规格书编号 SPEC NO : 产品 规 格书 SPECIFICATION CUSTOMER 客 户： PRODUCT 产 品： SAW FILTER MODEL NO 型 号： HDF404.5AT SMD-3 PREPARED 编 制： CHECKED 审 核： APPROVED 批 准： D A T E 日 期： 2008-8-14 客户确认 CUSTOMER RECEIVED: 审核 CHECKED 批准 APPROVED 日期 DATE 无锡市好达电子股份有限公司 Shoulder Electronics Limited www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 1 of 8 SAW FILTER HDF404.5AT SMD-3 更改历史记录 History Record 更改日期 Date www.shoulder.cn 规格书编号 Spec. No. 产品型号 Part No. 客户产品型号 Customer No. Tel:0755-82916880 Fax:0755-82916881 更改内容描述 Modify Content E-mail:[email protected] 备注 Remark Page 2 of 8 SAW FILTER HDF404.5AT SMD-3 1. SCOPE This specification shall cover the characteristics of SAW filter With F404.5AT used for the page system. 2. ELECTRICAL SPECIFICATION AC Voltage Vpp Operation temperature Storage temperature RF Power Dissipation 10V50Hz/60Hz -20℃ to +60℃ -45℃ to +85℃ 27dBm Electronic Characteristics 2-1.Typical frequency response 2-2.Electrical characteristics Part number Nominal center frequency (Fo) Insertion Loss(403.0~406.0MHz) 0~380MHz 430 MHz ~1700MHz 1700MHz~2500MHz 409.5MHz 413.0 MHz ~416.0MHz Ripple (in passband) VSWR Input/Output Impedance(Nominal) www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 F404.5AT 404.5 3.5max 20min 20min 18min 12min 35min 1.0max 2.0max 50//0 E-mail:[email protected] Unit MHz dB dB dB dB dB dB dB Ω/pF Page 3 of 8 SAW FILTER HDF404.5AT SMD-3 3. TEST CIRCUIT 4. DIMENSION 1.Ground 2.Input/output 3.Ground 4.Ground 5.Ground 6.Input/output 7.Ground 8.Ground 5. ENVIRONMENTAL CHARACTERISTICS 5-1 High temperature exposure Subject the device to +85℃ for 16 hours. Then release the filter into the room conditions for 24 hours prior to the measurement. It shall fulfill the specifications in table 1. 5-2 Low temperature exposure Subject the device to -20℃ for 16 hours. Then release the device into the room conditions for 24 hours prior to the measurement. It shall fulfill the specifications in table 1. 5-3 Temperature cycling Subject the device to a low temperature of -40℃ for 30 minutes. Following by a high temperature of +80℃ for 30 Minutes. Then release the device into the room conditions for 24 hours prior to the measurement. It shall meet the specifications in table 1. 5-4 Resistance to solder heat Dip the device terminals no closer than 1.5mm into the solder bath at 260℃ ±10℃ for 10±1 sec. Then release the device into the room conditions for 4 hours. The device shall www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 4 of 8 SAW FILTER HDF404.5AT SMD-3 meet the specifications in table 1. 5-5 Solderability Subject the device terminals into the solder bath at 245℃±5℃ for 5s, More than 95% area of the terminals must be covered with new solder. It shall meet the specifications in table 1. 5-6 Mechanical shock Drop the device randomly onto the concrete floor from the height of 1m 3 times. the device shall fulfill the specifications in table 1. 5-7 Vibration Subject the device to the vibration for 1 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 Hz. The device shall fulfill the specifications in table 1. 5-8 Lead fatigue 5-8-1 Pulling test Weight along with the direction of lead without an shock 1kg. The device shall satisfy all the initial Characteristics. 5-8-2 Bending test Lead shall be subject to withstand against 90℃ bending with 450g weight in the direction of thickness. This operation shall be done toward both direction. The device shall show no evidence of damage and shall satisfy all the initial electrical characteristics. 6. REMARK 6.1 Static voltage Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 6.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning 6.3 Soldering Only leads of component may be soldered. Please avoid soldering another part of component. 7. Packing 7.1 Dimensions (1) Carrier Tape: Figure 1 (2) Reel: Figure 2 (3) The product shall be packed properly not to be damaged during transportation and storage. 7.2 Reeling Quantity 1000 pcs/reel 7’’ 3000 pcs/reel 13’’ 7.3 Taping Structure (1) The tape shall be wound around the reel in the direction shown below. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 5 of 8 SAW FILTER HDF404.5AT SMD-3 (2) Label Device Name User Product Name Quantity Lot No. (3) Leader part and vacant position specifications. 8. TAPE SPECIFICATIONS 8.1 Tensile Strength of Carrier Tape: 4.4N/mm width 8.2 Top Cover Tape Adhesion (See the below figure) (1) pull off angle: 0~15º (2) speed: 300mm/min. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 6 of 8 SAW FILTER HDF404.5AT SMD-3 (3) force: 20~70g [Figure 1] Carrier Tape Dimensions [Unit:mm] W F E P0 P1 P2 D0 D1 t1 t2 A B 12.0 ±0.3 5.5 ±0.05 1.75 ±0.1 4.0 ±0.1 8.0 ±0.1 2.0 ±0.05 Ø1.5 ±0.1 Ø1.0 ±0.25 0.3 ±0.05 2.10 ±0.1 6.40 ±0.1 5.20 ±0.1 [Figure 2] www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 7 of 8 SAW FILTER HDF404.5AT SMD-3 [Unit:mm] A B C D E W t r Ø330 ±1.0 Ø100 ±0.5 Ø13 ±0.5 Ø21 ±0.8 2 ±0.5 13 ±0.3 3 max. 1.0 max. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 8 of 8