SAW BANDPASS FILTER PART NO.: ACTF2102-140-SMP03 Features Bandpass filter for base station Ceramic Package for Surface Mounted Technology (SMT) Lead-free Production and RoHS Compliance Package Dimensions Pin Configuration 3 input 4 input Ground 8 output 9 output Ground 1, 5, 6, 10 Ground 2, 7 Case Ground Sign Data (unit: mm) Sign Data (unit: mm) A 7.0 E 0.6 B 5.0 F 1.0 C 1.27 G 1.5 D 2.54 Marking Top View, Laser Marking ACTF * 2102 "ACT”: Manufacturer’s mark “F”: SAW filter “2102”: Part number ” · ”: Terminal 5 “＊”: Iss1 C1u, Lot number (The code shown below varies in a 4-year cycle) Code 1 2 3 4 5 6 7 8 9 10 11 2006 N P Q R S T U V W X Y Z 2007 a b c d e f g h i j k m 2008 n p q r s t u v w x y z 2009 A B C D E F G H J K L M Date 13-7-2011 Page 1 of 4 12 Maximum Ratings Rating Value Unit P 15 dBm DC Voltage VDC 0 V Operating Temperature Range TA -40 ~ +85 °C Storage Temperature Range Tstg -40 ~ +85 °C Source Power Electrical Characteristics Reference temperature: Terminating source impedance: Terminating load impedance: TA = 25 °C ZS = 50 Ω ZL = 50 Ω Characteristic Minimum Typical Maximum Unit Center Frequency fC -- 140.0 -- MHz Insertion Loss (@140.00MHz) IL -- 2.0 3.0 dB 2dB Bandwidth BW2 1.50 1.95 -- MHz 3dB Bandwidth BW3 1.65 2.20 -- MHz 20dB Bandwidth BW20 -- 3.35 3.5 MHz 30dB Bandwidth BW30 -- 3.55 3.75 MHz 40dB Bandwidth BW40 3.80 4.20 MHz 45dB Bandwidth BW45 -- 5.0 10 MHz Rejection (@140.00MHz-1.75MHz) α 25 30 dB Rejection (@140.00MHz+1.75MHz) α 10 15 dB Rejection (@140.00MHz±3.50MHz) α 35 45 dB Rejection (@140.00MHz±8.75MHz) α 40 47 dB Ultimate Rejection α 35 40 -- dB Group Delay (@140MHz) -- 680 1000 ns RoHS Compliant Test Matching Network Iss1 C1u, Electrostatic Sensitive Device Date 13-7-2011 Page 2 of 4 Typical Frequency Response Simith and S11 Iss1 C1u, Date 13-7-2011 Page 3 of 4 Stability Characteristics Test item Condition of test 1 Mechanical shock (a) Drops: 3 times on concrete floor (b) Height: 1.0 m 2 Vibration resistance (a) Frequency of vibration: 10~55Hz (c) Directions: X,Y and Z (b) Amplitude: 1.5 mm (d) Duration: 2 hours 3 Moisture resistance (a) Condition: 40°C, 90~95% R.H. (c) Wait 4 hours before measurement (b) Duration: 96 hours 4 Climatic sequence (a) +70°C for 16 hours (b) +55°C for 24 hours, 90~95% R.H. (c) -25°C for 2 hours (d) +40°C for 24 hours, 90~95% R.H. (e) Wait 4 hours before measurement 5 High temperature exposure (a) Temperature: 70°C (c) Wait 4 hours before measurement 6 Thermal impact (a) +70°C for 30 minutes -25°C for 30 minutes repeated 3 times (b) Wait 4 hours before measurement (b) Duration: 250 hours Requirements: The SAW filer shall remain within the electrical specifications after tests. Remarks SAW devices should not be used in any type of fluid such as water, oil, organic solvent, etc. Be certain not to apply voltage exceeding the rated voltage of components. Do not operate outside the recommended operating temperature range of components. Sudden change of temperature shall be avoided, deterioration of the characteristics can occur. Be careful of soldering temperature and duration of components when soldering. Do not place soldering iron on the body of components. Be careful not to subject the terminals or leads of components to excessive force. SAW devices are electrostatic sensitive. Please avoid static voltage during operation and storage. Ultrasonic cleaning shall be avoided. Ultrasonic vibration may cause destruction of components. Recommended Soldering Profile 1. 2. 3. The specifications of this device are subject to change or obsolescence without notice. Typically, equipment utilizing this device requires emissions testing and government approval, which is the responsibility of the equipment manufacturer. Our liability is only assumed for the Surface Acoustic Wave (SAW) component(s) per se, not for applications, processes and circuits implemented within components or assemblies. Iss1 C1u, Date 13-7-2011 Page 4 of 4