Sample &
Buy
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
LMZ23610
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
LMZ23610 10-A SIMPLE SWITCHER® Power Module With 36-V Maximum Input Voltage
and Current Sharing
1 Features
2 Applications
•
•
•
•
1
•
•
•
•
•
•
•
•
•
Integrated Shielded Inductor
Simple PCB Layout
Frequency Synchronization Input (350 kHz to 600
kHz)
Current Sharing Capability
Flexible Startup Sequencing Using External Softstart, Tracking and Precision Enable
Protection Against Inrush Currents and Faults
Such as Input UVLO and Output Short Circuit
Junction Temperature Range –40°C to 125°C
Single Exposed Pad and Standard Pinout for Easy
Mounting and Manufacturing
Fully Enabled for WEBENCH® Power Designer
Pin Compatible With LMZ22010/08,
LMZ12010/08, LMZ23608/06H, and
LMZ13610/08/06H
Performance Benefits
– High Efficiency Reduces System Heat
Generation
– Low Radiated Emissions (EMI) Tested to
EN55022 Class B Standard
– Only 7 External Components
– Low Output Voltage Ripple
– No External Heat Sink Required
– Simple Current Sharing for Higher Current
Applications
Electrical Specifications
– 50-W Maximum Total Output Power
– Up to 10-A Output Current
– Input Voltage Range 6 V to 36 V
– Output Voltage Range 0.8 V to 6 V
– Efficiency up to 92%
•
•
•
Point-of-load Conversions from 12-V and 24-V
Input Rail
Time-Critical Projects
Space Constrained / High Thermal Requirement
Applications
Negative Output Voltage Applications
(See AN-2027, SNVA425)
3 Description
The LMZ23610 SIMPLE SWITCHER® power module
is an easy-to-use step-down DC-DC solution capable
of driving up to 10-A load. The LMZ23610 is available
in an innovative package that enhances thermal
performance and allows for hand or machine
soldering.
The LMZ23610 can accept an input voltage rail
between 6 V and 36 V and can deliver an adjustable
and highly accurate output voltage as low as 0.8 V.
The LMZ23610 only requires two external resistors
and three external capacitors to complete the power
solution.
The LMZ23610 is a reliable and robust design with
the following protection features: thermal shutdown,
input undervoltage lockout, output overvoltage
protection, short circuit protection, output current limit,
and the device allows start-up into a prebiased
output. The sync input allows synchronization over
the 350- to 600-kHz switching frequency range.
Device Information(1)(2)
PART NUMBER
LMZ23610
PACKAGE
NDY (11)
BODY SIZE (NOM)
15.00 mm × 15.00 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
(2) Peak reflow temperature equals 245°C. See SNAA214 for
more details.
NOTE: EN 55022:2006, +A1:2007, FCC Part 15 Subpart B,
Tested on Evaluation Board with EMI Configuration
Simplified Application Schematic
Efficiency 3.3-V Output at 25°C
100
EFFICIENCY (%)
SH
VOUT
SS
FB
AGND
90
PGND
EN
SYNC
VIN
VIN
LMZ23610
VOUT
Share
Clock
CFF 4.7 nF (OPT)
Enable
RFBT
3 x 10 PF
CSS
0.47 PF
(OPT)
RFBB
See Table
70
6 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36Vin
60
50
See Table
CIN
80
COUT
2 x 330 PF
40
0
1
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
9 10
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LMZ23610
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
6.5
6.6
4
4
4
4
5
6
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
Detailed Description ............................................ 14
7.1
7.2
7.3
7.4
Overview .................................................................
Functional Block Diagram .......................................
Feature Description.................................................
Device Functional Modes........................................
14
14
14
17
8
Application and Implementation ........................ 19
8.1 Application Information............................................ 19
8.2 Typical Application ................................................. 19
9 Power Supply Recommendations...................... 25
10 Layout................................................................... 25
10.1
10.2
10.3
10.4
Layout Guidelines .................................................
Layout Examples...................................................
Power Dissipation and Thermal Considerations ...
Power Module SMT Guidelines ............................
25
26
28
28
11 Device and Documentation Support ................. 30
11.1
11.2
11.3
11.4
11.5
11.6
Device Support......................................................
Documentation Support ........................................
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
30
30
30
30
30
30
12 Mechanical, Packaging, and Orderable
Information ........................................................... 31
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision E (October 2013) to Revision F
Page
•
Removed Easy-To-Use PFM 7-Pin Package image ............................................................................................................. 1
•
Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional
Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device
and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1
Changes from Revision D (December 2012) to Revision E
Page
•
Deleted 12 mil......................................................................................................................................................................... 4
•
Changed 12 mil .................................................................................................................................................................... 28
•
Added Power Module SMT Guidelines................................................................................................................................. 28
2
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
LMZ23610
www.ti.com
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
5 Pin Configuration and Functions
NDY Package
11-Pin
Top View
11
10
9
8
7
6
5
4
3
2
1
PGND/EP
Connect to AGND
VOUT
VOUT
SH
SS
FB
AGND
AGND
EN
SYNC
VIN
VIN
Pin Functions
PIN
TYPE
DESCRIPTION
NAME
NO.
AGND
4
Ground
Analog Ground — Reference point for all stated voltages. Must be externally connected to
EP/PGND.
EN
3
Analog
Enable — Input to the precision enable comparator. Rising threshold is 1.274 V typical. Once
the module is enabled, a 20-µA source current is internally activated to accommodate
programmable hysteresis.
FB
5
Analog
Feedback — Internally connected to the regulation, overvoltage, and short circuit
comparators. The regulation reference point is 0.8 V at this input pin. Connect the feedback
resistor divider between the output and AGND to set the output voltage.
PGND
9
Ground
Exposed Pad / Power Ground Electrical path for the power circuits within the module. —
NOT Internally connected to AGND / pin 5. Used to dissipate heat from the package during
operation. Must be electrically connected to pin 5 external to the package.
SS
6
Analog
Soft-Start/Track input — To extend the 1.6-ms internal soft-start connect an external softstart capacitor. For tracking connect to an external resistive divider connected to a higher
priority supply rail. See Design Steps for the LMZ23610 Application section.
SH
7
Analog
Share pin. Connect this to the share pin of other LMZ23610 modules to share the load
between the devices. One device must be configured as the master by connecting the FB
normally. All other devices must be configured as slaves by leaving their respective FB pins
floating. Leave this pin floating if not used, do not ground. See Design Steps for the
LMZ23610 Application section.
SYNC
2
Analog
Sync Input — Apply a CMOS logic level square wave whose frequency is between 350 kHz
and 600 kHz to synchronize the PWM operating frequency to an external frequency source.
When not using synchronization this pin must be tied to ground. The module free-running
PWM frequency is 350 kHz.
VIN
1
Power
Supply input — Nominal operating range is 6 V to 36 V. A small amount of internal
capacitance is contained within the package assembly. Additional external input capacitance
is required between this pin and PGND.
VOUT
8
Power
Output Voltage — Output from the internal inductor. Connect the output capacitor between
this pin and PGND.
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
3
LMZ23610
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)
(1) (2)
MIN
MAX
UNIT
VIN to PGND
–0.3
40
V
EN, SYNC to AGND
–0.3
5.5
V
SS, FB, SH to AGND
–0.3
2.5
V
AGND to PGND
–0.3
0.3
V
150
°C
150
°C
Junction temperature
Storage temperature, Tstg
(1)
(2)
–65
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
For soldering specifications: see product folder at www.ti.com and lSNOA549
6.2 ESD Ratings
V(ESD)
(1)
Electrostatic discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
VALUE
UNIT
±2000
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
VIN
EN, SYNC
Operation Junction Temperature
MIN
MAX
6
36
UNIT
V
0
5
V
−40
125
°C
6.4 Thermal Information
LMZ23610
THERMAL METRIC (1)
NDY
UNIT
11 PINS
RθJA
Junction-to-ambient thermal
resistance (2)
RθJC(top)
(1)
(2)
4
Natural Convection
9.9
225 LFPM
6.8
500 LFPM
5.2
Junction-to-case (top) thermal resistance
1.0
°C/W
°C/W
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
RθJA measured on a 3.0-in × 3.5-in 4-layer board, with 2-oz. copper on outer layers and 1-oz. copper on inner layers, two hundred and
ten thermal vias, and 2-W power dissipation. Refer to evaluation board application note layout diagrams.
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
LMZ23610
www.ti.com
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
6.5 Electrical Characteristics
Limits are for TJ = 25°C unless otherwise specified. Minimum and Maximum limits are specified through test, design or
statistical correlation. Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for reference
purposes only. Unless otherwise stated the following conditions apply: VIN = 12V, VOUT = 3.3V
PARAMETER
TEST CONDITIONS
MIN (1)
TYP (2)
MAX (1)
UNIT
SYSTEM PARAMETERS
ENABLE CONTROL
1.274
VEN
EN threshold
VEN rising
IEN-HYS
EN hysteresis source current
VEN > 1.274 V
ISS
SS source current
VSS = 0 V
tSS
Internal soft-start interval
over the junction temperature (TJ)
range of –40°C to +125°C
1.096
1.452
13
V
µA
SOFT-START
50
over the junction temperature (TJ)
range of –40°C to +125°C
40
60
1.6
µA
ms
CURRENT LIMIT
ICL
Current limit threshold
DC average
12.5
A
INTERNAL SWITCHING OSCILLATOR
fosc
Free-running oscillator
frequency
Sync input connected to ground
314
fsync
Synchronization range
Vsync = 3.3 Vp-p
314
VIL-sync
Synchronization logic zero
amplitude
Relative to AGND
over the junction temperature (TJ)
range of –40°C to +125°C
VIH-sync
Synchronization logic one
amplitude
Relative to AGND
over the junction temperature (TJ)
range of –40°C to +125°C
Sync d.c.
Synchronization duty cycle
range
359
404
kHz
600
kHz
0.4
V
1.8
15%
V
50%
85%
REGULATION AND OVERVOLTAGE COMPARATOR
0.795
VSS >+ 0.8 V
IO = 10 A
VFB
In-regulation feedback voltage
VFB-OV
Feedback over-voltage
protection threshold
IFB
Feedback input bias current
IQ
Non-switching quiescent
current
SYNC = 3.0 V
ISD
Shutdown quiescent current
VEN = 0 V
Dmax
Maximum duty factor
over the junction temperature (TJ)
range of –40°C to +125°C
0.775
0.815
V
0.86
V
5
nA
3
mA
32
μA
85%
THERMAL CHARACTERISTICS
TSD
Thermal shutdown
Rising
165
°C
TSD-HYST
Thermal shutdown hysteresis
Falling
15
°C
24
mVPP
PERFORMANCE PARAMETERS (3)
ΔVO
Output voltage ripple
BW at 20 MHz
ΔVO/ΔVIN
Line regulation
VIN = 12 V to 20 V, IOUT= 10 A
ΔVO/ΔIOUT
Load regulation
VIN = 12 V, IOUT= 0.001 A to 10 A
η
Peak efficiency
VIN = 12 V, VOUT = 3.3 V, IOUT = 5 A
89.5%
η
Full load efficiency
VIN = 12 V, VOUT = 3.3 V, IOUT = 10 A
87.5%
(1)
(2)
(3)
±0.2%
1
mV/A
Minimum and Maximum limits are 100% production tested at 25°C. Limits over the operating temperature range are specified through
correlation using Statistical Quality Control (SQC) methods. Limits are used to calculate TI’s Average Outgoing Quality Level (AOQL).
Typical numbers are at 25°C and represent the most likely parametric norm.
Refer to BOM in Table 1.
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
5
LMZ23610
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
www.ti.com
6.6 Typical Characteristics
100
12
90
10
DISSIPATION (W)
EFFICIENCY (%)
Unless otherwise specified, the following conditions apply: VIN = 12 V; CIN = three × 10 μF + 47-nF X7R Ceramic; COUT = two
× 330-μF Specialty Polymer + 47-µF Ceramic + 47-nF Ceramic; CFF = 4.7 nF; TA = 25° C for waveforms. All indicated
temperatures are ambient.
80
70
8 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36Vin
60
50
40
1
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
4
9 10
0
12
90
10
80
70
6 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36Vin
60
50
40
1
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
9 10
Figure 2. Dissipation 5-V Output at 25°C
100
DISSIPATION (W)
EFFICIENCY (%)
6
2
Figure 1. Efficiency 5-V Output at 25°C
6 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36 Vin
8
6
4
2
0
0
1
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
9 10
Figure 3. Efficiency 3.3-V Output at 25°C
0
12
90
10
80
70
6 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36Vin
60
50
40
1
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
9 10
Figure 4. Dissipation 3.3-V Output at 25°C
100
DISSIPATION (W)
EFFICIENCY (%)
8
0
0
6 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36 Vin
8
6
4
2
0
0
1
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
9 10
Figure 5. Efficiency 2.5-V Output at 25°C
6
8 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36 Vin
0
1
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
9 10
Figure 6. Dissipation 2.5-V Output at 25°C
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
LMZ23610
www.ti.com
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
Typical Characteristics (continued)
90
12
80
10
DISSIPATION (W)
EFFICIENCY (%)
Unless otherwise specified, the following conditions apply: VIN = 12 V; CIN = three × 10 μF + 47-nF X7R Ceramic; COUT = two
× 330-μF Specialty Polymer + 47-µF Ceramic + 47-nF Ceramic; CFF = 4.7 nF; TA = 25° C for waveforms. All indicated
temperatures are ambient.
70
60
50
6 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36Vin
40
30
20
6
4
2
1
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
9 10
Figure 7. Efficiency 1.8-V Output at 25°C
0
12
80
10
70
60
50
6 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36Vin
40
30
20
1
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
9 10
Figure 8. Dissipation 1.8-V Output at 25°C
90
DISSIPATION (W)
EFFICIENCY (%)
8
0
0
6 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36 Vin
8
6
4
2
0
0
1
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
9 10
Figure 9. Efficiency 1.5-V Output at 25°C
0
12
80
DISSIPATION (W)
60
50
6 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36Vin
40
30
20
10
0
1
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
9 10
6 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36 Vin
10
70
1
Figure 10. Dissipation 1.5-V Output at 25°C
90
EFFICIENCY (%)
6 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36 Vin
8
6
4
2
0
9 10
Figure 11. Efficiency 1.2-V Output at 25°C
0
1
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
9 10
Figure 12. Dissipation 1.2-V Output at 25°C
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
7
LMZ23610
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
www.ti.com
Typical Characteristics (continued)
Unless otherwise specified, the following conditions apply: VIN = 12 V; CIN = three × 10 μF + 47-nF X7R Ceramic; COUT = two
× 330-μF Specialty Polymer + 47-µF Ceramic + 47-nF Ceramic; CFF = 4.7 nF; TA = 25° C for waveforms. All indicated
temperatures are ambient.
12
90
6 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36 Vin
80
10
DISSIPATION (W)
EFFICIENCY (%)
70
60
50
40
6 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36Vin
30
20
10
0
0
1
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
0
9 10
0
12
90
10
80
70
8 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36Vin
60
40
1
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
9 10
Figure 14. Dissipation 1-V Output at 25°C
DISSIPATION (W)
EFFICIENCY (%)
4
100
50
8 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36 Vin
8
6
4
2
0
0
1
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
9 10
Figure 15. Efficiency 5-V Output at 85°C
0
12
90
DISSIPATION (W)
70
60
6 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36Vin
50
40
30
20
0
1
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
9 10
6 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36 Vin
10
80
1
Figure 16. Dissipation 5-V Output at 85°C
100
EFFICIENCY (%)
6
2
Figure 13. Efficiency 1-V Output at 25°C
8
6
4
2
0
9 10
Figure 17. Efficiency 3.3-V Output at 85°C
8
8
0
1
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
9 10
Figure 18. Dissipation 3.3-V Output at 85°C
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
LMZ23610
www.ti.com
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
Typical Characteristics (continued)
Unless otherwise specified, the following conditions apply: VIN = 12 V; CIN = three × 10 μF + 47-nF X7R Ceramic; COUT = two
× 330-μF Specialty Polymer + 47-µF Ceramic + 47-nF Ceramic; CFF = 4.7 nF; TA = 25° C for waveforms. All indicated
temperatures are ambient.
100
12
70
60
6 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36Vin
50
40
30
20
0
1
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
6
4
0
9 10
0
14
80
12
70
60
50
6 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36Vin
40
30
20
10
0
1
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
8
6
4
0
9 10
0
14
12
DISSIPATION (W)
70
60
50
6 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36Vin
10
0
1
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
1
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
9 10
Figure 22. Dissipation 1.8-V Output at 85°C
80
20
9 10
6 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36 Vin
10
90
30
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
2
Figure 21. Efficiency 1.8-V Output at 85°C
40
1
Figure 20. Dissipation 2.5-V Output at 85°C
90
DISSIPATION (W)
EFFICIENCY (%)
8
2
Figure 19. Efficiency 2.5-V Output at 85°C
EFFICIENCY (%)
6 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36 Vin
10
80
DISSIPATION (W)
EFFICIENCY (%)
90
6 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36 Vin
10
8
6
4
2
0
9 10
Figure 23. Efficiency 1.5-V Output at 85°C
0
1
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
9 10
Figure 24. Dissipation 1.5-V Output at 85°C
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
9
LMZ23610
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
www.ti.com
Typical Characteristics (continued)
Unless otherwise specified, the following conditions apply: VIN = 12 V; CIN = three × 10 μF + 47-nF X7R Ceramic; COUT = two
× 330-μF Specialty Polymer + 47-µF Ceramic + 47-nF Ceramic; CFF = 4.7 nF; TA = 25° C for waveforms. All indicated
temperatures are ambient.
90
14
80
12
DISSIPATION (W)
EFFICIENCY (%)
70
60
50
6 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36Vin
40
30
20
10
0
1
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
6 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36 Vin
10
8
6
4
2
0
9 10
0
90
14
6 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36 Vin
12
DISSIPATION (W)
EFFICIENCY (%)
9 10
Figure 26. Dissipation 1.2-V Output at 85°C
70
60
50
40
6 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
30 Vin
36Vin
30
20
10
0
0
1
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
10
8
6
4
2
0
9 10
0
Figure 27. Efficiency 1-V Output at 85°C
1
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
9 10
Figure 28. Dissipation 1-V Output at 85°C
1.002
12
MAXIMUM OUTPUT CURRENT (A)
NORMALIZED VOUT (V/V)
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
Figure 25. Efficiency 1.2-V Output at 85°C
80
1.001
1.000
6 Vin
8 Vin
10 Vin
12 Vin
16 Vin
20 Vin
24 Vin
36 Vin
0.999
0.998
0
1
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
10
8
6
4
2
0
9 10
VOUT = 3.3 V
VIN
JA = 9.9 °C/W
JA = 6.8 °C/W
JA = 5.2 °C/W
20 30 40 50 60 70 80 90 100 110 120
TEMPERATURE (C)
= 24 V, VOUT = 5 V
Figure 29. Normalized Line and Load Regulation
10
1
Submit Documentation Feedback
Figure 30. Thermal Derating
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
LMZ23610
www.ti.com
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
Typical Characteristics (continued)
Unless otherwise specified, the following conditions apply: VIN = 12 V; CIN = three × 10 μF + 47-nF X7R Ceramic; COUT = two
× 330-μF Specialty Polymer + 47-µF Ceramic + 47-nF Ceramic; CFF = 4.7 nF; TA = 25° C for waveforms. All indicated
temperatures are ambient.
30
10
24
8
6
4
21
18
15
12
9
2
0
VIN
2 Layer 0 LFPM
2 Layer 225 LFPM
4 Layer 0 LFPM
4 Layer 225 LFPM
27
THETA JA (°C/W)
MAXIMUM OUTPUT CURRENT (A)
12
JA = 9.9 °C/W
JA = 6.8 °C/W
JA = 5.2 °C/W
6
3
0
20 30 40 50 60 70 80 90 100 110 120
TEMPERATURE (C)
= 24 V, VOUT = 3.3 V
Figure 31. Thermal Derating
12 VIN, 5 VOUT at Full Load, BW = 20 MHz
4
6
8
2
COPPER AREA (in )
10
12
Figure 32. RJθA vs Copper Heat Sinking Area
12 VIN, 5 VOUT at Full Load, BW = 250 MHz
Figure 33. Output Ripple
12 VIN, 3.3 VOUT at Full Load, BW = 20 MHz
2
Figure 34. Output Ripple
12 VIN, 3.3 VOUT at Full Load, BW = 250 MHz
Figure 36. Output Ripple
Figure 35. Output Ripple
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
11
LMZ23610
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
www.ti.com
Typical Characteristics (continued)
Unless otherwise specified, the following conditions apply: VIN = 12 V; CIN = three × 10 μF + 47-nF X7R Ceramic; COUT = two
× 330-μF Specialty Polymer + 47-µF Ceramic + 47-nF Ceramic; CFF = 4.7 nF; TA = 25° C for waveforms. All indicated
temperatures are ambient.
12 VIN, 1.2 VOUT at Full Load, BW = 250 MHz
12 VIN, 1.2 VOUT at Full Load, BW = 20 MHz
Figure 38. Output Ripple
Figure 37. Output Ripple
12 VIN, 5 VOUT, 1- to 10-A Step
12 VIN, 3.3 VOUT, 1- to 10-A Step
Figure 39. Transient Response
Figure 40. Transient Response
16
14
CURRENT (A)
12
10
8
6
4
Output Current
Input Current
2
0
5
10
15
INPUT VOLTAGE (V)
20
12 VIN, 1.2 VOUT, 1- to 10-A Step
Figure 41. Transient Response
12
Figure 42. Short Circuit Current vs Input Voltage
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
LMZ23610
www.ti.com
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
Typical Characteristics (continued)
Unless otherwise specified, the following conditions apply: VIN = 12 V; CIN = three × 10 μF + 47-nF X7R Ceramic; COUT = two
× 330-μF Specialty Polymer + 47-µF Ceramic + 47-nF Ceramic; CFF = 4.7 nF; TA = 25° C for waveforms. All indicated
temperatures are ambient.
No CSS
CSS = 0.47 µF
Figure 43. 3.3 VOUT Soft-Start
Figure 44. 3.3 VOUT Soft-Start
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
13
LMZ23610
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
www.ti.com
7 Detailed Description
7.1 Overview
The architecture used is an internally compensated emulated peak current mode control, based on a monolithic
synchronous SIMPLE SWITCHER core capable of supporting high load currents. The output voltage is
maintained through feedback compared with an internal 0.8-V reference. For emulated peak current-mode, the
valley current is sampled on the down-slope of the inductor current. This is used as the DC value of current to
start the next cycle.
The primary application for emulated peak current-mode is high input voltage to low output voltage operating at a
narrow duty cycle. By sampling the inductor current at the end of the switching cycle and adding an external
ramp, the minimum ON-time can be significantly reduced, without the need for blanking or filtering which is
normally required for peak current-mode control.
7.2 Functional Block Diagram
Linear
Regulator
2M
VIN
1
3
3
CIN
EN
2
350 kHz
PWM
SS
2.2 uH VOUT
VREF
3
RFBT
CINint
1
SYNC
CSS
CBST
COUT
FB
RFBB
2
Comp
SH
Filter
AGND
Regulator IC
EP/
PGND
Internal Passives
7.3 Feature Description
7.3.1 Synchronization Input
The PWM switching frequency can be synchronized to an external frequency source. The PWM switching will be
in phase with the external frequency source. If this feature is not used, connect this input either directly to
ground, or connect to ground through a resistor of 1.5 kΩ or less. The allowed synchronization frequency range
is 314 kHz to 600 kHz. The typical input threshold is 1.4 V. Ideally, the input clock must overdrive the threshold
by a factor of 2, so direct drive from 3.3-V logic through a 1.5-kΩ or less Thevenin source resistance is
recommended. Note that applying a sustained logic 1 corresponds to 0-Hz PWM frequency and will cause the
module to stop switching.
7.3.2 Current Sharing
When a load current higher than 10 A is required by the application, the LMZ23610 can be configured to share
the load between multiple devices. To share the load current between the devices, connect the SH pin of all
current sharing LMZ23610 modules. One device must be configured as the master by connecting FB normally.
All other devices must be configured as slaves by leaving their respective FB pins floating. The modules must be
synchronized by a clock signal to avoid beat frequencies in the output voltage caused by small differences in the
internal 359-kHz clock. If the modules are not synchronized, the magnitude of the ripple voltage will depend on
the phase relationship of the internal clocks. The external synchronizing clocks can be in phase for all modules,
14
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
LMZ23610
www.ti.com
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
Feature Description (continued)
or out of phase to reduce the current stress on the input and output capacitors. As an example, two modules can
be run 180 degrees out of phase, and three modules can be run 120 degrees out of phase. The VIN, VOUT,
PGND, and AGND pins must also be connected with low impedance paths. It is particularly important to pay
close attention to the layout of AGND and SH, as offsets in grounding or noise picked up from other devices will
be seen as a mismatch in current sharing and could cause noise issues.
Current sharing modules can be configured to share the same set of bulk input and output capacitors, while each
having their own local input and output bypass capacitors. A CIN_BYP >= 30 µF is still recommended for each
module that is connected in a current sharing configuration. A COUT_BYP consisting of 47-nF X7R ceramic
capacitor in parallel with a 22-µF ceramic capacitor is recommended to locally bypass the output voltage for each
module. These capacitors will provide local bypassing of high-frequency switched currents.
In a current sharing system using two or more modules, the slaves have their error amp circuitry disconnected.
The master overrides the error amplifier outputs of the slaves. This signal is then compared to each module’s
individual current sense circuitry. Due to this, the current sense gain of the entire system increases according to
the number of modules slaved to the master. To compensate for this and ensure good stability, the total output
capacitance has to be increased. For example, two modules configured to provide 1.2 VOUT and 20 amps have a
required total bulk output capacitance of COUT_BULK = 2 × 450-µF (ESR 25 mΩ). This is a thirty six percent
increase in the required output capacitance of a stand alone module. Up to 6 modules can be connected in
parallel for loads up to 60 A. For more information on current sharing refer to AN-2093 (SNVA460).
VOUT
SH
SS
X X
Clk
CIN_BYP
FB
AGND
PGND
EN
SYNC
VIN
SLAVE
Share
COUT_BYP
Enable
VIN
VOUT
Clk
CIN_BYP
VOUT
SH
SS
FB
AGND
PGND
EN
VIN
CIN_BULK
SYNC
MASTER
COUT_BULK
LOAD
Share
CSS
Enable
COUT_BYP
RFBB
RFBT
Figure 45. Current Sharing Example Schematic
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
15
LMZ23610
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
www.ti.com
Feature Description (continued)
Figure 46. Output Voltage Ripple of Two Modules
With Synchronization Clocks in Phase
Figure 47. Output Voltage Ripple of Two Modules
With Synchronization Clocks 180 Degrees Out of Phase
7.3.3 Output Overvoltage Protection
If the voltage at FB is greater than a 0.86-V internal reference, the output of the error amplifier is pulled toward
ground, causing VOUT to fall.
7.3.4 Current Limit
The LMZ23610 is protected by both low-side (LS) and high-side (HS) current limit circuitry. The LS current limit
detection is carried out during the OFF-time by monitoring the current through the LS synchronous MOSFET.
Referring to the Functional Block Diagram, when the top MOSFET is turned off, the inductor current flows
through the load, the PGND pin and the internal synchronous MOSFET. If this current exceeds 13 A (typical), the
current limit comparator disables the start of the next switching period. Switching cycles are prohibited until
current drops below the limit.
NOTE
DC current limit is dependent on duty cycle as illustrated in the graph in the Typical
Characteristics section.
The HS current limit monitors the current of top side MOSFET. Once HS current limit is detected (16 A typical) ,
the HS MOSFET is shutoff immediately, until the next cycle. Exceeding HS current limit causes VOUT to fall.
Typical behavior of exceeding LS current limit is that fSW drops to 1/2 of the operating frequency.
7.3.5 Thermal Protection
The junction temperature of the LMZ23610 must not be allowed to exceed its maximum ratings. Thermal
protection is implemented by an internal Thermal Shutdown circuit which activates at 165°C (typical) causing the
device to enter a low power standby state. In this state the main MOSFET remains off causing VOUT to fall, and
additionally the CSS capacitor is discharged to ground. Thermal protection helps prevent catastrophic failures for
accidental device overheating. When the junction temperature falls back below 150 °C (typical hysteresis = 15°C)
the SS pin is released, VOUT rises smoothly, and normal operation resumes.
Applications requiring maximum output current especially those at high input voltage may require additional
derating at elevated temperatures.
7.3.6 Prebiased Start-Up
The LMZ23610 will properly start up into a prebiased output. This start-up situation is common in multiple rail
logic applications where current paths may exist between different power rails during the start-up sequence. The
following scope capture shows proper behavior in this mode. Trace one is Enable going high. Trace two is 1.8-V
prebias rising to 3.3 V. Trace three is the SS voltage with a CSS= 0.47 µF. Rise-time determined by CSS.
16
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
LMZ23610
www.ti.com
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
Feature Description (continued)
Figure 48. Prebiased Start-Up
7.3.6.1 Tracking Supply Divider Option
The tracking function allows the module to be connected as a slave supply to a primary voltage rail (often the
3.3-V system rail) where the slave module output voltage is lower than that of the master. Proper configuration
allows the slave rail to power up coincident with the master rail such that the voltage difference between the rails
during ramp-up is small (that is, < 0.15 V typical). The values for the tracking resistive divider must be selected
such that the effect of the internal 50-µA current source is minimized. In most cases the ratio of the tracking
divider resistors is the same as the ratio of the output voltage setting divider. Proper operation in tracking mode
dictates the soft-start time of the slave rail be shorter than the master rail; a condition that is easy to satisfy
because the CSS cap is replaced by RTKB. The tracking function is only supported for the power up interval of the
master supply; once the SS/TRK rises past 0.795 V the input is no longer enabled and the 50-µA internal current
source is switched off.
3.3V Master
2.5Vout
Int VCC
50 PA
Rtkt
226
Rfbt
2.26k
SS
FB
Rtkb
107
Rfbb
1.07k
Figure 49. Tracking Option Input Detail
7.4 Device Functional Modes
7.4.1 Discontinuous Conduction and Continuous Conduction Modes
At light load the regulator will operate in discontinuous conduction mode (DCM). With load currents above the
critical conduction point, it will operate in continuous conduction mode (CCM). When operating in DCM, inductor
current is maintained to an average value equaling IOUT. In DCM the low-side switch will turn off when the
inductor current falls to zero, this causes the inductor current to resonate. Although it is in DCM, the current is
allowed to go slightly negative to charge the bootstrap capacitor.
In CCM, current flows through the inductor through the entire switching cycle and never falls to zero during the
OFF-time.
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
17
LMZ23610
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
www.ti.com
Device Functional Modes (continued)
Figure 50 is a comparison pair of waveforms showing both the CCM (upper) and DCM operating modes.
VIN = 12 V, VO = 3.3 V, IO = 3 A / 0.3 A
Figure 50. CCM and DCM Operating Modes
18
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
LMZ23610
www.ti.com
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The LMZ23610 is a step-down DC-to-DC power module. It is typically used to convert a higher DC voltage to a
lower DC voltage with a maximum output current of 10 A. The following design procedure can be used to select
components for the LMZ23610. Alternately, the WEBENCH software may be used to generate complete designs.
When generating a design, the WEBENCH software uses iterative design procedure and accesses
comprehensive databases of components. Please go to www.ti.com for more details.
8.2 Typical Application
CIN6
(OPT)
Clk
+ CIN5
(OPT)
CIN2,3,4
CIN1
VOUT
Share
CSS
RSYNC
CO1
(OPT)
CO3,4
CO2
(OPT)
CO5
(OPT)
LOAD
RFBB
RENT
D1
5.1V
(OPT)
VOUT
SH
SS
FB
PGND
AGND
EN
VIN
SYNC
VIN
LMZ23610
RENB
RFBT
Figure 51. Typical Application Schematic Diagram
8.2.1 Design Requirements
For this example the following application parameters exist:
• VIN Range = Up to 36 V
• VOUT = 0.8 V to 6 V
• IOUT = 10 A
8.2.2 Detailed Design Procedure
8.2.2.1 Design Steps
The LMZ23610 is fully supported by WEBENCH which offers: component selection, electrical and thermal
simulations. Additionally, there are both evaluation and demonstration boards that may be used as a starting
point for design. The following list of steps can be used to manually design the LMZ23610 application.
All references to values refer to the Simplified Application Schematic.
1.
2.
3.
4.
5.
Select minimum operating VIN with enable divider resistors
Program VOUT with FB resistor divider selection
Select COUT
Select CIN
Determine module power dissipation
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
19
LMZ23610
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
www.ti.com
Typical Application (continued)
6. Layout PCB for required thermal performance
8.2.2.2 Enable Divider, RENT, RENB and RENHSelection
Internal to the module is a 2-MΩ pullup resistor connected from VIN to Enable. For applications not requiring
precision undervoltage lockout (UVLO), the Enable input may be left open circuit and the internal resistor will
always enable the module. In such case, the internal UVLO occurs typically at 4.3 V (VIN rising).
In applications with separate supervisory circuits Enable can be directly interfaced to a logic source. In the case
of sequencing supplies, the divider is connected to a rail that becomes active earlier in the power-up cycle than
the LMZ23610 output rail.
Enable provides a precise 1.274-V threshold to allow direct logic drive or connection to a voltage divider from a
higher enable voltage such as VIN. Additionally there is 13 μA (typical) of switched offset current allowing
programmable hysteresis. See Figure 52.
The function of the enable divider is to allow the designer to choose an input voltage below which the circuit will
be disabled. This implements the feature of a programmable UVLO. The two resistors must be chosen based on
the following ratio:
RENT / RENB = (VIN UVLO / 1.274 V) – 1
(1)
The LMZ23610 typical application shows 12.7 kΩ for RENB and 42.2 kΩ for RENT resulting in a rising UVLO of
5.51 V. Note that this divider presents 4.62 V to the EN input when VIN is raised to 20 V. This upper voltage must
always be checked, making sure that it never exceeds the Abs Max 5.5-V limit for Enable. A 5.1-V Zener clamp
can be applied in cases where the upper voltage would exceed the EN input's range of operation. The Zener
clamp is not required if the target application prohibits the maximum Enable input voltage from being exceeded.
Additional enable voltage hysteresis can be added with the inclusion of RENH. It is possible to select values for
RENT and RENB such that RENH is a value of zero allowing it to be omitted from the design.
Rising threshold can be calculated as follows:
VEN(rising) = 1.274 ( 1 + (RENT|| 2 meg)/ RENB)
(2)
Whereas the falling threshold level can be calculated using:
VEN(falling) = VEN(rising) – 13 µA ( RENT|| 2 meg || RENTB + RENH )
VIN
(3)
INT-VCC (5V)
13 PA
2.0M
RENT
42.2k
RENH
ENABLE
RUN
100:
5.1V
RENB
12.7k
1.274V
Figure 52. Enable Input Detail
8.2.2.3 Output Voltage Selection
Output voltage is determined by a divider of two resistors connected between VOUT and AGND. The midpoint of
the divider is connected to the FB input.
The regulated output voltage determined by the external divider resistors RFBT and RFBB is:
20
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
LMZ23610
www.ti.com
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
Typical Application (continued)
VOUT = 0.795 V × (1 + RFBT / RFBB)
(4)
Rearranging terms; the ratio of the feedback resistors for a desired output voltage is:
RFBT / RFBB = (VOUT / 0.795 V) – 1
(5)
These resistors must generally be chosen from values in the range of 1.0 kΩ to 10.0 kΩ.
For VOUT = 0.8 V the FB pin can be connected to the output directly and RFBB can be set to 8.06 kΩ to provide
minimum output load.
Table 1 lists the values for RFBT , and RFBB.
Table 1. Typical Application Bill of Materials
REF DES
DESCRIPTION
CASE SIZE
MANUFACTURER
MANUFACTURER P/N
U1
SIMPLE SWITCHER
PFM-11
Texas Instruments
LMZ23610TZ
CIN1,6 (OPT)
0.047 µF, 50 V, X7R
1206
Yageo America
CC1206KRX7R9BB473
CIN2,3,4
10 µF, 50 V, X7R
1210
Taiyo Yuden
UMK325BJ106MM-T
CIN5 (OPT)
CAP, AL, 150 µF, 50 V
Radial G
Panasonic
EEE-FK1H151P
CO1,5 (OPT)
0.047 µF, 50 V, X7R
1206
Yageo America
CC1206KRX7R9BB473
CO2 (OPT)
47 µF, 10 V, X7R
1210
Murata
GRM32ER61A476KE20L
CO3,4
330 μF, 6.3 V, 0.015 Ω
CAPSMT_6_UE
Kemet
T520D337M006ATE015
RFBT
3.32 kΩ
0805
Panasonic
ERJ-6ENF3321V
RFBB
1.07 kΩ
0805
Panasonic
ERJ-6ENF1071V
RSYNC
1.50 kΩ
0805
Vishay Dale
CRCW08051K50FKEA
RENT
42.2 kΩ
0805
Panasonic
ERJ-6ENF4222V
RENB
12.7 kΩ
0805
Panasonic
ERJ-6ENF1272V
CSS
0.47 μF, ±10%, X7R, 16 V
0805
AVX
0805YC474KAT2A
D1 (OPT)
5.1 V, 0.5 W
SOD-123
Diodes Inc.
MMSZ5231BS-7-F
8.2.2.4 Soft-Start Capacitor Selection
Programmable soft-start permits the regulator to slowly ramp to its steady-state operating point after being
enabled, thereby reducing current inrush from the input supply and slowing the output voltage rise-time.
Upon turnon, after all UVLO conditions have been passed, an internal 1.6-ms circuit slowly ramps the SS input to
implement internal soft-start. If 1.6 ms is an adequate turnon time then the Css capacitor can be left
unpopulated. Longer soft-start periods are achieved by adding an external capacitor to this input.
Soft-start duration is given by the formula:
tSS = VREF × CSS / Iss = 0.795 V × CSS / 50 µA
(6)
This equation can be rearranged as follows:
CSS = tSS × 50 μA / 0.795 V
(7)
Using a 0.22-μF capacitor results in 3.5-ms typical soft-start duration; and 0.47 μF results in 7.5 ms typical. 0.47
μF is a recommended initial value.
As the soft-start input exceeds 0.795 V the output of the power stage will be in regulation and the 50-μA current
is deactivated. The following conditions will reset the soft-start capacitor by discharging the SS input to ground
with an internal current sink.
•
•
•
The Enable input being pulled low
A thermal shutdown condition
VIN falling below 4.3 V (typical) and triggering the VCC UVLO
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
21
LMZ23610
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
www.ti.com
8.2.2.5 COUT Selection
None of the required COUT output capacitance is contained within the module. A minimum value ranging from 330
μF for 6-VOUT to 660 μF for 1.2-VOUT applications is required based on the values of internal compensation in the
error amplifier. These minimum values can be decreased if the effective capacitor ESR is higher than 15 mΩ.
A Low ESR (15 mΩ) tantalum, organic semiconductor or specialty polymer capacitor types in parallel with a 47nF X7R ceramic capacitor for high frequency noise reduction is recommended for obtaining lowest ripple. The
output capacitor COUT may consist of several capacitors in parallel placed in close proximity to the module. The
output voltage ripple of the module depends on the equivalent series resistance (ESR) of the capacitor bank, and
can be calculated by multiplying the ripple current of the module by the effective impedance of your chosen
output capacitors (for ripple current calculation, see Equation 14). Electrolytic capacitors will have large ESR and
lead to larger output ripple than ceramic or polymer types. For this reason a combination of ceramic and polymer
capacitors is recommended for low output ripple performance.
The output capacitor assembly must also meet the worst case ripple current rating of ΔiL, as calculated in
Equation 14 below. Loop response verification is also valuable to confirm closed loop behavior.
For applications with dynamic load steps; the following equation provides a good first pass approximation of COUT
for load transient requirements.
Istep
COUTt
('VOUT - ISTEP x ESR) x (
fSW
)
VOUT
(8)
For 12 VIN, 3.3 VOUT, a transient voltage of 5% of VOUT = 0.165 V (ΔVOUT), a 9-A load step (ISTEP), an output
capacitor effective ESR of 3 mΩ, and a switching frequency of 350 kHz (fSW):
9A
COUTt
(0.165V - 9A x 0.003) x (
350e3
)
3.3V
t615 PF
(9)
NOTE
The stability requirement for minimum output capacitance must always be met.
One recommended output capacitor combination is two 330-μF, 15-mΩ ESR tantalum polymer capacitors
connected in parallel with a 47-µF 6.3-V X5R ceramic. This combination provides excellent performance that may
exceed the requirements of certain applications. Additionally some small 47-nF ceramic capacitors can be used
for high-frequency EMI suppression.
8.2.2.6 CIN Selection
The LMZ23610 module contains two internal ceramic input capacitors. Additional input capacitance is required
external to the module to handle the input ripple current of the application. The input capacitor can be several
capacitors in parallel. This input capacitance must be located in very close proximity to the module. Input
capacitor selection is generally directed to satisfy the input ripple current requirements rather than by
capacitance value. Input ripple current rating is dictated by the equation:
ICIN-RMS = IOUT x D(1-D)
where
•
D ≊ VOUT / VIN
(10)
As a point of reference, the worst case ripple current will occur when the module is presented with full load
current and when VIN = 2 × VOUT.
Recommended minimum input capacitance is 30-µF X7R (or X5R) ceramic with a voltage rating at least 25%
higher than the maximum applied input voltage for the application. TI also recommends to pay attention to the
voltage and temperature derating of the capacitor selected.
NOTE
Ripple current rating of ceramic capacitors may be missing from the capacitor data sheet
and you may have to contact the capacitor manufacturer for this parameter.
22
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
LMZ23610
www.ti.com
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
If the system design requires a certain minimum value of peak-to-peak input ripple voltage (ΔVIN) to be
maintained then the following equation may be used.
CIN 8
IOUT x D x (1 - D)
fSW x 'VIN
(11)
If ΔVIN is 200 mV or 1.66% of VIN for a 12-V input to 3.3-V output application and fSW = 350 kHz then:
10A x §
3.3V · § 3.3V·
x 1© 12V ¹ © 12V ¹
CIN 8
350 kHz x 200mV
8 28µF
(12)
Additional bulk capacitance with higher ESR may be required to damp any resonant effects of the input
capacitance and parasitic inductance of the incoming supply lines. The LMZ23610 typical applications schematic
and evaluation board include a 150-μF 50-V aluminum capacitor for this function. There are many situations
where this capacitor is not necessary.
8.2.2.7 Discontinuous Conduction and Continuous Conduction Mode Selection
The approximate formula for determining the DCM/CCM boundary is as follows:
(VIN - VOUT) x D
IDCB =
2 x L x fSW
(13)
The inductor internal to the module is 2.2 μH. This value was chosen as a good balance between low and high
input voltage applications. The main parameter affected by the inductor is the amplitude of the inductor ripple
current (ΔiL). ΔiL can be calculated with:
(VIN - VOUT) x D
'iL =
L x fSW
where
•
•
VIN is the maximum input voltage
fSW is typically 359 kHz
(14)
If the output current IOUT is determined by assuming that IOUT = IL, the higher and lower peak of ΔiL can be
determined.
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
23
LMZ23610
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
www.ti.com
8.2.3 Application Curves
100
MAXIMUM OUTPUT CURRENT (A)
12
EFFICIENCY (%)
90
80
70
60
50
40
30
24 Vin
20
0
1
2 3 4 5 6 7 8
OUTPUT CURRENT (A)
10
8
6
4
2
JA = 9.9 °C/W
JA = 6.8 °C/W
JA = 5.2 °C/W
0
9 10
VIN = 24 V, VOUT = 3.3 V
20
40
60
80
100
TEMPERATURE (C)
120
VIN = 24 V, VOUT = 3.3 V
Figure 54. Thermal Derating Curve
Figure 53. Efficiency
AMPLITUDE (dBV/m)
50
40
30
20
10
0
Horizontal Peak
Vertical Peak
Class B Limit
Class A Limit
0 100 200 300 400 500 600 700 800 9001000
FREQUENCY (MHz)
VIN = 24 V, VOUT = 5 V,
IOUT = 10 A
Figure 55. Radiated EMI (EN 55022)
24
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
LMZ23610
www.ti.com
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
9 Power Supply Recommendations
The LMZ23610 device is designed to operate from an input voltage supply range between 6 V and 36 V. This
input supply must be well regulated and able to withstand maximum input current and maintain a stable voltage.
The resistance of the input supply rail must be low enough that an input current transient does not cause a high
enough drop at the LMZ23610 supply voltage that can cause a false UVLO fault triggering and system reset. If
the input supply is more than a few inches from the LMZ23610, additional bulk capacitance may be required in
addition to the ceramic bypass capacitors. The amount of bulk capacitance is not critical, but a 47-μF or 100-μF
electrolytic capacitor is a typical choice.
10 Layout
10.1 Layout Guidelines
PC board layout is an important part of DC-DC converter design. Poor board layout can disrupt the performance
of a DC-DC converter and surrounding circuitry by contributing to EMI, ground bounce and resistive voltage drop
in the traces. These can send erroneous signals to the DC-DC converter resulting in poor regulation or instability.
Good layout can be implemented by following a few simple design rules. A good layout example is shown in
Figure 59.
1. Minimize area of switched current loops.
From an EMI reduction standpoint, it is imperative to minimize the high di/dt paths during PCB layout as
shown in Figure 56 above. The high current loops that do not overlap have high di/dt content that will cause
observable high frequency noise on the output pin if the input capacitor (CIN) is placed at a distance away
from the LMZ23610. Therefore place CIN as close as possible to the LMZ23610 VIN and PGND exposed
pad. This will minimize the high di/dt area and reduce radiated EMI. Additionally, grounding for both the input
and output capacitor must consist of a localized top side plane that connects to the PGND exposed pad
(EP).
2. Have a single point ground.
The ground connections for the feedback, soft-start, and enable components must be routed to the AGND
pin of the device. This prevents any switched or load currents from flowing in the analog ground traces. If not
properly handled, poor grounding can result in degraded load regulation or erratic output voltage ripple
behavior. Additionally provide a single point ground connection from pin 4 (AGND) to EP/PGND.
3. Minimize trace length to the FB pin.
Both feedback resistors, RFBT and RFBB must be located close to the FB pin. Because the FB node is high
impedance, maintain the copper area as small as possible. The traces from RFBT, RFBB must be routed away
from the body of the LMZ23610 to minimize possible noise pickup.
4. Make input and output bus connections as wide as possible.
This reduces any voltage drops on the input or output of the converter and maximizes efficiency. To optimize
voltage accuracy at the load, ensure that a separate feedback voltage sense trace is made to the load. Doing
so will correct for voltage drops and provide optimum output accuracy.
5. Provide adequate device heat-sinking.
Use an array of heat-sinking vias to connect the exposed pad to the ground plane on the bottom PCB layer.
If the PCB has multiple copper layers, these thermal vias can also be connected to inner layer heatspreading ground planes. For best results use a 10 x 10 via array or larger with a minimum via diameter of 8
mil thermal vias spaced 46.8 mil (1.5 mm). Ensure enough copper area is used for heat-sinking to keep the
junction temperature below 125°C.
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
25
LMZ23610
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
www.ti.com
10.2 Layout Examples
VOUT
VIN
VOUT
VIN
High
di/dt
CIN
COUT
PGND
Loop 2
Loop 1
Figure 56. Critical Current Loops to Minimize
Top View
Thermal Vias
GND
GND
3
4 5
6 7 8 9 10 11
AGND
EN
SH
SS
FB
AGND
COUT
VOUT
VOUT
2
VIN
VIN
EPAD
1
SYNC
VIN
CIN
VOUT
CSS
Clock >
RFBT
Enable >
CFF
RFBB
GND Plane
Figure 57. PCB Layout Guide
26
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
LMZ23610
www.ti.com
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
Layout Examples (continued)
Figure 58. Top View of Evaluation PCB
Figure 59. Bottom View of Evaluation PCB
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
27
LMZ23610
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
www.ti.com
10.3 Power Dissipation and Thermal Considerations
When calculating module dissipation use the maximum input voltage and the average output current for the
application. Many common operating conditions are provided in the characteristic curves such that less common
applications can be derived through interpolation. In all designs, the junction temperature must be kept below the
rated maximum of 125°C.
For the design case of VIN = 12 V, VOUT = 3.3 V, IOUT = 10 A, and TA-MAX = 50°C, the module must see a thermal
resistance from case to ambient (θCA) of less than:
TJ-MAX ± TA-MAX
- TJC
TCA <
PIC_LOSS
(15)
Given the typical thermal resistance from junction to case (θJC) to be 1.0°C/W. Use the 85°C power dissipation
curves in the Typical Characteristics section to estimate the PIC-LOSS for the application being designed. In this
application it is 5.3 W.
TCA <
125°C - 50°C
- 1.0 °C < 18.23 °C
3.9 W
W
W
(16)
To reach θCA = 13.15, the PCB is required to dissipate heat effectively. With no airflow and no external heat-sink,
a good estimate of the required board area covered by 2-oz. copper on both the top and bottom metal layers is:
Board Area_cm2 8
500 . °C x cm 2
TCA
W
(17)
As a result, approximately 38.02 square cm of 2-oz. copper on top and bottom layers is the minimum required
area for the example PCB design. This is 6.16 × 6.16 cm (2.42 × 2.42 in) square. The PCB copper heat sink
must be connected to the exposed pad. For best performance, use approximately 100, 8 mil thermal vias spaced
59 mil (1.5 mm) apart connect the top copper to the bottom copper.
Another way to estimate the temperature rise of a design is using θJA. An estimate of θJA for varying heat sinking
copper areas and airflows can be found in the typical applications curves. If our design required the same
operating conditions as before but had 225 LFPM of airflow. We locate the required θJA of
TJA <
TJ-MAX - TA-MAX
PIC_LOSS
TJA <
(125 - 50) °C
°C
< 19.23
3.9 W
W
(18)
On the θJA vs copper heatsinking curve, the copper area required for this application is now only 2 square
inches. The airflow reduced the required heat sinking area by a factor of three.
To reduce the heat sinking copper area further, this package is compatible with D3-PAK surface mount heat
sinks.
For an example of a high thermal performance PCB layout for SIMPLE SWITCHER power modules, refer to AN2093 (SNVA460), AN-2084 (SNVA456), AN-2125 (SNVA473), AN-2020 (SNVA419) and AN-2026 (SNVA424).
10.4 Power Module SMT Guidelines
The recommendations below are for a standard module surface mount assembly
• Land Pattern — Follow the PCB land pattern with either soldermask defined or non-soldermask defined pads
• Stencil Aperture
– For the exposed die attach pad (DAP), adjust the stencil for approximately 80% coverage of the PCB land
pattern
– For all other I/O pads use a 1:1 ratio between the aperture and the land pattern recommendation
• Solder Paste — Use a standard SAC Alloy such as SAC 305, type 3 or higher
• Stencil Thickness — 0.125 to 0.15mm
• Reflow — Refer to solder paste supplier recommendation and optimized per board size and density
• Refer to Design Summary LMZ1xxx and LMZ2xxx Power Modules Family (SNAA214) for reflow information
28
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
LMZ23610
www.ti.com
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
Power Module SMT Guidelines (continued)
•
Maximum number of reflows allowed is one
Figure 60. Sample Reflow Profile
Table 2. Sample Reflow Profile Table
PROBE
MAX TEMP
(°C)
REACHED
MAX TEMP
TIME ABOVE
235°C
REACHED
235°C
TIME ABOVE
245°C
REACHED
245°C
TIME ABOVE
260°C
REACHED
260°C
1
242.5
6.58
0.49
6.39
2
242.5
7.10
0.55
6.31
0.00
–
0.00
–
0.00
7.10
0.00
3
241.0
7.09
0.42
6.44
–
0.00
–
0.00
–
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
29
LMZ23610
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
www.ti.com
11 Device and Documentation Support
11.1 Device Support
11.1.1 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
11.1.2 Development Support
For developmental support, see the following:
WEBENCH Tool, http://www.ti.com/webench
11.2 Documentation Support
11.2.1 Related Documentation
For related documentation, see the following:
• AN-2027 Inverting Application for the LMZ14203 SIMPLE SWITCHER Power Module, (SNVA425)
• Absolute Maximum Ratings for Soldering, (SNOA549)
• AN-2024 LMZ1420x / LMZ1200x Evaluation Board (SNVA422)
• AN-2085 LMZ23605/03, LMZ22005/03 Evaluation Board (SNVA457)
• AN-2054 Evaluation Board for LM10000 - PowerWise AVS System Controller (SNVA437)
• AN-2020 Thermal Design By Insight, Not Hindsight (SNVA419)
• AN-2093 LMZ23610/8/6 and LMZ22010/8/6 Current Sharing Evaluation Board (SNVA460)
• AN-2026 Effect of PCB Design on Thermal Performance of SIMPLE SWITCHER Power Modules (SNVA424)
• Design Summary LMZ1xxx and LMZ2xxx Power Modules Family (SNAA214)
11.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.4 Trademarks
E2E is a trademark of Texas Instruments.
SIMPLE SWITCHER, WEBENCH are registered trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.
11.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
30
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
LMZ23610
www.ti.com
SNVS707F – MARCH 2011 – REVISED AUGUST 2015
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: LMZ23610
31
PACKAGE OPTION ADDENDUM
www.ti.com
4-May-2015
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LMZ23610TZ/NOPB
ACTIVE
PFM
NDY
11
32
Green (RoHS
& no Sb/Br)
CU SN
Level-3-245C-168 HR
-40 to 85
LMZ23610
LMZ23610TZE/NOPB
ACTIVE
PFM
NDY
11
250
Green (RoHS
& no Sb/Br)
CU SN
Level-3-245C-168 HR
-40 to 85
LMZ23610
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
4-May-2015
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
4-May-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
LMZ23610TZE/NOPB
Package Package Pins
Type Drawing
PFM
NDY
11
SPQ
250
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
330.0
32.4
Pack Materials-Page 1
15.45
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
18.34
6.2
20.0
32.0
Q2
PACKAGE MATERIALS INFORMATION
www.ti.com
4-May-2015
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LMZ23610TZE/NOPB
PFM
NDY
11
250
367.0
367.0
55.0
Pack Materials-Page 2
MECHANICAL DATA
NDY0011A
BOTTOM SIDE OF PACKAGE
TOP SIDE OF PACKAGE
TZA11A (Rev F)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated