Infineon ICLS6023J Led system driver ic Datasheet

LED System Driver ICs
ICLS6021J
ICLS6022J
ICLS6022G
ICLS6023J
Off-Line LED Current Mode Controllers
with Integrated 650 V CoolMOS™ & Startup Cell
ICLS6x Series
Data Sheet
Version 1.0, 2011-05-19
Industrial & Multimarket
Edition 2011-05-19
Published by
Infineon Technologies AG
81726 Munich, Germany
© 2011 Infineon Technologies AG
All Rights Reserved.
Legal Disclaimer
The information given in this document shall in no event be regarded as a guarantee of conditions or
characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any
information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties
and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights
of any third party.
Information
For further information on technology, delivery terms and conditions and prices, please contact the nearest
Infineon Technologies Office (www.infineon.com).
Warnings
Due to technical requirements, components may contain dangerous substances. For information on the types in
question, please contact the nearest Infineon Technologies Office.
Infineon Technologies components may be used in life-support devices or systems only with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure
of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support
devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain
and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may
be endangered.
LED System Driver ICs
ICLS6x Series
Revision History
Page or Item
Subjects (major changes since previous revision)
Version 1.0, 2011-05-19
New ICs added: ICLS6022G and ICLS6023J
Version 1.0, 2010-08-10
First edition
Trademarks of Infineon Technologies AG
AURIX™, C166™, CanPAK™, CIPOS™, CIPURSE™, EconoPACK™, CoolMOS™, CoolSET™,
CORECONTROL™, CROSSAVE™, DAVE™, EasyPIM™, EconoBRIDGE™, EconoDUAL™, EconoPIM™,
EiceDRIVER™, eupec™, FCOS™, HITFET™, HybridPACK™, I²RF™, ISOFACE™, IsoPACK™, MIPAQ™,
ModSTACK™, my-d™, NovalithIC™, OptiMOS™, ORIGA™, PRIMARION™, PrimePACK™, PrimeSTACK™,
PRO-SIL™, PROFET™, RASIC™, ReverSave™, SatRIC™, SIEGET™, SINDRION™, SIPMOS™,
SmartLEWIS™, SOLID FLASH™, TEMPFET™, thinQ!™, TRENCHSTOP™, TriCore™.
Other Trademarks
Advance Design System™ (ADS) of Agilent Technologies, AMBA™, ARM™, MULTI-ICE™, KEIL™,
PRIMECELL™, REALVIEW™, THUMB™, µVision™ of ARM Limited, UK. AUTOSAR™ is licensed by AUTOSAR
development partnership. Bluetooth™ of Bluetooth SIG Inc. CAT-iq™ of DECT Forum. COLOSSUS™,
FirstGPS™ of Trimble Navigation Ltd. EMV™ of EMVCo, LLC (Visa Holdings Inc.). EPCOS™ of Epcos AG.
FLEXGO™ of Microsoft Corporation. FlexRay™ is licensed by FlexRay Consortium. HYPERTERMINAL™ of
Hilgraeve Incorporated. IEC™ of Commission Electrotechnique Internationale. IrDA™ of Infrared Data
Association Corporation. ISO™ of INTERNATIONAL ORGANIZATION FOR STANDARDIZATION. MATLAB™ of
MathWorks, Inc. MAXIM™ of Maxim Integrated Products, Inc. MICROTEC™, NUCLEUS™ of Mentor Graphics
Corporation. Mifare™ of NXP. MIPI™ of MIPI Alliance, Inc. MIPS™ of MIPS Technologies, Inc., USA. muRata™
of MURATA MANUFACTURING CO., MICROWAVE OFFICE™ (MWO) of Applied Wave Research Inc.,
OmniVision™ of OmniVision Technologies, Inc. Openwave™ Openwave Systems Inc. RED HAT™ Red Hat, Inc.
RFMD™ RF Micro Devices, Inc. SIRIUS™ of Sirius Satellite Radio Inc. SOLARIS™ of Sun Microsystems, Inc.
SPANSION™ of Spansion LLC Ltd. Symbian™ of Symbian Software Limited. TAIYO YUDEN™ of Taiyo Yuden
Co. TEAKLITE™ of CEVA, Inc. TEKTRONIX™ of Tektronix Inc. TOKO™ of TOKO KABUSHIKI KAISHA TA.
UNIX™ of X/Open Company Limited. VERILOG™, PALLADIUM™ of Cadence Design Systems, Inc. VLYNQ™
of Texas Instruments Incorporated. VXWORKS™, WIND RIVER™ of WIND RIVER SYSTEMS, INC. ZETEX™ of
Diodes Zetex Limited.
Last Trademarks Update 2011-02-24
Data Sheet
3
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
Table of Contents
Table of Contents
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Current Mode Controllers with Integrated 650 V Startup Cell/Depletion CoolMOS™ . . . . . . . . . 7
1
1.1
1.2
1.3
1.4
1.5
Pin Configuration and Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Pin Configuration for PG-DIP-8-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
PG-DIP-8-6 Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Pin Configuration for PG-DSO-16/12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
PG-DSO-16/12 Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Pin Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3
3.1
3.2
3.3
3.4
3.4.1
3.4.2
3.4.3
3.5
3.5.1
3.5.2
3.6
3.6.1
3.6.2
3.6.2.1
3.6.2.2
3.6.2.3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Startup Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PWM Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oscillator and Jittering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PWM Latch FF1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gate Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Current Limiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Leading Edge Blanking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Propagation Delay Compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjustable Blanking Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Protection Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto Restart Mode during Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto Restart Mode during RUN Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Floating Load Protection (FLP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
13
14
15
16
16
17
17
18
19
19
21
21
22
22
23
23
4
4.1
4.2
4.3
4.3.1
4.3.2
4.3.3
4.3.4
4.3.5
4.3.6
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supply Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Internal Voltage Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PWM Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Current Limiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CoolMOS™ Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
24
25
25
25
26
26
27
27
28
5
Temperature Derating Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6
6.1
6.2
Outline Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Outline Dimensions of PG-DIP-8-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Outline Dimensions of PG-DSO-16/12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
7
Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Data Sheet
4
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
List of Figures
List of Figures
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11
Figure 12
Figure 13
Figure 14
Figure 15
Figure 16
Figure 17
Figure 18
Figure 19
Figure 20
Figure 21
Figure 22
Figure 23
Figure 24
Data Sheet
Typical application of ICLS602xX controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Pin configuration of PG-DIP-8-6 (top view). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Pin configuration of PG-DSO-16/12 (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Block diagram of ICLS602xX controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Power management of ICLS602xX controllers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Soft start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Startup phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
PWM section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Gate driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Current limiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Leading edge blanking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Peak current overshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Overcurrent shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Dynamic voltage threshold Vcsth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Adjustable blanking window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Auto Restart mode during startup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Auto Restart mode during RUN mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Safe Operating Area (SOA) curve for ICLS6021J . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Safe Operating Area (SOA) curve for ICLS6022J and ICLS6022G . . . . . . . . . . . . . . . . . . . . . . . . 29
Safe Operating Area (SOA) curve for ICLS6023J . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
SOA temperature derating coefficient curve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
PG-DIP-8-6 (Pb-free lead plating plastic dual inline outline) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
PG-DSO-16/12 (plastic dual inline). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Marking for ICLS602xX controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
5
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
List of Tables
List of Tables
Table 1
Table 2
Table 3
Data Sheet
Pin Configuration for PG-DIP-8-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Pin Configuration for PG-DSO-16/12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Protection modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
6
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
Current Mode Controllers with Integrated 650 V Startup Cell/Depletion CoolMOS™
Product Highlights
• Constant power
• Adjustable blanking window for high-load jumps to increase reliability
• Frequency jittering for low EMI
• Pb-free lead plating, RoHS-compilant
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Frequency jittering for low EMI
Constant power
650 V avalanche-rugged CoolMOS™ with built-in switchable startup cell
67 kHz fixed switching frequency
Auto Restart mode for overtemperature detection
Auto Restart mode for overvoltage detection
Auto Restart mode for overload and open loop
Auto Restart mode for VCC undervoltage
Floating Load Protection (FLP) mode in the case of open loads
User-defined soft start
Minimum number of external components required
Maximum duty cycle of 75 %
Overall tolerance of current limiting < ± 5 %
Internal leading edge blanking
BiCMOS technology provides a wide VCC range
Data Sheet
7
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
Description
ICLS6x Series controllers employ a fixed-frequency operation mode optimized for offline LED lighting. The
integrated constant power function (patented by Infineon Techologies AG) and the frequency jitter enable high
performance without investment of too much effort in stabilization of the system and filtering in terms of EMC.
A wide VCC range up to 26 V is provided by use of BiCMOS technology to cover changes in the auxiliary supply
voltage if a CV/CC regulation is implemented on the secondary side.
Auto Restart Mode is entered in the case of overtemperature, VCC overvoltage, output open loop or overload and
VCC undervoltage. If an open load event occurs, the device enters the so-called Floating Load Protection (FLP)
mode to protect the LED against destruction. The dimensions of the transformer and the secondary diode can be
reduced owing to the internal precise peak current limitation to yield greater cost efficiency.
20V/350mA
7 VCC
4 D 5 D
ICLS602xX
1 SS
2 FB
Figure 1
PWM
Control
8 GND
3 CS
Typical application of ICLS6x Series controllers
Package
Marking
ICLS6021J
PG-DIP-8-6
ICLS6021J
650 V 67 kHz
6.45 Ω
12 W
5W
ICLS6022J
PG-DIP-8-6
ICLS6022J
650 V 67 kHz
4.70 Ω
17 W
9W
PG-DSO-16/12 ICLS6022G 650 V 67 kHz
4.70 Ω
17 W
9W
1.70 Ω
26 W
15 W
ICLS6022G
ICLS6023J
PG-DIP-8-6
ICLS6023J
VDS
RDSon1) 230 VAC ± 15 %2) 110 VAC ± 15 %2)
Type
FOSC
650 V 67 kHz
1) typ. @ T = 25 °C
2) Calculated maximum input power rating at Ta = 80 °C, Tj = 125 °C and without copper area as heat sink
Data Sheet
8
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
Pin Configuration and Functionality
1
Pin Configuration and Functionality
1.1
Pin Configuration for PG-DIP-8-6
Table 1
Pin Configuration for PG-DIP-8-6
Pin
Symbol
Function
1
SoftS
Soft start
2
FB
Feedback
3
CS
Current Sense / 650 V1) depletion CoolMOS source™
4
Drain
650 V1) depletion CoolMOS source™
5
Drain
650 V1) depletion CoolMOS source™
6
n.c.
Not connected
7
VCC
Controller supply voltage
8
GND
Controller ground
1) @ Tj = 110 °C
1.2
Figure 2
Data Sheet
PG-DIP-8-6 Package
SoftS
1
8
GND
FB
2
7
VCC
CS
3
6
N.C
Drain
4
5
Drain
Pin configuration of PG-DIP-8-6 (top view)
9
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
Pin Configuration and Functionality
1.3
Pin Configuration for PG-DSO-16/12
Table 2
Pin Configuration for PG-DSO-16/12
Pin
Symbol
Function
1
n.c.
Not connected
2
SoftS
Soft start
3
FB
Feedback
4
CS
Current Sense / 650 V1) depletion CoolMOS source™
5
Drain
650 V1) depletion CoolMOS source™
6
Drain
650 V1) depletion CoolMOS source™
7
Drain
650 V1) depletion CoolMOS source™
8
Drain
650 V1) depletion CoolMOS source™
9
n.c.
Not connected
10
n.c.
Not connected
11
VCC
Controller supply voltage
12
GND
Controller ground
1) @ Tj = 110 °C
1.4
PG-DSO-16/12 Package
1
12
GND
SoftS
2
11
VCC
FB
3
10
N.C
CS
4
9
N.C.
Drain
5
8
Drain
Drain
6
7
Drain
N.C
Figure 3
Data Sheet
Pin configuration of PG-DSO-16/12 (top view)
10
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
Pin Configuration and Functionality
1.5
Pin Functionality
SoftS (soft start, auto restart & frequency jittering control)
The SoftS pin combines the soft start function during startup and the error detection function for Auto Restart
mode. These functions are implemented and can be adjusted by means of an external capacitor at the SoftS pin
connected to ground. This capacitor also provides an adjustable blanking window for high load jumps before the
IC enters Auto Restart mode. In addition, this pin is also used to control the period of frequency jittering under
normal loads.
FB (feedback)
The information on the regulation is provided by the FB pin to the internal protection unit and to the internal PWM
comparator to control the duty cycle. In the event of an open load event, the device enters the Floating Load
Protection (FLP) mode.
CS (current sense)
The current sense pin senses the voltage developed on the series resistor inserted into the source of the
integrated depletion CoolMOS™. If CS reaches the internal threshold of the current limit comparator, the driver
output is immediately switched off. The current information is provided to the PWM comparator to realize the
current mode.
Drain (drain of integrated depletion CoolMOS™)
The drain pin provides the connection to the drain of the internal depletion CoolMOS™.
VCC (power supply)
The VCC pin is the positive supply of the IC. The operating range of the supply is between 10.3 V and 26 V.
GND (ground)
The GND pin is the common ground of the controller.
Data Sheet
11
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
Block Diagram
2
Block Diagram
Vcc
Power Management
Control UNIT
Internal
BIAS
Voltage
Reference
Auto Restart
FLP
Power
Down Reset
UVLO
DRAIN
5V
Startup Cell
GND
SS
PROTECTION
OTP
OVP
OCP
OLP
Gate Drive
Soft Start
Current Mode Control
Propagation
Delay
Compensation
PWM
Comparator
FB
Leading
Edge
Blanking
CS
ICLS602xX
Figure 4
Data Sheet
Block diagram of ICLS6x Series controllers
12
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
Functional Description
3
Functional Description
All values used in the functional description are typical values. When calculating the worst cases, the
minimium/maximum values listed in Electrical Characteristics on page 24 have to be considered.
3.1
Introduction
For ICLS6x Series controllers, a high voltage startup cell is integrated into the system IC, which is switched off
once the undervoltage lockout-on threshold of 18 V is exceeded. This startup cell is part of the integrated depletion
CoolMOS™. The external startup resistor is no longer necessary as the startup cell is connected to the drain,
resulting in reduced power losses. This increases the efficiency under light load conditions drastically.
The soft start capacitor is also used for providing an adjustable blanking window for high load jumps. The overload
detection function is disabled during this window. With this concept, no further external components are necessary
to adjust the blanking window.
An Auto Restart mode is implemented in the IC to reduce the average power conversion in the event of malfunction
or unsafe operating conditions in the LED drives. This feature increases the system’s robustness and safety, which
would otherwise lead to a destruction of the LED drive. Once the malfunction is corrected, normal operation is
automatically initiated after the next startup phase.
Together with the soft start capacitor, the feedback can also sense a missing load, which leads to rising output
and auxiliary voltages. This triggers the Floating Load Protection (FLP) mode. When feedback falls below 1.35 V,
the Soft Start voltage begins to rise up to a threshold of 4 V (depends on the C4 value) and the IC is switched into
FLP mode.
The precise internal peak current limitation reduces the costs for the transformer and the secondary diode. The
influence of the change in the input voltage on the power limitation can be avoided together with the integrated
Propagation Delay Compensation circuit. Consequently, the maximum power is practically independent of the
input voltage required for wide range LED drives. There is no need for additional oversizing of the LED drives –
e.g., for the transformer or the secondary diode.
Data Sheet
13
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
Functional Description
3.2
Power Management
Drain
VCC
Startup Cell
Power Management
Undervoltage Lockout
18V
Internal Bias
10.3
Power -Down Reset
Voltage
Reference
5V
Auto Restart
Mode
T1
SoftS
Figure 5
Power management of ICLS6x Series controllers
The undervoltage lockout function monitors the external supply voltage VVCC. When the LED drive is connected to
the main line, the internal startup cell is biased and starts to charge the external capacitor CVCC, which is connected
to the VCC pin. The VCC charge current that is provided by the startup cell from the drain pin is 1.05 mA. If VVCC
exceeds the on-threshold VCCon (= 18 V), the bias circuit is switched on. Then the startup cell is switched off by the
undervoltage lockout; therefore no power losses are present due to the connection of the startup cell to the drain
voltage. An hysteresis loop is implemented to avoid uncontrolled ringing at switch-on. Switch-off of the controller
can only take place after the active mode has been entered and VVCC has fallen below 10.3 V.
The maximum current consumption before the controller is activated is about 300 µA.
If VVCC falls below the off-threshold VCCoff (= 10.3 V), the bias circuit is switched off and a power-down reset causes
discharging of the soft-start capacitor CSoftS at pin SoftS via T4 (see Figure 5). This ensures in every startup cycle
that the voltage ramp at the SoftS pin starts at zero.
The bias circuit is switched off if Auto Restart mode is entered. The current consumption is then reduced to 300 µA.
Once the malfunction condition is resolved, this block will then turn back on. The recovery from Auto Restart mode
does not require disconnection of the LED drive from the AC line.
Data Sheet
14
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
Functional Description
3.3
Startup Phase
3.25kΩ
5V
RSoftS
SoftS
Freq Jitter
Charging
current I FJ
CSoftS
Freq Jitter
Discharging
current I FJ
Soft Start
T2
T3
0.8V
Freq Jitter
Control
Soft-Start
Comparator
C7
Gate Driver
&
G7
C2
3.2V
PWM OP
x3.2
CS
0.6V
Figure 6
Soft start
At the beginning of the startup phase, the IC provides a soft start period during which it controls the maximum
primary current by means of duty cycle limitation. A capacitor CSofts in combination with the internal pull-up resistor
RSoftS determines the duty cycle until VSoftS exceeds 3.2 V.
When the soft start begins, CSoftS is immediately charged up to approx. 0.8 V by T2. The soft start phase takes
place between 0.8 V and 3.2 V. Above VSoftsS = 3.2 V there is no longer any duty cycle limitation DCmax that is
controlled by the comparator C7 since the comparator C2 blocks the gate G7 (see Figure 7). This maximum
charge current in the very first stage when VSoftS is below 0.8 V is limited to 0.9 mA.
VSoftS
max . Startup Phase
4.0V
3.2V
0.8V
max. Soft Start Phase
DCmax
t
DC1
DC2
t1
Figure 7
Data Sheet
t2 t
Startup phase
15
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
Functional Description
As a consequence of this extra charge stage, there is no delay at the beginning of the startup phase when there
is still no switching. Furthermore, soft start is finished at 3.2 V to have maximum power capability even earlier. The
duty cycles DC1 and DC2 vary according to the mains and the primary inductance of the transformer. The limitation
of the primary current by DC2 is related to VSoftS = 3.2 V. However, DC1 is related to a maximum primary current,
which is limited by the internal current limiting function with CS = 1 V. Therefore the maximum startup phase is
divided into a soft start phase until t1 and a phase from t1 to t2 during which maximum power is provided if
demanded by the FB signal.
3.4
PWM Section
0.75
PWM Section
Oscillator
Duty
Cycle
max
Clock
Frequency
Jitter
Soft Start
Comparator
PWM
Comparator
FF1
1
G8
Gate Driver
S
R
Q
&
G9
Current
Limiting
SoftS
Figure 8
PWM section
3.4.1
Oscillator and Jittering
Gate
The oscillator generates a fixed frequency with frequency jittering of ± 4 % from the fixed frequency (i.e., ± 2.7 kHz
for 67 kHz) at a jittering period TFJ. The switching frequency is fswitch = 67 kHz.
A resistor, a capacitor, a current source and current sink for determining the frequency are integrated. The
charging and discharging current of the implemented oscillator capacitor are internally trimmed in order to achieve
a very accurate switching frequency. The ratio of controlled charge to discharge current is adjusted to reach a
maximum duty cycle limitation of Dmax = 0.75.
Once the soft start period is over and the IC has entered normal mode, the soft start capacitor is charged and
discharged through the internal current source IFJ to generate a triangular waveform with a jittering period TFJ,
which is externally adjustable by means of the soft start capacitor, CSoftS (see Figure 6).
TFJ = k FJ ∗ CSoftS
(1)
where kFJ is a constant = 4 ms/µF.
For example: TFJ = 4 ms if CSoftS = 1µF.
Data Sheet
16
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
Functional Description
3.4.2
PWM Latch FF1
The oscillator clock output provides a set pulse to the PWM latch when initiating the internal CoolMOS™
conduction. After being set, the PWM latch can be reset by the PWM comparator, the soft start comparator or the
current limit comparator. In resetting situations the driver is shut down immediately.
3.4.3
Gate Driver
The gate driver is a fast totem pole gate drive designed to avoid cross conduction currents. It is active low at
voltages below the undervoltage lockout threshold VVCCoff.
VCC
PWM Latch
1
Gate
Depl . CoolMOS™
Gate Driver
Figure 9
Data Sheet
Gate driver
17
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
Functional Description
3.5
Current Limiting
PWM Latch
FF1
Current Limiting
Propagation Delay
Compensation
Vc sth
C10
Leading
Edge
Blanking
220 ns
PWM-OP
10kΩ
1pF
D1
CS
Figure 10
Current limiting
Cycle-by-cycle current limiting realized by the current limit comparator C10 to provide overcurrent detection (see
Figure 10). The source current of the integrated depletion CoolMOS™ is sensed by means of an external sense
resistor RSense. By means of RSense the source current is transformed to a sense voltage VSense which is fed to the
CS pin. If VSense exceeds the internal threshold voltage Vcsth the comparator C10 immediately turns off the gate
drive by resetting the PWM latch FF1. A Propagation Delay Compensation circuit is added to support immediate
shutdown without delay of the integrated internal CoolMOS™ in the case of current limiting. The influence of the
AC input voltage on the maximum output power can be suppressed as a result.
To prevent the current limiting function from causing distortions by leading edge spikes, a Leading Edge Blanking
circuit is integrated into the current sense path for the comparator C10 and the PWM OP.
Data Sheet
18
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
Functional Description
3.5.1
Leading Edge Blanking
Each time when the integrated internal CoolMOS™ is switched on, a leading edge spike is generated due to the
primary-side capacitances and secondary-side rectifier reverse recovery time. This spike can cause the gate drive
to switch off unintentionally. To avoid premature termination of the switching pulse, this spike is blanked out with
a time constant of tLEB = 220 ns. During this time, the gate drive will not be switched off. This is illustrated in
Figure 11.
VSense
Vcs th
tLEB = 220ns
t
Figure 11
Leading edge blanking
3.5.2
Propagation Delay Compensation
In the case of overcurrent detection, switch-off of the integrated internal CoolMOS™ is delayed due to the
propagation delay of the circuit. This delay causes an overshoot of the peak current Ipeak, which depends on the
ratio of dI/dt of the peak current (see Figure 12).
Signal2
ISense
Ipeak2
Ipeak1
ILimit
Signal1
tPropagation Delay
IOvershoot 2
IOvershoot 1
t
Figure 12
Peak current overshooting
The overshoot of Signal2 is greater than that of Signal1 due to the steeper rising waveform. This change in the
slope varies according to the AC input voltage. A Propagation Delay Compensation circuit is integrated to limit the
overshoot dependency on dI/dt of the rising primary current. This means that the propagation delay between the
time the current sense threshold Vcsth is exceeded and switch-off of the integrated inernal CoolMOS™ is
compensated over temperature within a wide range.
Data Sheet
19
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
Functional Description
Extremely precise current limiting is now possible.
For example, Ipeak = 0.5 A with RSense = 2 Ω. Without propagation delay compensation the current sense threshold
is set to a static voltage level Vcsth = 1 V. A current ramp of dI/dt = 0.4 A/µs (that means, dVSense/dt = 0.8 V/µs),
and a propagation delay time tPropagation Delay = 180 ns then leads to an Ipeak overshoot of 14.4 %. With propagation
delay compensation the overshoot is only about 2 % (see Figure 13).
without com pensation
with com pensation
V
1, 3
1, 25
VSense
1, 2
1, 15
1, 1
1, 05
1
0, 95
0, 9
0
0,2
0, 4
0, 6
0, 8
1
1, 2
1, 4
1,6
1,8
dVSense
dt
Figure 13
2
V
μs
Overcurrent shutdown
Propagation delay compensation is realized by means of a dynamic threshold voltage Vcsth (see Figure 14). If the
slope is steeper, driver switch-off takes place earlier to compensate for the delay.
VOSC
max. Duty Cycle
off time
V Sense
Propagation Delay
t
Vcsth
Signal1
Figure 14
Data Sheet
Signal2
t
Dynamic voltage threshold Vcsth
20
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
Functional Description
3.6
Control Unit
The Control Unit contains the functions for the Auto Restart and Floating Load Protection (FLP) modes. The Auto
Restart mode is combined with an adjustable blanking window, which varies according to the value of the external
soft start capacitor. The IC avoids entering into either of these two modes accidentally by means of this adjustable
blanking window. The window also provides a certain time during which overload detection is delayed. This delay
is useful for applications that normally work with a low current and occasionally require a short duration of high
current.
3.6.1
Adjustable Blanking Window
VSoftS swings between 3.2 V and 3.6 V after the LED drive has settled and S2 is on while S3 is off. This behavior
is due to the frequency jittering function that makes use of the soft start pin. If overload occurs, VFB exceeds 4.5 V.
The Auto Restart mode cannot be entered as the gate G5 is still blocked by the comparator C3. However, after
VFB has exceeded 4.5 V, the switch S2 is opened and S3 is closed. The external soft start capacitor can then be
further charged by the integrated pull-up resistor RSoftS through the switch S3. The comparator C3 releases the
gate G5 once VSoftS has exceeded 4.0 V. This means that Auto Restart mode cannot be entered during the
charging time of the external capacitor CSoftS.
SoftS
5V
S3
3.0V
RSoftS
Frequency
Jitter
S2
S1
C3
4.0V
&
4.5V
C4
G5
Auto
Restart
Mode
FB
Control Unit
Figure 15
Data Sheet
Adjustable blanking window
21
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
Functional Description
3.6.2
Protection Modes
The IC provides several protection features to increase the LED drive’s robustness and safety. The following table
shows the possible system failures and the corresponding protection modes.
Table 3
Protection modes
VCC Overvoltage
Auto Restart mode during startup
Overtemperature
Auto Restart mode during RUN mode
Overload
Auto Restart mode during RUN mode
Open Loop
Auto Restart mode during RUN mode
VCC Undervoltage
Auto Restart mode during RUN mode
Floating Load Protection (FLP)
Floating Load Protection mode
3.6.2.1
Auto Restart Mode during Startup
The VCC voltage is observed by the comparator C13 if 20.5 V is exceeded. The output of C13 is combined with
both the output of C3, which checks for VSoftS < 4.0 V, and the output of C4, which checks for VFB > 4.5 V.
Therefore, overvoltage detection can only be active during the soft start phase (VSoftS < 4.0 V) and if the FB signal
is outside the operating range (> 4.5 V). This means any small voltage overshoots of VVCC occurring during normal
operation cannot trigger the Auto Restart mode during startup.
SoftS
C3
Auto
Restart
Mode
4.0V
S
R
UVLO
&
Q
FF2
G13
Spike
Blanking
8.0us
VCC
C13
&
20.5V
G12
C4
4.5V
Internal
Bias
Thermal Shutdown
Tj >140°C
Control Unit
FB
Figure 16
Auto Restart mode during startup
In order to ensure system reliability and prevent any false activation, a blanking time is implemented before the IC
can enter Auto Restart mode during startup. The output of the VCC overvoltage detection circuit is fed into a spike
blanking with a time constant of 8.0 µs.
Data Sheet
22
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
Functional Description
The other fault detection function which can result in the Auto Restart mode during startup and has the 8.0 µs
blanking time is for overtemperature detection. This block checks for a junction temperature of higher than 140 °C
for malfunctioning operation.
Once Auto Restart mode is entered, the internal bias is switched off in order to reduce the current consumption of
the IC as much as possible. In this mode, the average current consumption is only 300 µA as the only working
blocks are the reference block and the Undervoltage Lockout (UVLO), which controls the startup cell by switching
on/off at VVCCon/VVCCoff.
As there is no longer a self supply provided by the auxiliary winding, VCC starts to drop. The UVLO switches on
the integrated startup cell when VCC falls below 10.3 V. It continues to charge VCC up to 18 V, at which point it
is switched off again and the IC enters the startup phase.
Once all fault conditions have been removed, the IC automatically powers up as usual with a switching cycle at
the GATE output after the soft start period has elapsed – hence the name Auto Restart mode.
3.6.2.2
Auto Restart Mode during RUN Mode
In the case of overload or open loop, the FB voltage exceeds 4.5 V, which is observed by C4. At this time, the
external soft start capacitor can then be further charged by the integrated pull-up resistor RSoftS via the switch S3
(see Figure 15). If VSoftS exceeds 4.0 V, which is observed by C3, Auto Restart mode during RUN mode is
activated as both inputs of the gate G5 are high.
Internal
Bias
SoftS
C3
4.0V
&
4.5V
C4
G5
Auto
Restart
Mode
FB
Control Unit
Figure 17
Auto Restart mode during RUN mode
This charging of the soft start capacitor from 3.2 V ~ 3.6 V to 4.0 V defines a blanking window, which prevents the
system from entering Auto Restart mode during RUN mode unintentionally during large load jumps. In this event,
FB will rise close to 5.0 V for a short duration before the loop regulates FB to less than 4.5 V.
In the case of VCC undervoltage – i.e., VCC falls below 10.3 V, the IC is turned off with the startup cell charging
VCC as described earlier in this section. Once VCC is charged to above 18 V, the IC starts a new startup cycle.
This blanking time window for the Floating Load Protection mode can be forced via the external CSoftS capacitor.
3.6.2.3
Floating Load Protection (FLP)
The circuit starts up as usual, but a missing load leads to a rise in the output and auxiliary voltages.
Reaching the VCC threshold of 24.5 V (voltage divider RD2/R4 and Q2) leads to a reduction in the feedback
voltage and hence to reduced output current pulses in order to keep the output voltage below the maximum rating
of the components. If the feedback level falls below 1.35 V, the Soft Start voltage begins to rise up to a threshold
of 4 V (depends on the C4 value) and the IC is switched into the FLP mode.
Data Sheet
23
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
Electrical Characteristics
4
Electrical Characteristics
All voltages are measured in respect to ground (GND, pin 8). The voltage levels are valid if other ratings are not
violated.
4.1
Absolute Maximum Ratings
Absolute maximum ratings are defined as ratings, which when exceeded may lead to destruction of the integrated
circuit. For the same reason, ensure that any capacitor to be connected to pin 7 (VCC) is discharged before
assembling the application circuit.
Parameter
Drain/source voltage
Controller
Symbol
Limit Values
min.
max.
Unit
Remarks
ICLS602xX
VDS
–
650
V
ICLS6021J
ID_Puls1
–
1.6
A
ICLS6022J
ID_Puls2
–
2.3
A
ICLS6022G
ID_Puls3
–
2.3
A
ICLS6023J
ID_Puls4
–
6.1
A
ICLS6021J
EAR1
–
0.005
mJ
ICLS6022J
EAR2
–
0.01
mJ
ICLS6022G
EAR3
–
0.01
mJ
ICLS6023J
EAR4
–
0.15
mJ
ICLS6021J
IAR1
–
0.3
A
ICLS6022J
IAR2
–
0.5
A
ICLS6022G
IAR3
–
0.5
A
ICLS6023J
IAR4
–
1.5
A
VCC supply voltage
ICLS602xX
VVCC
-0.3
27
V
FB voltage
ICLS602xX
VFB
-0.3
5.0
V
SoftS voltage
ICLS602xX
VSoftS
-0.3
5.0
V
CS voltage
ICLS602xX
VCS
-0.3
5.0
V
Junction temperature
ICLS602xX
Tj
-40
150
°C
Storage temperature
ICLS602xX
TS
-55
150
°C
Thermal resistance
– junction ambient
ICLS602xX
RthJA
–
90
K/W
PG-DIP-8-6
–
110
K/W
PG-DSO-16/12
ESD capability
ICLS602xX
VESD
–
2
kV
Pulse drain current, tp
limited by max. Tj = 150 °C
Avalanche energy,
repetitive tAR limited by max.
Tj = 150 °C1)
Avalanche current,
repetitive tAR limited by max.
Tj=150 °C1)
Tj = 110°C
Controllers & CoolMOS™
Human body model2)
1) Repetetive avalanche causes additional power losses that can be calculated as PAV = EAR* f
2) According to EIA/JESD22-A114-B (discharging a 100 pF capacitor through a 1.5 kΩ series resistor)
Data Sheet
24
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
Electrical Characteristics
4.2
Operating Range
The IC operates as described in the functional description once the values listed here lie within the operating
range.
Parameter
Symbol
Limit Values
min.
max.
Unit
VCC supply voltage
VVCC
VVCCoff
26
V
Junction temperature of controller
TjCon
–25
130
°C
TJCoolMOS
–25
150
°C
Junction temperature of
CoolMOS™
4.3
Characteristics
4.3.1
Supply Section
Remarks
Max. value limited due to
integrated thermal shutdown
The electrical characteristics involve the spread of values guaranteed within the specified supply voltage and
junction temperature range TJ from –25 °C to 130 °C. Typical values represent the median values, which are
related to 25 °C. Unless otherwise stated, a supply voltage of VCC = 18 V is assumed.
Parameter
Startup current
VCC charge current
Symbol
IVCCstart
Limit Values
Unit
Remarks
min.
typ.
max.
–
300
450
µA
VVCC = 17 V
5.0
mA
VVCC = 0 V
IVCCcharge1
IVCCcharge2
0.55
1.05
1.60
mA
VVCC = 1 V
IVCCcharge3
–
0.88
–
mA
VVCC = 17 V
Leakage current of the
startup cell & CoolMOS™
IStartLeak
–
0.2
50
µA
VDrain= 450 V
at Tj = 100 °C
Supply current with
inactive gate
IVCCsup1
–
1.7
2.5
mA
Soft Start pin is open
Supply current with active gate
IVCCsup3
–
2.5
3.6
mA
VSoftS = 3.0 V
IFB = 0
Supply current in Auto Restart
mode with inactive gate
IVCCrestart
–
300
–
µA
IFB = 0
ISoftS = 0
Supply current in Floating Load
Protection (FLP) mode with
inactive gate
IVCCFLP1
–
500
950
µA
VFB = 2.5 V
ISoftS = 3.0 V
–
500
950
µA
VCC = 11.5 V
VFB = 2.5 V
ISoftS = 3.0 V
18.0
10.3
7.7
19.0
11.0
–
V
V
V
VCC turn-on threshold
VCC Turn-off threshold
VCC Turn-on/off hysteresis
Data Sheet
IVCCFLP2
VVCConVVCCo 17.0
9.6
ffVVCChys
–
25
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
Electrical Characteristics
4.3.2
Internal Voltage Reference
Parameter
Symbol
Trimmed reference voltage
4.3.3
VREF
Limit Values
min.
typ.
max.
4.90
5.00
5.10
Unit
V
Remarks
measured at pin FB
IFB = 0
PWM Section
Parameter
Symbol
Limit Values
Unit
Remarks
min.
typ.
max.
fOSC3
58
67
76
kHz
fOSC4
62
67
74.5
kHz
Tj = 25 °C
Frequency jittering range
fdelta
–
±2.7
–
kHz
Tj = 25 °C
Max. duty cycle
Dmax
0.70
0.75
0.80
Min. duty cycle
Dmin
0
–
–
PWM OP gain
AV
3.0
3.2
3.4
VMax-Ramp
–
0.6
–
V
VFB operating range, min. level
VFBmin
–
0.5
–
V
VFB operating range, max. level
VFBmax
–
–
4.3
V
Feedback pull-up resistor
RFB
9
14
22
kΩ
Soft start pull-up resistor
RSoftS
30
45
62
kΩ
Fixed oscillator frequency
Max. level of voltage ramp
VFB < 0.3 V
CS=1V limited by comparator C41)
1) This parameter is not subject to production testing and is verified by design/characterization
Data Sheet
26
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
Electrical Characteristics
4.3.4
Control Unit
Parameter
Symbol
Deactivation level for SoftS
comparator C7 by C2
Limit Values
min.
typ.
max.
2.98
3.10
3.22
V
VSoftSclmp_FLP 2.88
3.0
3.12
V
VSoftSC2
Clamped VSoftS voltage during
Floating Load Protection (FLP)
mode
Unit
Remarks
VFB = 5 V
Activation limit of
comparator C3
VSoftSC3
3.85
4.00
4.15
V
SoftS startup current
ISoftSstart
–
0.9
–
mA
Overload detection limit for
comparator C4
VFBC4
4.33
4.50
4.67
V
VSoftS = 4.5 V
Floating Load Protection level for
comparator C5
VFBC5
1.23
1.35
1.43
V
VSoftS = 4.5 V
Floating Load Protection level for
comparator C6a
VFBC6a
3.48
3.61
3.76
V
After Floating Load Protection
mode is entered
Floating Load Protection level for
comparator C6b
VFBC6b
2.88
3.0
3.12
V
After Floating Load Protection
mode is entered
VVCCOVP
19.5
20.5
21.5
V
VFB = 5 V, VSoftS = 3 V
Thermal shutdown
TjSD
130
140
150
°C
Spike blanking
tSpike
–
8.0
–
µs
Overvoltage detection limit
1)
VFB = 5 V
VSoftS = 0 V
1) The parameter is not subject to production testing and is verified by design/characterization
Note: The trend of all the voltage levels in the Control Unit is the same regarding the deviation except VVCCOVP.
4.3.5
Current Limiting
Parameter
Symbol
Limit Values
Unit
Remarks
min.
typ.
max.
1.01
1.06
1.11
V
dVsense / dt = 0.6 V/µs (PG-DIP-8-6)
1.02
1.07
1.12
V
dVsense / dt = 0.6 V/µs (PG-DSO-16/12)
Peak current limitation (incl.
propagation delay time)
(see Figure 13)
Vcsth
Peak current limitation during
Floating Load Protection mode
VCS2
0.27
0.32
0.37
V
Leading edge blanking
tLEB
–
220
–
ns
VSoftS = 3.0 V
ICSbias
–1.0
–0.2
0
µA
VCS = 0 V
CS input bias current
Data Sheet
27
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
Electrical Characteristics
4.3.6
CoolMOS™ Section
Parameter
Drain/source breakdown
voltage
Drain/source on resistance
Effective output
capacitance, energy-related
Rise time
Fall time
Controller
Symbol
Limit Values
min.
typ.
max.
–
–
–
–
Unit
ICLS602xX
V(BR)DSS
600
650
ICLS6021J
RDSon1
–
–
ICLS6022J
ICLS6022G
RDSon2
–
–
ICLS6023J
RDSon3
–
–
ICLS6021J
Co(er)1
–
3.65
–
pF
ICLS6022J
Co(er)2
–
4.75
–
pF
ICLS6022G
Co(er)3
–
4.75
–
pF
ICLS6023J
Co(er)4
–
11.63
ICLS602xX
ICLS602xX
trise
–
tfall
–
Remarks
V
V
Tj = 25 °C
Tj = 110 °C
6.45 7.50
13.70 17.00
Ω
Ω
Tj = 25 °C
Tj = 125 °C1)
at ID = 0.3 A
4.70 5.44
10.00 12.50
Ω
Ω
Tj = 25 °C
Tj = 125 °C1)
at ID = 0.5 A
Ω
Ω
Tj = 25 °C
Tj = 125 °C1)
at ID = 1.5 A
1.70
3.57
1.96
4.12
–
pF
30
2)
–
ns
30
2)
–
ns
VDS = 0 V to 480 V
1) The parameter is not subject to production testing and is verified by design/characterization
2) Measured in a typical flyback converter application
Data Sheet
28
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
Temperature Derating Curves
5
Temperature Derating Curves
ICLS6021J
Figure 18
Safe Operating Area (SOA) curve for ICLS6021J
ICLS6022J and ICLS6022G
Figure 19
Data Sheet
Safe Operating Area (SOA) curve for ICLS6022J and ICLS6022G
29
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
Temperature Derating Curves
ICLS6021J
Figure 20
Safe Operating Area (SOA) curve for ICLS6023J
ICLS602xX
Figure 21
Data Sheet
SOA temperature derating coefficient curve
30
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
Outline Dimensions
6
Outline Dimensions
6.1
Outline Dimensions of PG-DIP-8-6
Figure 22
PG-DIP-8-6 (Pb-free lead plating plastic dual inline outline)
6.2
Outline Dimensions of PG-DSO-16/12
PG-DSO-16/12
(Plastic Dual In-Line Outline)
Figure 23
Data Sheet
PG-DSO-16/12 (plastic dual inline)
31
Version 1.0, 2011-05-19
LED System Driver ICs
ICLS6x Series
Marking
7
Marking
ICLS602xX
Figure 24
Data Sheet
Marking for ICLS6x Series controllers
32
Version 1.0, 2011-05-19
w w w . i n f i n e o n . c o m
Published by Infineon Technologies AG