NCP612, NCV612 100 mA CMOS Low Iq Voltage Regulator in an SC70-5 The NCP612/NCV612 series of fixed output linear regulators are designed for handheld communication equipment and portable battery powered applications which require low quiescent. The NCP612/NCV612 series features an ultra−low quiescent current of 40 A. Each device contains a voltage reference unit, an error amplifier, a PMOS power transistor, resistors for setting output voltage, current limit, and temperature limit protection circuits. The NCP612/NCV612 has been designed to be used with low cost ceramic capacitors. The device is housed in the micro−miniature SC70−5 surface mount package. Standard voltage versions are 1.5, 1.8, 2.5, 2.7, 2.8, 3.0, 3.1, 3.3, 3.7, and 5.0 V. Features • • • • • • • Low Quiescent Current of 40 A Typical Low Dropout Voltage of 230 mV at 100 mA and 3.0 V Vout Low Output Voltage Option Output Voltage Accuracy of 2.0% Temperature Range of −40°C to 85°C (NCP612) Temperature Range of −40°C to 125°C (NCV612) NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP Capable These are Pb−Free Devices www.onsemi.com SC70−5 CASE 419A PIN CONNECTIONS Vin 1 Gnd 2 Enable 3 Vout 4 N/C (Top View) MARKING DIAGRAM 5 xxxM G G Typical Applications • • • • 5 1 Cellular Phones Battery Powered Consumer Products Hand−Held Instruments Camcorders and Cameras xxx = Specific Device Code M = Date Code* G = Pb−Free Package (Note: Microdot may be in either location) Battery or Unregulated Voltage ORDERING INFORMATION Vout C1 + 1 5 + 2 ON 3 See detailed ordering and shipping information in the package dimensions section on page 8 of this data sheet. C2 4 OFF This device contains 86 active transistors Figure 1. Typical Application Diagram © Semiconductor Components Industries, LLC, 2013 April, 2017 − Rev. 4 1 Publication Order Number: NCP612/D NCP612, NCV612 ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ PIN FUNCTION DESCRIPTION Pin No. Pin Name 1 Vin Positive power supply input voltage. Description 2 Gnd Power supply ground. 3 Enable 4 N/C No internal connection. 5 Vout Regulated output voltage. This input is used to place the device into low−power standby. When this input is pulled low, the device is disabled. If this function is not used, Enable should be connected to Vin. MAXIMUM RATINGS Rating Symbol Value Unit Vin 0 to 6.0 V Enable Voltage Enable −0.3 to Vin +0.3 V Output Voltage Vout −0.3 to Vin +0.3 V Power Dissipation and Thermal Characteristics Power Dissipation Thermal Resistance, Junction−to−Ambient PD RJA Internally Limited 300 W °C/W TJ +150 °C Operating Ambient Temperature TA −40 to +125 °C Storage Temperature Tstg −55 to +150 °C Input Voltage Operating Junction Temperature Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. This device series contains ESD protection and exceeds the following tests: Human Body Model 2000 V per MIL−STD−883, Method 3015 Machine Model Method 200 V 2. Latch−up capability (85°C) "200 mA DC with trigger voltage. ELECTRICAL CHARACTERISTICS (Vin = Vout(nom.) + 1.0 V, Venable = Vin, Cin = 1.0 F, Cout = 1.0 F, TJ = 25°C, unless otherwise noted.) Characteristic Symbol Output Voltage (TA = 25°C, Iout = 10 mA) 1.5 V 1.8 V 2.5 V 2.7 V 2.8 V 3.0 V 3.1 V 3.3 V 3.7 V 5.0 V Vout Output Voltage (TA = −40°C to 85°C, Iout = 10 mA) 1.5 V 1.8 V 2.5 V 2.7 V 2.8 V 3.0 V 3.1 V 3.3 V 3.7 V 5.0 V Vout www.onsemi.com 2 Min Typ Max 1.455 1.746 2.425 2.646 2.744 2.940 3.038 3.234 3.626 4.900 1.5 1.8 2.5 2.7 2.8 3.0 3.1 3.3 3.7 5.0 1.545 1.854 2.575 2.754 2.856 3.060 3.162 3.366 3.774 5.100 1.455 1.746 2.425 2.619 2.716 2.910 3.007 3.201 3.626 4.900 1.5 1.8 2.5 2.7 2.8 3.0 3.1 3.3 3.7 5.0 1.545 1.854 2.575 2.781 2.884 3.090 3.193 3.399 3.774 5.100 Unit V V NCP612, NCV612 ELECTRICAL CHARACTERISTICS (continued) (Vin = Vout(nom.) + 1.0 V, Venable = Vin, Cin = 1.0 F, Cout = 1.0 F, TJ = 25°C, unless otherwise noted.) Characteristic Symbol Output Voltage (TA = −40°C to 125°C, Iout = 10 mA) NCV612 Only 1.5 V 1.8 V 2.5 V 2.7 V 2.8 V 3.0 V 3.1 V 3.3 V 5.0 V Vout Output Voltage (TA = −40°C to 85°C, Iout = 100 mA) 1.5 V 1.8 V 2.5 V 2.7 V 2.8 V 3.0 V 3.1 V 3.3 V 3.7 V 5.0 V Vout Line Regulation (Iout = 10 mA) 1.5 V−4.4 V (Vin = Vout(nom.) + 1.0 V to 6.0 V) 4.5 V−5.0 V (Vin = 5.5 V to 6.0 V) Regline Load Regulation (Iout = 1.0 mA to 100 mA) Regload Output Current (Vout = (Vout at Iout = 100 mA) −3%) 1.5 V−3.9 V (Vin = Vout(nom.) + 2.0 V) 4.0 V−5.0 V (Vin = 6.0 V) Io(nom.) Dropout Voltage (TA = −40°C to 85°C, Iout = 100 mA, Measured at Vout(nom) −3.0%) 1.5 V 1.8 V 2.5 V 2.7 V 2.8 V 3.0 V 3.1 V 3.3 V 3.7 V 5.0 V Vin−Vout Ground Current (Enable Input = Vin, Iout = 1.0 mA to Io(nom.)) IGND Quiescent Current (TA = −40°C to 85°C) (Enable Input = 0 V) (Enable Input = Vin, Iout = 1.0 mA to Io(nom.)) IQ Output Short Circuit Current (Vout = 0 V) 1.5 V−3.9 V (Vin = Vout(nom.) + 2.0 V) 4.0 V−5.0 V (Vin = 6.0 V) Min Typ Max 1.440 1.728 2.400 2.592 2.688 2.880 2.976 3.201 4.850 1.5 1.8 2.5 2.7 2.8 3.0 3.1 3.3 5.0 1.560 1.872 2.600 2.808 2.912 3.120 3.224 3.399 5.150 1.440 1.728 2.400 2.592 2.688 2.880 2.976 3.201 3.589 4.850 1.5 1.8 2.5 2.7 2.8 3.0 3.1 3.3 3.7 5.0 1.560 1.872 2.600 2.808 2.912 3.120 3.224 3.399 3.811 5.150 − − 1.0 1.0 3.0 3.0 − 0.3 0.8 100 100 200 200 − − V V mV/V mV − − − − − − − − − − 530 420 270 270 250 230 210 200 180 160 680 560 380 380 380 380 380 380 380 300 − 40 90 − − 0.03 40 1.0 90 150 150 300 300 600 600 − 100 − 0.95 − − − − 0.3 − "100 − A A mA Vrms Vn Enable Input Threshold Voltage (Voltage Increasing, Output Turns On, Logic High) (Voltage Decreasing, Output Turns Off, Logic Low) Vth(en) Output Voltage Temperature Coefficient TC V 3. Maximum package power dissipation limits must be observed. T *TA PD + J(max) RJA 4. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. www.onsemi.com 3 mV/mA mA Iout(max) Output Voltage Noise (f = 100 Hz to 100 kHz) Iout = 30 mA, Cout = 1 F Unit ppm/°C NCP612, NCV612 300 3.020 NCP612SQ30 Vout, OUTPUT VOLTAGE (V) Vin − Vout, DROPOUT VOLTAGE (mV) TYPICAL CHARACTERISTICS 250 Io = 80 mA 200 150 Io = 40 mA 100 50 Io = 10 mA 0 −50 −25 0 25 50 75 100 3.015 Vin = 6.0 V 3.010 Vin = 4.0 V 3.005 3.000 2.995 2.990 2.985 −60 125 −40 −20 0 TEMPERATURE (°C) Iq, QUIESCENT CURRENT (A) Iq, QUIESCENT CURRENT (A) 44 42 40 −60 100 −40 −20 0 20 40 60 80 Vout = 3.0 V Cin = 1.0 F Cout = 1.0 F TA = 25°C 50 40 30 20 10 0 0 100 1 2 3 4 5 6 7 Vin INPUT VOLTAGE (V) TEMPERATURE (°C) Figure 5. Quiescent Current vs. Input Voltage Figure 4. Quiescent Current vs. Temperature 60 70 Vout = 3.0 V Cin = 1.0 F Cout = 1.0 F Iout = 30 mA TA = 25°C Vin = 4.0 V Cout = 1.0 F Iout = 30 mA 60 RIPPLE REJECTION (dB) Ignd, GROUND CURRENT (A) 80 60 Iout = 0 mA Vin = 4.0 V Vout = 3.0 V 46 30 20 10 0 0 60 Figure 3. Output Voltage vs. Temperature 48 40 40 TEMPERATURE (°C) Figure 2. Dropout Voltage vs. Temperature 50 20 50 40 30 20 10 1 2 3 4 5 6 0 100 7 1000 10000 100000 1000000 Vin INPUT VOLTAGE (V) FREQUENCY (Hz) Figure 6. Ground Pin Current vs. Input Voltage Figure 7. Ripple Rejection vs. Frequency www.onsemi.com 4 NCP612, NCV612 TYPICAL CHARACTERISTICS 7 Vin, INPUT VOLTAGE (V) Vin = 4.0 V Cout = 1.0 F Iout = 30 mA 6 5 4 OUTPUT VOLTAGE DEVIATION (mV) OUTPUT VOLTAGE NOISE (V/ǰHz) 7 3 2 1 6 Cout = 1.0 F Iout = 10 mA 5 4 3 200 100 0 −100 0 10 1000 100 10000 100000 1000000 0 50 100 150 200 250 Figure 9. Line Transient Response Figure 8. Output Noise Density Vin, INPUT VOLTAGE (V) 6 60 mA 0 200 4 2 0 4 OUTPUT VOLTAGE (V) 100 0 Iout = 1 mA to 60 mA Vin = 4.0 V Cin = 1.0 F Cout = 1.0 F −100 −200 0 100 200 300 400 500 600 700 Iout = 10 mA Vin = 4.0 V Cin = 1.0 F Cout = 1.0 F 3 2 1 0 0 800 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 TIME (s) TIME (ms) Figure 10. Load Transient Response Figure 11. Turn−on Response 3.5 Vout, OUTPUT VOLTAGE (V) Io, OUTPUT CURRENT (mA) 500 TIME (s) FREQUENCY (Hz) OUTPUT VOLTAGE DEVIATION (mV) 300 350 400 450 3.0 2.5 2.0 1.5 1.0 0.5 0 0 1.0 2.0 3.0 4.0 5.0 Vin, INPUT VOLTAGE (V) Figure 12. Output Voltage vs. Input Voltage www.onsemi.com 5 6.0 1.8 2.0 NCP612, NCV612 DEFINITIONS Load Regulation Line Regulation The change in output voltage for a change in output current at a constant temperature. The change in output voltage for a change in input voltage. The measurement is made under conditions of low dissipation or by using pulse technique such that the average chip temperature is not significantly affected. Dropout Voltage The input/output differential at which the regulator output no longer maintains regulation against further reductions in input voltage. Measured when the output drops 3.0% below its nominal. The junction temperature, load current, and minimum input supply requirements affect the dropout level. Line Transient Response Typical over and undershoot response when input voltage is excited with a given slope. Thermal Protection Internal thermal shutdown circuitry is provided to protect the integrated circuit in the event that the maximum junction temperature is exceeded. When activated at typically 160°C, the regulator turns off. This feature is provided to prevent failures from accidental overheating. Maximum Power Dissipation The maximum total dissipation for which the regulator will operate within its specifications. Quiescent Current The quiescent current is the current which flows through the ground when the LDO operates without a load on its output: internal IC operation, bias, etc. When the LDO becomes loaded, this term is called the Ground current. It is actually the difference between the input current (measured through the LDO input pin) and the output current. Maximum Package Power Dissipation The maximum power package dissipation is the power dissipation level at which the junction temperature reaches its maximum operating value, i.e. 150°C. Depending on the ambient power dissipation and thus the maximum available output current. www.onsemi.com 6 NCP612, NCV612 APPLICATIONS INFORMATION Thermal A typical application circuit for the NCP612/NCV612 is shown in Figure 1, front page. As power across the NCP612/NCV612 increases, it might become necessary to provide some thermal relief. The maximum power dissipation supported by the device is dependent upon board design and layout. Mounting pad configuration on the PCB, the board material and also the ambient temperature effect the rate of temperature rise for the part. This is stating that when the NCP612/NCV612 has good thermal conductivity through the PCB, the junction temperature will be relatively low with high power dissipation applications. The maximum dissipation the package can handle is given by: Input Decoupling (C1) A 1.0 F capacitor either ceramic or tantalum is recommended and should be connected close to the NCP612/NCV612 package. Higher values and lower ESR will improve the overall line transient response. TDK capacitor: C2012X5R1C105K, or C1608X5R1A105K Output Decoupling (C2) The NCP612/NCV612 is a stable regulator and does not require any specific Equivalent Series Resistance (ESR) or a minimum output current. Capacitors exhibiting ESRs ranging from a few m up to 5.0 can thus safely be used. The minimum decoupling value is 1.0 F and can be augmented to fulfill stringent load transient requirements. The regulator accepts ceramic chip capacitors as well as tantalum capacitors. Larger values improve noise rejection and load regulation transient response. TDK capacitor: C2012X5R1C105K, C1608X5R1A105K, or C3216X7R1C105K T *TA PD + J(max) RJA If junction temperature is not allowed above the maximum 125°C, then the NCP612/NCV612 can dissipate up to 330 mW @ 25°C. The power dissipated by the NCP612/NCV612 can be calculated from the following equation: Ptot + ƪVin * Ignd (Iout)ƫ ) [Vin * Vout] * Iout Enable Operation or The enable pin will turn on the regulator when pulled high and turn off the regulator when pulled low. These limits of threshold are covered in the electrical specification section of this data sheet. If the enable is not used then the pin should be connected to Vin. P ) Vout * Iout VinMAX + tot Ignd ) Iout If an 100 mA output current is needed then the ground current from the data sheet is 40 A. For an NCP612/NCV612 (3.0 V), the maximum input voltage will then be 6.0 V (Limited by maximum input voltage). Hints Please be sure the Vin and Gnd lines are sufficiently wide. When the impedance of these lines is high, there is a chance to pick up noise or cause the regulator to malfunction. Set external components, especially the output capacitor, as close as possible to the circuit, and make leads as short as possible. www.onsemi.com 7 NCP612, NCV612 ORDERING INFORMATION Nominal Output Voltage Marking NCP612SQ15T2G 1.5 LHO NCP612SQ18T2G 1.8 LHP NCP612SQ25T2G 2.5 LHQ NCP612SQ27T2G 2.7 LHR NCP612SQ28T2G 2.8 LHS NCP612SQ30T2G 3.0 LHT NCP612SQ31T2G 3.1 LHU NCP612SQ33T2G 3.3 LHV NCP612SQ37T2G 3.7 LKH NCP612SQ50T2G 5.0 LHW NCV612SQ15T2G* 1.5 LHO NCV612SQ18T2G* 1.8 LHP NCV612SQ25T2G* 2.5 LHQ NCV612SQ27T2G* 2.7 LHR NCV612SQ28T2G* 2.8 LHS NCV612SQ30T2G* 3.0 LHT NCV612SQ31T2G* 3.1 LHU NCV612SQ33T2G* 3.3 LHV NCV612SQ37T2G* 3.7 LKH NCV612SQ50T2G* 5.0 LHW Device Package Shipping† SC70−5 (Pb−Free) 3000 Units/Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. *NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP Capable. www.onsemi.com 8 NCP612, NCV612 PACKAGE DIMENSIONS SC−88A (SC−70−5/SOT−353) CASE 419A−02 ISSUE L A NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 419A−01 OBSOLETE. NEW STANDARD 419A−02. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. G 5 4 −B− S 1 2 0.2 (0.008) D 5 PL B M INCHES MIN MAX 0.071 0.087 0.045 0.053 0.031 0.043 0.004 0.012 0.026 BSC --0.004 0.004 0.010 0.004 0.012 0.008 REF 0.079 0.087 DIM A B C D G H J K N S 3 M N MILLIMETERS MIN MAX 1.80 2.20 1.15 1.35 0.80 1.10 0.10 0.30 0.65 BSC --0.10 0.10 0.25 0.10 0.30 0.20 REF 2.00 2.20 J C K H SOLDER FOOTPRINT 0.50 0.0197 0.65 0.025 0.65 0.025 0.40 0.0157 1.9 0.0748 SCALE 20:1 mm Ǔ ǒinches ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] ◊ N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 www.onsemi.com 9 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NCP612/D