ORing IAP-420 Industrial ieee 802.11 b/g/n wireless access point Datasheet

Designed for Rugged Excellence
IAP-420 / IAP-420+
Industrial IEEE 802.11 b/g/n wireless access point
with 2x10/100Base-T(X)
Features

High Speed Air Connectivity: WLAN interface support up to
150 Mbps link speed

Highly Security Capability: WEP/WPA/WPA-PSK(TKIP,AES)/
WPA2/WPA2-PSK(TKIP,AES)/802.1X Authentication supported

Provide 2 port 10/100Base-T(X) Ethernet ports

Support X-Roaming < 100 ms

Support AP/Client/Bridge/AP-Client Mode

Support Multiple-SSID to 4 SSID

Secured Management by HTTPs

Wireless connecting status monitoring

Event Warning by Syslog, Email, SNMP Trap

1KV isolation for PoE P.D. port of IAP-420+

Rigid IP-30 housing design

DIN-Rail and Wall-mount enabled
Introduction
IAP-420 / IAP-420+ series are reliable 802.11 b/g/n WLAN Access Point with 2 ports LAN.
MAC filters for security control.
It supports 802.1X and
It can be configured to operate in AP/Bridge/Repeater/AP-Client mode.
to configure IAP-420 / IAP-420+ series by WEB interface via LAN port or WLAN interface.
You are able
In addition, IAP-420+ also
provides P.D. feature on ETH1 which is fully compliant with IEEE802.3af PoE P.D. specification.
Therefore, IAP-420 /
IAP-420+ series are one of the best communication solutions for wireless applications on the industrial network.
* All specifications are subject to change without notice.
Designed for Rugged Excellence
Application
In practical operation of wireless access point, Windows utility (Open-Vision) is supported.
you to search and configure IP of access point on the industrial network.
In addition, the wireless access point support
various kinds of operation modes include AP/ Bridge/Repeater/AP-Client mode.
PoE P.D. feature to extend the layout up to 100 meters.
This utility is very helpful for
IAP-420 / IAP-420+ series also support
You can build up the wireless network easily.
Dimension
* All specifications are subject to change without notice.
Designed for Rugged Excellence
Specifications
ORing WLAN Access Point
IAP-420
Model
IAP-420+
Physical Ports
10/100 Base-T(X) Ports in
2
RJ45 Auto MDI/MDIX
Present at ETH1
Fully compliant with IEEE 802.3af
PoE P.D. port
Power Device specification
-
Over load & short circuit protection
Isolation Voltage: 1000 VDC min.
Isolation Resistance : 108 ohms min
WLAN interface
Operating Mode
AP/Bridge/AP-Client
Antenna Connector
1 x External reverse SMA-type antenna connector
Radio Frequency Type
DSSS, OFDM
Modulation
IEEE802.11b: CCK, DQPSK, DBPSK
IEEE802.11g/n: OFDM with BPSK, QPSK, 16QAM, 64QAM
America / FCC:
Frequency Band
2.412~2.462 GHz (11 channels )
Europe CE / ETSI:
2.412~2.472 GHz ( 13 channels )
802.11b: 1/2/5.5/11 Mbps
Transmission Rate
802.11g: 6/9/12/18/24/36/48/54 Mbps
802.11n(40MHz): UP to 150 Mbps
802.11b: 13.5dBm ± 1.5dBm
Transmit Power
802.11g: 13.5dBm ± 1.5dBm
802.11n(2.4G@20MHz): 13.5dBm ± 1.5dBm
802.11n(2.4G@40MHz): 13.5dBm ± 1.5dBm
802.11b: -90dBm ± 2dBm@1Mbps
Receiver Sensitivity
802.11g: -72dBm ± 2dBm@54Mbps
802.11n(2.4G@40MHz,MCS7): -68dBm ± 2dBm
WEP: (64-bit, 128-bit key supported)
WPA/WPA2:802.11i (WEP and AES encryption)
Encryption Security
WPA-PSK (256-bit key pre-shared key supported)
802.1X Authentication supported
TKIP encryption
Wireless Security
SSID broadcast disable and enable
Protocol Support
Protocol
ARP,BOOTP, DHCP, DNS, HTTP, IP, ICMP, SNTP, TCP, UDP, 802.1X, SNMP, STP
LED indicators
Power indicator
10/100Base-T(X) RJ45 port
indicator
WLAN LEDs
LED x 3, PWR 1, 2, (PoE):
Green On: Power is on and functioning Normally.
LED x 2 , Green for port Link/Act at 100Mbps.
WLAN Link /ACT: Green: Blinking
Power
Redundant Input power
Dual DC inputs.
12~48VDC on 4-pin terminal block
* All specifications are subject to change without notice.
Designed for Rugged Excellence
Power consumption (Typ.)
4watts
Overload current protection
Present
Reverse polarity protection
Present
Physical Characteristic
Enclosure
IP-30
Dimension (W x D x H)
41(W)x81(D)x95(H) mm
Weight (g)
292
297
Environmental
Storage Temperature
-40 to 85oC (-40 to 185oF)
Operating Temperature
-10 to 60oC (14 to 140oF)
Operating Humidity
5% to 95% Non-condensing
Regulatory approvals
EMI
EMS
FCC Part 15, CISPR (EN55022) class A
EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5
(Surge), EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
Shock
IEC60068-2-27
Free Fall
IEC60068-2-32
Vibration
IEC60068-2-6
Safety
EN60950-1
Warranty
3 years
* All specifications are subject to change without notice.
Designed for Rugged Excellence
Ordering Information
IAP- A B 0 C
Code Definition
Wireless Mode
10/100 Base-T(X) Port Number
PoE Identification
- 1: 802.11 b/g
-"2": 2 ports
-"+": PoE P.D. present at
- 2: 802.11 a
Option
ETH1
- 3: 802.11 a/b/g
- 4: 802.11 b/g/n
- 5: 802.11 a/n
- 6: 802.11 a/b/g/n
Available
Model Name
Description
IAP-420_US
Industrial IEEE 802.11 b/g/n wireless access point with 2x10/100Base-T(X), US band
IAP-420_EU
Industrial IEEE 802.11 b/g/n wireless access point with 2x10/100Base-T(X), EU band
Model
IAP-420+_US
IAP-420+_EU
Industrial IEEE 802.11 b/g/n wireless access point with 2x10/100Base-T(X), 1-port PoE P.D.,
US band
Industrial IEEE 802.11 b/g/n wireless access point with 2x10/100Base-T(X), 1-port PoE P.D.,
EU band
Packing List
O

IAP-420/420+ x 1

CD x 1

Quick Installation Guide x 1

Antenna x 1

Din-Rail Kit x 1

Wall-Mount Kit x 1
Optional Accessories
O

DR-45 series : 45 Watts power supply

DR-75 series : 75 Watts power supply

DR-120 series : 120 Watts power supply

WLAN RF Antenna (Omni-directional) series

RF Antenna Base (Magnetic) series

RF Cable series

RF Surge Protector
* All specifications are subject to change without notice.
Similar pages