Technical Sales United States (866) 531-6285 [email protected] Detailed Specifications | Pinouts/Front Panel Connections For user manuals and dimensional drawings, visit the product page resources tab on ni.com. Last Revised: 2013-03-19 09:30:00.0 250 MS/s, 14-Bit Digitizer Adapter Module for NI FlexRIO NI 5761 250 MS/s sample rate at 14-bit resolution Requires an NI FlexRIO FPGA module 4 channels, simultaneously sampled Requires programming with LabVIEW FPGA or HDL AC- and DC-coupled versions Overview The NI 5761 adapter module for NI FlexRIO is a broadband high-performance digitizer designed to meet a wide range of signal processing application needs. The module features four analog input channels with 14-bit resolution. With an analog bandwidth of 500 MHz and a sample rate of 250 MS/s, the NI 5761 is ideal for undersampling IF communications signals up to the 4th Nyquist zone. Eight built-in digital I/O lines are suitable for a variety of applications, from implementing custom triggering to control of system upconverters or downconverters. Back to Top Application and Technology The NI 5761 digitizer adapter module for NI FlexRIO uses the Texas Instruments ADS62P49 analog-to-digital converter (ADC), offering excellent 14-bit dynamic performance ideal for IF and RF communications applications: Table 1. Key Typical Specifications for the NI 5761 Figure 1. AC-Coupled Spectral Measurements: 20.1 MHz, -1 dBFS, 8192-Point FFT, 10 RMS Average 1/14 www.ni.com Figure 2. DC-Coupled Spectral Measurements: 20.1 MHz, -1 dBFS, 8192-Point FFT, 10 RMS Average Coupled with an NI FlexRIO field-programmable gate array (FPGA) module, the NI 5761 provides a powerful solution for applications requiring a high-speed digitizer with excellent 14-bit dynamic performance and a user-accessible FPGA for custom real-time processing. Application Example Algorithms Custom communications receivers Custom modulation and demodulation, bit error rate test, fading profiles, additive noise IF acquisition at the common frequencies of 10.7 MHz, 70 MHz, and 140 MHz, and band-limited direct RF acquisition Digital downconversion, demodulation, packet assembly Phase-coherent MIMO acquisition Algorithm prototyping, cross-correlation Signals intelligence FFT operations, digital downconversion, channelization, triggering, cross-correlation High-resolution time domain measurements Custom data triggers, hysteresis, time in region, timing and voltage measurements Table 2. Key Typical Specifications for the NI 5761 About NI FlexRIO The NI FlexRIO family consists of PXI and PXI Express FPGA modules coupled to I/O adapter modules. Programmed with the NI LabVIEW FPGA Module, these modules together provide high-performance I/O and user-defined hardware processing on the PXI platform. Figure 3. NI FlexRIO Architecture 2/14 www.ni.com NI FlexRIO FPGA modules feature the latest in FPGA technology and high-performance bus interfaces. Table 3. NI FlexRIO FPGA Module Options PXI Express NI FlexRIO FPGA modules incorporate Xilinx Virtex-5 SXT FPGAs with up to 512 MB of onboard DRAM, which you can access at bandwidths up to 3.2 GB/s. In addition to general-purpose reconfigurable logic, SXT FPGAs are optimized for high-speed digital signal processing (DSP), with up to 640 DSP slices for single-cycle multiplication and filtering functions. PXI Express NI FlexRIO FPGA modules also feature the NI STC-3 application-specific integrated circuit (ASIC), providing an optimized, high-bandwidth PCI Express x4 communications link to the backplane of the PXI Express chassis. This ASIC reduces the FPGA resources needed to implement host communication and enables new data transfer technology in the unique peer-to-peer (P2P) streaming feature. With NI P2P data streaming technology, you can continuously transfer data to and from PXI Express NI FlexRIO FPGA modules at rates greater than 800 MB/s for additional processing and I/O integration. You can also stream to and from select PXI Express NI modular instruments for an even greater variety of I/O. PXI NI FlexRIO FPGA modules feature Xilinx Virtex-5 LX FPGAs with up to 128 MB of onboard DRAM, which you can access at bandwidths up to 1.6 GB/s. They feature all the benefits of the PXI platform including synchronization, triggering, and high-speed data transfer to and from their hosts. Table 4. PXI and PXI Express FPGA Module Comparison National Instruments and third parties offer NI FlexRIO adapter modules, and you can build your own adapter modules using the NI FlexRIO Adapter Module Development Kit (MDK). With custom adapter modules, you can implement the exact analog and digital I/O your application requires, along with graphical FPGA programming provided by LabVIEW. View a current list of NI and third-party adapter modules at ni.com/flexrio. This ability to easily create high-bandwidth P2P data streams helps provide scalable signal processing and I/O integration. LabVIEW FPGA With the high-level graphical programming capabilities of LabVIEW FPGA, programming for the NI 5761 is far simpler than low-level HDL programming. Figure 4 depicts acquiring samples from a digitizer adapter module at its configured rate and placing the data into an FPGA FIFO. Figure 4. LabVIEW FPGA Code for Acquiring Data from an NI FlexRIO Digitizer Adapter Module From this point, you may implement your own processing, filtering, fast Fourier transform (FFT), or control. Figure 5 shows custom demodulation using IP from the FPGA RF Communications Library on ni.com/labs. 3/14 www.ni.com Figure 5. LabVIEW FPGA Code for Demodulating and Decoding I and Q Signals after 4X Decimation For implementing a real-time spectrum analyzer, Figure 6 shows code that performs windowing, conversion to the frequency domain, comparison against a frequency mask, and assertion of a trigger when that mask is exceeded. Figure 6. LabVIEW FPGA Code for Real-Time Spectrum Analyzer Finally, Figure 7 shows a custom, 128-tap inline finite impulse response (FIR) filter with reloadable coefficients. After filtering, the data is generated through a digital-to-analog converter. Figure 7. LabVIEW FPGA Code for an Inline Filter Back to Top Support and Services System Assurance Programs NI system assurance programs are designed to make it even easier for you to own an NI system. These programs include configuration and deployment services for your NI PXI, CompactRIO, or Compact FieldPoint system. The NI Basic System Assurance Program provides a simple integration test and ensures that your system is delivered completely assembled in one box. When you configure your system with the NI Standard System Assurance Program, you can select from available NI system driver sets and application development environments to create customized, reorderable software configurations. Your system arrives fully assembled and tested in one box with your software preinstalled. When you order your system with the standard program, you also receive system-specific documentation including a bill of materials, an integration test report, a recommended maintenance plan, and frequently asked question documents. Finally, the standard program reduces the total cost of owning an NI system by providing three years of warranty coverage and calibration service. Use the online product advisors at ni.com/advisor to find a system assurance program to meet your needs. Technical Support Get answers to your technical questions using the following National Instruments resources. Support - Visit ni.com/support to access the NI KnowledgeBase, example programs, and tutorials or to contact our applications engineers who are located in NI sales offices around the world and speak the local language. Discussion Forums - Visit forums.ni.com for a diverse set of discussion boards on topics you care about. Online Community - Visit community.ni.com to find, contribute, or collaborate on customer-contributed technical content with users like you. 4/14 www.ni.com Repair While you may never need your hardware repaired, NI understands that unexpected events may lead to necessary repairs. NI offers repair services performed by highly trained technicians who quickly return your device with the guarantee that it will perform to factory specifications. For more information, visit ni.com/repair. Training and Certifications The NI training and certification program delivers the fastest, most certain route to increased proficiency and productivity using NI software and hardware. Training builds the skills to more efficiently develop robust, maintainable applications, while certification validates your knowledge and ability. Classroom training in cities worldwide - the most comprehensive hands-on training taught by engineers. On-site training at your facility - an excellent option to train multiple employees at the same time. Online instructor-led training - lower-cost, remote training if classroom or on-site courses are not possible. Course kits - lowest-cost, self-paced training that you can use as reference guides. Training memberships and training credits - to buy now and schedule training later. Visit ni.com/training for more information. Extended Warranty NI offers options for extending the standard product warranty to meet the life-cycle requirements of your project. In addition, because NI understands that your requirements may change, the extended warranty is flexible in length and easily renewed. For more information, visit ni.com/warranty. OEM NI offers design-in consulting and product integration assistance if you need NI products for OEM applications. For information about special pricing and services for OEM customers, visit ni.com/oem. Alliance Our Professional Services Team is comprised of NI applications engineers, NI Consulting Services, and a worldwide National Instruments Alliance Partner program of more than 700 independent consultants and integrators. Services range from start-up assistance to turnkey system integration. Visit ni.com/alliance. Back to Top Detailed Specifications This section lists the specifications of the NI FlexRIO adapter module (NI 5761). Pair these specifications with the specifications listed in the NI FlexRIO FPGA Module Installation Guide and Specifications. For more information about safety and electromagnetic compatibility refer to the Read Me First: Safety and Electromagnetic Compatibility document included in your hardware kit or available at ni.com/manuals. Caution To avoid permanent damage to the NI 5761, disconnect all signals connected to the NI 5761 before powering down the module, and only connect signals after the module has been powered on by the NI FlexRIO FPGA module. Note All numeric specifications are typical unless otherwise noted. All graphs illustrate the performance of a representative module. Typical values describe useful product performance that are not covered by warranty. Typical values cover the expected performance of units over ambient temperature ranges of 23 ±5 °C with a 90% confidence level, based on measurements taken during development or production. Analog Input (AI CH 0 through AI CH 3) General Characteristics Number of channels Four, single-ended, simultaneously sampled Connector SMA Input impedance 50 Ω, per connector Sample rate Internal Sample clock 250 MHz External Sample clock 175 MHz to 250 MHz Digital data range ±8,191 ADC part number ADS62P49 1 ; 14-bit resolution, dual ADC AC-Coupled Specifications Input range (normal operating conditions) 2.07 Vpk-pk Absolute maximum input ±10 V DC, 5 Vpk-pk AC 0.1 MHz to 500 MHz Bandwidth (–3 dB) 1 MHz to 250 MHz Bandwidth (–1 dB) The following table lists the AC-coupled spectral performance measurements. All values are measured with a 250 MHz external Sample clock. 5/14 www.ni.com AC-Coupled Spectral Performance Measurement 20.17 MHz 70.17 MHz* 123.17 MHz* SNR 72.5 dB 71.4 dB 70.5 dB SINAD 72.3 dB 71.2 dB 70.3 dB SFDR 88 dB 84 dB 80 dB * These measurements were extrapolated from a –4 dBFS plot. Channel to channel isolation 1 MHz >90 dB 100.1 MHz 90 dB 501 MHz 80 dB AC-Coupled Measurements AC-Coupled Bandwidth (Passband) AC-Coupled Spectral Measurements: 19.5 MHz and 20.5 MHz, –13 dBFS, 8,192 Point FFT, 10 RMS Average AC-Coupled Spectral Measurements: 20.1 MHz, –1 dBFS, 8,192 Point FFT, 10 RMS Average 6/14 www.ni.com AC-Coupled Spectral Measurements: Terminated, 8,192 Point FFT, 10 RMS Average DC-Coupled Specifications Input range (normal operating conditions) 1.23 Vpk-pk Absolute maximum input ±4.5 V DC Bandwidth (–3 dB) DC to 500 MHz Bandwidth (–1 dB) DC to 250 MHz The following table lists the DC-coupled spectral performance measurements. All values are measured with a 250 MHz external Sample clock. DC-Coupled Spectral Performance Measurement 20.1 MHz 70.1 MHz 122.1 MHz SNR 65.7 dB 64.3 dB 63 dB SINAD 65.2 dB 61.8 dB 56.6 dB SFDR 76 dB 65 dB 58 dB Channel to channel isolation 1 MHz >90 dB 100.1 MHz 80 dB 501 MHz 70 dB Note To ensure proper device operation, DC-coupled channels on the NI 5761 must see 50 Ω at DC looking back at their source. If you are connecting a to source with an output impedance less than 50 Ω, you can add series resistance close to the source to properly bias the NI 5761 input terminals. You can also use the NI 5761 input 7/14 www.ni.com channel bias DACs to remove DC offset present in the system. For more information about programming the bias DACs, refer to the NI 5761 CLIP topics in the NI FlexRIO Help. DC-Coupled Measurements DC-Coupled Bandwidth (Passband) DC-Coupled Spectral Measurements: 19.5 MHz and 20.5 MHz, –13 dBFS, 8,192 Point FFT, 10 RMS Average DC-Coupled Spectral Measurements: 20.1 MHz, –1 dBFS, 8,192 Point FFT, 10 RMS Average DC-Coupled Spectral Measurements: Terminated, 8,192 Point FFT, 10 RMS Average 8/14 www.ni.com Analog Input Phase Noise Internal Sample Clock General Characteristics Oscillator type Fixed frequency synthesizer Frequency 250 MHz <70 dBc Reference spurs Phase noise –100 dBc/Hz 10 kHz offset –120 dBc/Hz 100 kHz offset Clock distribution part number AD9512 2 ; clock distribution Reference clock sources Internal, External through the CLK IN connector, or IoModSyncClk 3 TCXO Internal reference type ±1 ppm Internal reference stability 10 MHz Internal reference frequency CLK IN General Characteristics Number of channels 1, single-ended Connector SMA 9/14 www.ni.com 50 Ω Input impedance AC Input coupling External Sample Clock 0.63 Vpk-pk to 2.5 Vpk-pk Input voltage range 175 MHz to 250 MHz Input frequency range ±10 V DC, 3.1 Vpk-pk AC Absolute maximum input External Reference Clock Input voltage range 1.4 Vpk-pk to 4.4 Vpk-pk Input frequency range 10 MHz Absolute maximum input ±10 V DC, 5 Vpk-pk AC External Trigger General Characteristics 1, single-ended Number of channels SMA Connector Input impedance 50 Ω Input coupling DC Input levels Voltage Level Minimum Maximum VIL 0V 0.7 V VIH 1.7 V 5.5 V –0.5 V to 7 V Absolute maximum input PFI<0..7> General Characteristics 8 bidirectional Number of channels Micro–D Connector type 2.5 V LVCMOS Interface standard Interface logic Voltage Level Minimum Maximum VIL 0V 0.7 V VIH 1.7 V 5.5 V VOL 0V 0.4 V VOH 1.9 V 2.5 V 17.5 kΩ Zin 50 Ω Zout 2 mA Iout 500 kHz Maximum toggle frequency –0.5 V to 7 V Absolute maximum input EEPROM Map Byte Address Size (Bytes) Field Name 0x0 2 Vendor ID 0x2 2 Product ID 10/14 www.ni.com Byte Address Size (Bytes) Field Name 0x4 4 Serial Number 0x8 116 Reserved 0x7C 132 User Space Caution Only write to User Space. Writing to any other offset may cause the NI 5761 to stop functioning. Power 5.3 W Total power, typical operation Physical Dimensions 12.9 × 2.0 × 12.1 cm (5.1 × 0.8 × 4.7 in.) Weight 312 g (11 oz) Front panel connectors 6 SMA and one Micro-D connector Environmental The NI 5761 is intended for indoor use only. Operating environment 4 0 °C to 55 °C, tested in accordance with IEC-60068-2-1 and IEC-60068-2-2. Relative humidity range 10% to 90%, noncondensing, tested in accordance with IEC-60068-2-56. Altitude 2,000 m at 25 °C ambient temperature. Pollution Degree 2 Storage environment Ambient temperature range –20 °C to 70 °C, tested in accordance with IEC-60068-2-1 and IEC-60068-2-2. Relative humidity range 5% to 95%, noncondensing, tested in accordance with IEC-60068-2-56. Note Clean the device with a soft, non-metallic brush. Make sure that the device is completely dry and free from contaminants before returning it to service. Safety Standards This product is designed to meet the requirements of the following standards of safety for electrical equipment for measurement, control, and laboratory use: IEC 61010-1, EN 61010-1 UL 61010-1, CSA 61010-1 Note For UL and other safety certifications, refer to the product label or the Online Product Certification section. Electromagnetic Compatibility This product meets the requirements of the following EMC standards for electrical equipment for measurement, control, and laboratory use: EN 61326 (IEC 61326): Class A emissions; Basic immunity EN 55011 (CISPR 11): Group 1, Class A emissions AS/NZS CISPR 11: Group 1, Class A emissions FCC 47 CFR Part 15B: Class A emissions ICES-001: Class A emissions Note For the standards applied to assess the EMC of this product, refer to the Online Product Certification section. Note For EMC compliance, operate this device with shielded cables and accessories. CE Compliance This product meets the essential requirements of applicable European Directives as follows: 2006/95/EC; Low-Voltage Directive (safety) 2004/108/EC; Electromagnetic Compatibility Directive (EMC) Online Product Certification To obtain product certifications and the Declaration of Conformity for this product, visit ni.com/certification, search by module number or product line, and click the appropriate link in the Certification column. Environmental Management 11/14 www.ni.com National Instruments is committed to designing and manufacturing products in an environmentally responsible manner. NI recognizes that eliminating certain hazardous substances from our products is beneficial not only to the environment but also to NI customers. For additional environmental information, refer to the NI and the Environment Web page at ni.com/environment. This page contains the environmental regulations and directives with which NI complies, as well as other environmental information not included in this document. Waste Electrical and Electronic Equipment (WEEE) EU Customers At the end of the product life cycle, all products must be sent to a WEEE recycling center. For more information about WEEE recycling centers, National Instruments WEEE initiatives, and compliance with WEEE Directive 2002/96/EC on Waste Electrical and Electronic Equipment, visit ni.com/environment/weee.htm. 1 For additional information on the ADS62P49, refer to the Texas Instruments device data sheet at www.ti.com. 2 For additional information about the AD9512, refer to the Analog Devices device data sheet at www.analog.com. 3 IoModSyncClk is available only on the NI PXIe-796xR FPGA modules. 4 For PXI/PXI Express chassis configurations that group NI FlexRIO adapter modules in three or more contiguous slots, National Instruments recommends limiting the ambient operating temperature to less than 50 °C. Back to Top 12/14 www.ni.com Pinouts/Front Panel Connections NI 5761 Front Panel Connectors 13/14 www.ni.com NI 5761 AUX I/O Connector Pin Assignments Back to Top ©2010 National Instruments. All rights reserved. CompactRIO, FieldPoint, LabVIEW, National Instruments, National Instruments Alliance Partner, NI, ni.com, and NI FlexRIO are trademarks of National Instruments. Other product and company names listed are trademarks or trade names of their respective companies. A National Instruments Alliance Partner is a business entity independent from National Instruments and has no agency, partnership, or joint-venture relationship with National Instruments. My Profile | RSS | Privacy | Legal | Contact NI © 2012 National Instruments Corporation. All rights reserved. 14/14 www.ni.com