ALT5020 High Efficiency UMTS E800 (Band 20) LTE Linear PAM ADvanced product information - Rev 0.0 FEATURES • LTE Compliant • High Efficiency (LTE waveform): • 42% @ POUT = +27.7 dBm • Optimized for SMPS Supply • Low Leakage Current in Shutdown Mode: <5 µA • Internal Voltage Regulator • Integrated “daisy chainable” directional coupler with CPLIN and CPLOUT Ports • Optimized for a 50 Ω System • Internal DC blocks on IN/OUT RF ports • 1.8 V Control Logic • RoHS Compliant Package, 260 oC MSL-3 ALT5020 10 Pin 3 mm x 3 mm x 0.9 mm Surface Mount Module APPLICATIONS • Wireless Handsets and Data Devices for: • LTE (B20) PRODUCT DESCRIPTION The ALT5020 PA is designed to provide highly linear output for LTE handsets and data devices with high efficiency at high power mode. This ANADIGICS PA can be used with an external switch mode power VBATT supply (SMPS) to improve its efficiency and reduce current consumption further at high and low output powers. The device is manufactured on an advanced RFIN InGaP HBT MMIC technology offering state-of-theart reliability, temperature stability, and ruggedness. There are three selectable bias modes that optimize efficiency for different output power levels, and a shutdown mode with low leakage current, which VMODE2 increases handset talk and standby time. The selfcontained 3 mm x 3 mm x 0.9 mm surface mount package incorporates matching networks optimized for VMODE1 output power, efficiency, and linearity in a 50 Ω system. VEN GND at Slug (pad) 1 10 2 9 RFOUT 8 CPLIN 4 7 GND 5 6 CPLOUT 3 CPL Bias Control Voltage Regulation Figure 1: Block Diagram 09/2013 VCC ALT5020 VBATT 1 10 RFIN 2 9 RFOUT VMODE2 3 8 CPLIN VMODE1 4 7 GND VEN 5 6 CPLOUT Figure 2: Pinout (X-ray Top View) Table 1: Pin Description 2 PIN NAME DESCRIPTION 1 VBATT Battery Voltage 2 RFIN RF Input 3 VMODE2 Mode Control Voltage 2 4 VMODE1 Mode Control Voltage 1 5 VEN 6 CPLOUT 7 GND Ground 8 CPLIN Coupler Input 9 RFOUT RF Output 10 VCC PA Enable Voltage Coupler Output Supply Voltage advanced product information - Rev 0.0 09/2013 VCC ALT5020 ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER MIN TYP MAX UNIT RF Input (PIN) - 0 10 dBm VCC 0 3.4 5 V VBATT 0 3.4 6 V Control Voltage (VENABLE, VMODE) 0 1.8 3.5 V Storage Temperature (TSTORAGE) -40 25 150 °C Functional operation to the specified performance is not implied under these conditions. Operation of any single parameter in excess of the absolute ratings may cause permanent damage. No damage occurs if one parameter is set at the limit while all other parameters are set within normal operating ranges. Table 3: Operating Ranges PARAMETER MIN TYP MAX UNIT Operating Frequency (f) 832 - 862 MHz COMMENTS UMTS Band 20 Supply Voltage (VCC) +0.6 +3.4 +4.4 V POUT < +27.7 dBm Battery Voltage (VBATT) +3.1 +3.4 +4.4 V POUT < +27.7 dBm Enable Voltage (VENABLE) +1.35 0 +1.8 0 +3.1 +0.5 V PA “on” PA “shut down” Mode Control Voltage (VMODE1) +1.35 0 +1.8 0 +3.1 +0.5 V Low Bias Mode High Bias Mode RF Output Power (POUT) (1, 2, 3) LTE, HPM LTE, LPM 26.9 - 27.7 16 - dBm Case Temperature (TC) -30 - +90 °C TS 36.101 Rel 8 for LTE The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: (1) For operation at Vcc = +3.1 V, Pout is derated by 0.8 dB. (2) For operation at 105 °C, POUT is derated by 1.0 dB. (3) LTE waveform characteristics up to 20 MHz QPSK, 18 RB’s. 3 advanced product information - Rev 0.0 09/2013 ALT5020 Table 4: Electrical Specifications - LTE Operation (RB = 12, START = 0, QPSK) (TC = +25 °C, VBATT = +3.4 V, VEN = +1.8 V, 50 Ω system, unless otherwise specified) PARAMETER MIN TYP MAX UNIT Gain 26.5 18 14 30 22 17 33 25 21 ACLR E-UTRA (1) at ± 10 MHz offset - -38 -38 -40 ACLR1 UTRA (1) at ± 7.5 MHz offset - ACLR2 UTRA (1) at ± 12.5 MHz offset COMMENTS POUT VCC VMODE1 VMODE2 dB +27.7 dBm +16 dBm +7 dBm 3.4 V 1.4 V 0.7 V 0V 1.8 V 1.8 V 0V 0V 1.8 V -34 -34 -34 dBc +27.7 dBm +16 dBm +7 dBm 3.4 V 1.4 V 0.7 V 0V 1.8 V 1.8 V 0V 0V 1.8 V -39 -39 -40 -36 -36 -36 dBc +27.7 dBm +16 dBm +7 dBm 3.4 V 1.4 V 0.7 V 0V 1.8 V 1.8 V 0V 0V 1.8 V - <-60 <-60 <-60 -40 -40 -40 dBc +27.7 dBm +16 dBm +7 dBm 3.4 V 1.4 V 0.7 V 0V 1.8 V 1.8 V 0V 0V 1.8 V 33 - 38 22 13 - % +27.7 dBm +16 dBm +7 dBm 3.4 V 1.4 V 0.7 V 0V 1.8 V 1.8 V 0V 0V 1.8 V Quiescent Current (Icq) Low Bias Mode - 25 - mA through VCC pin, VMODE1,2 = +1.8 V Mode Control Current - 0.05 0.1 mA through VMODE pin, VMODE1 = 1.8 V Enable Current - 0.05 0.1 mA through VENABLE pin BATT Current - 3 5.5 mA through VBATT pin, VMODE1 = +1.8 V Leakage Current - <5 10 µA VBATT = +4.4 V, VCC = +4.4 V VENABLE = 0 V, VMODE1 = 0 V Noise in Receive Band (2) - TBD - Harmonics 2fO 3fO, 4fO - TBD TBD - dBc Input Impedance - - 2:1 VSWR Coupling Factor - 20 - dB Directivity - 20 - dB Coupler IN-OUT Daisy Chain Insertion Loss - <0.25 - dB 698 to 2620 MHz Pin 8 to 6 Shutdown Mode POUT < +27.7 dBm In-band load VSWR < 5:1 Out-of-band load VSWR < 10:1 Applies over all operating conditions Efficiency (1) Spurious Output Level (all suprious outputs) Load mismatch stress with no permanent degradation or failure dBm/Hz 791 - 821 MHz - - <-65 dBc 8:1 - - VSWR POUT < +27.7 dBm Applies over full operating range Notes: (1) ACLR and Efficiency measured at 847 MHz. advanced product information - Rev 0.0 4 09/2013 ALT5020 APPLICATION INFORMATION To ensure proper performance, refer to all related Application Notes on the ANADIGICS web site: http://www.anadigics.com logic level (see Operating Ranges table) to VMODE1,2. The Bias Control table lists the recommended modes of operation for various applications. Shutdown Mode The power amplifier may be placed in a shutdown mode by applying logic low levels (see Operating Ranges table) to the VENABLE and VMODE voltages. Three operating modes are available to optimize current consumption. High Bias/High Power operating mode is for POUT levels > 15 dBm. At around 16 dBm output power, the PA should be “Mode Switched” to Medium power mode for lowest quiescent current consumption. The PA should be switched to Low Bias/ Low Power mode at ~<7 dbm. Bias Modes The power amplifier may be placed in either a Low, Medium or High Bias mode by applying the appropriate Vcontrols Venable/Vmode(s) On Sequence Start T_0N = 0µ Rise/Fall Max 1µS Defined at 10% to 90% of Min/Max Voltage Off Sequence Start T_0FF = 0µ ON Sequence OFF Sequence RFIN notes 1,2 VEN VCC note 1 T_0N+1µS T_0N+3µS Referenced After 90% of Rise Time T_0FF+2µS T_0FF+3µS Referenced Before10% of Fall Time Figure 3: Recommended ON/OFF Timing Sequence Notes: (1) Level might be changed after RF is ON. (2) RF OFF defined as PIN ≤ -30 dBm. (3) Switching simultaneously between VMODE and VEN is not recommended. 5 advanced product information - Rev 0.0 09/2013 ALT5020 Table 5: Bias Control POUT LEVELS BIAS MODE VENABLE VMODE1 VMODE2 VCC VBATT High power (High Bias Mode) > +16 dBm High +1.8 V 0V 0V 0.6 - 4.4 V 3.1 - 4.4 V Med power (Med Bias Mode) ≤ +17 dBm Medium +1.8 V +1.8 V 0V 0.6 - 4.4 V 3.1 - 4.4 V Low power (Low Bias Mode) ≤ +8 dBm Low +1.8 V +1.8 V +1.8 V 0.6 - 4.4 V 3.1 - 4.4 V - Shutdown 0V 0V 0V 0.6 - 4.4 V 3.1 - 4.4 V APPLICATION Shutdown VBATT VCC C2 2.2 µF C1 33pF GND at slug 1 2 RFIN VMODE2 VMODE1 VEN VBATT VCC RFIN RFOUT 10 9 3 VMODE2 N/C 8 4 VMODE1 GND 7 5 VEN N/C 6 Figure 4: Evaluation Board Schematic 6 advanced product information - Rev 0.0 09/2013 C3 0.1µF C4 2.2µF ceramic RFOUT ALT5020 PACKAGE OUTLINE Figure 5: Package Outline - 10 Pin 3 mm x 3 mm x 0.94 mm Surface Mount Module Pin 1 Identifier Date Code YY=Year; WW=Work week 5020 Part Number LLLLNN YYWWCC Lot Number Country Code (CC) Figure 6: Branding Specification 7 advanced product information - Rev 0.0 09/2013 ALT5020 PCB AND STENCIL DESIGN GUIDELINE Figure 7: Recommended PCB Layout Information 8 advanced product information - Rev 0.0 09/2013 ALT5020 COMPONENT PACKAGING Pin 1 Figure 8: Carrier Tape Figure 9: Reel 9 advanced product information - Rev 0.0 09/2013 ALT5020 ORDERING INFORMATION ORDER NUMBER TEMPERATURE RANGE PACKAGE DESCRIPTION ALT5020Q7 -30 oC to +90 oC RoHS Compliant 10 Pin 3 mm x 3 mm x 0.94 mm Tape and Reel, 2500 pieces per Reel Surface Mount Module ALT5020P9 -30 oC to +90 oC RoHS Compliant 10 Pin 3 mm x 3 mm x 0.94 mm Partial Tape and Reel Surface Mount Module COMPONENT PACKAGING ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. warning ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 10 advanced product information - Rev 0.0 09/2013