note 3) 139 5.1 -20 to +85 6 Bump WLCSP W3x2.6 ISL9113EIAZ-T (Note 3) 13A Adjustable -20 to +85 6 Bump WLCSP W3x2.6 ISL9113ER7Z-EVZ Evaluation Board for ISL9113ER7Z ISL9113ERAZ-EVZ Evaluation Board for ISL9113ERAZ ISL9113EI9Z-EVZ Evaluation Board for ISL9113EI9Z ISL9113EIAZ-EVZ Evaluation Board for ISL9113EIAZ NOTES: 1. Please refer to Tech Brief TB347 for details on reel specifications. 2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 3. These Intersil Pb-free WLCSP and BGA packaged products employ special Pb-free material sets; molding compounds/die attach materials and SnAgCu - e1 solder ball terminals, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free WLCSP and BGA packaged products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 4. For Moisture Sensitivity Level (MSL), please see device information page for ISL9113. For more information on MSL please see Tech Brief TB363. FN8313 Rev 3.00 February 23, 2015 Page 5 of 15 ISL9113 Absolute Maximum Ratings Thermal Information VBAT, EN, FAULT, VOUT, FB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 6.5V SW Voltage DC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 6.5V Pulse < 10ns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 8.0V ESD Ratings Human Body Model (Tested per JESD22-A114F) . . . . . . . . . . . . . . . . 3kV *Other ESD Spec should meet Level 1 requirement Latch-up (Tested per JESD78; Class 2, Level A) . . . . . . . . . . . . . . . . 100mA Thermal Resistance (Typical) JA (°C/W) JC (°C/W) 8 Ld DFN Package (Notes 5, 6). . . . . . . . . . 80 15 6 Bump WLCSP (Note 5) . . . . . . . . . . . . . . . 116 Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . .-20°C to +125°C Operating Temperature Range . . . . . . . . . . . . . . . . . . . . . . . -20°C to +85°C Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see TB493 Recommended Operating Conditions VBAT (After Start-up) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.8V to 4.7V VOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (VBAT + 0.2V) to 5.2V Ambient Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . -20°C to +85°C CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 5. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech Brief TB379. 6. For JC the “case temp” location is the center of the exposed metal pad on the package underside. Electrical Specifications VBAT = 3.0V, VOUT = 5.0V, TA = +25°C (see “Typical Application Circuit” on page 7). Boldface limits apply across the operating temperature range, -20°C to +85°C. PARAMETER SYMBOL TEST CONDITIONS MIN (Note 7) TYP MAX (Note 7) UNITS Start-up Voltage VMIN VEN = 1.2V, RLOAD = 50Ω 2.8 3.0 Input Undervoltage Lockout VUVLO VEN = VBAT, RLOAD = 50Ω, DFN versions only 0.68 0.70 0.76 V 800 816 mV 5.2 V V Feedback Voltage VFB ADJ version only 784 Output Voltage VOUT VBAT = 2.8V, ADJ version only 3.0 ILOAD = 50mA, 5V DFN Fixed version 4.9 5 5.1 V ILOAD = 1mA or 50mA, 5.1V WLCSP Fixed version 4.96 5.1 5.2 V 100 nA Feedback Pin Input Current VFB = 0.8V, ADJ version only Quiescent Current from VOUT IQ1 VBAT = VEN = 1.2V, No Load (Note 8) 20 45 μA Shutdown Current from VBAT ISD VEN = 0V, VBAT = 1.2V, VO = 0 0.5 2 μA 1 μA Leakage Current at SW Pin VEN = 0V, VBAT = 4.7V, VO = 0 N-Channel MOSFET ON-resistance 0.20 Ω P-Channel MOSFET ON-resistance 0.35 Ω N-Channel MOSFET Peak Current Limit IPK Maximum Duty Cycle DMAX PWM Switching Frequency FOSC EN Logic High 1.3 1.5 A 85 87.5 DFN version 1.5 1.8 2.0 MHz WLCSP version 1.7 1.8 2.2 MHz 2.5V < VBAT < 4.7V VBAT < 2.5V EN Logic Low 1.1 % 1.2 V 0.48*VBAT V 2.5V < VBAT < 4.7V VBAT < 2.5V 0.35 V 0.14*VBA V T Soft-Start-Up Time FN8313 Rev 3.00 February 23, 2015 COUT = 4.7μF, L = 2.2μH 0.2 1 ms Page 6 of 15 ISL9113 Electrical Specifications VBAT = 3.0V, VOUT = 5.0V, TA = +25°C (see “Typical Application Circuit” on page 7). Boldface limits apply across the operating temperature range, -20°C to +85°C. (Continued) PARAMETER SYMBOL TEST CONDITIONS MIN (Note 7) FAULT Pin Leakage Current when High VFAULT = VOUT FAULT Pin Sink Current when Low VFAULT = 0.5V 10 ILOAD = 0 to 100mA, DFN versions -1.5 Load Regulation ΔVOUT/VOUT VBAT = 3.0V to 3.6V, ILOAD = 1mA Output Overvoltage Protection Threshold ADJ version only Thermal Shutdown MAX (Note 7) UNITS 100 nA mA +1.5 ±1.5 ILOAD = 0 to 100mA, WLCSP versions Line Regulation TYP -1.0 TSD Thermal Shutdown Hysteresis % % +1.0 % 5.9 V 150 oC 25 oC NOTES: 7. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design. 8. IQ1 is measured at VOUT and multiplied by VOUT/VBAT; thus, the equivalent input quiescent current is calculated. the inductor current ramps down until the next clock. At this point, following a short dead time, the N-channel MOSFET is again turned ON, repeating as previously described. Typical Application Circuit 2.2µH 8 VBAT = 0.8V TO 4.7V 4.7µF SW 7 VBAT 5 EN VOUT = VOUT 2 523k FB 4 5.0V/500mA 4.7µF 100k GND 1 ISL9113ERAZ FIGURE 3. POWER SUPPLY SOLUTION FOR VOUT = 5V Detailed Description Current Mode PWM Operation The control scheme of the device is based on the peak current mode control and the control loop is compensated internally. The peak current of the N-channel MOSFET switch is sensed to limit the maximum current flowing through the switch and the inductor. The typical current limit is set to 1.3A. The control circuit includes a ramp generator, slope compensator, error amplifier and a PWM comparator (see “Block Diagrams” on pages 2 and 3). The ramp signal is derived from the inductor current. This ramp signal is then compared to the error amplifier output to generate the PWM gating signals for driving both N-channel and P-channel MOSFETs. The PWM operation is initialized by the clock from the internal oscillator (typical 1.8MHz). The N-channel MOSFET is turned ON at the beginning of a PWM cycle, the P-channel MOSFET remains OFF and the current starts ramping up. When the sum of the ramp and the slope compensator output reaches the error amplifier output voltage, the PWM comparator outputs a signal to turn OFF the N-channel MOSFET. Here, both MOSFETs remain OFF during the dead-time interval. Next, the P-channel MOSFET is turned ON and remains ON until the end of this PWM cycle. During this time, FN8313 Rev 3.00 February 23, 2015 Skip Mode Operation The boost converter is capable of operating in two different modes. When the inductor current is sensed to cross zero for eight consecutive times, the converter enters skip mode. In skip mode, each pulse cycle is still synchronized by the PWM clock. The N-channel MOSFET is turned ON at the rising edge of the clock and turned OFF when the inductor peak current reaches typically 25% of the current limit. Then, the P-channel MOSFET is turned ON, and it stays ON until its current goes to zero. Subsequently, both N-channel and P-channel MOSFETs are turned OFF until the next clock cycle starts, at which time the N-channel MOSFET is turned ON again. When VOUT is 1.5% higher than the nominal output voltage, the N-channel MOSFET is immediately turned OFF and the P-channel MOSFET is turned ON until the inductor current goes to zero. The N-channel MOSFET resumes operation when VFB falls back to its nominal value, repeating the previous operation. The converter returns to 1.8MHz PWM mode operation when VFB drops 1.5% below its nominal voltage. Given the skip mode algorithm incorporated in the ISL9113, the average value of the output voltage is approximately 0.75% higher than the nominal output voltage under PWM operation. This positive offset improves the load transient response when switching from skip mode to PWM mode operation. The ripple on the output voltage is typically 1.5%*VOUT (nominal) when input voltage is sufficiently lower than output voltage, and it increases as the input voltage approaches the output voltage. Synchronous Rectifier The ISL9113 integrates one N-channel MOSFET and one P-channel MOSFET to realize a synchronous boost converter. Because the commonly used discrete Schottky rectifier is replaced with the low rDS(ON) P-channel MOSFET, the power conversion efficiency reaches a value above 90%. Since a typical step-up converter has a conduction path from the input to the Page 7 of 15 ISL9113 output via the body diode of the P-channel MOSFET, a special circuit (see “Block Diagrams” on pages 2 and 3) is used to reverse the polarity of the P-channel body diode when the device is shut down. Thus, this configuration completely disconnects the load from the input during shutdown of the converter. The benefit of this feature is that the battery will not be completely depleted during shutdown of the converter. No additional components are needed to disconnect the battery from the output of the converter. divider should be placed close to the FB pin to prevent noise pickup. Figures 4 and 5 show the recommended PCB layout. In the 8 Ld DFN package, the heat generated in the device is mainly dissipated through the thermal pad. Maximizing the copper area connected to the thermal pad is preferable. It is recommended to add at least 4 vias within the pad to the GND plane for the best thermal relief. Soft-Start The soft start-up duration is the time between the device being enabled and VOUT rising to within 3% of target voltage. When the device is enabled, the start-up cycle starts with a linear phase. During the linear phase, the rectifying switch is turned ON in a current limited configuration, delivering about 350mA, until the output capacitor is charged to approximately 90% of the input voltage. At this point, PWM operation begins in boost mode. If the output voltage is below 2.3V, PWM switching is done at a fixed duty-cycle of 75% until the output voltage reaches 2.3V. When the output voltage exceeds 2.3V, the closed-loop current mode PWM loop overrides the duty cycle until the output voltage is regulated. Peak inductor current is ramped to the final value (typically 1.3A) during the soft-start period to limit inrush current from the input source. Fault monitoring begins approximately 2ms after the device is enabled. Over-temperature Protection (OTP) FIGURE 4. RECOMMENDED PCB LAYOUT (DFN VERSION) The device offers over-temperature protection. A temperature sensor circuit is integrated and monitors the internal IC temperature. Once the temperature exceeds the preset threshold (typically +150°C), the IC shuts down immediately. The OTP has a typical hysteresis of +25°C. When the device temperature decreases by this, the device starts operating. GND VBAT Fault Monitoring and Reporting Fault monitoring starts 2ms after start-up. Table 1 shows the response to different detected faults. Any fault condition shown in Table 1 causes the FAULT pin to be taken LOW. The FAULT pin will not release until VBAT and VOUT fully collapse or until the fault condition is removed. Printed Circuit Board Layout Recommendations The ISL9113 is a high frequency switching boost converter. Accordingly, the converter has fast voltage change and high switching current that may cause EMI and stability issues if the layout is not done properly. Therefore, careful layout is critical to minimize the trace inductance and reduce the area of the power loop. Power components, such as input capacitor, inductor and output capacitor, should be placed close to the device. Board traces that carry high switching current should be routed wide and short. A solid power ground plane is important for EMI suppression. The switching node (SW pin) of the converter and the traces connected to this pin are very noisy. Noise sensitive traces, such as the FB trace, should be kept away from SW node. The voltage FN8313 Rev 3.00 February 23, 2015 VOUT GND FIGURE 5. RECOMMENDED PCB LAYOUT (WLCSP VERSION) Fixed and Adjustable Output Voltage ISL9113 offers options for fixed output voltage of 5V, 5.1V or an adjustable output voltage. For the fixed output voltage version (ISL9113ER7Z, ISL9113EI9Z-T), an internal voltage divider is used (see “Block Diagrams”, “ISL9113ER7Z” on page 2). For the adjustable output voltage version (ISL9113ERAZ), the output voltage is programmed by connecting two external voltage divider resistors between VOUT, FB and GND (see “Block Diagrams”, “ISL9113ERAZ” on page 3). Page 8 of 15 ISL9113 TABLE 1. FAULT DETECTION AND RESPONSE FAULT CONDITION DETECTION DETAILS ACTION Low Battery Voltage VBAT < 0.7V VOUT out of Regulation VOUT is 10% below the target output voltage Shut down only if VBAT and VOUT fall below 2.1V. Device automatically restarts after 200ms. FAULT signal switches ON and OFF when VOUT drops out of regulation due to overload condition. Short Circuit VOUT falls below VBAT Shut down immediately. Device automatically restarts after 200ms. Over-temperature Protection Die temperature is > +150°C Switching stops. Device automatically restarts when temperature decreases to +125°C. Shut down until VEN or VBAT is cycled. Output Overvoltage Protection (ADJ version only) VOUT > 5.9V Switching stops until EN pin is toggled or power is cycled. Output Voltage Setting Resistor Selection For the ISL9113 adjustable output version, resistors R1 and R2, shown in the Block Diagram “ISL9113ERAZ” on page 3, set the desired output voltage values. The output voltage can be calculated using Equation 1: R 1 V OUT = V FB 1 + ------- R 2 (EQ. 1) where VFB is the internal FB reference voltage (0.8V typical). The current flowing through the divider resistors is calculated as VOUT /(R1 + R2). Large resistance is recommended to minimize current into the divider and thus improve the total efficiency of the converter. R1 and R2 should be placed close to the FB pin of the device to prevent noise pickup. Inductor Selection An inductor with core material suitable for high frequency applications (e.g., ferrite) is desirable to minimize core loss and improve efficiency. The inductor should have a low ESR to reduce copper loss. Moreover, the inductor saturation current should be higher than the maximum peak current of the device; i.e., 1.5A. The device is designed to operate with an inductor value of 2.2µH to provide stable operation across the range of load, input and output voltages. Stable mode switching between PWM and skip mode operation is guaranteed at this inductor value. Table 2 shows recommended inductors. Capacitor Selection INPUT CAPACITOR A minimum of a 4.7µF ceramic capacitor is recommended to provide stable operation under typical operating conditions. For input voltage less than 1.0V application, an additional 4.7µF ceramic capacitor is recommended for better noise filtering and EMI suppression. The input capacitor should be placed close to the input pin, GND pin and the non-switching terminal of the inductor. OUTPUT CAPACITOR For the output capacitor, a ceramic capacitor with small ESR is recommended to minimize output voltage ripple. A typical 4.7µF should be used to provide stable operation at different typical operating conditions. The output capacitor should be placed close to the output pin and GND pin of the device. Table 3 shows the recommended capacitors. TABLE 3. CAPACITOR VENDOR INFORMATION MANUFACTURER SERIES WEBSITE AVX X5R www.avx.com Murata X5R www.murata.com Taiyo Yuden X5R www.t-yuden.com TDK X5R www.tdk.com TABLE 2. INDUCTOR VENDOR INFORMATION MANUFACTURER PART NUMBER DIMENSIONS- W x L x H (mm) Murata LQH32PN2R2NN0L 3.2 x 2.5 x 1.7(max) Toko 1239AS-H-2R2M 2.5 x 2.0 x 1.2(max) 1286AS-H-2R2M 2.0 x 1.6 x 1.2(max) TDK TFM201610A-2R2M 2.0 x 1.6 x 1.0(max) Cyntec PSE25201B-2R2MS 2.0 x 1.6 x 1.2(max) FN8313 Rev 3.00 February 23, 2015 Page 9 of 15 ISL9113 Typical Characteristics 1.2 100 VBAT = 3.6V 95 VBAT = 4.2V 90 VBAT = 3.0V 1.0 0.8 80 IOUT (A) EFFICIENCY (%) 85 VOUT = 5.0V 75 VBAT = 2.3V 70 VOUT = 4.0V 0.6 0.4 65 VBAT = 1.2V 60 0.2 55 VOUT = 5.1V 50 0.0001 0.001 0.01 0.1 0 0.8 1 1.3 1.8 LOAD CURRENT (A) FIGURE 6. FIXED 5.1V EFFICIENCY (ISL9113EI9Z) 2.3 2.8 3.3 VBAT (V) 3.8 4.3 4.8 FIGURE 7. MAXIMUM OUTPUT CURRENT vs INPUT VOLTAGE (ISL9113ERAZ) L = 2.2µH, COUT = 4.7μF 5.16 VIN = 3.0V, VOUT = 5.0V, ILOAD = 20mA 5.14 VOUT (V) VOUT WITH 5V OFFSET (200mV/DIV) ILOAD = 1mA (PFM) 5.12 5.10 ILOAD = 100mA (PWM) 5.08 INDUCTOR CURRENT(500mA/DIV) 5.06 5.04 SW (5V/DIV) 5.02 0 1 2 3 4 5 VBAT (V) TIME 10µs/DIV FIGURE 9. PULSE SKIP MODE WAVEFORM FIGURE 8. LINE REGULATION, VOUT = 5V (ISL9113ER7Z) L = 2.2µH, COUT = 4.7μF VBAT = 3.0V, VOUT = 5.0V, ILOAD = 250mA VBAT = 3.0V, VOUT = 5.0V, ILOAD = 250mA EN VOUT WITH 5.0V OFFSET (50mV/DIV) VOUT (2V/DIV) INDUCTOR CURRENT(500mA/DIV) INDUCTOR CURRENT(500mA/DIV) SW(5V/DIV) SW (2V/DIV) TIME 1µs/DIV FIGURE 10. PWM WAVEFORM FN8313 Rev 3.00 February 23, 2015 TIME 40ms/DIV FIGURE 11. START-UP AFTER ENABLE (ILOAD = 250mA) Page 10 of 15 ISL9113 Typical Characteristics (Continued) VBAT = 3.6V, VOUT = 5.0V VBAT = 3.0V, VOUT = 5.0V, ILOAD = 50mA VOUT (100mV/DIV) EN (5V/DIV) VOUT (2V/DIV) INDUCTOR CURRENT(500mA/DIV) ILOAD AT 0.66Ω (200mV/DIV) INDUCTOR CURRENT(500mA/DIV) SW(5V/DIV) TIME 400µs/DIV TIME 40ms/DIV FIGURE 12. START-UP AFTER ENABLE (ILOAD = 50mA) FIGURE 13. LOAD TRANSIENT RESPONSE (100mA TO 500mA) 5.20 VBAT = 3.6V, VOUT = 5.0V 5.15 VOUT (V) VOUT (200mV/DIV) TBD 5.10 4.2V INDUCTOR CURRENT(500mA/DIV) 5.05 ILOAD AT 0.66Ω (200mV/DIV) 5.00 TIME 400µs/DIV FIGURE 14. LOAD TRANSIENT RESPONSE (20mA TO 250mA) FN8313 Rev 3.00 February 23, 2015 3.0V 0 0.2 0.4 0.6 3.6V 0.8 ILOAD (A) FIGURE 15. LOAD REGULATION (ISL9113ER7Z) Page 11 of 15 1.0 ISL9113 Revision History The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make sure you have the latest revision. DATE REVISION CHANGE February 23, 2015 FN8313.3 Updated Datasheet with Intersil new standards. On page 6, under the“Absolute Maximum Ratings” section added “FB” to the first line. Replaced Figure 9 on page 10. Updated the About Intersil verbiage. February 18, 2013 FN8313.2 Page 1: Added 5.1V or Adjustable Output options to “Features” Removed "Coming Soon" from WLCSP package references Updated Figure 2. Changed y axis scale Page 5: Added information for WLCSP package option. Page 6: Removed Machine Model from “ESD Ratings”. Added “Thermal Information” for WLCSP. “Electrical Specifications” on page 6: “Input Undervoltage Lockout”, aded "DFN versions only" to test conditions. Changed parameter name from “Output Voltage Accuracy” to “Output Voltage”. Added "5V DFN Fixed version" to test conditions where ILOAD = 50mA. Changed MIN/MAX from -100/+100 mV to 4.9/5.1 V. Added TYP. Added lines for ADJ version only and WLCSP Fixed version. Added "ADJ version only" to test conditions for “Feedback Voltage”. Added test conditions for “Feedback Pin Input Current”. Added WLCSP specs for “PWM Switching Frequency”. “Electrical Specifications” on page 7: Added "DFN versions" to test conditions for “Load Regulation” where ILOAD = 0 to 100mA. Added line for WLCSP versions. Added test conditions for “Output Overvoltage Protection Threshold”. Page 8: Added Figure 5 “RECOMMENDED PCB LAYOUT (WLCSP VERSION)”. Changed “Fixed and Adjustable Output Voltage” from: “ISL9113 offers options for fixed output voltage of 5V or an adjustable output voltage. For fixed output voltage version (ISL9113ER7Z)..” to: “ISL9113 offers options for fixed output voltage of 5V, 5.1V, or an adjustable output voltage. For fixed output voltage version (ISL9113ER7Z, ISL9113EI9Z-T)..” Revised Table 2. Added dimensions. Revised Manufacturers and Part Numbers. Added new efficiency plot, Figure 6. Added “W3x2.6” on page 15. January 16, 2013 July 12, 2012 FN8313.1 Updated Related Literature on page 1. Changed ESD Ratings in “Absolute Maximum Ratings” on page 6 as follows: HBM from 2.5kV to 3kV MM from 250V to 300V FN8313.0 Initial Release. FN8313 Rev 3.00 February 23, 2015 Page 12 of 15 ISL9113 About Intersil Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets. For the most updated datasheet, application notes, related documentation and related parts, please see the respective product information page found at www.intersil.com. You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask. Reliability reports are also available from our website at www.intersil.com/support © Copyright Intersil Americas LLC 2012-2015. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners. For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com FN8313 Rev 3.00 February 23, 2015 Page 13 of 15 ISL9113 Package Outline Drawing L8.2x2D 8 LEAD DUAL FLAT NO-LEAD PLASTIC PACKAGE (DFN) WITH EXPOSED PAD Rev 0, 3/11 2.00 6 PIN 1 INDEX AREA 6 PIN #1 INDEX AREA A B 8 1 2.00 6x 0.50 (4X) 1.55±0.10 0.15 0.10M C A B 0.22 4 TOP VIEW ( 8x0.30 ) 0.90±0.10 0±0.10 0±0.10 BOTTOM VIEW SEE DETAIL "X" C 0.10 C 0.90±0.10 BASE PLANE 0 . 00 MIN. 0 . 05 MAX. SEATING PLANE 0.08 C SIDE VIEW 0 . 2 REF C DETAIL "X" ( 8x0.20 ) PACKAGE OUTLINE ( 8x0.30 ) NOTES: 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994. 3. Unless otherwise specified, tolerance: Decimal ± 0.05 4. Dimension applies to the metallized terminal and is measured ( 6x0.50 ) 1.55 2.00 between 0.15mm and 0.30mm from the terminal tip. ( 8x0.22 ) 0.90 2.00 TYPICAL RECOMMENDED LAND PATTERN FN8313 Rev 3.00 February 23, 2015 5. Tiebar shown (if present) is a non-functional feature. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. Page 14 of 15 ISL9113 Package Outline Drawing W3x2.6 3X2 ARRAY 6 BALL WAFER LEVEL CHIP SCALE PACKAGE (WLSCP 0.4MM PITCH) Rev 3, 1/13 X 1.360±0.03 Y 0.280 0.200 0.800 2 0.800±0.03 (4X) 0.10 PIN 1 (A1 CORNER) 1 0.400 0.200 C TOP VIEW B A 6X 0.265±0.035 BOTTOM VIEW PACKAGE OUTLINE 4 0.240 SEATING PLANE 3 2 0.10 0.05 ZXY Z 0.265±0.035 Z 0.400 0.200±0.030 0.05 Z 0.290 6 0.500±0.050 NSMD TYPICAL RECOMMENDED LAND PATTERN SIDE VIEW NOTES: 1. Dimensions and tolerance per ASME Y 14.5M - 1994. 2. Dimension is measured at the maximum bump diameter parallel to primary datum Z . 3. Primary datum Z and seating plane are defined by the spherical crowns of the bump. 4. Bump position designation per JESD 95-1, SPP-010. 5. All dimensions are in millimeters. 6. NSMD refers to non-solder mask defined pad design per Intersil Tech Brief www.intersil.com/data/tb/tb451.pdf 7. Ball height and post saw device size can vary by ±10µm depending on final selection of assembly vendor. FN8313 Rev 3.00 February 23, 2015 Page 15 of 15