AD ADN2892ACPZ-RL7 3.3 v, 4.25 gbps, limiting amplifier Datasheet

3.3 V, 4.25 Gbps,
Limiting Amplifier
ADN2892
Data Sheet
FEATURES
GENERAL DESCRIPTION
Input sensitivity: 3.5 mV p-p
70 ps rise/fall times
CML outputs: 750 mV p-p differential
Bandwidth selectable for multirate 1×/2×/4× FC modules
Optional LOS output inversion
Programmable LOS detector: 3.5 mV to 35 mV
Rx signal strength indicator (RSSI)
SFF-8472-compliant average power measurement
Single-supply operation: 3.3 V
Low power dissipation: 160 mW
Available in space-saving, 3 mm × 3 mm, 16-lead LFCSP
Extended temperature range: −40°C to +95°C
SFP reference design available
The ADN2892 is a 4.25 Gbps limiting amplifier with integrated
loss of signal (LOS) detection circuitry and a received signal
strength indicator (RSSI). This part is optimized for Fibre
Channel (FC) and Gigabit Ethernet (GbE) optoelectronic
conversion applications. The ADN2892 has a differential input
sensitivity of 3.5 mV p-p and accepts up to a 2.0 V p-p
differential input overload voltage. The ADN2892 has current
mode logic (CML) outputs with controlled rise and fall times.
The ADN2892 has a selectable low-pass filter with a −3 dB
cutoff frequency of 1.5 GHz. By setting BW_SEL to Logic 0, the
filter can limit the relaxation oscillation of a low cost CD laser
used in a legacy 1 Gbps FC transmitter. The limited BW also
reduces the rms noise and in turn improves the receiver optical
sensitivity for a lower data rate application, such as 1× FC and
GbE.
APPLICATIONS
1×, 2×, and 4× FC transceivers
SFP/SFF/GBIC optical transceivers
GbE transceivers
Backplane receivers
By monitoring the bias current through a photodiode, the onchip RSSI detector measures the average power received with
2% typical linearity over the entire valid input range of the
photodiode. The on-chip RSSI detector facilitates SFF-8472compliant optical transceivers by eliminating the need for
external RSSI detector circuitry.
Additional features include a programmable loss-of-signal
(LOS) detector and output squelch. The ADN2892 is available
in a 3 mm × 3 mm, 16-lead LFCSP.
FUNCTIONAL BLOCK DIAGRAM
AVCC
AVEE
BW_SEL
SQUELCH
DRVCC
DRVEE
ADN2892
50W
50W
OUTP
PIN
NIN
OUTN
LPF
50W
50W
V+
3.5kW
PD_VCC
PD_CATHODE
VREF
LOS
RSSI/LOS
DETECTOR
THRADJ
RSSI_OUT
LOS_INV
10kW
ADuC7020
04986-001
ADN2882
Figure 1. RSSI Function Capable—Applications Setup Block Diagram
Rev. A
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2005–2013 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADN2892
Data Sheet
TABLE OF CONTENTS
Specifications..................................................................................... 3
Squelch Mode ............................................................................. 10
Absolute Maximum Ratings ............................................................ 5
BW_SEL (Bandwidth Selection) Mode ................................... 10
Thermal Resistance ...................................................................... 5
LOS_INV (Lose of Signal_Invert) Mode ................................ 10
ESD Caution .................................................................................. 5
Applications..................................................................................... 11
Pin Configuration and Function Descriptions ............................. 6
PCB Design Guidelines ............................................................. 11
Typical Performance Characteristics ............................................. 7
Pad Coating and Pb-Free Soldering ........................................ 12
Theory of Operation ...................................................................... 10
Outline Dimensions ....................................................................... 13
Limiting Amplifier ..................................................................... 10
Ordering Guide .......................................................................... 13
Loss-of-Signal (LOS) Detector ................................................. 10
Received Signal Strength Indicator (RSSI) .............................. 10
REVISION HISTORY
7/13—Rev. 0 to Rev. A
Change to Output Voltage Swing Parameter, Table 1 ................... 3
Changes to Figure 2 ........................................................................... 6
Updated Outline Dimensions ........................................................13
Changes to Ordering Guide ...........................................................13
4/05—Revision 0: Initial Version
Rev. A | Page 2 of 16
Data Sheet
ADN2892
SPECIFICATIONS
Test Conditions: VCC = 2.9 V to 3.6 V, VEE = 0 V, TA = −40°C to +95°C, unless otherwise noted.
Table 1.
Parameter
QUANTIZER DC CHARACTERISTICS
Input Voltage Range
Input Common Mode
Peak-to-Peak Differential Input Range
Input Sensitivity
Input Offset Voltage
Input RMS Noise
Input Resistance
Input Capacitance
QUANTIZER AC CHARACTERISTICS
Input Data Rate
Small Signal Gain
S11
S22
Random Jitter
Deterministic Jitter
Low Frequency Cutoff
Power Supply Rejection
LOSS OF SIGNAL DETECTOR (LOS)
LOS Assert Level
Electrical Hysteresis
LOS Assert Time
LOS Deassert Time
RSSI
Input Current Range
RSSI Output Linearity
Gain
Offset
Compliance Voltage (At PD_CATHODE)
Min
VCC − 1.2
2.1
6.6
Unit
Test Conditions/Comments
VCC − 0.2
2.7
2.0
V
V
V p-p
mV p-p
µV
µV rms
Ω
pF
At PIN or NIN, dc-coupled
DC-coupled
PIN − NIN, ac-coupled
PIN − NIN, BER ≤ 1 × 10−10
4.25
51
−10
−10
3.0
10
30
45
2.9
22.4
2.5
2.8
Max
3.5
100
235
50
0.65
1.0
3.5
35
5.0
5.0
950
62
5
3.9
21.0
mV p-p
mV p-p
dB
dB
ns
ns
1000
µA
%
mA/mA
nA
V
V
VCC − 0.4
VCC − 0.9
1.5
2.9
−40
600
Gbps
dB
dB
dB
ps rms
ps p-p
kHz
dB
4.8
55.0
2
1.0
145
BW_SEL (BANDWIDTH SELECTION)
Channel Bandwidth
POWER SUPPLIES
VCC
ICC
OPERATING TEMPERATURE RANGE
CML OUTPUT CHARACTERISTICS
Output Impedance
Output Voltage Swing
Output Rise and Fall Time
Typ
GHz
Single-ended
Differential
Differential, f < 4.25 GHz
Differential, f < 4.25 GHz
Input ≥ 10 mV p-p, 4× FC, K28.7 pattern
Input ≥ 10 mV p-p, 4× FC, K28.5 pattern
100 kHz < f < 10 MHz
RTHRADJ = 100 kΩ
RTHRADJ = 1 kΩ
1.0 Gbps, PRBS 223 − 1
4× FC, PRBS 223 − 1
DC-coupled
DC-coupled
5 µA ≤ IIN ≤ 1000 µA
IRSSI/IPD_CATHODE
IPD_CATHODE = 5 µA
IPD_CATHODE = 1000 µA
−3 dB cutoff frequency of the on-chip,
two-pole, low-pass filter, when BW_SEL = 0
3.3
48
+25
3.6
54
+95
V
mA
°C
TMIN to TMAX
50
750
70
940
103
Ω
mV p-p
ps
Single-ended
Differential
20% to 80%
Rev. A | Page 3 of 16
ADN2892
Parameter
LOGIC INPUTS (SQUELCH, LOS_INV, AND
BW_SEL)
VIH, Input High Voltage
VIL, Input Low Voltage
Input Current (SQUELCH, LOS_INV)
Data Sheet
Min
VOL, Output Low Voltage
Max
Unit
0.8
39
V
V
µA
−38
µA
2.0
Input Current (BW_SEL)
LOGIC OUTPUTS (LOS)
VOH, Output High Voltage
Typ
2.4
V
0.4
Rev. A | Page 4 of 16
V
Test Conditions/Comments
IINH, VIN = 2.4 V, 100 kΩ pull-down,
on-chip resistor
IINL, VIN = 0.0 V, 100 kΩ pull-up,
on-chip resistor
Open drain output, 4.7 kΩ − 10 kΩ
pull-up resistor to VCC
Open drain output, 4.7 kΩ − 10 kΩ
pull-up resistor to VCC
Data Sheet
ADN2892
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
Power Supply Voltage
Minimum Voltage
(All Inputs and Outputs)
Maximum Voltage
(All Inputs and Outputs)
Storage Temperature
Operating Temperature Range
Production Soldering Temperature
Junction Temperature
Rating
4.2 V
VEE − 0.4 V
VCC + 0.4 V
−65°C to +150°C
−40°C to +95°C
J-STD-20
125°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only and functional operation of the device at these or
any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL RESISTANCE
θJA is specified for 4-layer PCB with exposed paddle soldered
to GND.
Table 3.
Package Type
3 mm × 3 mm, 16-lead LFCSP
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. A | Page 5 of 16
θJA
28
Unit
°C/W
ADN2892
Data Sheet
NIN 3
14 RSSI_OUT
ADN2892
TOP VIEW
(Not to Scale)
AVEE 4
12 DRVCC
11 OUTP
10 OUTN
LOS 8
LOS_INV 7
THRADJ 5
BW_SEL 6
9 DRVEE
NOTES
1. THERE IS AN EXPOSED PAD ON THE BOTTOM OF
THE PACKAGE THAT MUST BE CONNECTED TO
THE GND PLANE WITH FILLED VIAS.
04986-002
PIN 2
13 SQUELCH
16 PD_CATHODE
AVDD 1
15 PV_VCC
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 2. Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
Mnemonic
AVCC
PIN
NIN
AVEE
THRADJ
BW_SEL
LOS_INV
I/O Type 1
P
AI
AI
P
AO
DI
DI
8
9
10
11
12
13
14
15
16
Exposed Pad
LOS
DRVEE
OUTN
OUTP
DRVCC
SQUELCH
RSSI_OUT
PD_VCC
PD_CATHODE
Pad
DO
P
DO
DO
P
DI
AO
P
AO
P
1
Description
Analog Power Supply.
Differential Data Input, Positive Port, 50 Ω On-Chip Termination.
Differential Data Input, Negative Port, 50 Ω On-Chip Termination.
Analog Ground.
LOS Threshold Adjust Resistor.
With one 100 kΩ on-chip, pull-up resistor, BW_SEL = 0 for 1×/2× FC, BW_SEL = 1 for 4× FC.
With one 100 kΩ on-chip, pull-down resistor, LOS_INV = 1 inverts the LOS output
to be active low for SFF.
LOS Detector Output, Open Collector.
Output Buffer Ground.
Differential Data Output, CML, Negative Port, 50 Ω, On-Chip Termination.
Differential Data Output, CML, Positive Port, 50 Ω, On-Chip Termination.
Output Buffer Power Supply.
Disable Outputs, 100 kΩ On-Chip, Pull-Down Resistor.
Average Current Output.
Power Input for RSSI Measurement.
Photodiode Bias Voltage.
Connect to Ground.
P = power; DI = digital input; DO = digital output; AI = analog input; and AO = analog output.
Rev. A | Page 6 of 16
Data Sheet
ADN2892
TYPICAL PERFORMANCE CHARACTERISTICS
0.06
+95°C
150mV/DIV
TRIP AND RELEASE (V)
0.05
+25°C
0.04
0.03
–40°C
0.02
DEASSERTION
–40°C
04986-012
+25°C
+95°C
0
1k
50ps/DIV
04986-026
0.01
ASSERTION
10k
RTH (Ω)
100k
Figure 6. LOS Trip and Release vs. RTH at 4.25 Gbps
Figure 3. Eye of ADN2892 @ 25°C, 4.25 Gbps, and 10 mV Input
8
1GBPS
6
5
4.25GBPS
4
3
2
0
1k
50ps/DIV
Figure 4. Eye of ADN2892 @ 95°C, 4.25 Gbps, and 10 mV Input
04986-027
1
04986-023
150mV/DIV
ELECTRICAL HYSTERESIS (dB)
7
10k
RTH (Ω)
100k
Figure 7. LOS Electrical Hysteresis vs. RTH at 25°C
16
14
150mV/DIV
12
SAMPLES
10
8
6
200ps/DIV
2
04986-024
04986-010
4
0
5.8 6.0 6.2 6.4 6.6 6.8 7.0 7.2 7.4 7.6 7.8 8.0 8.2 8.4 8.6
ELECTRICAL HYSTERESIS (dB)
Figure 5. Eye of ADN2892 at 25°C, 1.063 Gbps, and 10 mV Input (BW_SEL = 0)
Rev. A | Page 7 of 16
Figure 8. Sample Lot Distribution—Worst-Case Condition:
Conditions = 4.25 Gbps, 100 kΩ @ −40°C, 3.6 V
ADN2892
Data Sheet
1200
4.0
3.5
RSSI OUTPUT CURRENT (µA)
1000
2.5
2.0
1.5
1.0
600
400
200
04986-028
0.5
0
1.0
800
1.5
2.0
2.5
3.0
RATE (Gbps)
3.5
4.0
04986-017
JITTER (ps)
3.0
0
4.5
0
400
600
800
1000
200
PD_CATHODE CURRENT (PHOTODIODE CURRENT) (µA)
Figure 12. RSSI Output vs. Average Photodiode Current
Figure 9. Random Jitter vs. Data Rate
60
18
16
RSSI OUTPUT CURRENT (µA)
50
14
JITTER (ps)
12
10
8
6
4
40
30
20
1.5
2.0
2.5
3.0
RATE (Gbps)
3.5
4.0
0
4.5
0
Figure 10. Deterministic Jitter vs. Data Rate
50
40
30
20
0
100k
04986-016
POWER SUPPLY-NOISE REJECTION (dB)
60
1M
SUPPLY-NOISE FREQUENCY
COMPLIANCE VOLTAGE REFERRED TO VCC (V)
Figure 13. RSSI Output vs. Average Photodiode Current (Zoomed)
70
10
10
20
30
40
50
PD_CATHODE CURRENT (PHOTODIODE CURRENT) (µA)
–0.15
–0.20
–0.25
–0.30
–0.35
–0.40
–0.45
–0.50
–0.55
–0.60
04986-018
0
1.0
04986-020
04986-029
10
2
–0.65
–0.70
10M
0
100
200
300 400 500 600 700
INPUT CURRENT (µA)
800
Figure 14. PD_CATHODE Compliance Voltage vs.
Input Current RSSI (Refer to VCC)
Figure 11. PSRR vs. Supply-Noise Frequency
Rev. A | Page 8 of 16
900
1000
Data Sheet
ADN2892
900
49.0
800
600
48.0
ICC (mA)
5µA REFERRED OFFSET (nA)
48.5
700
500
400
47.5
47.0
300
200
0
–40
–20
0
20
40
TEMPERATURE (°C)
60
80
100
46.0
–40
5.0
4.5
3.5
3.0
2.5
+100°C
+30°C
1.5
1.0
–40°C
0
0
200
400
600
PD_CATHODE CURRENT (µA)
800
04986-021
RSSI LINEARITY (%)
4.0
0.5
–20
0
20
40
TEMPERATURE (°C)
60
Figure 17. ADN2892 ICC Current vs. Temperature
Figure 15. RSSI Offset—Difference Between Measured RSSI Output and
PD_CATHODE (Input) Current of 5 µA
2.0
04986-025
04986-019
46.5
100
1000
Figure 16. RSSI Linearity % vs. PD_CATHODE Current
Rev. A | Page 9 of 16
80
100
ADN2892
Data Sheet
THEORY OF OPERATION
LIMITING AMPLIFIER
RECEIVED SIGNAL STRENGTH INDICATOR (RSSI)
Input Buffer
The ADN2892 has an on-chip, RSSI circuit. By monitoring the
current supplied to the photodiode, the RSSI circuit provides an
accurate, average power measurement. The output of the RSSI is
a current that is directly proportional to the average amount of
PIN photodiode current. Placing a resistor between the
RSSI_OUT pin and GND converts the current to a GND
referenced voltage. This function eliminates the need for
external RSSI circuitry for SFF-8472-compliant optical
receivers. For more information, see Figure 12 to Figure 16.
The ADN2892 limiting amplifier provides differential
inputs (PIN/NIN), each with a single-ended, on-chip 50 Ω
termination. The amplifier can accept either dc-coupled or
ac-coupled signals; however, an ac-coupled signal is
recommended. Using a dc-coupled signal, the amplifier
needs a nominal VCC − 0.7 V common-mode voltage and
±0.5 V headroom. If the input common-mode voltage is 2.4 V,
the available headroom is reduced down to ±0.3 V.
The ADN2892 limiting amplifier is a high gain device. It is
susceptible to dc offsets in the signal path. The pulse width
distortion presented in the NRZ data or a distortion generated
by the TIA may appear as dc offset or a corrupted signal to the
ADN2892 inputs. An internal offset correction loop can
compensate for certain levels of offset.
CML Output Buffer
The ADN2892 provides differential CML outputs, OUTP and
OUTN. Each output has an internal 50 Ω termination to VCC.
LOSS-OF-SIGNAL (LOS) DETECTOR
The on-chip LOS circuit drives LOS to logic high when the
input signal level falls below a user-programmable threshold.
The threshold level can be set anywhere from 3.5 mV pp to 35
mV pp typical by a resistor connected between the THRADJ
pin and VEE. See Figure 6 and Figure 7 for the LOS threshold
vs. THRADJ. The ADN2892 LOS circuit has an electrical
hysteresis greater than 2.5 dB to prevent chatter at the LOS
signal. The LOS output is an open-collector output that must be
pulled up externally with a 4.7 kΩ to 10 kΩ resistor.
Connect the PD_VCC, PD_CATHODE, and RSSI_OUT pins to
AVCC to disable the RSSI feature.
SQUELCH MODE
Driving the SQUELCH input to logic high disables the limiting
amplifier outputs. Using LOS output to drive the SQUELCH
input, the limiting amplifier outputs stop toggling anytime a
signal input level to the limiting amplifier drops below the
programmed LOS threshold.
The SQUELCH pin has a 100 kΩ, internal pull-down resistor.
BW_SEL (BANDWIDTH SELECTION) MODE
Driving the BW_SEL input signal to logic high, the amplifier
provides a 3.8 GHz bandwidth. Driving the BW_SEL input
signal to logic low, the amplifier accepts input signals through a
1.5 GHz, 2-pole, low-pass filter that improves receiving
sensitivity.
The low-pass filter reduces the possible relaxation oscillation of
low speed, low cost laser source by limiting the input signal
bandwidth.
The BW_SEL pin has a 100 kΩ, on-chip pull-up resistor. Setting
the BW_SEL pin open disables the low-pass filter.
LOS_INV (LOSE OF SIGNAL_INVERT) MODE
Some applications, such as SFF, need the LOS assertion and
deassertion voltage reversed. When the LOS_INV pin is pulled
to logic high, the LOS output assertion is pulled down to
electrical low.
The LOS_INV pin has a 100 kΩ on-chip, pull-down resistor.
Rev. A | Page 10 of 16
Data Sheet
ADN2892
APPLICATIONS
PCB DESIGN GUIDELINES
The exposed pad should connect to the GND plane using filled
vias so that solder does not leak through the vias during reflow.
Using filled vias in parallel under the package greatly reduces
the thermal resistance and enhances the reliability of the
connectivity of the exposed pad to the GND plane during
reflow.
Proper RF PCB design techniques must be used to ensure
optimal performance.
Output Buffer Power Supply and Ground Planes
Pin 9 (DRVEE) and Pin 12 (DRVCC) are the power supply and
ground pins that provide current to the differential output
buffer. To reduce possible series inductance, Pin 9, which is the
ground return of the output buffer, should connect to ground
directly. If the ground plane is an internal plane and
connections to the ground plane are vias, multiple vias in
parallel to ground can reduce series inductance.
To reduce power supply noise, a 10 μF electrolytic decoupling
capacitor between power and ground should be close to where
the 3.3 V supply enters the PCB. The other 0.1 μF and 1 nF
ceramic chip decoupling capacitors should be close to the VCC
and VEE pins to provide optimal supply decoupling and a
shorter current return loop.
Similarly, to reduce the possible series inductance, Pin 12,
which supplies power to the high speed differential
OUTP/OUTN output buffer, should connect to the power plane
directly. If the power plane is an internal plane and connections
to the power plane are vias, multiple vias in parallel can reduce
the series inductance, especially on Pin 12. See Figure 18 for the
recommended connections.
VCC
16
C2
NIN
AVEE
2
CONNECT
EXPOSED
PAD TO
GND
11
10
4
9
5
C12
C7
12
3
6
R2
RSSI MEASUREMENT
TO ADC
13
7
C8
DRVCC
OUTP C3
OUTN C4
TO HOST
BOARD
DRVEE
8
LOS
PIN
14
ADN2892
THRADJ
ADN2882
C1
15
C10
VCC
1
LOS_INV
AVCC
R1
C1–C4, C11: 0.01F X5R/X7R DIELECTRIC, 0201 CASE
C5, C7, C9, C10, C12: 0.1F X5R/X7R DIELECTRIC, 0402 CASE
C6, C8: 1nF X5R/X7R DIELECTRIC, 0201 CASE
R3
4.7k TO 10k
ON HOST BOARD
VCC
TO ADuC7020
Figure 18. Typical ADN2892 Applications Circuit
Rev. A | Page 11 of 16
04986-008
C6
BW_SEL
C5
SQUELCH
VCC
PD_VCC
PD_CATHODE
0.1F
RSSI_OUT
C9
VCC
ADN2892
Data Sheet
PCB Layout
Soldering Guidelines for the LFCSP
Figure 19 shows the recommended PCB layout. The 50 Ω
transmission lines are the traces that bring the high frequency
input and output signals (PIN, NIN, OUTP, and OUTN) from a
terminated source to a terminated load with minimum
reflection. To avoid a signal skew between the differential
traces, each differential PIN/NIN and OUTP/OUTN pair
should have matched trace lengths from a differential source to
a differential load. C1, C2, C3, and C4 are ac coupling
capacitors in series with the high speed, signal input/output
paths. To minimize the possible mismatch, the ac coupling
capacitor pads should be the same width as the 50 Ω
transmission line trace width. To reduce supply noise, a 1 nF
decoupling capacitor should be placed as close as possible to the
VCC pins on the same layer and not through vias. A 0.1 μF
decoupling capacitor can be placed on the bottom of the PCB
directly underneath the 1 nF capacitor. All high speed, CML
outputs have internal 50 Ω resistor termination between the
output pin and VCC. The high speed inputs, PIN and NIN, also
have the internal 50 Ω termination to an internal reference
voltage.
The lands on the 16-lead LFCSP are rectangular. The PCB pad
for these should be 0.1 mm longer than the package land length
and 0.05 mm wider than the package land width. The land
should be centered on the pad. This ensures that the solder joint
size is maximized. The bottom of the LFCSP has a central
exposed pad. The pad on the printed circuit board should be at
least as large as the exposed pad. Users must connect the
exposed pad to VEE using filled vias so that solder does not
leak through the vias during reflow. This ensures a solid
connection from the exposed pad to VEE.
PAD COATING AND PB-FREE SOLDERING
Table 5.
Pad Coating
Pb-Free Reflow Portfolio
Matt-Tin
J-STD-20B
As with any high speed, mixed-signal design, keep all high
speed digital traces away from sensitive analog nodes.
R1, C9, C10 ON BOTTOM
DVCC GND DOUBLE-VIAS TO REDUCE
INDUCTANCE TO SUPPLY
AND GND
TO ROSA
GND
AVCC
PLACE C5 ON
BOTTOM OF BOARD
UNDERNEATH C6
C1
1
PLACE C7 ON
BOTTOM OF BOARD
UNDERNEATH C8
EXPOSED PAD
C6
C8
C3
PIN
NIN
OUTN
C2
C4
TRANSMISSION LINES SAME
WIDTH AS AC COUPLING
CAPS TO REDUCE REFLECTIONS
DOUBLE-VIA TO GND
TO REDUCE INDUCTANCE
VIA TO C12, R2
ON BOTTOM
VIAS TO BOTTOM
Figure 19. Recommended ADN2892 PCB Layout (Top View)
Rev. A | Page 12 of 16
04986-009
4mm
OUTP
FILLED VIAS TO
GND
Data Sheet
ADN2892
OUTLINE DIMENSIONS
0.60 MAX
3.00
BSC SQ
BOTTOM VIEW
13
12
0.45
TOP
VIEW
2.75
BSC SQ
SEATING
PLANE
9
4
8
5
0.05 MAX
0.02 NOM
0.30
0.23
0.18
*1.65
1.50 SQ
1.35
0.25 MIN
1.50 REF
0.80 MAX
0.65 TYP
0.90
0.85
0.80
1
EXPOSED
PAD
0.50
BSC
12° MAX
16
PIN 1
INDICATOR
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
0.20 REF
*COMPLIANT TO JEDEC STANDARDS MO-220-VEED-2
EXCEPT FOR EXPOSED PAD DIMENSION.
07-17-2008-A
PIN 1
INDICATOR
0.50
0.40
0.30
Figure 20. 16-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
3 mm × 3 mm Body, Very Thin Quad
(CP-16-3)
Dimensions shown in millimeters
ORDERING GUIDE
Model 1
ADN2892ACPZ-500RL7
ADN2892ACPZ-RL7
ADN2892ACPZ-RL
EVAL-ADN2892EBZ
1
Temperature Range
–40°C to +95°C
–40°C to +95°C
–40°C to +95°C
Package Description
16-Lead LFCSP_VQ, 500 pieces
16-Lead LFCSP_VQ, 1,500 pieces
16-Lead LFCSP_VQ,5,000 pieces
Evaluation Board
Z = RoHS-Compliant Part.
Rev. A | Page 13 of 16
Package Option
CP-16-3
CP-16-3
CP-16-3
Branding
F05
F05
F05
ADN2892
Data Sheet
NOTES
Rev. A | Page 14 of 16
Data Sheet
ADN2892
NOTES
Rev. A | Page 15 of 16
ADN2892
Data Sheet
NOTES
©2005–2013 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D04986-0-7/13(A)
Rev. A | Page 16 of 16
Similar pages