MCP661/2/3/5 60 MHz, 6 mA Op Amps Features Description • • • • • • • • The Microchip Technology, Inc. MCP661/2/3/5 family of operational amplifiers features high gain bandwidth product (60 MHz, typical) and high output short circuit current (90 mA, typical). Some also provide a Chip Select pin (CS) that supports a low power mode of operation. These amplifiers are optimized for high speed, low noise and distortion, single-supply operation with rail-to-rail output and an input that includes the negative rail. Gain Bandwidth Product: 60 MHz (typical) Short Circuit Current: 90 mA (typical) Noise: 6.8 nV/√Hz (typical, at 1 MHz) Rail-to-Rail Output Slew Rate: 32 V/µs (typical) Supply Current: 6.0 mA (typical) Power Supply: 2.5V to 5.5V Extended Temperature Range: -40°C to +125°C This family is offered in single (MCP661), single with CS pin (MCP663), dual (MCP662) and dual with two CS pins (MCP665). All devices are fully specified from -40°C to +125°C. Typical Applications • • • • Driving A/D Converters Power Amplifier Control Loops Barcode Scanners Optical Detector Amplifier Typical Application Circuit Design Aids • • • • • • R1 VDD/2 R2 VOUT RL R3 SPICE Macro Models FilterLab® Software Mindi™ Circuit Designer & Simulator Microchip Advanced Part Selector (MAPS) Analog Demonstration and Evaluation Boards Application Notes VIN MCP66X Power Driver with High Gain Package Types MCP661 SOIC NC 1 8 NC MCP663 SOIC MCP662 SOIC VOUTA 1 8 VDD VIN– 2 7 VDD VINA– 2 7 VOUTB VIN+ 3 6 VOUT VINA+ 3 6 VINB– 5 VINB+ VSS 4 VSS 4 5 NC MCP665 MSOP 8 CS VOUTA 1 VIN– 2 7 VDD VIN+ 3 6 VOUT VINA– 2 VINA+ 3 NC 1 VSS 4 5 NC VSS 4 CSA 5 MCP662 3x3 DFN * VOUTA 1 8 VDD VINA– 2 7 VOUTB VINA+ 3 6 VINB– VSS 4 5 VINB+ 10 VDD 9 VOUTB 8 VINB– 7 VINB+ 6 CSB MCP665 3x3 DFN * VOUTA VINA– VINA+ VSS CSA 1 2 3 4 5 10 VDD 9 8 7 6 VOUTB VINB– VINB+ CSB * Includes Exposed Thermal Pad (EP); see Table 3-1. © 2009 Microchip Technology Inc. DS22194A-page 1 MCP661/2/3/5 NOTES: DS22194A-page 2 © 2009 Microchip Technology Inc. MCP661/2/3/5 1.0 ELECTRICAL CHARACTERISTICS 1.1 Absolute Maximum Ratings † † Notice: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. VDD – VSS .......................................................................6.5V Current at Input Pins ....................................................±2 mA Analog Inputs (VIN+ and VIN–) †† . VSS – 1.0V to VDD + 1.0V All other Inputs and Outputs .......... VSS – 0.3V to VDD + 0.3V Output Short Circuit Current ................................ Continuous Current at Output and Supply Pins ..........................±150 mA Storage Temperature ...................................-65°C to +150°C Max. Junction Temperature ........................................ +150°C ESD protection on all pins (HBM, MM) ................≥ 1 kV, 200V 1.2 †† See Section 4.1.2 “Input Voltage and Current Limits”. Specifications TABLE 1-1: DC ELECTRICAL SPECIFICATIONS Electrical Characteristics: Unless otherwise indicated, TA = +25°C, VDD = +2.5V to +5.5V, VSS = GND, VCM = VDD/3, VOUT ≈ VDD/2, VL = VDD/2, RL = 1 kΩ to VL and CS = VSS (refer to Figure 1-2). Parameters Sym Min Typ Max Units Conditions Input Offset Input Offset Voltage Input Offset Voltage Drift Power Supply Rejection Ratio VOS -8 ±1.8 +8 ΔVOS/ΔTA — ±2.0 — PSRR 61 76 — mV µV/°C TA= -40°C to +125°C dB Input Current and Impedance IB — 6 — pA Across Temperature IB — 130 — pA TA= +85°C Across Temperature IB — 1700 5,000 pA TA= +125°C IOS — ±10 — pA 13 Input Bias Current Input Offset Current Common Mode Input Impedance ZCM — 10 ||9 — Ω||pF Differential Input Impedance ZDIFF — 1013||2 — Ω||pF Common-Mode Input Voltage Range VCMR VSS − 0.3 — VDD − 1.3 V (Note 1) Common-Mode Rejection Ratio CMRR 64 79 — dB VDD = 2.5V, VCM = -0.3 to 1.2V CMRR 66 81 — dB VDD = 5.5V, VCM = -0.3 to 4.2V AOL 88 117 — dB VDD = 2.5V, VOUT = 0.3V to 2.2V AOL 94 126 — dB VDD = 5.5V, VOUT = 0.3V to 5.2V VOL, VOH VSS + 25 — VDD − 25 mV VDD = 2.5V, G = +2, 0.5V Input Overdrive VOL, VOH VSS + 50 — VDD − 50 mV VDD = 5.5V, G = +2, 0.5V Input Overdrive ISC ±45 ±90 ±145 mA VDD = 2.5V (Note 2) ISC ±40 ±80 ±150 mA VDD = 5.5V (Note 2) VDD 2.5 — 5.5 V IQ 3 6 9 mA Common Mode Open Loop Gain DC Open Loop Gain (large signal) Output Maximum Output Voltage Swing Output Short Circuit Current Power Supply Supply Voltage Quiescent Current per Amplifier Note 1: 2: No Load Current See Figure 2-5 for temperature effects. The ISC specifications are for design guidance only; they are not tested. © 2009 Microchip Technology Inc. DS22194A-page 3 MCP661/2/3/5 TABLE 1-2: AC ELECTRICAL SPECIFICATIONS Electrical Characteristics: Unless otherwise indicated, TA = +25°C, VDD = +2.5V to +5.5V, VSS = GND, VCM = VDD/2, VOUT ≈ VDD/2, VL = VDD/2, RL = 1 kΩ to VL, CL = 20 pF and CS = VSS (refer to Figure 1-2). Parameters Sym Min Typ Max Units Conditions GBWP — 60 — MHz PM — 65 — ° ROUT — 10 — Ω THD+N — 0.003 — % G = +1, VOUT = 2VP-P, f = 1 kHz, VDD = 5.5V, BW = 80 kHz Differential Gain, Positive Video (Note 1) DG — 0.3 — % NTSC, VDD = +2.5V, VSS = -2.5V, G = +2, VL = 0V, DC VIN = 0V to 0.7V Differential Gain, Negative Video (Note 1) DG — 0.3 — % NTSC, VDD = +2.5V, VSS = -2.5V, G = +2, VL = 0V, DC VIN = 0V to -0.7V Differential Phase, Positive Video (Note 1) DP — 0.3 — ° NTSC, VDD = +2.5V, VSS = -2.5V, G = +2, VL = 0V, DC VIN = 0V to 0.7V Differential Phase, Negative Video (Note 1) DP — 0.9 — ° NTSC, VDD = +2.5V, VSS = -2.5V, G = +2, VL = 0V, DC VIN = 0V to -0.7V AC Response Gain Bandwidth Product Phase Margin Open Loop Output Impedance G = +1 AC Distortion Total Harmonic Distortion plus Noise Step Response tr — 5 — ns SR — 32 — V/µs G = +1 Input Noise Voltage Eni — 14 — µVP-P f = 0.1 Hz to 10 Hz Input Noise Voltage Density eni — 6.8 — nV/√Hz f = 1 MHz Input Noise Current Density ini 4 — fA/√Hz f = 1 kHz Rise Time, 10% to 90% Slew Rate G = +1, VOUT = 100 mVP-P Noise Note 1: These specifications are described in detail in Section 4.3 “Distortion”. TABLE 1-3: DIGITAL ELECTRICAL SPECIFICATIONS Electrical Characteristics: Unless otherwise indicated, TA = +25°C, VDD = +2.5V to +5.5V, VSS = GND, VCM = VDD/2, VOUT ≈ VDD/2, VL = VDD/2, RL = 1 kΩ to VL, CL = 20 pF and CS = VSS (refer to Figure 1-1 and Figure 1-2). Parameters Sym Min Typ Max Units CS Logic Threshold, Low VIL VSS — 0.2VDD V CS Input Current, Low ICSL — -0.1 — nA CS Logic Threshold, High VIH 0.8VDD VDD V CS Input Current, High ICSH — -0.7 — µA ISS -2 -1 — µA Conditions CS Low Specifications CS = 0V CS High Specifications GND Current CS Internal Pull Down Resistor CS = VDD RPD — 5 — MΩ IO(LEAK) — 40 — nA VHYST — 0.25 — V CS High to Amplifier Off Time (output goes High-Z) tOFF — 200 — ns G = +1 V/V, VL = VSS CS = 0.8VDD to VOUT = 0.1(VDD/2) CS Low to Amplifier On Time tON — 2 10 µs G = +1 V/V, VL = VSS, CS = 0.2VDD to VOUT = 0.9(VDD/2) Amplifier Output Leakage CS = VDD, TA = +125°C CS Dynamic Specifications CS Input Hysteresis DS22194A-page 4 © 2009 Microchip Technology Inc. MCP661/2/3/5 TABLE 1-4: TEMPERATURE SPECIFICATIONS Electrical Characteristics: Unless otherwise indicated, all limits are specified for: VDD = +2.5V to +5.5V, VSS = GND. Parameters Sym Min Typ Max Units Specified Temperature Range TA -40 — +125 °C Operating Temperature Range TA -40 — +125 °C Storage Temperature Range TA -65 — +150 °C Conditions Temperature Ranges (Note 1) Thermal Package Resistances Thermal Resistance, 8L-3x3 DFN θJA — 60 — °C/W Thermal Resistance, 8L-SOIC θJA — 149.5 — °C/W Thermal Resistance, 10L-3x3 DFN θJA — 57 — °C/W Thermal Resistance, 10L-MSOP θJA — 202 — °C/W (Note 2) Operation must not cause TJ to exceed Maximum Junction Temperature specification (150°C). Measured on a standard JC51-7, four layer printed circuit board with ground plane and vias. Note 1: 2: 1.3 (Note 2) Timing Diagram EQUATION 1-1: G DM = R F ⁄ R G ICS 0 nA (typical) 1 µA (typical) VIH VIL CS tON VOUT ISS 1.4 V CM = ( V P + V DD ⁄ 2 ) ⁄ 2 V OST = V IN– – V IN+ V OUT = ( V DD ⁄ 2 ) + ( V P – V M ) + V OST ( 1 + G DM ) Where: tOFF High-Z High-Z On -6 mA (typical) -1 µA (typical) FIGURE 1-1: 1 µA (typical) -1 µA (typical) GDM = Differential Mode Gain (V/V) VCM = Op Amp’s Common Mode Input Voltage (V) VOST = Op Amp’s Total Input Offset Voltage (mV) CF 6.8 pF Timing Diagram. Test Circuits The circuit used for most DC and AC tests is shown in Figure 1-2. This circuit can independently set VCM and VOUT; see Equation 1-1. Note that VCM is not the circuit’s common mode voltage ((VP + VM)/2), and that VOST includes VOS plus the effects (on the input offset error, VOST) of temperature, CMRR, PSRR and AOL. RG 10 kΩ RF 10 kΩ VP VDD VIN+ CB1 100 nF MCP66X VDD/2 CB2 2.2 µF VIN– VM RG 10 kΩ RL 1 kΩ RF 10 kΩ CF 6.8 pF VOUT CL 20 pF VL FIGURE 1-2: AC and DC Test Circuit for Most Specifications. © 2009 Microchip Technology Inc. DS22194A-page 5 MCP661/2/3/5 NOTES: DS22194A-page 6 © 2009 Microchip Technology Inc. MCP661/2/3/5 2.0 TYPICAL PERFORMANCE CURVES Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. Note: Unless otherwise indicated, TA = +25°C, VDD = +2.5V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 1 kΩ to VL, CL = 20 pF and CS = VSS. DC Signal Inputs 22% 20% 18% 16% 14% 12% 10% 8% 6% 4% 2% 0% 1.4 100 Samples TA = +25°C VDD = 2.5V and 5.5V Input Offset Voltage (mV) Percentage of Occurrences 2.1 FIGURE 2-1: VDD = 5.5V 1.1 1.0 0.9 0.8 VDD = 2.5V 0.7 4 5 6 Input Offset Voltage. 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 Output Voltage (V) FIGURE 2-4: Output Voltage. 0.0 100 Samples VDD = 2.5V and 5.5V TA = -40°C to +125°C Low Input Common Mode Headroom (V) Percentage of Occurrences 1.2 0.6 -6 -5 -4 -3 -2 -1 0 1 2 3 Input Offset Voltage (mV) 24% 22% 20% 18% 16% 14% 12% 10% 8% 6% 4% 2% 0% Representative Part 1.3 1 Lot Low (VCMR_L – VSS) -0.1 -0.2 VDD = 2.5V -0.3 VDD = 5.5V -0.4 -0.5 -12 -10 -8 -6 -4 -2 0 2 4 6 8 10 12 -50 -25 Input Offset Voltage Drift (µV/°C) Input Offset Voltage Drift. 1.4 Representative Part VCM = VSS +125°C +85°C +25°C -40°C 0 25 50 75 100 Ambient Temperature (°C) 125 FIGURE 2-5: Low Input Common Mode Voltage Headroom vs. Ambient Temperature. High Input Common Mode Headroom (V) Input Offset Voltage (mV) FIGURE 2-2: 0.0 -0.2 -0.4 -0.6 -0.8 -1.0 -1.2 -1.4 -1.6 -1.8 -2.0 Input Offset Voltage vs. 1 Lot High (VDD – VCMR_H) 1.3 VDD = 2.5V 1.2 1.1 VDD = 5.5V 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 Power Supply Voltage (V) FIGURE 2-3: Input Offset Voltage vs. Power Supply Voltage with VCM = 0V. © 2009 Microchip Technology Inc. -50 -25 0 25 50 75 100 Ambient Temperature (°C) 125 FIGURE 2-6: High Input Common Mode Voltage Headroom vs. Ambient Temperature. DS22194A-page 7 MCP661/2/3/5 Note: Unless otherwise indicated, TA = +25°C, VDD = +2.5V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 1 kΩ to VL, CL = 20 pF and CS = VSS. 1.5 130 VDD = 2.5V Representative Part 1.0 DC Open-Loop Gain (dB) Input Offset Voltage (mV) 2.0 -40°C +25°C +85°C +125° C 0.5 0.0 -0.5 -1.0 -1.5 115 105 -50 1.5 0 25 50 75 Ambient Temperature (°C) 130 VDD = 5.5V Representative Part 1.0 0.5 +125° C +85°C +25°C 40°C 0.0 -0.5 -1.0 -1.5 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 -0.5 -2.0 Input Common Mode Voltage (V) 125 VDD = 5.5V 120 115 VDD = 2.5V 110 105 100 95 100 1.E+02 Input Bias, Offset Currents (pA) 1.E-08 10n 110 105 100 95 90 85 80 75 70 65 100 125 1k 10k 1.E+03 1.E+04 Load Resistance (Ω) FIGURE 2-11: Load Resistance. FIGURE 2-8: Input Offset Voltage vs. Common Mode Voltage with VDD = 5.5V. CMRR, PSRR (dB) -25 FIGURE 2-10: DC Open-Loop Gain vs. Ambient Temperature. DC Open-Loop Gain (dB) Input Offset Voltage (mV) 2.0 VDD = 2.5V 110 Input Common Mode Voltage (V) FIGURE 2-7: Input Offset Voltage vs. Common Mode Voltage with VDD = 2.5V. VDD = 5.5V 120 100 3.0 2.5 2.0 1.5 1.0 0.5 -0.5 0.0 -2.0 125 100k 1.E+05 DC Open-Loop Gain vs. VDD = 5.5V VCM = VCMR_H 1n 1.E-09 PSRR 100p 1.E-10 CMRR, VDD = 2.5V CMRR, VDD = 5.5V IB 10p 1.E-11 60 | IOS | 1p 1.E-12 -50 -25 0 25 50 75 Ambient Temperature (°C) 100 FIGURE 2-9: CMRR and PSRR vs. Ambient Temperature. DS22194A-page 8 125 25 45 65 85 105 Ambient Temperature (°C) 125 FIGURE 2-12: Input Bias and Offset Currents vs. Ambient Temperature with VDD = +5.5V. © 2009 Microchip Technology Inc. MCP661/2/3/5 Note: Unless otherwise indicated, TA = +25°C, VDD = +2.5V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 1 kΩ to VL, CL = 20 pF and CS = VSS. 1000 Input Bias, Offset Currents (pA) Input Current Magnitude (A) 1.E-03 1m 100µ 1.E-04 10µ 1.E-05 1µ 1.E-06 100n 1.E-07 10n 1.E-08 1n 1.E-09 100p 1.E-10 +125°C +85°C +25°C -40°C 10p 1.E-11 1p 1.E-12 600 Representative Part TA = +125°C VDD = 5.5V 400 200 0 IOS -200 FIGURE 2-13: Input Bias Current vs. Input Voltage (below VSS). 60 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 -400 -1.0 -0.9 -0.8 -0.7 -0.6 -0.5 -0.4 -0.3 -0.2 -0.1 0.0 Input Voltage (V) Input Bias, Offset Currents (pA) IB 800 Common Mode Input Voltage (V) FIGURE 2-15: Input Bias and Offset Currents vs. Common Mode Input Voltage with TA = +125°C. IB 40 20 0 IOS -20 -40 -60 -80 -100 Representative Part TA = +85°C VDD = 5.5V 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 -120 Common Mode Input Voltage (V) FIGURE 2-14: Input Bias and Offset Currents vs. Common Mode Input Voltage with TA = +85°C. © 2009 Microchip Technology Inc. DS22194A-page 9 MCP661/2/3/5 Note: Unless otherwise indicated, TA = +25°C, VDD = +2.5V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 1 kΩ to VL, CL = 20 pF and CS = VSS. Other DC Voltages and Currents 9 8 Supply Current (mA/amplifier) VDD = 5.5V 100 VDD = 2.5V VOL – VSS 10 6.5 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 FIGURE 2-19: Supply Voltage. Supply Current vs. Power 6 Supply Current (mA/amplifier) VDD = 5.5V 20 15 10 VDD = 5.5V 5 VDD = 2.5V 4 3 2 1 VDD – VOH FIGURE 2-17: Output Voltage Headroom vs. Ambient Temperature. 100 80 60 40 20 0 -20 -40 -60 -80 -100 6.0 5.5 5.0 4.5 4.0 125 3.5 100 3.0 0 25 50 75 Ambient Temperature (°C) 2.5 -25 2.0 -50 1.5 0 0 1.0 VDD = 2.5V -0.5 Output Headroom (mV) Power Supply Voltage (V) VOL – VSS 25 Common Mode Input Voltage (V) FIGURE 2-20: Supply Current vs. Common Mode Input Voltage. 6.5 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 +125°C +85°C +25°C -40°C 0.0 Output Short Circuit Current (mA) 2 7 35 5 +125°C +85°C +25°C -40°C 3 100 RL = 1 kΩ 30 4 0.0 1 10 Output Current Magnitude (mA) FIGURE 2-16: Output Voltage Headroom vs. Output Current. 40 5 0 1 45 6 1 VDD – VOH 0.1 7 0.5 Output Voltage Headroom (mV) 1000 0.0 2.2 Power Supply Voltage (V) FIGURE 2-18: Output Short Circuit Current vs. Power Supply Voltage. DS22194A-page 10 © 2009 Microchip Technology Inc. MCP661/2/3/5 Note: Unless otherwise indicated, TA = +25°C, VDD = +2.5V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 1 kΩ to VL, CL = 20 pF and CS = VSS. 80 80 90 75 75 Gain Bandwidth Product (MHz) 100 80 70 60 50 CMRR PSRR+ PSRR- 30 20 65 VDD = 5.5V VDD = 2.5V 60 60 55 55 50 50 GBWP 45 45 FIGURE 2-21: Frequency. 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 10M 1.E+7 1.5 1M 1.E+6 1.0 10k 100k 1.E+4 1.E+5 Frequency (Hz) 0.5 1k 1.E+3 0.0 100 1.E+2 40 -0.5 40 10 Common Mode Input Voltage (V) FIGURE 2-24: Gain Bandwidth Product and Phase Margin vs. Common Mode Input Voltage. CMRR and PSRR vs. 80 80 120 -30 75 75 100 -60 ∠AOL 80 -90 60 -120 40 -150 | AOL | 20 -180 0 -20 -210 70 80 75 75 70 60 55 65 VDD = 5.5V VDD = 2.5V 60 55 50 50 GBWP 45 40 -50 -25 0 25 50 75 100 Ambient Temperature (°C) 45 40 125 FIGURE 2-23: Gain Bandwidth Product and Phase Margin vs. Ambient Temperature. © 2009 Microchip Technology Inc. 55 50 50 GBWP 45 45 40 FIGURE 2-25: Gain Bandwidth Product and Phase Margin vs. Output Voltage. 80 65 60 55 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 Output Voltage (V) Open-Loop Gain vs. PM 65 VDD = 5.5V VDD = 2.5V 60 40 -240 70 70 PM 65 1 1.E+ 10 1.E+ 100 1.E+ 1k 10k 1M 10M 1G 1.E+ 1.E+ 100k 1.E+ 1.E+ 1.E+ 100M 1.E+ 1.E+ 0 1 2 3 4 5 (Hz) 6 7 8 9 Frequency FIGURE 2-22: Frequency. Gain Bandwidth Product (MHz) Gain Bandwidth Product (MHz) 0 Open-Loop Phase (°) 140 Phase Margin (°) Open-Loop Gain (dB) 70 PM 65 Phase Margin (°) 40 70 Phase Margin (°) Frequency Response Closed-Loop Output Impedance (Ω) CMRR, PSRR (dB) 2.3 100 10 G = 101 V/V G = 11 V/V G = 1 V/V 1 0.1 10k 1.0E+04 100k 1.0E+05 1M 10M 1.0E+06 1.0E+07 Frequency (Hz) 100M 1.0E+08 FIGURE 2-26: Closed-Loop Output Impedance vs. Frequency. DS22194A-page 11 MCP661/2/3/5 Note: Unless otherwise indicated, TA = +25°C, VDD = +2.5V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, 10 150 9 140 8 130 7 6 5 GN = 1 V/V GN = 2 V/V GN ≥ 4 V/V 4 3 2 1 0 10p 1.0E-11 Channel-to-Channel Separation; RTI (dB) Gain Peaking (dB) VL = VDD/2, RL = 1 kΩ to VL, CL = 20 pF and CS = VSS. FIGURE 2-27: Gain Peaking vs. Normalized Capacitive Load. DS22194A-page 12 VCM = VDD/2 G = +1 V/V 120 110 100 90 80 70 60 100p 1n 1.0E-10 1.0E-09 Normalized Capacitive Load; CL/GN (F) RS = 0Ω RS = 100Ω RS = 1 kΩ RS = 10 kΩ RS = 100 kΩ 50 1k 1.E+03 10k 1.E+04 100k 1M 1.E+05 1.E+06 Frequency (Hz) 10M 1.E+07 FIGURE 2-28: Channel-to-Channel Separation vs. Frequency. © 2009 Microchip Technology Inc. MCP661/2/3/5 Note: Unless otherwise indicated, TA = +25°C, VDD = +2.5V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 1 kΩ to VL, CL = 20 pF and CS = VSS. Noise and Distortion 1.E+4 10µ Input Noise; eni(t) (µV) 20 1.E+3 1µ 1.E+2 100n 1.E+1 10n 1 1.E+0 10 1.E+1 100 1.E+2 10 5 0 -5 -10 Analog NPBW = 0.1 Hz Sample Rate = 2 SPS VOS = -953 µV -15 0 100k 10M 1M 1.E+7 1.E+5 1.E+6 10k 1.E+4 Input Noise Voltage Density THD + Noise (%) VDD = 2.5V VDD = 5.5V 5 10 15 20 25 30 35 40 45 50 55 60 65 Time (min) FIGURE 2-32: 0.1 Hz Filter. 1 VDD = 5.0V VOUT = 2 VP-P 0.1 0.01 0.001 BW = 22 Hz to 80 kHz 0.0001 100 1.E+2 Change in Gain Magnitude (%) VDD = 2.5V VDD = 5.5V 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 -0.5 f = 1 MHz Common Mode Input Voltage (V) FIGURE 2-31: Input Noise Voltage Density vs. Input Common Mode Voltage with f = 1 MHz. © 2009 Microchip Technology Inc. FIGURE 2-33: 1k 1.E+3 10k 1.E+4 Frequency (Hz) 100k 1.E+5 THD+N vs. Frequency. 0.2 0.2 Positive Video Negative Video 0.1 0.1 0.0 0.0 -0.1 -0.1 -0.2 -0.2 -0.3 -0.3 Δ(|G|) Representative Part -0.4 -0.4 VDD = 2.5V -0.5 -0.5 VSS = -2.5V -0.6 -0.6 VL = 0V -0.7 -0.7 RL = 150Ω -0.8 -0.8 Normalized to DC VIN = 0V NTSC -0.9 -0.9 Δ(∠G) -1.0 -1.0 -0.8 -0.6 -0.4 -0.2 0.0 0.2 0.4 0.6 0.8 DC Input Voltage (V) Change in Gain Phase (°) 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 1.5 1.0 0.5 0.0 FIGURE 2-30: Input Noise Voltage Density vs. Input Common Mode Voltage with f = 100 Hz. Input Noise Voltage Density (nV/√Hz) G = 1 V/V G = 11 V/V BW = 22 Hz to > 500 kHz Common Mode Input Voltage (V) 20 18 16 14 12 10 8 6 4 2 0 Input Noise vs. Time with f = 100 Hz -0.5 Input Noise Voltage Density (nV/√Hz) 1k 1.E+3 Frequency (Hz) FIGURE 2-29: vs. Frequency. 200 180 160 140 120 100 80 60 40 20 0 Representative Part 15 -20 1n 1.E+0 0.1 1.E-1 2.0 Input Noise Voltage Density (V/√Hz) 2.4 FIGURE 2-34: Change in Gain Magnitude and Phase vs. DC Input Voltage. DS22194A-page 13 MCP661/2/3/5 Note: Unless otherwise indicated, TA = +25°C, VDD = +2.5V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 1 kΩ to VL, CL = 20 pF and CS = VSS. 2.5 Time Response VIN 0 Output Voltage (V) Output Voltage (10 mV/div) VDD = 5.5V G=1 VOUT 20 40 60 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 80 100 120 140 160 180 200 Time (ns) Non-inverting Small Signal VOUT 100 200 FIGURE 2-38: Response. 300 400 Time (ns) 500 Input, Output Voltages (V) VOUT 600 Inverting Large Signal Step VDD = 5.5V G=2 6 VOUT 5 VIN 4 3 2 1 0 -1 0 100 FIGURE 2-36: Step Response. 200 300 400 500 Time (ns) 600 700 800 Non-inverting Large Signal 0 Output Voltage (10 mV/div) VDD = 5.5V G = -1 RF = 402Ω VOUT 50 100 150 200 250 300 350 400 450 500 Time (ns) FIGURE 2-37: Response. DS22194A-page 14 Inverting Small Signal Step 1 2 3 4 5 6 Time (µs) 7 8 9 10 FIGURE 2-39: The MCP661/2/3/5 family shows no input phase reversal with overdrive. VIN 0 VIN 7 VDD = 5.5V G=1 VIN VDD = 5.5V G = -1 RF = 402Ω 0 Slew Rate (V/µs) Output Voltage (V) FIGURE 2-35: Step Response. 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 50 45 40 35 30 25 20 15 10 5 0 Falling Edge VDD = 5.5V VDD = 2.5V Rising Edge -50 -25 FIGURE 2-40: Temperature. 0 25 50 75 Ambient Temperature (°C) 100 125 Slew Rate vs. Ambient © 2009 Microchip Technology Inc. MCP661/2/3/5 Note: Unless otherwise indicated, TA = +25°C, VDD = +2.5V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 1 kΩ to VL, CL = 20 pF and CS = VSS. Maximum Output Voltage Swing (VP-P) 10 VDD = 5.5V VDD = 2.5V 1 0.1 100k 1.E+05 1M 10M 1.E+06 1.E+07 Frequency (Hz) 100M 1.E+08 FIGURE 2-41: Maximum Output Voltage Swing vs. Frequency. © 2009 Microchip Technology Inc. DS22194A-page 15 MCP661/2/3/5 Note: Unless otherwise indicated, TA = +25°C, VDD = +2.5V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 1 kΩ to VL, CL = 20 pF and CS = VSS. Chip Select Response 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0.40 CS = VDD 0.35 CS Hysteresis (V) CS Current (µA) 2.6 0.30 0.20 0.10 0.05 0.00 FIGURE 2-42: Supply Voltage. -50 CS 2.0 1.5 VOUT 1.0 On 0.5 0.0 Off 100 125 CS Hysteresis vs. Ambient 4 3 VDD = 2.5V 2 1 VDD = 5.5V Off 0 -0.5 0 2 4 6 8 10 12 Time (µs) 14 16 18 20 FIGURE 2-43: CS and Output Voltages vs. Time with VDD = 2.5V. 6 4 3 VOUT 2 On 1 -25 Off Off 0 25 50 75 Ambient Temperature (°C) 100 125 FIGURE 2-46: CS Turn On Time vs. Ambient Temperature. CS Pull-down Resistor (MΩ) 5 -50 8 VDD = 5.5V G=1 VL = 0V CS 0 0 25 50 75 Ambient Temperature (°C) 5 VDD = 2.5V G=1 VL = 0V CS Turn On Time (µs) 2.5 -25 FIGURE 2-45: Temperature. CS Current vs. Power 3.0 CS, VOUT (V) VDD = 2.5V 0.15 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 Power Supply Voltage (V) CS, VOUT (V) VDD = 5.5V 0.25 Representative Part 7 6 5 4 3 2 1 0 -1 0 1 2 3 4 5 6 Time (µs) 7 8 9 10 FIGURE 2-44: CS and Output Voltages vs. Time with VDD = 5.5V. DS22194A-page 16 -50 -25 0 25 50 75 Ambient Temperature (°C) 100 125 FIGURE 2-47: CS’s Pull-down Resistor (RPD) vs. Ambient Temperature. © 2009 Microchip Technology Inc. MCP661/2/3/5 Note: Unless otherwise indicated, TA = +25°C, VDD = +2.5V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, CS = VDD 1.E-06 1µ Output Leakage Current (A) 0.0 -0.2 -0.4 -0.6 -0.8 -1.0 -1.2 -1.4 -1.6 -1.8 -2.0 CS = VDD = 5.5V 100n 1.E-07 10n 1.E-08 1n 1.E-09 +125°C +85°C Power Supply Voltage (V) FIGURE 2-48: Quiescent Current in Shutdown vs. Power Supply Voltage. © 2009 Microchip Technology Inc. 6.5 6.0 5.5 5.0 4.5 4.0 3.5 100p 1.E-10 3.0 2.5 2.0 1.5 1.0 0.5 +125°C +85°C +25°C -40°C 0.0 Negative Power Supply Current; ISS (µA) VL = VDD/2, RL = 1 kΩ to VL, CL = 20 pF and CS = VSS. +25°C 10p 1.E-11 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 Output Voltage (V) FIGURE 2-49: Output Voltage. Output Leakage Current vs. DS22194A-page 17 MCP661/2/3/5 NOTES: DS22194A-page 18 © 2009 Microchip Technology Inc. MCP661/2/3/5 3.0 PIN DESCRIPTIONS Descriptions of the pins are listed in Table 3-1. TABLE 3-1: MCP661 PIN FUNCTION TABLE MCP662 MCP663 MCP665 Symbol Description SOIC SOIC DFN SOIC MSOP DFN 6 2 3 4 1 2 3 4 1 2 3 4 6 2 3 4 1 2 3 4 1 2 3 4 VOUT, VOUTA VIN–, VINA– VIN+, VINA+ VSS — — — 8 5 5 CS, CSA Chip Select Digital Input (op amp A) — — — — 7 1,5,8 — — 5 6 7 8 — — — 5 6 7 8 — 9 — — — — 7 1,5 — 6 7 8 9 10 — — 6 7 8 9 10 — 11 CSB VINB+ VINB– VOUTB VDD NC EP Chip Select Digital Input (op amp B) Non-inverting Input (op amp B) Inverting Input (op amp B) Output (op amp B) Positive Power Supply No Internal Connection Exposed Thermal Pad (EP); must be connected to VSS 3.1 Analog Outputs 3.4 Output (op amp A) Inverting Input (op amp A) Non-inverting Input (op amp A) Negative Power Supply Chip Select Digital Input (CS) The analog output pins (VOUT) are low-impedance voltage sources. This input (CS) is a CMOS, Schmitt-triggered input that places the part into a low power mode of operation. 3.2 3.5 Analog Inputs Exposed Thermal Pad (EP) The non-inverting and inverting inputs (VIN+, VIN–, …) are high-impedance CMOS inputs with low bias currents. There is an internal connection between the Exposed Thermal Pad (EP) and the VSS pin; they must be connected to the same potential on the Printed Circuit Board (PCB). 3.3 This pad can be connected to a PCB ground plane to provide a larger heat sink. This improves the package thermal resistance (θJA). Power Supply Pins The positive power supply (VDD) is 2.5V to 5.5V higher than the negative power supply (VSS). For normal operation, the other pins are between VSS and VDD. Typically, these parts are used in a single (positive) supply configuration. In this case, VSS is connected to ground and VDD is connected to the supply. VDD will need bypass capacitors. © 2009 Microchip Technology Inc. DS22194A-page 19 MCP661/2/3/5 NOTES: DS22194A-page 20 © 2009 Microchip Technology Inc. MCP661/2/3/5 4.0 APPLICATIONS VDD The MCP661/2/3/5 family op amps is manufactured using Microchip’s state of the art CMOS process. It is designed for low cost, low power and high speed applications. Its low supply voltage, low quiescent current and wide bandwidth make the MCP661/2/3/5 ideal for battery-powered applications. 4.1 V1 V2 Input 4.1.1 INPUT VOLTAGE AND CURRENT LIMITS The ESD protection on the inputs can be depicted as shown in Figure 4-1. This structure was chosen to protect the input transistors, and to minimize input bias current (IB). The input ESD diodes clamp the inputs when they try to go more than one diode drop below VSS. They also clamp any voltages that go too far above VDD; their breakdown voltage is high enough to allow normal operation, and low enough to bypass quick ESD events within the specified limits. Input Stage Bond V – IN Pad VOUT R2 FIGURE 4-2: Inputs. Protecting the Analog It is also possible to connect the diodes to the left of the resistor R1 and R2. In this case, the currents through the diodes D1 and D2 need to be limited by some other mechanism. The resistors then serve as in-rush current limiters; the DC current into the input pins (VIN+ and VIN–) should be very small. A significant amount of current can flow out of the inputs (through the ESD diodes) when the common mode voltage (VCM) is below ground (VSS); see Figure 2-13. Applications that are high impedance may need to limit the usable voltage range. NORMAL OPERATION The input stage of the MCP661/2/3/5 op amps uses a differential PMOS input stage. It operates at low common mode input voltages (VCM), with VCM between VSS – 0.3V and VDD – 1.3V. To ensure proper operation, the input offset voltage (VOS) is measured at both VCM = VSS – 0.3V and VDD – 1.3V. See Figure 2-5 and Figure 2-6 for temperature effects. When operating at very low non-inverting gains, the output voltage is limited at the top by the VCM range (< VDD – 1.3V); see Figure 4-3. VSS Bond Pad FIGURE 4-1: Structures. MCP66X VSS – (minimum expected V1) 2 mA VSS – (minimum expected V2) R2 > 2 mA 4.1.3 VDD Bond Pad VIN+ Bond Pad D2 R1 > PHASE REVERSAL The input devices are designed to not exhibit phase inversion when the input pins exceed the supply voltages. Figure 2-39 shows an input voltage exceeding both supplies with no phase inversion. 4.1.2 D1 R1 Simplified Analog Input ESD In order to prevent damage and/or improper operation of these amplifiers, the circuit must limit the currents (and voltages) at the input pins (see Section 1.1 “Absolute Maximum Ratings †”). Figure 4-2 shows the recommended approach to protecting these inputs. The internal ESD diodes prevent the input pins (VIN+ and VIN–) from going too far below ground, and the resistors R1 and R2 limit the possible current drawn out of the input pins. Diodes D1 and D2 prevent the input pins (VIN+ and VIN–) from going too far above VDD, and dump any currents onto VDD. When implemented as shown, resistors R1 and R2 also limit the current through D1 and D2. © 2009 Microchip Technology Inc. VDD VIN MCP66X VOUT V SS < V IN, V OUT ≤ V DD – 1.3V FIGURE 4-3: Unity Gain Voltage Limitations for Linear Operation. DS22194A-page 21 MCP661/2/3/5 4.2 Rail-to-Rail Output 4.2.1 VDD MAXIMUM OUTPUT VOLTAGE 4.2.2 VOH Limited +ISC Limited -ISC Limited RL = 100Ω RL = 10Ω VLG VSS FIGURE 4-5: Calculations. Diagram for Power PRSER(t) = IOUT2RSER PL(t) = IL2RL 120 100 80 60 40 0 20 -20 -40 -60 -80 -100 -120 RL POA(t) = IDD (VDD – VOUT) + ISS (VSS – VOUT) VOL Limited IOUT (mA) Output Current. POWER DISSIPATION Since the output short circuit current (ISC) is specified at ±90 mA (typical), these op amps are capable of both delivering and dissipating significant power. Figure 4-5 show the quantities used in the following power calculations for a single op amp. RSER is 0 Ω in most applications; it can be used to limit IOUT. VOUT is the op amp’s output voltage, VL is the voltage at the load, and VLG is the load’s ground point. VSS is usually ground (0V). The input currents are assumed to be negligible. The currents shown are approximately: The maximum op amp power, for resistive loads, occurs when VOUT is halfway between VDD and VLG or halfway between VSS and VLG: EQUATION 4-3: POAmax ≤ max2(VDD – VLG , VLG – VSS) 4(RSER + RL) The maximum ambient to junction temperature rise (ΔTJA) and junction temperature (TJ) can be calculated using POAmax, ambient temperature (TA), the package thermal resistance (θJA) found in Table 1-4, and the number of op amps in the package (assuming equal power dissipations): EQUATION 4-4: ΔTJA = POA(t) θJA ≤ n POAmaxθJA TJ = TA + ΔTJA EQUATION 4-1: IOUT = IL = IL EQUATION 4-2: RL = 1 kΩ 4.2.3 VL MCP66X The instantaneous op amp power (POA(t)), RSER power (PRSER(t)) and load power (PL(t)) are: (VDD = 5.5V) FIGURE 4-4: RSER ISS Figure 4-4 shows the possible combinations of output voltage (VOUT) and output current (IOUT), when VDD = 5.5V. IOUT is positive when it flows out of the op amp into the external circuit. VOUT (V) IOUT OUTPUT CURRENT 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 -0.5 VOUT IDD The Maximum Output Voltage (see Figure 2-16 and Figure 2-17) describes the output range for a given load. For instance, the output voltage swings to within 50 mV of the negative rail with a 1 kΩ load tied to VDD/2. VOUT – VLG RSER + RL IDD ≈ IQ + max(0, IOUT) Where: n = number of op amps in package (1, 2) ISS ≈ –IQ + min(0, IOUT) Where: IQ = quiescent supply current DS22194A-page 22 © 2009 Microchip Technology Inc. MCP661/2/3/5 The power de-rating across temperature for an op amp in a particular package can be easily calculated (assuming equal power dissipations): EQUATION 4-5: T – TA POAmax ≤ Jmax n θJA When driving large capacitive loads with these op amps (e.g., > 20 pF when G = +1), a small series resistor at the output (RISO in Figure 4-6) improves the feedback loop’s phase margin (stability) by making the output load resistive at higher frequencies. The bandwidth will be generally lower than the bandwidth with no capacitive load. Where: RG TJmax = • Lower θJA - Use another package - PCB layout (ground plane, etc.) - Heat sinks and air flow • Reduce POAmax - Increase RL - Limit IOUT (using RSER) - Decrease VDD VOUT DG is the peak-to-peak change in the AC gain magnitude (color hue), as the DC level (luminance) is changed, in units of %. DP is the peak-to-peak change in the AC gain phase (color saturation), as the DC level (luminance) is changed, in units of °. 4.4.1 RN Improving Stability CAPACITIVE LOADS MCP66X FIGURE 4-6: Output Resistor, RISO stabilizes large capacitive loads. Figure 4-7 gives recommended RISO values for different capacitive loads and gains. The x-axis is the normalized load capacitance (CL/GN), where GN is the circuit’s noise gain. For non-inverting gains, GN and the Signal Gain are equal. For inverting gains, GN is 1+|Signal Gain| (e.g., -1 V/V gives GN = +2 V/V). Distortion 100 Recommended RISO (Ω) Differential Gain (DG) and Differential Phase (DP) refer to the non-linear distortion produced by a NTSC (or PAL) video component. Table 1-2 and Figure 2-34 show the typical performance of the MCP661, configured as a gain of +2 amplifier (see Figure 4-10), when driving one back-matched video load (150Ω, for 75Ω cable). Our tests use a sine wave at NTSC’s color sub-carrier frequency of 3.58 MHz, with a 0.286VP-P magnitude. The DC input voltage is changed over a +0.7V range (positive video) or a -0.7V range (negative video). 4.4 RISO CL Several techniques are available to reduce ΔTJA for a given POAmax: 4.3 RF absolute max. junction temperature 10 GN = +1 GN ≥ +2 1 10p 1.E-11 100p 1n 1.E-10 1.E-09 Normalized Capacitance; CL/GN (F) 10n 1.E-08 FIGURE 4-7: Recommended RISO Values for Capacitive Loads. After selecting RISO for your circuit, double check the resulting frequency response peaking and step response overshoot. Modify RISO’s value until the response is reasonable. Bench evaluation and simulations with the MCP661/2/3/5 SPICE macro model are helpful. Driving large capacitive loads can cause stability problems for voltage feedback op amps. As the load capacitance increases, the feedback loop’s phase margin decreases and the closed-loop bandwidth is reduced. This produces gain peaking in the frequency response, with overshoot and ringing in the step response. A unity gain buffer (G = +1) is the most sensitive to capacitive loads, though all gains show the same general behavior. © 2009 Microchip Technology Inc. DS22194A-page 23 MCP661/2/3/5 4.4.2 GAIN PEAKING Figure 4-8 shows an op amp circuit that represents non-inverting amplifiers (VM is a DC voltage and VP is the input) or inverting amplifiers (VP is a DC voltage and VM is the input). The capacitances CN and CG represent the total capacitance at the input pins; they include the op amp’s common mode input capacitance (CCM), board parasitic capacitance and any capacitor placed in parallel. Figure 2-37 and Figure 2-38 show the small signal and large signal step responses at G = -1 V/V. Since the noise gain is 2 V/V and CG ≈ 10 pF, the resistors were chosen to be RF = RG = 401Ω and RN = 200Ω. It is also possible to add a capacitor (CF) in parallel with RF to compensate for the de-stabilizing effect of CG. This makes it possible to use larger values of RF. The conditions for stability are summarized in Equation 4-6. EQUATION 4-6: RN VP Given: G N1 = 1 + R F ⁄ R G CN MCP66X G N2 = 1 + C G ⁄ C F VOUT VM RG FIGURE 4-8: Capacitance. CG fF = 1 ⁄ ( 2 π RF CF ) f Z = f F ( G N1 ⁄ G N2 ) We need: f F ≤ f GBWP ⁄ ( 2G N2 ) , G N1 < G N2 RF f F ≤ f GBWP ⁄ ( 4G N1 ) , G N1 > G N2 Amplifier with Parasitic CG acts in parallel with RG (except for a gain of +1 V/V), which causes an increase in gain at high frequencies. CG also reduces the phase margin of the feedback loop, which becomes less stable. This effect can be reduced by either reducing CG or RF. CN and RN form a low-pass filter that affects the signal at VP. This filter has a single real pole at 1/(2πRNCN). 1.E+05 100k Maximum Recommended R (Ω) F The largest value of RF that should be used depends on noise gain (see GN in Section 4.4.1 “Capacitive Loads”), CG and the open-loop gain’s phase shift. Figure 4-9 shows the maximum recommended RF for several CG values. Some applications may modify these values to reduce either output loading or gain peaking (step response overshoot). CG = 10 pF CG = 32 pF CG = 100 pF CG = 320 pF CG = 1 nF 10k 1.E+04 GN > +1 V/V 4.5 The MCP663 is a single amplifier with Chip Select (CS). When CS is pulled high, the supply current drops to 1 µA (typical) and flows through the CS pin to VSS. When this happens, the amplifier output is put into a high-impedance state. By pulling CS low, the amplifier is enabled. The CS pin has an internal 5 MΩ (typical) pulldown resistor connected to VSS, so it will go low if the CS pin is left floating. Figure 1-1, Figure 2-43 and Figure 2-44 show the output voltage and supply current response to a CS pulse. The MCP665 is a dual amplifier with two CS pins; CSA controls op amp A and CSB controls op amp B. These op amps are controlled independently, with an enabled quiescent current (IQ) of 6 mA/amplifier (typical) and a disabled IQ of 1 µA/amplifier (typical). The IQ seen at the supply pins is the sum of the two op amps’ IQ; the typical value for the MCP665’s IQ will be 2 µA, 6 mA or 12 mA when there are 0, 1 or 2 amplifiers enabled, respectively. 4.6 1k 1.E+03 100 1.E+02 1 FIGURE 4-9: vs. Gain. 10 Noise Gain; GN (V/V) 100 Maximum recommended RF Figure 2-35 and Figure 2-36 show the small signal and large signal step responses at G = +1 V/V. The unity gain buffer usually has RF = 0Ω and RG open. DS22194A-page 24 MCP663 and MCP665 Chip Select Power Supply With this family of operational amplifiers, the power supply pin (VDD for single supply) should have a local bypass capacitor (i.e., 0.01 µF to 0.1 µF) within 2 mm for good high frequency performance. Surface mount, multilayer ceramic capacitors, or their equivalent, should be used. These op amps require a bulk capacitor (i.e., 2.2 µF or larger) within 50 mm to provide large, slow currents. Tantalum capacitors, or their equivalent, may be a good choice. This bulk capacitor can be shared with other nearby analog parts as long as crosstalk through the supplies does not prove to be a problem. © 2009 Microchip Technology Inc. MCP661/2/3/5 4.7 High Speed PCB Layout These op amps are fast enough that a little extra care in the PCB (Printed Circuit Board) layout can make a significant difference in performance. Good PC board layout techniques will help you achieve the performance shown in the specifications and Typical Performance Curves; it will also help you minimize EMC (Electro-Magnetic Compatibility) issues. Use a solid ground plane. Connect the bypass local capacitor(s) to this plane with minimal length traces. This cuts down inductive and capacitive crosstalk. Separate digital from analog, low speed from high speed, and low power from high power. This will reduce interference. Keep sensitive traces short and straight. Separate them from interfering components and traces. This is especially important for high frequency (low rise time) signals. The output headroom limits would be VOL = -2.3V and VOH = +2.3V (see Figure 2-16), leaving some design room for the ±2V signal. The open-loop gain (AOL) typically does not decrease significantly with a 100Ω load (see Figure 2-11). The maximum power dissipated is about 48 mW (see Section 4.2.3 “Power Dissipation”), so the temperature rise (for the MCP661 in the SOIC-8 package) is under 8°C. 4.8.2 OPTICAL DETECTOR AMPLIFIER Figure 4-11 shows a transimpedance amplifier, using the MCP661 op amp, in a photo detector circuit. The photo detector is a capacitive current source. RF provides enough gain to produce 10 mV at VOUT. CF stabilizes the gain and limits the transimpedance bandwidth to about 1.1 MHz. RF’s parasitic capacitance (e.g., 0.2 pF for a 0805 SMD) acts in parallel with CF. CF 1.5 pF Sometimes, it helps to place guard traces next to victim traces. They should be on both sides of the victim trace, and as close as possible. Connect guard traces to ground plane at both ends, and in the middle for long traces. Use coax cables, or low inductance wiring, to route signal and power to and from the PCB. Mutual and self inductance of power wires is often a cause of crosstalk and unusual behavior. 4.8 4.8.1 Photo Detector ID 100 nA MCP66X VDD/2 50Ω LINE DRIVER Figure 4-10 shows the MCP661 driving a 50Ω line. The large output current (e.g., see Figure 2-18) makes it possible to drive a back-matched line (RM2, the 50Ω line and the 50Ω load at the far end) to more than ±2V (the load at the far end sees ±1V). It is worth mentioning that the 50Ω line and the 50Ω load at the far end together can be modeled as a simple 50Ω resistor to ground. RM1 49.9Ω -2.5V RG 301Ω FIGURE 4-10: FIGURE 4-11: Transimpedance Amplifier for an Optical Detector. 4.8.3 H-BRIDGE DRIVER Figure 4-12 shows the MCP662 dual op amp used as a H-bridge driver. The load could be a speaker or a DC motor. 50Ω Line RM2 49.9Ω 50Ω Line Driver. ½ MCP662 VIN RF VOT RF RL RGT 50Ω RGB RF 301Ω VDD/2 FIGURE 4-12: © 2009 Microchip Technology Inc. VOUT CD 30pF Typical Applications MCP66X +2.5V RF 100 kΩ RF VOB ½ MCP662 H-Bridge Driver. DS22194A-page 25 MCP661/2/3/5 This circuit automatically makes the noise gains (GN) equal, when the gains are set properly, so that the frequency responses match well (in magnitude and in phase). Equation 4-7 shows how to calculate RGT and RGB so that both op amps have the same DC gains; GDM needs to be selected first. EQUATION 4-7: V OT – V OB G DM ≡ -------------------------------- ≥ 1 V/V V IN – V DD ⁄ 2 RF R GT = -------------------------------( G DM ⁄ 2 ) – 1 RF R GB = -----------------G DM ⁄ 2 Equation 4-8 gives the resulting common mode and differential mode output voltages. EQUATION 4-8: V OT + V OB V DD -------------------------- = ---------2 2 V DD⎞ V OT – V OB = G DM ⎛⎝ V IN – ---------2 ⎠ DS22194A-page 26 © 2009 Microchip Technology Inc. MCP661/2/3/5 5.0 DESIGN AIDS Microchip provides the basic design aids needed for the MCP661/2/3/5 family of op amps. 5.1 SPICE Macro Model The latest SPICE macro model for the MCP661/2/3/5 op amps is available on the Microchip web site at www.microchip.com. This model is intended to be an initial design tool that works well in the op amp’s linear region of operation over the temperature range. See the model file for information on its capabilities. Bench testing is a very important part of any design and cannot be replaced with simulations. Also, simulation results using this macro model need to be validated by comparing them to the data sheet specifications and characteristic curves. 5.2 FilterLab® Software Microchip’s FilterLab® software is an innovative software tool that simplifies analog active filter (using op amps) design. Available at no cost from the Microchip web site at www.microchip.com/filterlab, the Filter-Lab design tool provides full schematic diagrams of the filter circuit with component values. It also outputs the filter circuit in SPICE format, which can be used with the macro model to simulate actual filter performance. 5.3 Mindi™ Circuit Designer & Simulator Microchip’s Mindi™ Circuit Designer & Simulator aids in the design of various circuits useful for active filter, amplifier and power management applications. It is a free online circuit designer & simulator available from the Microchip web site at www.microchip.com/mindi. This interactive circuit designer & simulator enables designers to quickly generate circuit diagrams, and simulate circuits. Circuits developed using the Mindi Circuit Designer & Simulator can be downloaded to a personal computer or workstation. 5.4 5.5 Analog Demonstration and Evaluation Boards Microchip offers a broad spectrum of Analog Demonstration and Evaluation Boards that are designed to help customers achieve faster time to market. For a complete listing of these boards and their corresponding user’s guides and technical information, visit the Microchip web site at www.microchip.com/analog tools. Some boards that are especially useful are: • • • • • • MCP6XXX Amplifier Evaluation Board 1 MCP6XXX Amplifier Evaluation Board 2 MCP6XXX Amplifier Evaluation Board 3 MCP6XXX Amplifier Evaluation Board 4 Active Filter Demo Board Kit 8-Pin SOIC/MSOP/TSSOP/DIP Evaluation Board, P/N SOIC8EV 5.6 Application Notes The following Microchip Application Notes are available on the Microchip web site at www.microchip. com/appnotes and are recommended as supplemental reference resources. • ADN003: “Select the Right Operational Amplifier for your Filtering Circuits”, DS21821 • AN722: “Operational Amplifier Topologies and DC Specifications”, DS00722 • AN723: “Operational Amplifier AC Specifications and Applications”, DS00723 • AN884: “Driving Capacitive Loads With Op Amps”, DS00884 • AN990: “Analog Sensor Conditioning Circuits – An Overview”, DS00990 • AN1228: “Op Amp Precision Design: Random Noise”, DS01228 Some of these application notes, and others, are listed in the design guide: • “Signal Chain Design Guide”, DS21825 Microchip Advanced Part Selector (MAPS) MAPS is a software tool that helps efficiently identify Microchip devices that fit a particular design requirement. Available at no cost from the Microchip website at www.microchip.com/maps, the MAPS is an overall selection tool for Microchip’s product portfolio that includes Analog, Memory, MCUs and DSCs. Using this tool, a customer can define a filter to sort features for a parametric search of devices and export side-by-side technical comparison reports. Helpful links are also provided for Data sheets, Purchase and Sampling of Microchip parts. © 2009 Microchip Technology Inc. DS22194A-page 27 MCP661/2/3/5 NOTES: DS22194A-page 28 © 2009 Microchip Technology Inc. MCP661/2/3/5 6.0 PACKAGING INFORMATION 6.1 Package Marking Information Example 8-Lead DFN (3×3) (MCP662) XXXX YYWW NNN Device MCP662 Note: Code DABQ Applies to 8-Lead 3x3 DFN 8-Lead SOIC (150 mil) (MCP661, MCP662, MCP663) XXXXXXXX XXXXYYWW NNN Example Device MCP665 Note: 10-Lead MSOP (MCP665) XXXXXX YWWNNN Legend: XX...X Y YY WW NNN e3 * Note: Example: MCP661E SN e3 0924 256 10-Lead DFN (3×3) (MCP665) XXXX YYWW NNN DABQ 0924 256 Code BAFD BAFD 0924 256 Applies to 10-Lead 3x3 DFN Example: 665EUN 924256 Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week ‘01’) Alphanumeric traceability code Pb-free JEDEC designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( e3 ) can be found on the outer packaging for this package. In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. © 2009 Microchip Technology Inc. DS22194A-page 29 MCP661/2/3/5 % 2% & %! % * %% 133)))& &3 " ) * ' !"#$ % * D e b N $ % % " % N L EXPOSED PAD E2 E K NOTE 1 1 2 D2 2 NOTE 1 1 BOTTOM VIEW TOP VIEW A NOTE 2 A3 A1 4% & 5&% 6!&( $ 55,, 6 6 67 8 9 % :./0 7 ; % 9 % "$$ . 0% %* + 7 5 % ,# , " "<"% ,2 +/0 = : 7 <"% , ,# = ( . + +. 5 + .. > = = " "5 % 0% %<"% 0% %5 % 0% % % ,# " " +/0 % ! " #$ %! & '(!%&! %( % ")%% % " * & & # "% ( % " + * ) ! % " & "% ,-. /01 / & % # % ! ))%!%% ,21 $ & '! ! )%!%% '$$& % ! ) 0 :/ DS22194A-page 30 © 2009 Microchip Technology Inc. MCP661/2/3/5 % 2% & %! % * %% 133)))& &3 © 2009 Microchip Technology Inc. " ) * ' !"#$ % * $ % % " % DS22194A-page 31 MCP661/2/3/5 % & ' (&))* 2% & %! % * %% 133)))& &3 " ) * ' !"#&'+,$ % * $ % % " % D e N E E1 NOTE 1 1 2 3 α h b h A2 A c φ L A1 L1 4% & 5&% 6!&( $ 55,, 6 6 8 /0 7 ; % * % "$$? 7 <"% " " * 67 9 % " " * β = = . = = = . , <"% 7 5 % . :/0 , +/0 /0 0 &$ @ % A . = . 2%5 % 5 = 2% % 5 2% I B = 9B 5 "* = . 5 "<"% ,2 ( + = . " $% D .B = .B " $% /%%& E .B = .B % ! " #$ %! & '(!%&! %( % ")%% % " ? $ %0 % % + & ","%!" &"$ %! "$ %! % # ".&& & "% ,-. /01 / & % # % ! ))%!%% ,21 $ & '! ! )%!%% '$$& % ! " ) 0 ./ DS22194A-page 32 © 2009 Microchip Technology Inc. MCP661/2/3/5 % & ' (&))* 2% & %! % * %% 133)))& &3 © 2009 Microchip Technology Inc. " ) * ' !"#&'+,$ % * $ % % " % DS22194A-page 33 MCP661/2/3/5 - % 2% & %! % * %% 133)))& &3 " ) * ' !"#$ % * D $ % % " % e b N N L K E E2 EXPOSED PAD NOTE 1 1 2 2 1 NOTE 1 D2 BOTTOM VIEW TOP VIEW A A1 A3 NOTE 2 4% & 5&% 6!&( $ 55,, 6 6 67 8 % ./0 7 ; % 9 % "$$ . 0% %* + 7 5 % ,# " "5 % ,2 +/0 +. 9 7 <"% , ,# , .9 . ( 9 . + 5 + . > = = " "<"% 0% %<"% 0% %5 % 0% % % ,# " " +/0 % ! " #$ %! & '(!%&! %( % ")%% % " * & & # "% ( % " + * ) ! % " & "% ,-. /01 / & % # % ! ))%!%% ,21 $ & '! ! )%!%% '$$& % ! ) 0 :+/ DS22194A-page 34 © 2009 Microchip Technology Inc. MCP661/2/3/5 - % 2% & %! % * %% 133)))& &3 © 2009 Microchip Technology Inc. " ) * ' !"#$ % * $ % % " % DS22194A-page 35 MCP661/2/3/5 - % )& ' ( .#&' $ 2% & %! % * %% 133)))& &3 " ) * ' % * $ % % " % D N E E1 NOTE 1 1 2 b e A A2 c φ L A1 L1 4% & 5&% 6!&( $ 55,, 6 6 ./0 7 ; % * % "$$ 7 <"% " " * 7 5 % 8 % " " * 67 = = . 9. . = . , <"% /0 , +/0 +/0 2%5 % 5 2% % 5 2% I B = 9B 5 9 = + "* : 9 .,2 5 "<"% ( . = ++ % ! " #$ %! & '(!%&! %( % ")%% % " & ","%!" &"$ %! "$ %! % # ".&& + & "% ,-. /01 / & % # % ! ))%!%% ,21 $ & '! ! )%!%% '$$& % ! " ) 0 / DS22194A-page 36 © 2009 Microchip Technology Inc. MCP661/2/3/5 APPENDIX A: REVISION HISTORY Revision A (July 2009) • Original Release of this Document. © 2009 Microchip Technology Inc. DS22194A-page 37 MCP661/2/3/5 NOTES: DS22194A-page 38 © 2009 Microchip Technology Inc. MCP661/2/3/5 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. -X /XX Device Temperature Range Package Device: MCP661 MCP661T MCP662 MCP662T MCP663 MCP663T MCP665 MCP665T Temperature Range: E Package: Single Op Amp Single Op Amp (Tape and Reel) (SOIC) Dual Op Amp Dual Op Amp (Tape and Reel) (DFN and SOIC) Single Op Amp with CS Single Op Amp with CS (Tape and Reel) (SOIC) Dual Op Amp with CS Dual Op Amp with CS (Tape and Reel) (DFN and MSOP) = -40°C to +125°C Examples: a) MCP661T-E/SN: Tape and Reel Extended temperature, 8LD SOIC package a) MCP662T-E/MF: Tape and Reel Extended temperature, 8LD DFN package MCP662T-E/SN: Tape and Reel Extended temperature, 8LD SOIC package b) a) MCP663T-E/SN: Tape and Reel Extended temperature, 8LD SOIC package a) MCP665T-E/MF: Tape and Reel Extended temperature, 10LD DFN package MCP665T-E/UN: Tape and Reel Extended temperature, 10LD MSOP package b) MF = Plastic Dual Flat, No Lead (3×3 DFN), 8-lead, 10-lead SN = Plastic Small Outline (3.90 mm), 8-lead UN = Plastic Micro Small Outline (MSOP), 10-lead © 2009 Microchip Technology Inc. DS22194A-page 39 MCP661/2/3/5 NOTES: DS22194A-page 40 © 2009 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, rfPIC and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MXDEV, MXLAB, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, ICEPIC, Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code Generation, PICC, PICC-18, PICkit, PICDEM, PICDEM.net, PICtail, PIC32 logo, REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 2009, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received ISO/TS-16949:2002 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. © 2009 Microchip Technology Inc. DS22194A-page 41 WORLDWIDE SALES AND SERVICE AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://support.microchip.com Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4080 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Kokomo Kokomo, IN Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8528-2100 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 Taiwan - Hsin Chu Tel: 886-3-6578-300 Fax: 886-3-6578-370 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 03/26/09 DS22194A-page 42 © 2009 Microchip Technology Inc.