Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products. REMINDERS ■ Product information in this catalog is as of October 2013. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or usage of the Products. Please note that TAIYO YUDEN CO., LTD. shall not be responsible for any defects in products or equipment incorporating such products, which are caused under the conditions other than those specified in this catalog or individual specification. ■ Please contact TAIYO YUDEN CO., LTD. for further details of product specifications as the individual specification is available. ■ Please conduct validation and verification of products in actual condition of mounting and operating environment before commercial shipment of the equipment. ■ All electronic components or functional modules listed in this catalog are developed, designed and intended for use in general electronics equipment.(for AV, office automation, household, office supply, information service, telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have direct influence to harm or injure a human body, please contact TAIYO YUDEN CO., LTD. for more detail in advance. Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, submarine system, military, etc. where higher safety and reliability are especially required. In addition, even electronic components or functional modules that are used for the general electronic equipment, if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliability evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to install a protective circuit is strongly recommended at customer's design stage. ■ The contents of this catalog are applicable to the products which are purchased from our sales offices or distributors (so called TAIYO YUDEN s official sales channel ). It is only applicable to the products purchased from any of TAIYO YUDEN s official sales channel. ■ Please note that TAIYO YUDEN CO., LTD. shall have no responsibility for any controversies or disputes that may occur in connection with a third party's intellectual property rights and other related rights arising from your usage of products in this catalog. TAIYO YUDEN CO., LTD. grants no license for such rights. ■ Caution for export Certain items in this catalog may require specific procedures for export according to Foreign Exchange and Foreign Trade Control Law of Japan, U.S. Export Administration Regulations , and other applicable regulations. Should you have any question or inquiry on this matter, please contact our sales staff. 14 MULTILAYER CHIP BEAD INDUCTORS(BK SERIES) MULTILAYER CHIP BEAD INDUCTORS (BK SERIES) ■PARTS NUMBER B K △ ① 1 6 0 8 H S 1 ③ 2 1 ④ － T △ ⑤ ⑥ ⑦ Multilayer chip bead inductor ／ FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS Code Type（inch） 0402 0603 1005 1608 2125 0402（01005） 0603（0201） 1005（0402） 1608（0603） 2125（0805） △＝Blank space ④Nominal impedance Code （example） 150 101 102 Series name ②Dimensions（L×W） ③Material Code HW HS HR HM LM LL TS TM REFLOW *Operating Temp. : -55～+125℃ ② ①Series name Code BK△ BKH WAVE＊ ＊Except for BK0402, BK0603, BK1005, BKH1005 Dimensions （L×W）［mm］ 0.4×0.2 0.6×0.3 1.0×0.5 1.6×0.8 2.0×1.25 ⑤Characteristics Code － ⑥Packaging Code T 15 100 1000 Characteristics Standard Packaging Taping ⑦Internal code Code △ Material Nominal impedance［Ω］ Internal code Standard Refer to impedance curves for material differences ■STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY Type BK 0402 （01005） BK 0603 BKH0603 （0201） BK 1005 BKH1005 （0402） BK 1608 （0603） BK 2125 （0805） Standard quantity [pcs] Paper tape Embossed tape L W T e 0.40±0.02 （0.016±0.001） 0.20±0.02 （0.008±0.001） 0.20±0.02 （0.008±0.001） 0.10＋0.04/－0.03 （0.004＋0.002/－0.001） 20000 － 0.60±0.03 （0.024±0.001） 0.30±0.03 （0.012±0.001） 0.30±0.03 （0.012±0.001） 0.15±0.05 （0.006±0.002） 15000 － 1.00±0.05 （0.039±0.002） 0.50±0.05 （0.020±0.002） 0.50±0.05 （0.020±0.002） 0.25±0.10 （0.010±0.004） 10000 － 1.6±0.15 （0.063±0.006） 2.0＋0.3/－0.1 （0.079＋0.012/－0.004） 2.0＋0.3/－0.1 （0.079＋0.012/－0.004） 0.8±0.15 （0.031±0.006） 1.25±0.2 （0.049±0.008） 1.25±0.2 （0.049±0.008） 0.8±0.15 （0.031±0.006） 0.85±0.2 （0.033±0.008） 1.25±0.2 （0.049±0.008） 0.3±0.2 （0.012±0.008） 0.5±0.3 （0.020±0.012） 0.5±0.3 （0.020±0.012） 4000 － 4000 － － 2000 Unit：mm（inch） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please checki_mlci_BK_e-E02R01 our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 92 14 ■PARTS NUMBER ●BK 0402 Parts number BK 0402HS100-T BK 0402HS700-T BK 0402HS121-T BK 0402HM100-T BK 0402HM750-T BK 0402HM121-T BK 0402HM151-T BK 0402HM181-T BK 0402LL220-T EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Nominal impedance ［Ω］ 10 70 120 10 75 120 150 180 22 Impedance tolerance ±5Ω ±25％ ±25％ ±5Ω ±25％ ±25％ ±25％ ±25％ ±25％ Measuring frequency ［MHz］ 100 100 100 100 100 100 100 100 100 DC Resistance ［Ω］（max.） 0.10 0.37 0.53 0.07 0.45 0.60 0.65 0.75 0.70 Rated current ［mA］（max.） 540 280 240 750 260 220 200 200 150 Thickness ［mm］ 0.20 ±0.02 0.20 ±0.02 0.20 ±0.02 0.20 ±0.02 0.20 ±0.02 0.20 ±0.02 0.20 ±0.02 0.20 ±0.02 0.20 ±0.02 Measuring frequency ［MHz］ 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 DC Resistance ［Ω］（max.） 0.065 0.070 0.40 0.45 0.65 1.20 0.25 0.40 0.80 1.05 1.20 0.25 0.45 0.55 0.70 1.00 1.30 1.50 0.18 0.23 0.32 0.75 0.18 0.23 0.38 0.85 1.50 2.50 3.20 Rated current ［mA］（max.） 500 500 200 200 200 150 200 200 200 100 100 200 200 150 150 100 100 100 500 450 400 270 450 400 300 250 160 130 115 Thickness ［mm］ 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 0.30 ±0.03 Measuring frequency ［MHz］ 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 DC Resistance ［Ω］（max.） 0.17 0.24 0.31 0.50 0.60 0.03 0.06 0.10 0.10 0.20 0.30 0.45 0.55 0.58 0.60 0.18 0.18 0.30 0.45 0.50 0.70 0.11 0.18 0.25 0.33 0.31 0.45 0.50 0.70 0.90 0.85 1.25 1.50 2.00 Rated current ［mA］（max.） 500 450 400 350 300 1,000 700 700 700 500 400 350 300 300 300 350 300 300 250 250 150 500 400 400 350 400 350 300 250 120 300 250 200 200 Thickness ［mm］ 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 0.50 ±0.05 ●BK 0603 EHS BK 0603HS220-T BK 0603HS330-T BK 0603HS800-T BK 0603HS121-T BK 0603HS241-T BK 0603HS601-T BK 0603HM600-T BK 0603HM121-T BK 0603HM241-T BK 0603HM471-T BK 0603HM601-T BK 0603LL100-T BK 0603LL220-T BK 0603LL330-T BK 0603LL470-T BK 0603LL560-T BK 0603LL800-T BK 0603LL121-T BK 0603TS800-T BK 0603TS121-T BK 0603TS241-T BK 0603TS601-T BK 0603TM800-T BK 0603TM121-T BK 0603TM241-T BK 0603TM601-T BKH0603LM601-T BKH0603LM102-T BKH0603LM152-T RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Nominal impedance ［Ω］ 22 33 80 120 240 600 60 120 240 470 600 10 22 33 47 56 80 120 80 120 240 600 80 120 240 600 600 1000 1500 Impedance tolerance ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ●BK 1005 Parts number EHS BK 1005HW680-T BK 1005HW121-T BK 1005HW241-T BK 1005HW431-T BK 1005HW601-T BK 1005HS100-T BK 1005HS330-T BK 1005HS680-T BK 1005HS800-T BK 1005HS121-T BK 1005HS241-T BK 1005HS431-T BK 1005HS601-T BK 1005HS102-T BK 1005HR601-T BK 1005HM750-T BK 1005HM121-T BK 1005HM241-T BK 1005HM471-T BK 1005HM601-T BK 1005HM102-T BK 1005LL100-T BK 1005LL220-T BK 1005LL330-T BK 1005LL470-T BK 1005LL680-T BK 1005LL121-T BK 1005LL181-T BK 1005LL241-T BK 1005LM182-T BKH1005LM601-T BKH1005LM102-T BKH1005LM152-T BKH1005LM182-T RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Nominal impedance ［Ω］ 68 120 240 430 600 10 33 68 80 120 240 430 600 1000 600 75 120 240 470 600 1000 10 22 33 47 68 120 180 240 1800 600 1000 1500 1800 Impedance tolerance ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ／ FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS Parts number i_mlci_BK_e-E02R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 14 93 ■PARTS NUMBER ●BK 1608 Parts number ／ FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS BK 1608HW121-T BK 1608HW241-T BK 1608HW431-T BK 1608HW601-T BK 1608HS220-T BK 1608HS330-T BK 1608HS470-T BK 1608HS600-T BK 1608HS800-T BK 1608HS121-T BK 1608HS241-T BK 1608HS601-T BK 1608HS102-T BK 1608HM121-T BK 1608HM241-T BK 1608HM471-T BK 1608HM601-T BK 1608HM102-T BK 1608LL300-T BK 1608LL470-T BK 1608LL560-T BK 1608LL680-T BK 1608LL121-T BK 1608LL181-T BK 1608LL241-T BK 1608LL331-T BK 1608LL431-T BK 1608LL511-T BK 1608LL681-T BK 1608LM751-T BK 1608LM152-T BK 1608LM182-T BK 1608LM252-T BK 1608TS431-T BK 1608TS601-T BK 1608TS102-T EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Nominal impedance ［Ω］ 120 240 430 600 22 33 47 60 80 120 240 600 1000 120 240 470 600 1000 30 47 56 68 120 180 240 330 430 510 680 750 1500 1800 2500 430 600 1000 Impedance tolerance ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ Measuring frequency ［MHz］ 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 DC Resistance ［Ω］（max.） 0.15 0.25 0.30 0.40 0.05 0.08 0.10 0.10 0.10 0.18 0.25 0.45 0.60 0.20 0.35 0.45 0.60 0.70 0.20 0.30 0.30 0.35 0.50 0.65 0.80 0.85 0.85 0.90 1.00 0.60 0.75 0.85 1.10 0.21±30％ 0.27±30％ 0.30±30％ Rated current ［mA］（max.） 600 450 400 300 1,500 1,200 900 800 600 500 400 350 300 350 300 250 250 200 500 400 400 300 300 250 250 200 200 200 150 300 250 200 200 400 350 300 Thickness ［mm］ 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 0.80 ±0.15 Measuring frequency ［MHz］ 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 DC Resistance ［Ω］（max.） 0.05 0.05 0.05 0.05 0.10 0.10 0.15 0.20 0.25 0.30 0.40 0.15 0.20 0.25 0.25 0.35 0.20 0.30 0.35 0.30 0.35 0.45 0.75 Rated current ［mA］（max.） 1,200 1,200 1,200 1,000 1,000 900 800 600 500 500 300 800 600 500 500 400 600 400 300 400 400 300 200 Thickness ［mm］ 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 0.85 ±0.2 1.25 ±0.2 1.25 ±0.2 ●BK 2125 Parts number BK 2125HS150-T BK 2125HS220-T BK 2125HS330-T BK 2125HS470-T BK 2125HS750-T BK 2125HS101-T BK 2125HS121-T BK 2125HS241-T BK 2125HS431-T BK 2125HS601-T BK 2125HS102-T BK 2125HM121-T BK 2125HM241-T BK 2125HM471-T BK 2125HM601-T BK 2125HM102-T BK 2125LL560-T BK 2125LL121-T BK 2125LL241-T BK 2125LM751-T BK 2125LM152-T BK 2125LM182-T BK 2125LM252-T EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Nominal impedance ［Ω］ 15 22 33 47 75 100 120 240 430 600 1000 120 240 470 600 1000 56 120 240 750 1500 1800 2500 Impedance tolerance ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ ±25％ i_mlci_BK_e-E02R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 94 14 ■ ELECTRICAL CHARACTERISTICS ■ BK0402 BK0402 HS700 80 200 200 25 60 40 10 100 1000 Frequency [MHz] 0 10000 Ｒ 10 100 1000 Frequency [MHz] 0 10000 15 Ｚ 10 Ｒ 250 200 200 150 Ｚ Ｒ 10 100 1000 Frequency [MHz] BK0402 HM151 350 Ｘ 10 100 1000 Frequency [MHz] 10 100 1000 Frequency [MHz] 10000 BK0402 HM181 450 300 350 150 Ｚ Ｒ 100 0 10000 1 400 250 Ｚ Ｒ 200 150 100 Ｘ 50 50 0 10000 1 10 100 1000 Frequency [MHz] Ｒ 200 150 Ｘ 50 0 1 10000 250 100 50 Ｘ Ｚ 300 10 100 1000 Frequency [MHz] 0 10000 1 10 100 1000 Frequency [MHz] 10000 ■ BK0603 BK0603 HS220 250 Impedance ［Ω］ Ｒ 150 Ｚ 100 100 80 80 200 60 150 60 40 Ｚ 20 Ｒ 50 0 Ｘ 1 10 100 1000 Frequency [MHz] 0 10000 0 10000 X 1 10 100 1000 Frequency［MHz］ 10000 BK0603 HS601 1000 200 800 200 600 150 Impedance ［Ω］ 250 R Z 50 200 100 1000 1 10000 500 200 400 Impedance ［Ω］ 250 150 100 50 10 100 1000 BK0603 LL100 250 1000 0 10000 R 200 X 1 BK0603 LL220 Z 50 100 Z 10 100 1000 Frequency［MHz］ 10000 0 400 1 10 100 1000 Frequency［MHz］ 1 10 100 1000 10000 BK0603 HM601 1 600 Z 400 R 200 Ｘ Ｘ 10 100 1000 Frequency［MHz］ 0 10000 BK0603 LL330 BK0603 LL470 500 400 300 200 Z Ｒ 300 Z 200 X X 10000 0 R 100 Ｘ R 1 R 100 50 X Ｒ 10000 800 400 150 1000 1000 Z 500 Impedance ［Ω］ Impedance ［Ω］ 100 10000 BK0603 HM471 600 0 10000 200 150 10 100 1000 Frequency［MHz］ 200 10 100 1000 Frequency［MHz］ 100 50 X 800 250 200 1 1000 Z 300 0 10000 100 BK0603 HM241 100 1 10 Impedance ［Ω］ 10 R 10 100 Z X 1 0 400 1 250 Impedance[ ] 100 R Z 50 X 10 100 1000 Frequency [MHz] 150 Impedance ［Ω］ 100 Z R 20 Ｘ 1 40 250 Impedance ［Ω］ Impedance ［Ω］ 200 BK0603 HS330 100 Impedance ［Ω］ BK0402 LL220 ／ FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS Impedance ［Ω］ 250 Ｘ Ｘ 1 BK0402 HM121 300 1 20 50 Ｘ 1 BK0402 HM750 100 Ｚ 100 BK0402 HM100 5 300 0 Ｒ 50 Ｒ Ｘ 1 Ｚ Impedance ［Ω］ 0 100 150 Impedance ［Ω］ Ｚ 150 Impedance ［Ω］ 30 Impedance ［Ω］ 250 20 Impedance ［Ω］ BK0402 HS121 250 Impedance ［Ω］ Impedance ［Ω］ BK0402 HS100 100 1 10 100 1000 Frequency［MHz］ 10000 0 1 10 100 1000 Frequency［MHz］ 10000 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 14 95 ■ ELECTRICAL CHARACTERISTICS BK0603 LL560 500 BK0603 LL800 1000 BK0603 LL121 1000 BK0603 TS800 200 Z 1 0 10000 BK0603 TS121 250 Impedance ［Ω］ BK0603 TS241 1 10 100 1000 Frequency［MHz］ Ｚ 200 BK0603 TM121 1 10 100 1000 Frequency［MHz］ 0 BK0603 TM241 Impedance ［Ω］ Ｚ 100 Ｒ Ｚ 200 50 100 Ｘ 1 10 100 1000 Frequency［MHz］ 0 10000 10 100 1000 Frequency［MHz］ 0 10000 BK0603 TM601 1 10 100 1000 Frequency［MHz］ 10000 X 1 10 100 1000 Frequency［MHz］ 10000 BK0603 LM601 2000 1500 Ｚ 400 0 R Z 50 Ｚ 1000 200 Ｒ 10000 BK0603 TM800 100 Ｘ 1 600 Ｘ 10 100 1000 Frequency［MHz］ Ｒ 800 300 X 1 200 Ｚ 1000 400 150 0 10000 150 200 10000 R 50 BK0603 TS601 400 Ｒ 500 200 10 100 1000 Frequency［MHz］ 600 Ｘ Z Ｘ 1 1000 300 0 10000 100 800 100 Ｘ 250 Impedance ［Ω］ 0 10000 Impedance ［Ω］ Impedance ［Ω］ Ｒ 50 Ｘ 1 Ｒ 500 Ｘ Ｒ 10 100 1000 Frequency［MHz］ 0 10000 1 10 100 1000 Frequency［MHz］ 10000 ■ BK1005 1000 500 1000 Ｘ 1 10 100 1000 Frequency［MHz］ 0 10000 1 10 100 1000 Frequency［MHz］ Z R 100 400 Z 1 10000 R Z 20 100 Z Ｒ 50 10 100 R 1 10 100 1000 Frequency［MHz］ 1000 10000 0 1 10 100 1000 Frequency［MHz］ 10000 60 40 10000 0 Z R 1 X 10 100 1000 Frequency［MHz］ 10000 250 200 200 150 150 100 100 Z 50 R 50 X X Frequency［MHz］ 10 100 1000 Frequency［MHz］ BK1005 HS100 20 BK1005 HS800 250 150 X 1 Z 400 10000 Impedance ［Ω］ 40 1 80 600 0 200 60 0 10 100 1000 Frequency［MHz］ Ｘ X BK1005 HS680 250 Impedance ［Ω］ Impedance ［Ω］ 1 Ｒ 100 200 BK1005 HS330 80 10000 BK1005 HW601 X 10 100 1000 Frequency［MHz］ 100 R 200 0 0 800 600 Ｚ 100 X 10 100 1000 Frequency［MHz］ 1000 X 0 1 150 50 R BK1005 HW431 Impedance ［Ω］ Impedance ［Ω］ 200 Z 10000 800 300 100 0 1000 400 150 50 Ｘ 500 BK1005 HW241 500 Ｒ 1500 200 Impedance ［Ω］ Ｒ BK1005 HW121 250 200 2000 Impedance ［Ω］ 1500 BK1005 HW680 250 Ｚ Ｚ Impedance ［Ω］ Impedance ［Ω］ 3000 2500 2000 0 BKH0603 LM152 Impedance ［Ω］ BKH0603 LM102 2500 Impedance ［Ω］ ／ FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS Ｚ 100 0 1 400 150 0 200 X 10 100 1000 Frequency［MHz］ 500 200 Impedance ［Ω］ 200 X 10 100 1000 Frequency［MHz］ Ｒ 400 Impedance ［Ω］ 0 R Z Impedance ［Ω］ 100 Z 400 150 600 Impedance ［Ω］ 200 800 600 Impedance ［Ω］ 800 R 300 Impedance ［Ω］ Impedance ［Ω］ 400 10000 0 0 1 10 100 1000 Frequency［MHz］ 10000 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 96 14 ■ ELECTRICAL CHARACTERISTICS BK1005 HS431 1000 BK1005 HS102 2000 Impedance ［Ω］ Impedance ［Ω］ 800 600 400 Z 1000 Z 200 0 1 R X 10 100 1000 Frequency［MHz］ BK1005 HR601 0 10000 BK1005 HM750 1000 200 800 Impedance ［Ω］ 600 100 50 0 10000 10 10000 400 Z 150 300 R 200 100 100 50 0 0 1 X 10 100 1000 Frequency［MHz］ 0 10000 1 BK1005 HM102 100 1000 BK1005 LL100 2000 250 200 150 1000 100 50 0 1 BK1005 LL220 500 500 200 400 400 150 300 300 100 200 200 50 100 100 0 0 0 10 100 1000 10000 1 10 100 100 1000 0 10000 1 10 100 1000 10000 BK1005 LL470 BK1005 LL330 250 1 10 1000 BK1005 LL680 500 400 300 200 100 0 1 10000 10 100 1000 1 10000 10 100 1000 10000 BK1005 LM182 2500 2000 ／ FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS 400 R X 10 100 1000 Frequency［MHz］ 500 200 150 200 BK1005 HM121 250 1 1500 Z 1000 R 500 X 0 1 BKH1005 LM601 BK1005 LM102 2000 1500 800 Ｚ 600 1000 Ｒ 400 Z 500 R 200 0 1 10 100 Frequency [MHz] Ｘ 1000 10000 1 10 100 1500 R 1000 X 1000 10000 10000 2500 Z 2000 500 X 0 1000 3000 2500 1000 100 BKH1005 LM182 3000 Impedance[ ] Impedance ［Ω］ BKH1005 LM152 2500 1200 Impedance[ ] 1400 10 0 Z 2000 1500 R 1000 500 X 0 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 14 97 ■ ELECTRICAL CHARACTERISTICS ■ BK1608 ／ FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS BK1608 LL300 BK1608 LL470 500 500 250 250 0 0 1 BK1608 LL560 BK1608 LL680 500 1500 250 250 750 0 1 10 100 1000 10000 100 1000 10000 1 10 100 1000 10000 BK1608 LL121 500 0 10 0 1 10 100 1000 10000 1 10 100 1000 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 98 14 ■ ELECTRICAL CHARACTERISTICS 4000 2000 ／ FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS ■ BK2125 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 14 99 ■ ELECTRICAL CHARACTERISTICS 1000 Z 500 R X 0 1 10 100 1000 1000 Z R 500 ／ FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS 0 X 1 10 100 1000 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 100 14 Multilayer chip inductors Multilayer chip inductors for high frequency, Multilayer chip bead inductors Multilayer common mode choke coils（MC series F type） ■PACKAGING ①Minimum Quantity ●Tape & Reel Packaging Type CK1608（0603） CK2125（0805） CKS2125（0805） CKP1608（0603） CKP2012（0805） CKP2016（0806） CKP2520（1008） NM2012（0805） NM2520（1008） LK1005（0402） LK1608（0603） LK2125（0805） HK0402（01005） HK0603（0201） HK1005（0402） HK1608（0603） HK2125（0805） HKQ0402（01005） HKQ0603W（0201） HKQ0603C（0201） HKQ0603S（0201） HKQ0603U（0201） AQ105（0402） BK0402（01005） BK0603（0201） BK1005（0402） BKH0603（0201） BKH1005（0402） BK1608（0603） BK2125（0805） BK2010（0804） BK3216（1206） BKP0603（0201） BKP1005（0402） BKP1608（0603） BKP2125（0805） MCF0605(0202) MCF0806(0302) MCF1210(0504) MCF2010(0804) Thickness mm（inch） 0.8 （0.031） 0.85（0.033） 1.25（0.049） 0.85（0.033） 1.25（0.049） 0.8 （0.031） 0.9 （0.035） 0.9 （0.035） 0.7 （0.028） 0.9 （0.035） 1.1 （0.043） 0.9 （0.035） 0.9 （0.035） 1.1 （0.043） 0.5 （0.020） 0.8 （0.031） 0.85（0.033） 1.25（0.049） 0.2 （0.008） 0.3 （0.012） 0.5 （0.020） 0.8 （0.031） 0.85（0.033） 1.0 （0.039） 0.2 （0.008） 0.3 （0.012） 0.3 （0.012） 0.3 （0.012） 0.3 （0.012） 0.5 （0.020） 0.2 （0.008） 0.3 （0.012） 0.5 （0.020） 0.3 （0.012） 0.5 （0.020） 0.8 （0.031） 0.85（0.033） 1.25（0.049） 0.45（0.018） 0.8 （0.031） 0.3 （0.012） 0.5 （0.020） 0.8 （0.031） 0.85（0.033） 0.3 （0.012） 0.4 （0.016） 0.55（0.022） 0.45（0.018） Standard Quantity ［pcs］ Paper Tape Embossed Tape 4000 － 4000 － － 2000 4000 － － 2000 4000 － － 3000 － 3000 － 3000 － 3000 － 2000 － 3000 － 3000 － 2000 10000 － 4000 － 4000 － － 2000 20000 － 15000 － 10000 － 4000 － － 4000 － 3000 20000 40000 15000 － 15000 － 15000 － 15000 － 10000 － 20000 － 15000 － 10000 － 15000 － 10000 － 4000 － 4000 － － 2000 4000 － － 4000 15000 － 10000 － 4000 － 4000 － 15000 － － 10000 － 5000 － 4000 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_pack_e-E02R01 ②Taping material ●Card board carrier tape Top tape Base tape Sprocket hole Bottom tape Chip cavity CK CKP CK CKS LK LK LK HK HK HK HK HKQ HKQ AQ 1608 1608 2125 2125 1005 1608 2125 0402 0603 1005 1608 0402 0603 105 BK BK BK BK BK BK BKP BKP BKP BKP BKH BKH MCF 0402 0603 1005 1608 2125 2010 0603 1005 1608 2125 0603 1005 0605 CK CKS CKP CKP CKP NM NM LK HKQ HK 2125 2125 2012 2016 2520 2012 2520 2125 0402 2125 BK BK MCF MCF MCF 2125 3216 0806 1210 2010 Chip Filled Chip ●Embossed Tape Top tape Sprocket hole Base tape Chip cavity Chip Filled Chip ③Taping Dimensions ●Paper tape (8mm wide) ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_pack_e-E02R01 Type Thickness mm（inch） CK1608（0603） 0.8 （0.031） CK2125（0805） 0.85（0.033） CKS2125（0805） 0.85（0.033） CKP1608（0603） 0.8 （0.031） LK1005（0402） 0.5 （0.020） LK1608（0603） 0.8 （0.031） LK2125（0805） 0.85（0.033） HK0402（01005） 0.2 （0.008） HK0603（0201） 0.3 （0.012） HK1005（0402） 0.5 （0.020） HK1608（0603） 0.8 （0.031） HKQ0402（01005） 0.2 （0.008） HKQ0603W（0201） 0.3 （0.012） HKQ0603C（0201） 0.3 （0.012） HKQ0603S（0201） 0.3 （0.012） HKQ0603U（0201） 0.3 （0.012） AQ105（0402） 0.5 （0.020） BK0402（01005） 0.2 （0.008） BK0603（0201） 0.3 （0.012） BK1005（0402） 0.5 （0.020） BK1608（0603） 0.8 （0.031） BK2125（0805） 0.85（0.033） BK2010（0804） 0.45（0.018） BKP0603（0201） 0.3 （0.012） BKP1005（0402） 0.5 （0.020） BKP1608（0603） 0.8 （0.031） BKP2125（0805） 0.85（0.033） BKH0603（0201） 0.3 （0.012） BKH1005（0402） 0.5 （0.020） MCF0605(0202) 0.3 （0.012） Chip cavity Ａ Ｂ 1.0±0.2 1.8±0.2 （0.039±0.008） （0.071±0.008） 1.5±0.2 2.3±0.2 （0.059±0.008） （0.091±0.008） 1.5±0.2 2.3±0.2 （0.059±0.008） （0.091±0.008） 1.0±0.2 1.8±0.2 （0.039±0.008） （0.071±0.008） 0.65±0.1 1.15±0.1 （0.026±0.004） （0.045±0.004） 1.0±0.2 1.8±0.2 （0.039±0.008） （0.071±0.008） 1.5±0.2 2.3±0.2 （0.059±0.008） （0.091±0.008） 0.25±0.04 0.45±0.04 （0.010±0.002） （0.018±0.002） 0.40±0.06 0.70±0.06 （0.016±0.002） （0.028±0.002） 0.65±0.1 1.15±0.1 （0.026±0.004） （0.045±0.004） 1.0±0.2 1.8±0.2 （0.039±0.008） （0.071±0.008） 0.25±0.04 0.45±0.04 （0.010±0.002） （0.018±0.002） 0.40±0.06 0.70±0.06 （0.016±0.002） （0.028±0.002） 0.40±0.06 0.70±0.06 （0.016±0.002） （0.028±0.002） 0.40±0.06 0.70±0.06 （0.016±0.002） （0.028±0.002） 0.40±0.06 0.70±0.06 （0.016±0.002） （0.028±0.002） 0.75±0.1 1.15±0.1 （0.030±0.004） （0.045±0.004） 0.25±0.04 0.45±0.04 （0.010±0.002） （0.018±0.002） 0.40±0.06 0.70±0.06 （0.016±0.002） （0.028±0.002） 0.65±0.1 1.15±0.1 （0.026±0.004） （0.045±0.004） 1.0±0.2 1.8±0.2 （0.039±0.008） （0.071±0.008） 1.5±0.2 2.3±0.2 （0.059±0.008） （0.091±0.008） 1.2±0.1 2.17±0.1 （0.047±0.004） （0.085±0.004） 0.40±0.06 0.70±0.06 （0.016±0.002） （0.028±0.002） 0.65±0.1 1.15±0.1 （0.026±0.004） （0.045±0.004） 1.0±0.2 1.8±0.2 （0.039±0.008） （0.071±0.008） 1.5±0.2 2.3±0.2 （0.059±0.008） （0.091±0.008） 0.40±0.06 0.70±0.06 （0.016±0.002） （0.028±0.002） 0.65±0.1 1.15±0.1 （0.026±0.004） （0.045±0.004） 0.62±0.03 0.77±0.03 （0.024±0.001） （0.030±0.001） Insertion Pitch Ｆ 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 2.0±0.05 （0.079±0.002） 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 2.0±0.05 （0.079±0.002） 2.0±0.05 （0.079±0.002） 2.0±0.05 （0.079±0.002） 4.0±0.1 （0.157±0.004） 2.0±0.05 （0.079±0.002） 2.0±0.05 （0.079±0.002） 2.0±0.05 （0.079±0.002） 2.0±0.05 （0.079±0.002） 2.0±0.05 （0.079±0.002） 2.0±0.05 （0.079±0.002） 2.0±0.05 （0.079±0.002） 2.0±0.05 （0.079±0.002） 2.0±0.05 （0.079±0.002） 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 2.0±0.05 （0.079±0.002） 2.0±0.05 （0.079±0.002） 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 2.0±0.05 （0.079±0.002） 2.0±0.05 （0.079±0.002） 2.0±0.05 （0.079±0.002） Tape Thickness Ｔ 1.1max （0.043max） 1.1max （0.043max） 1.1max （0.043max） 1.1max （0.043max） 0.8max （0.031max） 1.1max （0.043max） 1.1max （0.043max） 0.36max （0.014max） 0.45max （0.018max） 0.8max （0.031max） 1.1max （0.043max） 0.36max （0.014max） 0.45max （0.018max） 0.45max （0.018max） 0.45max （0.018max） 0.45max （0.018max） 0.8max （0.031max） 0.36max （0.014max） 0.45max （0.018max） 0.8max （0.031max） 1.1max （0.043max） 1.1max （0.043max） 0.8max （0.031max） 0.45max （0.018max） 0.8max （0.031max） 1.1max （0.043max） 1.1max （0.043max） 0.45max （0.018max） 0.8max （0.031max） 0.45max （0.018max） Unit : mm（inch） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_pack_e-E02R01 ●Embossed Tape (8mm wide) Type Thickness mm（inch） CK2125（0805） 1.25（0.049） CKS2125（0805） 1.25（0.049） CKP2012（0805） 0.9 （0.035） CKP2016（0806） 0.9 （0.035） Chip cavity Ａ Ｂ 1.5±0.2 2.3±0.2 （0.059±0.008） （0.091±0.008） 1.5±0.2 2.3±0.2 （0.059±0.008） （0.091±0.008） 1.55±0.2 2.3±0.2 （0.061±0.008） （0.091±0.008） 1.8±0.1 2.2±0.1 （0.071±0.004） （0.087±0.004） Insertion Pitch Ｆ 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 2.3±0.1 （0.091±0.004） 2.8±0.1 （0.110±0.004） 4.0±0.1 （0.157±0.004） 1.55±0.2 （0.061±0.008） 2.3±0.2 （0.091±0.008） 4.0±0.1 （0.157±0.004） 2.3±0.1 （0.091±0.004） 2.8±0.1 （0.110±0.004） 4.0±0.1 （0.157±0.004） 1.5±0.2 （0.059±0.008） 2.3±0.2 （0.091±0.008） 4.0±0.1 （0.157±0.004） 1.5±0.2 （0.059±0.008） 2.3±0.2 （0.091±0.008） 4.0±0.1 （0.157±0.004） 1.5±0.2 （0.059±0.008） 1.9±0.1 （0.075±0.004） 0.75±0.05 （0.030±0.002） 1.15±0.05 （0.045±0.002） 1.1±0.1 （0.043±0.004） 2.3±0.2 （0.091±0.008） 3.5±0.1 （0.138±0.004） 0.95±0.05 （0.037±0.002） 1.40±0.05 （0.055±0.002） 2.3±0.1 （0.091±0.004） 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 2.0±0.05 （0.079±0.002） 4.0±0.1 （0.157±0.004） 4.0±0.1 （0.157±0.004） 0.7 （0.028） CKP2520（1008） 0.9 （0.035） 1.1 （0.043） NM2012（0805） 0.9 （0.035） 0.9 （0.035） NM2520（1008） 1.1 （0.043） LK2125（0805） 1.25（0.049） 0.85（0.033） HK2125（0805） 1.0 （0.039） BK2125（0805） 1.25（0.049） BK3216（1206） 0.8（0.031） MCF0806(0302) 0.4 （0.016） MCF1210(0504) 0.55（0.022） MCF2010(0804) 0.45（0.018） Tape Thickness K T 2.0 0.3 （0.079） （0.012） 2.0 0.3 （0.079） （0.012） 1.3 0.3 （0.051） （0.012） 1.3 0.25 （0.051） （0.01） 1.4 （0.055） 1.4 0.3 （0.055） （0.012） 1.7 （0.067） 1.3 0.3 （0.051） （0.012） 1.4 （0.055） 0.3 （0.012） 1.7 （0.067） 2.0 0.3 （0.079） （0.012） 1.5 （0.059） 0.3 （0.012） 2.0 （0.079） 2.0 0.3 （0.079） （0.012） 1.4 0.3 （0.055） （0.012） 0.55 0.3 （0.022） （0.012） 0.65 0.3 （0.026） （0.012） 0.85 0.3 （0.033） （0.012） Unit : mm（inch） ●Embossed Tape (4mm wide) Type HKQ0402(01005) Thickness mm（inch） 0.2 （0.008） Chip cavity Ａ 0.23 Ｂ 0.43 Insertion Pitch Ｆ 1.0±0.02 Tape Thickness K T 0.5max. 0.25max. Unit : mm ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_pack_e-E02R01 ④LEADER AND BLANK PORTION Blank portion Chip cavity Blank portion Leader 100mm or more (3.94inches or more) 160mm or more (6.3inches or more) Direction of tape feed 400mm or more (15.7inches or more) ⑤Reel Size t E C R B D A W A φ178±2.0 B φ50 or more C φ13.0±0.2 4mm width tape 8mm width tape t 1.5max. 2.5max. W 5±1.0 10±1.5 D φ21.0±0.8 E 2.0±0.5 R 1.0 (Unit : mm) ⑥Top tape strength The top tape requires a peel-off force of 0.1～0.7N in the direction of the arrow as illustrated below. Pull direction 0～15° Top tape Base tape ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_pack_e-E02R01 Multilayer chip inductors Multilayer chip inductors for high frequency, Multilayer chip bead inductors Multilayer common mode choke coils（MC series F type） ■RELIABILITY DATA 1. Operating Temperature Range BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value －55～＋125℃ BK2010 BK3216 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0402/HKQ0402 HK0603 HK1005 HK1608 HK2125 HKQ0603W/HKQ0603C/HKQ0603S/ HKQ0603U/ AQ105 －55～＋85℃ －40～＋85℃ －40～＋85℃ －55～＋125℃ －40～＋85℃ －55～＋125℃ ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 2. Storage Temperature Range BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value －55～＋125℃ BK2010 BK3216 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0402/HKQ0402 HK0603 HK1005 HK1608 HK2125 HKQ0603W/HKQ0603C/HKQ0603S/ HKQ0603U/ AQ105 －55～＋85℃ －40～＋85℃ －40～＋85℃ －55～＋125℃ －40～＋85℃ －55～＋125℃ ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 3. Rated Current BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY BK2010 BK3216 150～750mA DC 100～500mA DC 120～1000mA DC 115～160mA DC 200～300mA DC 150～1500mA DC 200～1200mA DC 100mA DC 100～200mA DC 0.8～1.8A DC 0.8～2.4A DC 1.0～3.0A DC 1.5～4.0A DC 0.05A DC 0.1～0.13A DC 0.1A DC 0.1A DC 50～60mA DC 60～500mA DC 110～280mA DC 0.35～0.9A DC 0.7～1.2A DC 0.9～1.6A DC 1.1～1.8A DC 1.0～1.2A DC 0.9～1.2A DC 20～25mA DC 1～150mA DC 5～300mA DC 160～380mA DC 60～470mA DC 110～300mA DC (-55～+125℃） 200～900mA DC (-55～+85℃) 150～300mA DC 300mA DC 90～500mA DC 100～850mA DC 160～850mA DC 130～600mA DC 190～900mA DC 280～710mA DC BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 Specified Value CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0402 HK0603 HK1005 HK1608 HK2125 HKQ0402 HKQ0603W HKQ0603C HKQ0603S HKQ0603U AQ105 Definition of rated current： ・In the CK, CKS and BK Series, the rated current is the value of current at which the temperature of the element is increased within 20℃. ・In the BK Series P type and CK Series P type, NM Series the rated current is the value of current at which the temperature of the element is increased within 40℃. ・In the LK, HK, HKQ, and AQ Series, the rated current is either the DC value at which the internal L value is decreased within 5% with the application of DC bias, or the value of current at which the temperature of the element is increased within 20℃. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 4. Impedance BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value Test Methods and Remarks BK2010 BK3216 10～180Ω ±5Ω(10Ω), ±25%(Other) 10～600Ω ±25% 10～1800Ω ±25% 600～1500Ω ±25% 600～1800Ω ±25% 22～2500Ω ±25% 15～2500Ω ±25% 5～1000Ω ±25% 60～1000Ω ±25% 10～120Ω ±5Ω(10Ω), ±25%(Other) 10～330Ω ±5Ω(EM100), ±25%(Other) 33～470Ω ±25% 33～330Ω ±25% 12～90Ω ±5Ω(12Ω), ±20%(35Ω), ±25%(Other) 12～90Ω ±5Ω(12Ω), ±20%(Other) 40～90Ω ±25% 90Ω ±25% BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 － LK1608 LK2125 HK0402/HKQ0402 HK0603 HK1005 HK1608 HK2125 HKQ0603W/HKQ0603C/HKQ0603S/ HKQ0603U AQ105 BK0402Series Measuring frequency : 100±1MHz Measuring equipment : E4991A（or its equivalent） Measuring jig : 16197A（or its equivalent） BK0603Series, BKP0603Series Measuring frequency : 100±1MHz Measuring equipment : 4291A（or its equivalent） Measuring jig : 16193A（or its equivalent） BK1005Series, BKP1005Series ,BKH1005Series Measuring frequency : 100±1MHz Measuring equipment : 4291A（or its equivalent） Measuring jig : 16192A（or its equivalent）, 16193A（or its equivalent） BK1608・2125Series, BKP1608・2125Series Measuring frequency : 100±1MHz Measuring equipment : 4291A（or its equivalent）, 4195A（or its equivalent） Measuring jig : 16092A（or its equivalent） or 16192A（or its equivalent）/HW BK2010・3216Series, MCFSeries Measuring frequency : 100±1MHz Measuring equipment : 4291A（or its equivalent）, 4195A（or its equivalent） Measuring jig : 16192A（or its equivalent） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 5. Inductance BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value BK2010 BK3216 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0402 HK0603 HK1005 HK1608 HK2125 HKQ0402 HKQ0603W HKQ0603C HKQ0603S HKQ0603U AQ105 CK、LK、CKP、NM Series Measuring frequency Measuring frequency Measuring frequency Measuring frequency Measuring frequency Measuring frequency Measuring frequency Measuring equipment /jig Test Methods and Remarks Measuring current HK、HKQ、AQ Series Measuring frequency Measuring frequency Measuring frequency Measuring frequency Measuring frequency Measuring equipment /jig － 4.7～10.0μH： ±20% 0.1～10.0μH： ±20% 1.0～10.0μH： ±20% 0.33～2.2μH： ±20% 0.47～4.7μH： ±20% 0.47～4.7μH： ±20% 0.47～4.7μH： ±20% 0.82～1.0μH： ±20% 1.0～2.2μH： ±20% 0.12～2.2μH： ±10 or 20% 0.047～33.0μH： ±20% 0.10～12.0μH： ±10% 0.047～33.0μH： ±20% 0.10～12.0μH： ±10% 1.0～5.6nH： ±0.3nH 6.8～12nH： ±5% 1.0～6.2nH： ±0.3nH 6.8～100nH： ±5% 1.0～6.2nH： ±0.3nH 6.8～270nH： ±5% 1.0～5.6nH： ±0.3nH 6.8～470nH： ±5% 1.5～5.6nH： ±0.3nH 6.8～470nH： ±5% 0.5～3.9nH： ±0.1 or 0.2 or 0.3nH 4.3～5.6nH： ±0.3nH or 3% 6.2～27nH： ±3 or 5% 0.6～3.9nH： ±0.1 or 0.2 or 0.3nH 4.3～6.2nH： ±0.2 or 0.3nH or 3 or 5% 6.8～100nH： ±3 or 5% 0.6～3.9nH： ±0.1 or 0.2 or 0.3nH 4.3～6.2nH： ±0.2 or 0.3nH 6.8～22nH： ±3 or 5% 0.6～6.2nH： ±0.2 or 0.3nH 6.8～22nH： ±3 or 5% 0.6～4.2nH： ±0.1 or 0.2 or 0.3nH 4.3～6.5nH： ±0.2 or 0.3nH 6.8～22nH： ±3 or 5% 1.0～6.2nH： ±0.3nH 6.8～15nH： ±5% : 2～4MHz（CK1608） : 2～25MHz（CK2125） : 2～10MHz（CKS2125） : 10～25MHz（LK1005） : 1～50MHz（LK1608） : 0.4～50MHz（LK2125） : 1MHz（CKP1608・CKP2012・CKP2016・CKP2520・NM2012・NM2520） :・4194A＋16085B＋16092A（or its equivalent） ・4195A＋41951＋16092A（or its equivalent） ・4294A＋16192A（or its equivalent） ・4291A＋16193A（or its equivalent）/LK1005 ・4285A＋42841A＋42842C＋42851－61100（CKP1608･CKP2012・CKP2016・CKP2520・NM2012・NM2520） :・1mA rms（0.047～4.7μH） ・0.1mA rms（5.6～33μH） : 100MHz（HK0402・HK0603・HK1005・AQ105） : 50/100MHz（HK1608・HK2125） : 500MHz（HKQ0603C･HKQ0603S・HKQ0603U） : 300/500MHz（HKQ0603W） : 100/500MHz（HKQ0402） :・4291A＋16197A（or its equivalent）/HK0603・AQ105 ・4291A＋16193A（or its equivalent）/HK1005 ・E4991A＋16197A（or its equivalent）/HKQ0603S・HKQ0603U・HKQ0603W・HKQ0603C ・4291A＋16092A ＋ in-house made jig（or its equivalent）/HK1608・HK2125 ・E4991A＋16196D（or its equivalent）/HK0402・HKQ0402 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 6. Q BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY BK2010 BK3216 － BKP0603 BKP1005 BKP1608 BKP2125 Specified Value MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0402 HK0603 HK1005 HK1608 HK2125 HKQ0402 HKQ0603W HKQ0603C HKQ0603S HKQ0603U AQ105 LKSeries Measuring Measuring Measuring Measuring － 10～20 min. 10～35 min. 15～50 min. 3 min. 4～5 min. 8 min. 8～12 min. 10～18 min. 3～8 min. 6～15 min. 14～15 min. 10～13 min. 14 min. 8 min. frequency frequency frequency equipment /jig Measuring current Test Methods and Remarks HK、HKQ、AQ Series Measuring frequency Measuring frequency Measuring frequency Measuring frequency Measuring frequency Measuring equipment /jig : 10～25MHz（LK1005） : 1～50MHz（LK1608） : 0.4～50MHz（LK2125） :・4194A＋16085B＋16092A（or its equivalent） ・4195A＋41951＋16092A（or its equivalent） ・4294A＋16192A（or its equivalent） ・4291A＋16193A（or its equivalent）/LK1005 ・1mA rms（0.047～4.7μH） ・0.1mA rms（5.6～33μH） : 100MHz（HK0402・HK0603・HK1005・AQ105） : 50/100MHz（HK1608・HK2125） : 500MHz（HKQ0603C･HKQ0603S・HKQ0603U） : 300/500MHz（HKQ0603W） : 100/500MHz（HKQ0402） :・4291A＋16197A（or its equivalent）/HK0603・AQ105 ・4291A＋16193A（or its equivalent）/HK1005 ・E4991A＋16197A（or its equivalent）/HKQ0603S・HKQ0603U・HKQ0603W・HKQ0603C ・4291A＋16092A ＋ in-house made jig（or its equivalent）/HK1608, HK2125 ・E4991A＋16196D（or its equivalent）HK0402・HKQ0402 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 7. DC Resistance BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value Test Methods and Remarks BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0402 HK0603 HK1005 HK1608 HK2125 HKQ0402 HKQ0603W HKQ0603C BK2010 BK3216 0.07～0.75Ω max. 0.065～1.50Ω max. 0.03～0.90Ω max. 1.50～3.20Ω max. 0.85～2.00Ω max. 0.05～1.10Ω max. 0.05～0.75Ω max. 0.10～0.90Ω max. 0.15～0.80Ω max. 0.030～0.180Ω max. 0.0273～0.220Ω max. 0.025～0.18Ω max. 0.020～0.075Ω max. 2.5～6.5Ω max 2.5～6.5Ω max. 2.5～4.5Ω max. 4.5Ω max. 0.45～0.85Ω（±30%） 0.16～0.65Ω max. 0.12～0.52Ω max. 0.15～0.35Ω max. 0.08～0.28Ω max. 0.075～0.20Ω max 0.05～0.16Ω max. 0.10～0.15Ω max. 0.11～0.22Ω max. 0.41～1.16Ω max. 0.2～2.2Ω max. 0.1～1.1Ω max. 0.18～0.99Ω max. 0.11～3.74Ω max. 0.08～4.8Ω max. 0.05～2.6Ω max. 0.10～1.5Ω max. 0.08～2.24Ω max. 0.07～4.1Ω max. 0.07～1.6Ω max. HKQ0603S 0.06～1.29Ω max. HKQ0603U AQ105 0.06～1.29Ω max. 0.07～0.45Ω max. Measuring equipment：VOAC-7412, VOAC-7512, VOAC-7521（made by Iwasaki Tsushinki） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 8. Self Resonance Frequency（SRF） BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY BK2010 BK3216 － BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 Specified Value Test Methods and Remarks MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0402 HK0603 HK1005 HK1608 HK2125 17～25MHz min. 24～235MHz min. 24～75MHz min. － 40～180MHz min. 9～260MHz min. 13～320MHz min. 2900～10000MHz min. 900～10000MHz min. 400～10000MHz min. 300～10000MHz min. 200～4000MHz min. HKQ0402 1700～10000MHz min. HKQ0603W HKQ0603C HKQ0603S HKQ0603U AQ105 LK、CK Series : Measuring equipment Measuring jig HK、HKQ、AQ Series : Measuring equipment 800～10000MHz min. 2500～10000MHz min. 1900～10000MHz min. 1900～10000MHz min. 2300～10000MHz min. : 4195A（or its equivalent） : 41951＋16092A（or its equivalent） : 8719C（or its equivalent）・8753D（or its equivalent）/HK2125 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 9. Temperature Characteristic BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value Test Methods and Remarks BK2010 BK3216 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0402 HK0603 HK1005 HK1608 HK2125 HKQ0402 HKQ0603W HKQ0603C HKQ0603S HKQ0603U AQ105 HK、HKQ、AQ Series： Temperature range Reference temperature － Inductance change：Within ±10％ : －30～＋85℃ : ＋20℃ ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 10. Resistance to Flexure of Substrate BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 BK2010 ARRAY BK3216 BKP0603 BKP1005 BKP1608 BKP2125 Specified Value MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0402 HK0603 HK1005 HK1608 HK2125 HKQ0402 HKQ0603W HKQ0603C HKQ0603S HKQ0603U AQ105 Warp Testing board Thickness Test Methods and Remarks No mechanical damage. : 2mm（BK Series without 0402size、BKP、BKH1005、CK、CKS、CKP、NM、LK、HK、HKQ0603S、HKQ0603U、 AQ Series、MCF1210） : 1mm（BK0402、BKH0603、HK0402、HKQ0402、HKQ0603W、HKQ0603C Series、MCF Series without 1210 size,） : glass epoxy-resin substrate : 0.8mm 20 R-230 Board Warp Deviation±1 45 45 （Unit：mm） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 11. Solderability BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value Test Methods and Remarks BK2010 BK3216 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0402 HK0603 HK1005 HK1608 HK2125 HKQ0402 HKQ0603W HKQ0603C HKQ0603S HKQ0603U AQ105 Solder temperature Solder temperature Duration At least 75％ of terminal electrode is covered by new solder. At least 75％ of terminal electrode is covered by new solder. ：230±5℃ (JIS Z 3282 H60A or H63A) ：245±3℃ (Sn/3.0Ag/0.5Cu) ：4±1 sec. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 12. Resistance to Soldering BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value BK2010 BK3216 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 Test Methods and Remarks HK0402 HK0603 HK1005 HK1608 HK2125 HKQ0402 HKQ0603W HKQ0603C HKQ0603S HKQ0603U AQ105 Solder temperature Duration Preheating temperature Preheating time Flux Recovery Appearance：No significant abnormality Impedance change：Within ±30％ Appearance：No significant abnormality Impedance change：Within ±20％ No mechanical damage. Remaining terminal electrode：70％ min Inductance change R10～4R7： Within ±10％ 6R8～100： Within ±15％ CKS2125 ： Within ±20％ CKP1608、CKP2012、CKP2016、CKP2520、NM2012、NM2520： Within ±30％ No mechanical damage. Remaining terminal electrode：70％ min. Inductance change： Within ±15％ No mechanical damage. Remaining terminal electrode：70％ min. Inductance change 47N～4R7： Within ±10％ 5R6～330： Within ±15％ No mechanical damage. Remaining terminal electrode：70％ min. Inductance change： Within ±5％ ：260±5℃ ：10±0.5 sec. ：150 to 180℃ ：3 min. ：Immersion into methanol solution with colophony for 3 to 5 sec. ：2 to 3 hrs of recovery under the standard condition after the test.（See Note 1） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 13. Thermal Shock BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY BK2010 BK3216 Appearance：No significant abnormality Impedance change： Within ±30％ BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 Appearance：No significant abnormality Impedance change： Within ±20％ MCF 1210 MCF 2010 CK1608 No mechanical damage. CK2125 Inductance change：Within ±20％ Q change：Within ±30％ Inductance change：Within ±20％ （CKS2125） CKS2125 Specified Value CKP1608 CKP2012 CKP2016 No mechanical damage. Inductance change： Within ±30％ CKP2520 NM2012 NM2520 LK1005 No mechanical damage. LK1608 Inductance change： Within ±10％ Q change： Within ±30％ LK2125 HK0402 HK0603 HK1005 HK1608 HK2125 No mechanical damage. HKQ0402 Inductance change： Within ±10％ Q change： Within ±20％ HKQ0603W HKQ0603C HKQ0603S HKQ0603U AQ105 Conditions for 1 cycle Step temperature（℃） time（min.） 1 Minimum operating temperature ＋0/－3 30±3 Test Methods and 2 Room temperature 2～3 Remarks 3 Maximum operating temperature ＋3/－0 30±3 4 Room temperature 2～3 Number of cycles：5 Recovery：2 to 3 hrs of recovery under the standard condition after the test.（See Note 1） (Note 1) When there are questions concerning measurement result；measurement shall be made after 48±2 hrs of recovery under the standard condition. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 14. Damp Heat（ Steady state） BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0402 HK0603 HK1005 HK1608 HK2125 HKQ0402 HKQ0603W HKQ0603C HKQ0603S HKQ0603U AQ105 BK、BKP、BKH Temperature Humidity Duration Recovery Test Methods and Remarks BK2010 BK3216 Appearance：No significant abnormality Impedance change： Within ±30％ Appearance：No significant abnormality Impedance change： Within ±20％ No mechanical damage. Inductance change： Within ±20％ Q change： Within ±30％ Inductance change： Within ±20％ No mechanical damage. Inductance change： Within ±30％ No mechanical damage. Inductance change： Within ±10％ Q change： Within ±30％ No mechanical damage. Inductance change： Within ±20％ Q change： Within ±30％ No mechanical damage. Inductance change： Within ±10％ Q change： Within ±20％ Series、MCF Series： ：40±2℃ ：90 to 95％RH ：500＋24/－0 hrs ：2 to 3 hrs of recovery under the standard condition after the removal from test chamber.（See Note 1） LK、CK、CKS、CKP、NM、HK、HKQ、AQ Series： Temperature ：40±2℃（ LK、CK、CKS、CKP、NM Series） ：60±2℃（ HK、HKQ、AQ Series） Humidity ：90 to 95％RH Duration ：500±12 hrs Recovery ：2 to 3 hrs of recovery under the standard condition after the removal from test chamber.（See Note 1） ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 15. Loading under Damp Heat BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY BKP0603 BKP1005 BKP1608 BKP2125 CK1608 CK2125 CKS2125 Specified Value CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 BK2010 BK3216 Appearance：No significant abnormality Impedance change： Within ±30％ No mechanical damage. Inductance change： Within ±20％ Q change： Within ±30％ No mechanical damage. Inductance change： Within ±20％ No mechanical damage. Inductance change： Within ±30％ No mechanical damage. Inductance change： Within ±10％ Q change： Within ±30％ No mechanical damage. Inductance change： 0.047～12.0μH： Within ±10％ 15.0～33.0μH： Within ±15％ Q change： Within ±30％ No mechanical damage. Inductance change： Within ±20％ Q change： Within ±30％ HK0402 HK0603 HK1005 HK1608 HK2125 No mechanical damage. HKQ0402 Inductance change： Within ±10％ Q change： Within ±20％ HKQ0603W HKQ0603C HKQ0603S HKQ0603U AQ105 BK、BKP、BKH Series： Temperature ：40±2℃ Humidity ：90 to 95％RH Applied current ：Rated current Duration ：500＋24/－0 hrs Recovery ：2 to 3 hrs of recovery under the standard condition after the removal from test chamber.（See Note 1） Test Methods and LK、CK、CKS、CKP、NK、HK、HKQ、AQ Series： Remarks Temperature ：40±2℃（ LK、CK、CKS、CKP、NM Series） ：60±2℃（ HK、HKQ、AQ Series） Humidity ：90 to 95％RH Applied current ：Rated current Duration ：500±12 hrs Recovery ：2 to 3 hrs of recovery under the standard condition after the removal from test chamber.（See Note 1） Note on standard condition: "standard condition" referred to herein is defined as follows: 5 to 35℃ of temperature, 45 to 85% relative humidity, and 86 to 106kPa of air pressure. When there are questions concerning measurement results: In order to provide correlation data, the test shall be conducted under condition of 20±2℃ of temperature, 60 to 70% relative humidity, and 86 to 106kPa of air pressure. Unless otherwise specified, all the tests are conducted under the "standard condition." (Note 1) Measurement shall be made after 48±2 hrs of recovery under the standard condition. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 16. Loading at High Temperature BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 Specified Value CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 BK2010 BK3216 Appearance：No significant abnormality Impedance change： Within ±30％ Appearance：No significant abnormality Impedance change： Within ±20％ No mechanical damage. Inductance change： Within ±20％ Q change： Within ±30％ No mechanical damage. Inductance change： Within ±20％ No mechanical damage. Inductance change： Within ±30％ No mechanical damage. Inductance change： Within ±10％ Q change： Within ±30％ No mechanical damage. Inductance change： 0.047～12.0μH： Within ±10％ 15.0～33.0μH： Within ±15％ Q change： Within ±30％ No mechanical damage. Inductance change： Within ±20％ Q change： Within ±30％ HK0402 HK0603 HK1005 HK1608 HK2125 No mechanical damage. HKQ0402 Inductance change： Within ±10％ Q change： Within ±20％ HKQ0603W HKQ0603C HKQ0603S HKQ0603U AQ105 BK、BKH、BKP Series、MCF Series： Temperature : 125±3℃（BK、BKH Series） : 85±3℃（BKP、MCF Series） Applied current ：Rated current Duration ：500＋24/－0 hrs Recovery ：2 to 3 hrs of recovery under the standard condition after the removal from test chamber. （See Note 1） Test Methods and Remarks LK、CK、CKS、CKP、NM、HK、HKQ、AQ Series： Temperature : 85±2℃（LK、CK、CKS、CKP、NM Series） : 85±2℃（HK1608，2125） : 85±2℃（HK1005, AQ105 operating temperature range－55～＋85℃） : 125±2℃（HK0402, HKQ0402, HK0603, HK1005, HKQ0603S, HKQ0603U, HKQ0603W, HKQ0603C, AQ105 operating temperature range－55～＋125℃） Applied current ：Rated current Duration ：500±12 hrs Recovery ：2 to 3 hrs of recovery under the standard condition after the test.（See Note 1） Note on standard condition: "standard condition" referred to herein is defined as follows: 5 to 35℃ of temperature, 45 to 85% relative humidity, and 86 to 106kPa of air pressure. When there are questions concerning measurement results: In order to provide correlation data, the test shall be conducted under condition of 20±2℃ of temperature, 60 to 70% relative humidity, and 86 to 106kPa of air pressure. Unless otherwise specified, all the tests are conducted under the "standard condition." (Note 1) Measurement shall be made after 48±2 hrs of recovery under the standard condition. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 Precautions on the use of Multilayer chip inductors Multilayer chip inductors for high frequency, Multilayer chip bead inductors Multilayer common mode choke coils（MC series F type） ■PRECAUTIONS 1. Circuit Design Precautions ◆Verification of operating environment, electrical rating and performance 1. A malfunction in medical equipment, spacecraft, nuclear reactors, etc. may cause serious harm to human life or have severe social ramifications. As such, any inductors to be used in such equipment may require higher safety and/or reliability considerations and should be clearly differentiated from components used in general purpose applications. ◆Operating Current（Verification of Rated current） 1. The operating current for inductors must always be lower than their rated values. 2. Do not apply current in excess of the rated value because the inductance may be reduced due to the magnetic saturation effect. 2. PCB Design Precautions ◆Pattern configurations（Design of Land-patterns） 1. When inductors are mounted on a PCB, the size of land patterns and the amount of solder used（size of fillet）can directly affect inductor performance. Therefore, the following items must be carefully considered in the design of solder land patterns: （1） The amount of solder applied can affect the ability of chips to withstand mechanical stresses which may lead to breaking or cracking. Therefore, when designing land-patterns it is necessary to consider the appropriate size and configuration of the solder pads which in turn determines the amount of solder necessary to form the fillets. （2） When more than one part is jointly soldered onto the same land or pad, the pad must be designed so that each component's soldering point is separated by solder-resist. （3） The larger size of land patterns and amount of solder, the smaller Q value after mounting on PCB. It makes higher the Q value to design land patterns smaller than terminal electrode of chips. ◆Pattern configurations（Inductor layout on panelized［ breakaway］ PC boards） 1. After inductors have been mounted on the boards, chips can be subjected to mechanical stresses in subsequent manufacturing processes （PCB cutting, board inspection, mounting of additional parts, assembly into the chassis, wave soldering the reflow soldered boards etc.）For this reason, planning pattern configurations and the position of SMD inductors should be carefully performed to minimize stress. ◆Pattern configurations（Design of Land-patterns） 1. The following diagrams and tables show some examples of recommended patterns to prevent excessive solder amounts（larger fillets which extend above the component end terminations）. Examples of improper pattern designs are also shown. （1） Recommended land dimensions for a typical chip inductor land patterns for PCBs Land pattern Solder-resist Chip inductor Chip inductor W C B Technical considerations A B L Recommended land dimensions for wave-soldering Type 1608 2012 2125 L 1.6 2.0 2.0 Size W 0.8 1.25 1.25 A 0.8～1.0 1.0～1.4 1.0～1.4 B 0.5～0.8 0.8～1.5 0.8～1.5 C 0.6～0.8 0.9～1.2 0.9～1.2 Recommended land dimensions for reflow-soldering Type 0402 0603 1005 L 0.4 0.6 1.0 Size W 0.2 0.3 0.5 A 0.15～0.25 0.20～0.30 0.45～0.55 B 0.10～0.20 0.20～0.30 0.40～0.50 C 0.15～0.30 0.25～0.40 0.45～0.55 Type L Size W A B C 2125 2.0 1.25 0.8～1.2 0.8～1.2 0.9～1.6 2016 2.0 1.6 0.8～1.2 0.8～1.2 1.2～2.0 2520 2.5 2.0 1.0～1.4 0.6～1.0 1.8～2.2 （Unit：mm） 2016 2520 2.0 2.5 1.6 2.0 1.0～1.4 1.0～1.4 0.8～1.5 0.6～1.0 1.3～1.6 1.6～2.0 （Unit：mm） 105 1.0 0.6 0.50～0.55 0.30～0.40 0.60～0.70 1608 1.6 0.8 0.8～1.0 0.6～0.8 0.6～0.8 3216 3.2 1.6 1.8～2.5 0.8～1.7 1.2～1.6 2012 2.0 1.25 0.8～1.2 0.8～1.2 0.9～1.6 3216 3.2 1.6 1.8～2.5 0.6～1.5 1.2～2.0 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_prec_e-E02R01 b b a a a a Excess solder can affect the ability of chips to withstand mechanical stresses. Therefore, please take proper precautions when designing land-patterns. Recommended land dimension for Reflow-soldering d c c Type 3216 2010 1210 0806 0605 L 3.2 2.0 1.25 0.85 0.65 Size W 1.6 1.0 1.0 0.65 0.50 a 0.7～0.9 0.5～0.6 0.45～0.55 0.25～0.35 0.27～0.33 b 0.8～1.0 c 0.4～0.5 d 0.8 （Unit：mm） d （（2） Examples of good and bad solder application Item 0.5～0.6 0.2～0.3 0.5 0.7～0.8 0.25～0.35 0.17～0.23 0.25～0.35 0.25～0.35 0.20～0.26 0.55 0.5 0.4 Not recommended Recommended Lead wire of component Solder-resist Mixed mounting of SMD and leaded components Chassis Solder (for grounding) Solder-resist Component placement close to the chassis Electrode pattern Lead wire of component Soldering iron Hand-soldering of leaded components near mounted components Solder-resist Solder-resist Horizontal component placement ◆Pattern configurations（Inductor layout on panelized［ breakaway］ PC boards） 1-1. The following are examples of good and bad inductor layout; SMD inductors should be located to minimize any possible mechanical stresses from board warp or deflection. Item Not recommended Recommended Position the component at a right angle to the direction of the mechanical stresses that are anticipated. Deflection of the board 1-2. To layout the inductors for the breakaway PC board, it should be noted that the amount of mechanical stresses given will vary depending on inductor layout. An example below should be counted for better design. E D Perforation C A B Slit Magnitude of stress A＞B＝C＞D＞E 1-3. When breaking PC boards along their perforations, the amount of mechanical stress on the inductors can vary according to the method used. The following methods are listed in order from least stressful to most stressful: push-back, slit, V-grooving, and perforation. Thus, any ideal SMD inductor layout must also consider the PCB splitting procedure. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_prec_e-E02R01 3. Considerations for automatic placement Precautions ◆Adjustment of mounting machine 1. Excessive impact load should not be imposed on the inductors when mounting onto the PC boards. 2. The maintenance and inspection of the mounter should be conducted periodically. ◆Selection of Adhesives 1. Mounting inductors with adhesives in preliminary assembly, before the soldering stage, may lead to degraded inductor characteristics unless the following factors are appropriately checked; the size of land patterns, type of adhesive, amount applied, hardening temperature and hardening period. Therefore, it is imperative to consult the manufacturer of the adhesives on proper usage and amounts of adhesive to use. ◆Adjustment of mounting machine 1. If the lower limit of the pick-up nozzle is low, too much force may be imposed on the inductors, causing damage. To avoid this, the following points should be considered before lowering the pick-up nozzle: （1） The lower limit of the pick-up nozzle should be adjusted to the surface level of the PC board after correcting for deflection of the board. （2） The pick-up pressure should be adjusted between 1 and 3N static loads. （3） To reduce the amount of deflection of the board caused by impact of the pick-up nozzle, supporting pins or back-up pins should be used under the PC board. The following diagrams show some typical examples of good pick-up nozzle placement: Item Improper method Proper method Single-sided mounting chipping or cracking supporting pins or back-up pins Double-sided mounting chipping or cracking Technical considerations supporting pins or back-up pins 2. As the alignment pin wears out, adjustment of the nozzle height can cause chipping or cracking of the inductors because of mechanical impact on the inductors. To avoid this, the monitoring of the width between the alignment pin in the stopped position, and maintenance, inspection and replacement of the pin should be conducted periodically. ◆Selection of Adhesives 1. Some adhesives may cause reduced insulation resistance. The difference between the shrinkage percentage of the adhesive and that of the inductors may result in stresses on the inductors and lead to cracking. Moreover, too little or too much adhesive applied to the board may adversely affect component placement, so the following precautions should be noted in the application of adhesives. （1） Required adhesive characteristics a. The adhesive should be strong enough to hold parts on the board during the mounting & solder process. b. The adhesive should have sufficient strength at high temperatures. c. The adhesive should have good coating and thickness consistency. d. The adhesive should be used during its prescribed shelf life. e. The adhesive should harden rapidly. f. The adhesive must not be contaminated. g. The adhesive should have excellent insulation characteristics. h. The adhesive should not be toxic and have no emission of toxic gasses. （2） When using adhesives to mount inductors on a PCB, inappropriate amounts of adhesive on the board may adversely affect component placement. Too little adhesive may cause the inductors to fall off the board during the solder process. Too much adhesive may cause defective soldering due excessive flow of adhesive on to the land or solder pad. Amount of adhesives After inductors are bonded ［Recommended conditions］ a a Figure 0805 case sizes as examples a 0.3mm min b b 100～120μm c Area with no adhesive c c 4. Soldering Precautions ◆Selection of Flux 1. Since flux may have a significant effect on the performance of inductors, it is necessary to verify the following conditions prior to use; （1） Flux used should be with less than or equal to 0.1 wt% （Chlorine conversion method） of halogenated content. Flux having a strong acidity content should not be applied. （2） When soldering inductors on the board, the amount of flux applied should be controlled at the optimum level. （3） When using water-soluble flux, special care should be taken to properly clean the boards. ◆Soldering 1. Temperature, time, amount of solder, etc. are specified in accordance with the following recommended conditions, and please contact us about peak temperature when you use lead-free paste. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_prec_e-E02R01 ◆Selection of Flux 1-1. When too much halogenated substance（Chlorine, etc.）content is used to activate the flux, or highly acidic flux is used, an excessive amount of residue after soldering may lead to corrosion of the terminal electrodes or degradation of insulation resistance on the surface of the Inductor. 1-2. Flux is used to increase solderability in flow soldering, but if too much is applied, a large amount of flux gas may be emitted and may detrimentally affect solderability. To minimize the amount of flux applied, it is recommended to use a flux-bubbling system. 1-3. Since the residue of water-soluble flux is easily dissolved by water content in the air, the residue on the surface of Inductor in high humidity conditions may cause a degradation of insulation resistance and therefore affect the reliability of the components. The cleaning methods and the capability of the machines used should also be considered carefully when selecting water-soluble flux. ◆Soldering 1-1. Preheating when soldering Heating: Chip inductor components should be preheated to within 100 to 130℃ of the soldering. Cooling: The temperature difference between the components and cleaning process should not be greater than 100℃. Chip inductors are susceptible to thermal shock when exposed to rapid or concentrated heating or rapid cooling. Therefore, the soldering process must be conducted with a great care so as to prevent malfunction of the components due to excessive thermal shock. Recommended conditions for soldering Pb free soldering ［Reflow soldering］ Temperature profile 300 300 Peak 260℃ Max. Within 10sec. 230℃ Within 10sec. 60sec. 60sec Min. 200 Min. Temperature（℃） Temperature（℃） Preheating Slow cooling 100 0 200 Slow cooling 100 0 Preheating150℃ Heating above 230℃ 60sec. Min. 40sec. Max. ※Ceramic chip components should be preheated to within 100 to 130℃ of the soldering. ※Assured to be reflow soldering for 2 times. Caution 1. The ideal condition is to have solder mass（fillet）controlled to 1/2 to 1/3 of the thickness of the inductor, as shown below: 1/2T～1/3T Inductor Solder Technical considerations T PC board 2. Because excessive dwell times can detrimentally affect solderability, soldering duration should be kept as close to recommended times as possible. ［Wave soldering］ Temperature profile 300 Preheating 120sec. Min. Peak 260℃ Max. Within 10sec. 230～250℃ Within 3sec. 200 Slow cooling 100 Temperature（℃） Temperature（℃） 300 200 120sec. Min. Preheating 150℃ 100 Slow cooling 0 0 ※Ceramic chip components should be preheated to within 100 to 130℃ of the soldering. ※Assured to be wave soldering for 1 time. ※Except for reflow soldering type. Caution 1. Make sure the inductors are preheated sufficiently. 2. The temperature difference between the inductor and melted solder should not be greater than 100 to 130℃. 3. Cooling after soldering should be as gradual as possible. 4. Wave soldering must not be applied to the inductors designated as for reflow soldering only. ［Hand soldering］ Temperature profile 400 400 Peak 350℃ Max. Within 3sec. 230～280℃ Within 3sec. 300 200 Slow cooling 100 0 Preheating 60sec. Min. Temperature（℃） Temperature（℃） 300 ⊿T Slow cooling 200 100 0 Preheating 150℃ Min. 60sec. Min. （※⊿Ｔ≦190℃（ 3216Type max）, ⊿Ｔ≦130℃（ 3225 Type min） ※It is recommended to use 20W soldering iron and the tip is 1φ or less. ※The soldering iron should not directly touch the components. ※Assured to be soldering iron for 1 time. Note: The above profiles are the maximum allowable soldering condition, therefore these profiles are not always recommended. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_prec_e-E02R01 Caution 1. Use a 20W soldering iron with a maximum tip diameter of 1.0 mm. 2. The soldering iron should not directly touch the inductor. 5. Cleaning Precautions ◆Cleaning conditions 1. When cleaning the PC board after the Inductors are all mounted, select the appropriate cleaning solution according to the type of flux used and purpose of the cleaning（e.g. to remove soldering flux or other materials from the production process.） 2. Cleaning conditions should be determined after verifying, through a test run, that the cleaning process does not affect the inductor's characteristics. Technical considerations ◆Cleaning conditions 1. The use of inappropriate solutions can cause foreign substances such as flux residue to adhere to the inductor, resulting in a degradation of the inductor's electrical properties（especially insulation resistance）. 2. Inappropriate cleaning conditions（insufficient or excessive cleaning）may detrimentally affect the performance of the inductors. （1） Excessive cleaning a. In the case of ultrasonic cleaning, too much power output can cause excessive vibration of the PC board which may lead to the cracking of the inductor or the soldered portion, or decrease the terminal electrodes' strength. Thus the following conditions should be carefully checked; Ultrasonic output Below 20W/ℓ Ultrasonic frequency Below 40kHz Ultrasonic washing period 5 min. or less 6. Post cleaning processes Precautions ◆Application of resin coatings, moldings, etc. to the PCB and components. 1. With some type of resins a decomposition gas or chemical reaction vapor may remain inside the resin during the hardening period or while left under normal storage conditions resulting in the deterioration of the inductor's performance. 2. When a resin's hardening temperature is higher than the inductor's operating temperature, the stresses generated by the excess heat may lead to inductor damage or destruction. 3. Stress caused by a resin's temperature generated expansion and contraction may damage inductors. The use of such resins, molding materials etc. is not recommended. 7. Handling Precautions ◆Breakaway PC boards（splitting along perforations） 1. When splitting the PC board after mounting inductors and other components, care is required so as not to give any stresses of deflection or twisting to the board. 2. Board separation should not be done manually, but by using the appropriate devices. ◆General handling precautions 1. Always wear static control bands to protect against ESD. 2. Keep the inductors away from all magnets and magnetic objects. 3. Use non-magnetic tweezers when handling inductors. 4. Any devices used with the inductors（ soldering irons, measuring instruments） should be properly grounded. 5. Keep bare hands and metal products（i.e., metal desk）away from chip electrodes or conductive areas that lead to chip electrodes. 6. Keep inductors away from items that generate magnetic fields such as speakers or coils. ◆Mechanical considerations 1. Be careful not to subject the inductors to excessive mechanical shocks. （1） If inductors are dropped on the floor or a hard surface they should not be used. （2） When handling the mounted boards, be careful that the mounted components do not come in contact with or bump against other boards or components. 8. Storage conditions Precautions ◆Storage 1. To maintain the solderability of terminal electrodes and to keep the packaging material in good condition, care must be taken to control temperature and humidity in the storage area. Humidity should especially be kept as low as possible. Recommended conditions Ambient temperature Below 40℃ Humidity Below 70% RH The ambient temperature must be kept below 30℃. Even under ideal storage conditions inductor electrode solderability decreases as time passes, so inductors should be used within 6 months from the time of delivery. *The packaging material should be kept where no chlorine or sulfur exists in the air. Technical considerations ◆Storage 1. If the parts are stocked in a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of taping/packaging materials may take place. For this reason, components should be used within 6 months from the time of delivery. If exceeding the above period, please check solderability before using the inductors. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_prec_e-E02R01