FTR-K1 SERIES POWER RELAY 1 POLE - 16A / Inrush 80A type FTR-K1L Series n FEATURES Low profile - Height: 15.7 mm l Inrush peak current up to 80A (TV-5) l High insulation between coil and contacts: - Insulation distance: 10 mm - Dielectric strength: 5,000VAC - Surge strength: 10,000V l Plastic materials - UL94 flammability class V-0 l Cadmium free relay l RoHS compliant Please see page 5 for more information l n PARTNUMBER INFORMATION [Example] FTR-K1 (a) L (b) D C K 012 W (c) (d) (e) (f ) (g) (a) Relay type FTR-K1 : FTR-K1 Series (b) Operating function L : Latching type (c) Coil type Nil D : 1 coil : 2 coils (d) �������� Contact configuration� �������������� �� A C ��: 1 form A �� ����� � : 1 form C (e) Coil power / Enclosure K : Standard / Flux free (f) ����������� Coil rated voltage� �������� ������� 012 : 5.....24 VDC ��������� ��� Coil rating table at page 3 (g) Contact material W T : AgSnO2 : AgSnO2 (in combination with 1 form A type only, TV-5 rated ) Actual marking does not carry the type name : "FTR" E.g.: Ordering code: FTR-K1LDCK012W Actual marking: K1LDCK012W FTR-K1L FTR-K1SERIES SERIES n SPECIFICATION Item Contact Data FTR-K1L ( ) AK ( ) T FTR-K1L ( ) CK ( ) W Configuration 1 form A 1 form C Construction Single Material AgSnO2 Resistance (initial) ≤ 100mOhm at 1A, 6VDC Contact rating 16A, 250VAC Max. carrying current 440VAC Max. switching power 4,000VA Limited making capacity 80A (type T contact material) *2 Timing Data Insulation 3 x 106 operations minimum Contact rating 100 x 103 operations min. 50 x 103 operations min. 5/80A 250VAC (inrush) 25 x 103 operations minimum (N.O. contact) Rated power (20 °C) 1 coil: 400mW / 2 coils: 600mW Operating temperature range -40 °C to +85 °C (no frost) Set (at nominal voltage) ≤ 15ms (no diode, excluding bounce) Reset (at nominal voltage) ≤ 15ms (no diode, excluding bounce) Min. coil excitation time (at nominal voltage) 30ms Resistance (initial) ≥ 1,000MOhm at 500VDC Dielectric strength Surge strength Other 10 mA, 5VDC Mechanical Electrical Coil Data 16A Max. switching voltage Min. switching load Life *1 Vibration resistance Shock Weight Open contacts 1,000VAC (50/60Hz) 1min Contacts to coil 5,000VAC (50/60Hz) 1min Coil to contacts 10,000V / 1.2 x 50µs standard wave Misoperation ≥ 1µs 10 to 55Hz double amplitude 0.7mm Endurance 10 to 55Hz double amplitude 1.5mm Misoperation ≥ 1µs Min. 100m/s2 (11±1ms) Endurance Min. 1,000m/s2 (6±1ms) Approximately 13g *1 Need to consider the heat from PCB when max. current is more than 10A. *2 Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental contions and expected reliability levels. FTR-K1SERIES SERIES FTR-K1L n COIL RATING Coil Code 1 coil Rated Coil Voltage Operating voltage Coil Resistance (VDC) (VDC) +/- 10% (Ohm) 2 coils Operating voltage (VDC) Coil Resistance +/- 10% (Ohm) 005 5 3.5 63 3.5 42 012 12 8.4 360 8.4 240 024 24 16.8 1,440 16.8 960 Note: All values in the table are valid for 20°C and zero contact current. * Specified operate values are valid for pulse wave voltage. n SAFETY STANDARDS Type Compliance Contact rating UL UL 508 Flammability: UL 94-V0 (plastics) CSA C22.2 No. 14 VDE 0435, 0631, 0860 16A, 250VAC, resistive 100,000 operations (1 form A) 16A, 250VAC, resistive 50,000 operations (1 form C) FTR-K1SERIES SERIES FTR-K1L n COIL POLARITY Version 1 coil 2 coils Terminal No. 4 6 4 5 Set - + - + Reset + - + 6 - n DIMENSIONS l Dimensions l Schematics (BOTTOM VIEW) l PC board mounting hole layout Unit: mm a) for 1 form C version only b) for 2 coils version only FTR-K1SERIES SERIES FTR-K1L RoHS Compliance and Lead Free Information 1. General Information l l l l All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including amendments. Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005. (Amendment to Directive 2002/95/EC) All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. 2. Recommended Lead Free Solder Profile Recommended solder Sn-3.0Ag-0.5Cu. l Flow Solder condition: Pre-heating: Soldering: maximum 120˚C dip within 5 sec. at 260˚C solder bath Solder by Soldering Iron: Soldering Iron Temperature: maximum 360˚C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. l 4. Tin Whiskers Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. l FTR-K1SERIES SERIES FTR-K1L Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: [email protected] Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: [email protected] Web: emea.fujitsu.com/components/ North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: [email protected] Web: http://us.fujitsu.com/components Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: [email protected] Web: http://www.fujitsu.com/sg/services/micro/components/ ©2009 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users’ own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. November 6, 2009