CLC1007, CLC2007, CLC4007 Single, Dual, and Quad Low Cost, High Speed RRO Amplifiers FE ATU R E S ■■ 260MHz bandwidth ■■ Fully specified at +3V, +5V and ±5V supplies ■■ Output voltage range: ❏❏ 0.03V to 4.95V; V = +5; R = 2kΩ S L ■■ Input voltage range: ❏❏ -0.3V to +4.1V; V = +5 S ■■ 220V/μs slew rate ■■ 2.6mA supply current per amplifier ■■ ±100mA linear output current ■■ ±125mA short circuit current ■■ CLC2007 directly replaces LMH6643, AD8042, AD8052, and AD8092 ■■ CLC1007 directly replaces LMH6642, AD8041, AD8051, and AD8091 General Description The CLC1007 (single), CLC2007 (dual) and CLC4007(quad) are low cost, voltage feedback amplifiers. These amplifiers are designed to operate on +3V to +5V, or ±5V supplies. The input voltage range extends 300mV below the negative rail and 0.9V below the positive rail. The CLC1007, CLC2007, and CLC4007 offer superior dynamic performance with a 260MHz small signal bandwidth and 220V/μs slew rate. The combination of low power, high output current drive, and rail-torail performance make these amplifiers well suited for battery-powered communication/computing systems. The combination of low cost and high performance make the CLC1007, CLC2007, and CLC4007 suitable for high volume applications in both consumer and industrial applications such as wireless phones, scanners, color copiers, and video transmission. A P P LICATION S ■■ A/D driver ■■ Active filters ■■ CCD imaging systems ■■ CD/DVD ROM ■■ Coaxial cable drivers ■■ High capacitive load driver ■■ Portable/battery-powered applications ■■ Twisted pair driver ■■ Telecom and optical terminals ■■ Video driver Ordering Information - page 26 Output Voltage Swing vs Competition Large Signal Frequency Response 6 5 3 CLC2007 Output Amplitude (V) Normalized Gain (dB) 4 0 Vout = 2Vpp -3 Vout = 3Vpp Vout = 4Vpp -6 3 2 Competition 1 0 -1 -2 -3 -4 Vs = +/- 5V -9 0.1 RL = 50Ω VS = ±5V -5 1 10 100 -6 1000 -5 Frequency (MHz) © 2007-2014 Exar Corporation -4 -3 -2 -1 0 1 2 3 4 5 Input Amplitude (V) 1 / 27 exar.com/CLC1007 Rev 1D CLC1007, CLC2007, CLC4007 Absolute Maximum Ratings Operating Conditions Stresses beyond the limits listed below may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Supply Voltage Range..................................................2.7 to 12.6V Operating Temperature Range................................-40°C to 125°C Junction Temperature............................................................ 150°C Storage Temperature Range....................................-65°C to 150°C Lead Temperature (Soldering, 10s).......................................260°C VS.................................................................................. 0V to +14V VIN............................................................. -VS - 0.5V to +VS +0.5V Package Thermal Resistance θJA (TSOT23-5).................................................................215°C/W θJA (SOIC-8)......................................................................150°C/W θJA (MSOP-8)................................................................... 200°C/W θJA (SOIC-14)..................................................................... 90°C/W θJA (TSSOP-14).................................................................100°C/W Package thermal resistance (θJA), JEDEC standard, multi-layer test boards, still air. ESD Protection TSOT-5 (HBM)...........................................................................1kV SOIC-8 (HBM)...........................................................................1kV TSOT-5 (CDM)...........................................................................2kV SOIC-8 (CDM)...........................................................................2kV ESD Rating for HBM (Human Body Model) and CDM (Charged Device Model). © 2007-2014 Exar Corporation 2 / 27 exar.com/CLC1007 Rev 1D CLC1007, CLC2007, CLC4007 Electrical Characteristics at +3V TA = 25°C, VS = +3V, Rf = 1.5kΩ, RL = 2kΩ to VS/2; G = 2; unless otherwise noted. Symbol Parameter Conditions Min Typ Max Units Frequency Domain Response GBWP -3dB Gain Bandwidth Product G = +11, VOUT = 0.2Vpp 90 MHz UGBW Unity Gain Bandwidth VOUT = 0.2Vpp, RF = 0 245 MHz BWSS -3dB Bandwidth VOUT = 0.2Vpp 85 MHz f0.1dB 0.1dB Gain Flatness VOUT = 0.2Vpp, RL = 150Ω 16 MHz BWLS Large Signal Bandwidth VOUT = 2Vpp 55 MHz DC-coupled Output 0.03 % AC-coupled Output 0.04 % DC-coupled Output 0.03 ° AC-coupled Output 0.06 ° DG DP Differential Gain Differential Phase Time Domain tR, tF Rise and Fall Time VOUT = 0.2V step; (10% to 90%) 5 ns tS Settling Time to 0.1% VOUT = 1V step 25 ns OS Overshoot VOUT = 0.2V step 8 % SR Slew Rate G = -1, 2V step 175 V/μs Distortion/Noise Response THD Total Harmonic Distortion 1MHz, VOUT = 1Vpp 75 dBc en Input Voltage Noise >50kHz 16 nV/√Hz XTALK Crosstalk f = 5MHz 58 dB DC Performance VIO Input Offset Voltage dVIO Average Drift IB Input Bias Current dIB Average Drift IOS Input Offset Current PSRR Power Supply Rejection Ratio AOL Open Loop Gain IS Supply Current 0.5 mV 5 μV/°C 1.4 μA 2 nA/°C 0.05 μA DC 102 dB RL = 2kΩ 92 dB per channel 2.6 mA Input Characteristics CIN Input Capacitance CMIR Common Mode Input Range CMRR Common Mode Rejection Ratio 0.5 pF -0.3 to 2.1 V 100 dB RL = 150Ω 0.3 to 2.75 V RL = 2kΩ 0.02 to 2.96 V DC, VCM = 0 to 1.5V Output Characteristics VOUT Output Swing IOUT Output Current ISC Short Circuit Current VS Power Supply Operating Range VOUT = VS / 2 © 2007-2014 Exar Corporation 3 / 27 ±100 mA ±125 V 2.7 to 12.6 V exar.com/CLC1007 Rev 1D CLC1007, CLC2007, CLC4007 Electrical Characteristics at +5V TA = 25°C, VS = +5V, Rf = 1.5kΩ, RL = 2kΩ to VS/2; G = 2; unless otherwise noted. Symbol Parameter Conditions Min Typ Max Units Frequency Domain Response GBWP -3dB Gain Bandwidth Product G = +11, VOUT = 0.2Vpp 95 MHz UGBW Unity Gain Bandwidth VOUT = 0.2Vpp, RF = 0 250 MHz BWSS -3dB Bandwidth VOUT = 0.2Vpp 85 MHz f0.1dB 0.1dB Gain Flatness VOUT = 0.2Vpp, RL = 150Ω 35 MHz BWLS Large Signal Bandwidth VOUT = 2Vpp 65 MHz DC-coupled Output 0.03 % AC-coupled Output 0.04 % DC-coupled Output 0.03 ° AC-coupled Output 0.06 ° DG DP Differential Gain Differential Phase Time Domain tR, tF Rise and Fall Time VOUT = 0.2V step 5 ns tS Settling Time to 0.1% VOUT = 2V step 25 ns OS Overshoot VOUT = 0.2V step 5 % SR Slew Rate G = -1, 4V step 220 V/μs Distortion/Noise Response THD Total Harmonic Distortion 1MHz, VOUT = 2Vpp -75 dBc en Input Voltage Noise >50kHz 16 nV/√Hz XTALK Crosstalk f = 5MHz 58 dB DC Performance VIO Input Offset Voltage dVIO Average Drift -7 IB Input Bias Current dIB Average Drift IOS Input Offset Current PSRR Power Supply Rejection Ratio AOL Open Loop Gain IS Supply Current per channel 0.5 7 5 -2 1.4 2 2 -0.75 0.05 DC 80 102 RL = 2kΩ 80 92 2.6 mV μV/°C μA nA/°C 0.75 μA dB dB 4 mA Input Characteristics CIN Input Capacitance CMIR Common Mode Input Range CMRR Common Mode Rejection Ratio DC, VCM = 0 to 3.5V 0.5 pF -0.3 to 4.1 V 75 100 dB 0.35 0.1 to 4.9 Output Characteristics RL = 150Ω VOUT Output Swing RL = 2kΩ IOUT Output Current ISC Short Circuit Current VS Power Supply Operating Range VOUT = VS / 2 © 2007-2014 Exar Corporation 4 / 27 4.65 V 0.03 to 4.95 V ±100 mA ±125 V 2.7 to 12.6 V exar.com/CLC1007 Rev 1D CLC1007, CLC2007, CLC4007 Electrical Characteristics at ±5V TA = 25°C, VS = ±5V, Rf = 1.5kΩ, RL = 2kΩ to GND; G = 2; unless otherwise noted. Symbol Parameter Conditions Min Typ Max Units Frequency Domain Response GBWP -3dB Gain Bandwidth Product G = +11, VOUT = 0.2Vpp 90 MHz UGBW Unity Gain Bandwidth VOUT = 0.2Vpp, RF = 0 260 MHz BWSS -3dB Bandwidth VOUT = 0.2Vpp 85 MHz f0.1dB 0.1dB Gain Flatness VOUT = 0.2Vpp, RL = 150Ω 22 MHz BWLS Large Signal Bandwidth VOUT = 2Vpp 65 MHz DC-coupled Output 0.03 % AC-coupled Output 0.04 % DC-coupled Output 0.03 ° AC-coupled Output 0.06 ° DG DP Differential Gain Differential Phase Time Domain tR, tF Rise and Fall Time VOUT = 0.2V step 5 ns tS Settling Time to 0.1% VOUT = 2V step, RL = 100Ω 25 ns OS Overshoot VOUT = 0.2V step 5 % SR Slew Rate G = -1, 5V step 225 V/μs Distortion/Noise Response THD Total Harmonic Distortion 1MHz, VOUT = 2Vpp 76 dBc en Input Voltage Noise >50kHz 16 nV/√Hz XTALK Crosstalk f = 5MHz 58 dB DC Performance VIO Input Offset Voltage dVIO Average Drift IB Input Bias Current dIB Average Drift IOS Input Offset Current PSRR Power Supply Rejection Ratio AOL Open Loop Gain IS Supply Current 0.5 mV 5 μV/°C 1.3 μA 2 nA/°C 0.04 μA DC 102 dB RL = 2kΩ 92 dB per channel 2.6 mA Input Characteristics CIN Input Capacitance CMIR Common Mode Input Range CMRR Common Mode Rejection Ratio 0.5 pF -5.3 to 4.1 V 100 dB RL = 150Ω -4.8 to 4.8 V RL = 2kΩ -4.95 to 4.93 V DC, VCM = -5 to 3.5V Output Characteristics VOUT Output Swing IOUT Output Current ISC Short Circuit Current VS Power Supply Operating Range VOUT = VS / 2 © 2007-2014 Exar Corporation 5 / 27 ±100 mA ±125 V 2.7 to 12.6 V exar.com/CLC1007 Rev 1D CLC1007, CLC2007, CLC4007 CLC1007 Pin Configurations CLC1007 Pin Assignments TSOT-5 TSOT-5 OUT 1 -Vs 2 +IN 3 5 + +Vs 4 -IN SOIC-8 Pin Name Description 1 OUT Output 2 -VS Negative supply 3 +IN Positive input 4 -IN Negative input 5 +VS Positive supply SOIC-8 NC 1 -IN 2 +IN 3 -Vs Pin No. + 4 8 NC 7 +Vs 6 OUT 5 NC Pin No. Pin Name Description 1 NC No Connect 2 -IN Negative input 3 +IN Positive input 4 -VS Negative supply 5 NC No Connect 6 OUT Output 7 +VS Positive supply 8 NC No Connect CLC2007 Pin Configuration CLC2007 Pin Assignments SOIC-8 / MSOP-8 SOIC-8 / MSOP-8 OUT1 1 -IN1 2 +IN1 3 -Vs 4 + + Pin Name 1 OUT1 Description Output, channel 1 +Vs 2 -IN1 Negative input, channel 1 7 OUT2 3 +IN1 Positive input, channel 1 4 -IN2 -VS 6 5 +IN2 Positive input, channel 2 +IN2 6 -IN2 Negative input, channel 2 7 OUT2 8 +VS 8 - Pin No. 5 © 2007-2014 Exar Corporation 6 / 27 Negative supply Output, channel 2 Positive supply exar.com/CLC1007 Rev 1D CLC1007, CLC2007, CLC4007 CLC4007 Pin Configuration CLC4007 Pin Assignments SOIC-14 / TSSOP-14 SOIC-14 / TSSOP-14 OUT1 1 14 OUT4 -IN1 2 13 -IN4 +IN1 3 12 +IN4 +VS 4 11 -VS +IN2 5 10 +IN3 -IN2 6 9 -IN3 OUT2 7 8 OUT3 © 2007-2014 Exar Corporation Pin No. Pin Name Description 1 OUT1 2 -IN1 Negative input, channel 1 3 +IN1 Positive input, channel 1 4 +VS Positive supply 5 +IN2 Positive input, channel 2 6 -IN2 Negative input, channel 2 7 OUT2 Output, channel 2 8 OUT3 Output, channel 3 Output, channel 1 9 -IN3 Negative input, channel 3 10 +IN3 Positive input, channel 3 11 -VS 12 +IN4 Positive input, channel 4 13 -IN4 Negative input, channel 4 14 OUT4 7 / 27 Negative supply Output, channel 4 exar.com/CLC1007 Rev 1D CLC1007, CLC2007, CLC4007 Typical Performance Characteristics at +3V TA = 25°C, VS = +3V, RL = 2kΩ to VS/2, G = +2, RF = 1.5kΩ; unless otherwise noted. Non-Inverting Frequency Response Inverting Frequency Response 3 3 G = -1 Normalized Gain (dB) Normalized Gain (dB) G = +1, RF = 0Ω 0 G = +2 -3 G = +5 G = +10 -6 0 G = -2 -3 G = -5 G = -10 -6 Vs = +3V, VOUT = 0.2Vpp Vs = +3V, VOUT = 0.2Vpp -9 -9 0.1 1 10 100 1000 0.1 1 10 Frequency (MHz) 100 1000 Frequency (MHz) Frequency Response vs CL Frequency Response vs RL Vs = +3V, VOUT = 0.2Vpp CL = 47pF RS = 20Ω CL = 100pF RS = 18Ω 3 CL = 22pF No RS 0 Normalized Gain (dB) Normalized Gain (dB) 3 CL = 492pF RS = 7.5Ω -3 CL = 1000pF RS = 4.3Ω RL = 150Ω 0 RL = 500Ω -3 -6 -6 -9 -9 RL = 5KΩ RL = 1KΩ Vs = +3V, VOUT = 0.2Vpp 0.1 1 10 100 1000 0.1 1 10 Frequency (MHz) 100 1000 Frequency (MHz) Large Signal Frequency Response -3dB BW vs Output Voltage 120 3 110 RL = 2KΩ -3dB Bandwidth (MHz) Normalized Gain (dB) 100 0 Vout = 1Vpp -3 Vout = 2Vpp -6 90 80 RL = 150Ω 70 60 50 40 30 Vs = +3V -9 0.1 1 10 100 1000 0 Frequency (MHz) © 2007-2014 Exar Corporation Vs = +3V 20 0.5 1 1.5 2 Output Voltage (Vpp) 8 / 27 exar.com/CLC1007 Rev 1D CLC1007, CLC2007, CLC4007 Typical Performance Characteristics at +3V TA = 25°C, VS = +3V, RL = 2kΩ to VS/2, G = +2, RF = 1.5kΩ; unless otherwise noted. 2nd Harmonic Distortion vs RL over Frequency 55 -20 50 -30 45 -40 Distortion (dBc) Input Voltage Noise (nV/√Hz) Input Voltage Noise vs Frequency 40 35 30 Hd2_RL = 2KΩ -50 -60 Hd2_RL = 150Ω -70 25 -80 20 -90 15 -100 Vs = +3V_VOUT = 1Vpp 0.1 1 10 100 1000 0 5 10 Frequency (KHz) 15 20 Frequency (MHz) 3rd Harmonic Distortion vs RL over Frequency 2nd Harmonic Distortion vs VO over Frequency -20 -40 -30 -50 Hd3_RL = 150Ω -50 -60 Distortion (dBc) Distortion (dBc) -40 Hd3_RL = 2KΩ -70 -60 5MHz 2MHz -70 1MHz -80 -80 -90 -90 Vs = +3V_VOUT = 1Vpp Vs = +3V_RL = 150Ω -100 -100 0 5 10 15 20 0.5 1 Frequency (MHz) 1.5 2 Output Amplitude (Vpp) 3rd Harmonic Distortion vs VO over Frequency Non-Inverting Small Signal Pulse Response 1.7 -40 -50 -70 Voltage (V) Distortion (dBc) 1.6 5MHz -60 2MHz 1.5 -80 1.4 -90 1MHz Vs = +3V_RL = 150Ω Vs = +3V -100 1.3 0.5 1 1.5 0 2 Output Amplitude (Vpp) © 2007-2014 Exar Corporation 50 100 150 200 Time (ns) 9 / 27 exar.com/CLC1007 Rev 1D CLC1007, CLC2007, CLC4007 Typical Performance Characteristics at +3V TA = 25°C, VS = +3V, RL = 2kΩ to VS/2, G = +2, RF = 1.5kΩ; unless otherwise noted. Crosstalk vs Frequency (CLC2007) 3 -40 2.5 -50 2 -60 Crosstalk (dB) Voltage (V) Non-Inverting Large Signal Pulse Response 1.5 1 -70 -80 -90 0.5 Vs = +3V, RL = 150Ω, VOUT = 2Vpp Vs = +3V -100 0.01 0 0 50 100 150 200 Differential Gain & Phase_DC Coupled 0.1 1 10 Frequency (MHz) Time (ns) Differential Gain & Phase_AC Coupled © 2007-2014 Exar Corporation 10 / 27 exar.com/CLC1007 Rev 1D CLC1007, CLC2007, CLC4007 Typical Performance Characteristics at +5V TA = 25°C, VS = +5V, RL = 2kΩ to VS/2, G = +2, RF = 1.5kΩ; unless otherwise noted. Non-Inverting Frequency Response Inverting Frequency Response 3 3 G = -1 Normalized Gain (dB) Normalized Gain (dB) G = +1, RF = 0Ω 0 G = +2 -3 G = +5 G = +10 -6 0 G = -2 -3 G = -5 G = -10 -6 Vs = +5V, VOUT = 0.2Vpp Vs = +5V, VOUT = 0.2Vpp -9 -9 0.1 1 10 100 1000 0.1 1 10 Frequency (MHz) 100 1000 Frequency (MHz) Frequency Response vs CL Frequency Response vs RL Vs = +5V, VOUT = 0.2Vpp CL = 47pF RS = 20Ω CL = 100pF RS = 18Ω 3 CL = 22pF No RS 0 Normalized Gain (dB) Normalized Gain (dB) 3 CL = 492pF RS = 7.5Ω -3 CL = 1000pF RS = 4.3Ω RL = 150Ω 0 RL = 500Ω -3 -6 -6 -9 -9 RL = 5KΩ RL = 1KΩ Vs = +5V, VOUT = 0.2Vpp 0.1 1 10 100 1000 0.1 1 10 Frequency (MHz) 100 1000 Frequency (MHz) Large Signal Frequency Response -3dB BW vs Output Voltage 110 3 RL = 2KΩ 100 -3dB Bandwidth (MHz) Normalized Gain (dB) 90 0 Vout = 1Vpp -3 Vout = 2Vpp Vout = 3Vpp -6 80 RL = 150Ω 70 60 50 40 30 Vs = 5V Vs = +5V 20 -9 0.1 1 10 100 0 1000 © 2007-2014 Exar Corporation 0.5 1 1.5 2 2.5 3 Output Voltage (Vpp) Frequency (MHz) 11 / 27 exar.com/CLC1007 Rev 1D CLC1007, CLC2007, CLC4007 Typical Performance Characteristics at +5V TA = 25°C, VS = +5V, RL = 2kΩ to VS/2, G = +2, RF = 1.5kΩ; unless otherwise noted. 2nd Harmonic Distortion vs RL over Frequency 55 -20 50 -30 45 -40 Distortion (dBc) Input Voltage Noise (nV/√Hz) Input Voltage Noise vs Frequency 40 35 30 Hd2_RL = 2KΩ -50 -60 Hd2_RL = 150Ω -70 25 -80 20 -90 15 -100 Vs = +5V_VOUT = 2Vpp 0.1 1 10 100 1000 0 5 10 Frequency (KHz) 3rd Harmonic Distortion vs RL over Frequency 20 2nd Harmonic Distortion vs VO over Frequency -20 -40 -30 -50 -40 Hd3_RL = 150Ω Distortion (dBc) Distortion (dBc) 15 Frequency (MHz) -50 -60 -70 Hd3_RL = 2kΩ -60 2MHz 5MHz -70 -80 1MHz -80 -90 -90 Vs = +5V_V +/-5V_V ==2V2V OUT OUT pppp Vs = +5V_RL = 150Ω -100 -100 0 5 10 15 20 0.5 1 Frequency (MHz) 1.5 2 Output Amplitude (Vpp) 3rd Harmonic Distortion vs VO over Frequency Non-Inverting Small Signal Pulse Response 2.7 -40 -50 -70 Voltage (V) Distortion (dBc) 2.6 5MHz -60 2MHz 2.5 -80 2.4 -90 1MHz Vs = +5V_RL = 150Ω Vs = +5V 2.3 -100 0.5 1 1.5 0 2 © 2007-2014 Exar Corporation 50 100 150 200 Time (ns) Output Amplitude (Vpp) 12 / 27 exar.com/CLC1007 Rev 1D CLC1007, CLC2007, CLC4007 Typical Performance Characteristics at +5V TA = 25°C, VS = +5V, RL = 2kΩ to VS/2, G = +2, RF = 1.5kΩ; unless otherwise noted. Non-Inverting Large Signal Pulse Response Crosstalk vs Frequency (CLC2007) -40 5 -50 Crosstalk (dB) Voltage (V) 4 3 2 1 -60 -70 -80 -90 Vs = +5V, RL = 150Ω, VOUT = 2Vpp Vs = +5V -100 0.01 0 0 50 100 150 200 Differential Gain & Phase_DC Coupled 0.1 1 10 Frequency (MHz) Time (ns) Differential Gain & Phase_AC Coupled © 2007-2014 Exar Corporation 13 / 27 exar.com/CLC1007 Rev 1D CLC1007, CLC2007, CLC4007 Typical Performance Characteristics at ±5V TA = 25°C, VS = ±5V, RL = 2kΩ to GND, G = +2, RF = 1.5kΩ; unless otherwise noted. Non-Inverting Frequency Response Inverting Frequency Response 3 3 G = -1 Normalized Gain (dB) Normalized Gain (dB) G = +1, RF = 0Ω 0 G = +2 -3 G = +5 G = +10 0 G = -2 -3 G = -5 G = -10 -6 -6 Vs = +/- 5V, VOUT = 0.2Vpp Vs = +/- 5V, VOUT = 0.2Vpp -9 -9 0.1 1 10 100 0.1 1000 1 10 100 1000 Frequency (MHz) Frequency (MHz) Frequency Response vs CL Frequency Response vs RL Vs = +/- 5V, VOUT = 0.2Vpp CL = 47pF RS = 15Ω CL = 100pF RS = 15Ω 3 CL = 22pF No RS 0 Normalized Gain (dB) Normalized Gain (dB) 3 CL = 492pF RS = 6.5Ω -3 CL = 1000pF RS = 4.3Ω RL = 150Ω 0 RL = 500Ω -3 -6 -6 -9 -9 RL = 5KΩ RL = 1KΩ Vs = +/-5V, VOUT = 0.2Vpp 0.1 1 10 100 1000 0.1 1 10 Frequency (MHz) 100 1000 Frequency (MHz) Large Signal Frequency Response -3dB BW vs Output Voltage 110 3 100 RL = 2KΩ -3dB Bandwidth (MHz) Normalized Gain (dB) 90 0 Vout = 2Vpp -3 Vout = 3Vpp Vout = 4Vpp -6 80 RL = 150Ω 70 60 50 40 30 Vs = +/- 5V -9 Vs = +/-5V 20 0.1 1 10 100 1000 0 Frequency (MHz) © 2007-2014 Exar Corporation 0.5 1 1.5 2 2.5 3 3.5 4 Output Voltage (Vpp) 14 / 27 exar.com/CLC1007 Rev 1D CLC1007, CLC2007, CLC4007 Typical Performance Characteristics at ±5V TA = 25°C, VS = ±5V, RL = 2kΩ to GND, G = +2, RF = 1.5kΩ; unless otherwise noted. 2nd Harmonic Distortion vs RL over Frequency 55 -20 50 -30 45 -40 Distortion (dBc) Input Voltage Noise (nV/√Hz) Input Voltage Noise vs Frequency 40 35 30 Hd2_RL = 2KΩ -50 -60 Hd2_RL = 150Ω -70 25 -80 20 -90 15 -100 Vs = +/-5V_VOUT = 2Vpp 0.1 1 10 100 1000 0 5 10 Frequency (KHz) 3rd Harmonic Distortion vs RL over Frequency 20 2nd Harmonic Distortion vs VO over Frequency -20 -40 -30 -50 -40 Hd3_RL = 150Ω Distortion (dBc) Distortion (dBc) 15 Frequency (MHz) -50 -60 -70 Hd3_RL = 2kΩ -60 5MHz 2MHz -70 -80 -80 1MHz -90 -90 Vs = +/-5V_VOUT = 2Vpp Vs = +/-5V_RL = 150Ω -100 -100 0 5 10 15 20 0.5 1 Frequency (MHz) 1.5 2 Output Amplitude (Vpp) 3rd Harmonic Distortion vs VO over Frequency Non-Inverting Small Signal Pulse Response -40 0.25 0.2 0.15 0.1 -60 5MHz -70 Voltage (V) Distortion (dBc) -50 2MHz -80 0.05 0 -0.05 -0.1 -0.15 -90 1MHz -0.2 Vs = +/-5V_RL = 150Ω -100 Vs = +/-5V -0.25 0.5 1 1.5 2 0 Output Amplitude (Vpp) © 2007-2014 Exar Corporation 50 100 150 200 Time (ns) 15 / 27 exar.com/CLC1007 Rev 1D CLC1007, CLC2007, CLC4007 Typical Performance Characteristics at ±5V TA = 25°C, VS = ±5V, RL = 2kΩ to GND, G = +2, RF = 1.5kΩ; unless otherwise noted. Crosstalk vs Frequency (CLC2007) 3 -40 2 -50 1 -60 Crosstalk (dB) Voltage (V) Non-Inverting Large Signal Pulse Response 0 -1 -70 -80 -90 -2 Vs = +/- 5V, RL = 150Ω, VOUT = 2Vpp Vs = +/-5V -100 0.01 -3 0 50 100 150 200 Differential Gain & Phase_DC Coupled 0.1 1 10 Frequency (MHz) Time (ns) Differential Gain & Phase_AC Coupled © 2007-2014 Exar Corporation 16 / 27 exar.com/CLC1007 Rev 1D CLC1007, CLC2007, CLC4007 Application Information +Vs General Description The CLC1007, CLC2007, and CLC4007 are single supply, general purpose, voltage-feedback amplifiers fabricated on a complementary bipolar process using a patent pending topography. They feature a rail-to-rail output stage and is unity gain stable. Both gain bandwidth and slew rate are insensitive to temperature. Input 0.1μF + Output RL 0.1μF The common mode input range extends to 300mV below ground and to 0.9V below Vs. Exceeding these values will not cause phase reversal. However, if the input voltage exceeds the rails by more than 0.5V, the input ESD devices will begin to conduct. The output will stay at the rail during this overdrive condition. 6.8μF G=1 -Vs Figure 3: Unity Gain Circuit +Vs The design is short circuit protected and offers “soft” saturation protection that improves recovery time. 6.8μF + Figures 1, 2, and 3 illustrate typical circuit configurations for non-inverting, inverting, and unity gain topologies for dual supply applications. They show the recommended bypass capacitor values and overall closed loop gain equations. Figure 4 shows the typical non-inverting gain circuit for single supply applications. +Vs 6.8μF In 0.1μF + Out - Rf Rg 6.8μF Figure 4: Single Supply Non-Inverting Gain Circuit Input 0.1μF + Output RL 0.1μF Rg 6.8μF -Vs Rf G = 1 + (Rf/Rg) Figure 1: Typical Non-Inverting Gain Circuit +Vs Overdrive Recovery For an amplifier, an overdrive condition occurs when the output and/or input ranges are exceeded. The recovery time varies based on whether the input or output is overdriven and by how much the ranges are exceeded. The CLC1007, CLC2007, and CLC4007 will typically recover in less than 20ns from an overdrive condition. Figure 5 shows the CLC2007 in an overdriven condition. 6 6.8μF OUTPUT 4 Input Rg 0.1μF + 2 Voltage (V) R1 Output RL 0.1μF 0 INPUT -2 Rf -4 6.8μF -Vs Vs = +/-5V_RL=2K_AV=+5 G = - (Rf/Rg) -6 0 For optimum input offset voltage set R1 = Rf || Rg 200 300 400 500 600 700 800 900 1,000 Time (ns) Figure 2: Typical Inverting Gain Circuit © 2007-2014 Exar Corporation 100 Figure 5: Overdrive Recovery 17 / 27 exar.com/CLC1007 Rev 1D CLC1007, CLC2007, CLC4007 Power Dissipation Power dissipation should not be a factor when operating under the stated 2kΩ load condition. However, applications with low impedance, DC coupled loads should be analyzed to ensure that maximum allowed junction temperature is not exceeded. Guidelines listed below can be used to verify that the particular application will not cause the device to operate beyond it’s intended operating range. Assuming the load is referenced in the middle of the power rails or Vsupply/2. The CLC1007 is short circuit protected. However, this may not guarantee that the maximum junction temperature (+150°C) is not exceeded under all conditions. Figure 6 shows the maximum safe power dissipation in the package vs. the ambient temperature for the packages available. 2.5 Maximum Power Dissipation (W) Maximum power levels are set by the absolute maximum junction rating of 170°C. To calculate the junction temperature, the package thermal resistance value ThetaJA (θJA) is used along with the total die power dissipation. TJunction = TAmbient + (θJA × PD) Where TAmbient is the temperature of the working environment. In order to determine PD, the power dissipated in the load needs to be subtracted from the total power delivered by the supplies. TSSOP-14 2 SOIC-14 1.5 SOIC-8 1 0.5 TSOT-5 MSOP-8 0 -40 -20 0 20 40 60 80 100 120 Ambient Temperature (°C) PD = Psupply - Pload Figure 6. Maximum Power Derating Supply power is calculated by the standard power equation. Psupply = Vsupply × IRMSsupply Vsupply = VS+ - VSPower delivered to a purely resistive load is: Pload = ((Vload)RMS2)/Rloadeff The effective load resistor (Rloadeff) will need to include the effect of the feedback network. For instance, Driving Capacitive Loads Increased phase delay at the output due to capacitive loading can cause ringing, peaking in the frequency response, and possible unstable behavior. Use a series resistance, RS, between the amplifier and the load to help improve stability and settling performance. Refer to Figure 7. Rloadeff in Figure 3 would be calculated as: Input + RL || (Rf + Rg) - These measurements are basic and are relatively easy to perform with standard lab equipment. For design purposes however, prior knowledge of actual signal levels and load impedance is needed to determine the dissipated power. Here, PD can be found from PD = PQuiescent + PDynamic - Pload Quiescent power can be derived from the specified IS values along with known supply voltage, Vsupply. Load power can be calculated as above with the desired signal amplitudes using: Rf Output CL RL Rg Figure 7. Addition of RS for Driving Capacitive Loads Table 1 provides the recommended RS for various capacitive loads. The recommended RS values result in approximately <1dB peaking in the frequency response. CL (pF) (Vload)RMS = Vpeak / √2 ( Iload)RMS = ( Vload)RMS / Rloadeff The dynamic power is focused primarily within the output stage driving the load. This value can be calculated as: PDynamic = (VS+ - Vload)RMS × ( Iload)RMS © 2007-2014 Exar Corporation Rs RS (Ω) -3dB BW (MHz) 22pF 0 118 47pF 15 112 100pF 15 91 492pF 6.5 59 Table 1: Recommended RS vs. CL 18 / 27 exar.com/CLC1007 Rev 1D CLC1007, CLC2007, CLC4007 For a given load capacitance, adjust RS to optimize the tradeoff between settling time and bandwidth. In general, reducing RS will increase bandwidth at the expense of additional overshoot and ringing. Layout Considerations General layout and supply bypassing play major roles in high frequency performance. Exar has evaluation boards to use as a guide for high frequency layout and as an aid in device testing and characterization. Follow the steps below as a basis for high frequency layout: ■■ Include 6.8µF and 0.1µF ceramic capacitors for power supply decoupling ■■ Place the 6.8µF capacitor within 0.75 inches of the power pin ■■ Place the 0.1µF capacitor within 0.1 inches of the power pin ■■ ■■ Remove the ground plane under and around the part, especially near the input and output pins to reduce parasitic capacitance Minimize all trace lengths to reduce series inductances Refer to the evaluation board layouts below for more information. Figure 8. CEB002 & CEB003 Schematic Evaluation Board Information The following evaluation boards are available to aid in the testing and layout of these devices: Evaluation Board # Products CEB002 CLC1007 in TSOT CEB003 CLC1007 in SOIC CEB006 CLC2007 in SOIC CEB010 CLC2007 in MSOP CEB018 CLC4007 in SOIC CEB019 CLC4007 in TSSOP Evaluation Board Schematics Figure 9. CEB002 Top View Evaluation board schematics and layouts are shown in Figures 8-20. These evaluation boards are built for dualsupply operation. Follow these steps to use the board in a single-supply application: 1. Short -VS to ground. 2. Use C3 and C4, if the -VS pin of the amplifier is not directly connected to the ground plane. © 2007-2014 Exar Corporation 19 / 27 exar.com/CLC1007 Rev 1D CLC1007, CLC2007, CLC4007 Figure 10. CEB002 Bottom View Figure 13. CEB006 & CEB010 Schematic Figure 11. CEB003 Top View Figure 14. CEB006 Top View Figure 12. CEB003 Bottom View © 2007-2014 Exar Corporation 20 / 27 exar.com/CLC1007 Rev 1D CLC1007, CLC2007, CLC4007 Figure 15. CEB006 Bottom View Figure 18. CEB018 Schematic Figure 16. CEB010 Top View Figure 19. CEB018 Top View Figure 17. CEB010 Bottom View © 2007-2014 Exar Corporation 21 / 27 exar.com/CLC1007 Rev 1D CLC1007, CLC2007, CLC4007 Figure 20. CEB018 Bottom View © 2007-2014 Exar Corporation 22 / 27 exar.com/CLC1007 Rev 1D CLC1007, CLC2007, CLC4007 Mechanical Dimensions TSOT-5 Package MSOP-8 Package © 2007-2014 Exar Corporation 23 / 27 exar.com/CLC1007 Rev 1D CLC1007, CLC2007, CLC4007 SOIC-8 Package SOIC-14 Package © 2007-2014 Exar Corporation 24 / 27 exar.com/CLC1007 Rev 1D ECN 1344-13 11/01/2013 CLC1007, CLC2007, CLC4007 TSSOP-14 Package ECN 1347-07 11/19/2013 © 2007-2014 Exar Corporation 25 / 27 exar.com/CLC1007 Rev 1D CLC1007, CLC2007, CLC4007 Ordering Information Part Number Package Green Operating Temperature Range Packaging CLC1007IST5X TSOT-5 Yes -40°C to +125°C Tape & Reel CLC1007IST5MTR TSOT-5 Yes -40°C to +125°C Mini Tape & Reel CLC1007IST5EVB Evaluation Board N/A N/A N/A CLC1007ISO8X SOIC-8 Yes -40°C to +125°C Tape & Reel CLC1007ISO8MTR SOIC-8 Yes -40°C to +125°C Mini Tape & Reel CLC1007ISO8EVB Evaluation Board N/A N/A N/A CLC2007ISO8X SOIC-8 Yes -40°C to +125°C Tape & Reel CLC2007ISO8MTR SOIC-8 Yes -40°C to +125°C Mini Tape & Reel CLC2007ISO8EVB Evaluation Board N/A N/A N/A CLC2007IMP8X MSOP-8 Yes -40°C to +125°C Tape & Reel CLC2007IMP8MTR MSOP-8 Yes -40°C to +125°C Mini Tape & Reel CLC2007IMP8EVB Evaluation Board N/A N/A N/A CLC4007ITP14X TSSOP-14 Yes -40°C to +125°C Tape & Reel CLC4007ITP14MTR TSSOP-14 Yes -40°C to +125°C Mini Tape & Reel CLC4007ITP14EVB Evaluation Board N/A N/A N/A CLC4007ISO14X SOIC-14 Yes -40°C to +125°C Tape & Reel CLC4007ISO14MTR SOIC-14 Yes -40°C to +125°C Mini Tape & Reel CLC4007ISO14EVB Evaluation Board N/A N/A N/A CLC1007 Ordering Information CLC2007 Ordering Information CLC4007 Ordering Information Moisture sensitivity level for all parts is MSL-1. © 2007-2014 Exar Corporation 26 / 27 exar.com/CLC1007 Rev 1D CLC1007, CLC2007, CLC4007 Revision History Revision 1D (ECN 1451-07) Date December 2014 Description Reformat into Exar data sheet template. Updated ordering information table to include MTR and EVB part numbers. Increased “I” temperature range from +85 to +125°C. Removed “A” temp grade parts, since “I” is now equivalent. Updated thermal resistance numbers and package outline drawings. For Further Assistance: Email: [email protected] or [email protected] Exar Technical Documentation: http://www.exar.com/techdoc/ Exar Corporation Headquarters and Sales Offices 48760 Kato Road Tel.: +1 (510) 668-7000 Fremont, CA 94538 - USA Fax: +1 (510) 668-7001 NOTICE EXAR Corporation reserves the right to make changes to the products contained in this publication in order to improve design, performance or reliability. EXAR Corporation assumes no responsibility for the use of any circuits described herein, conveys no license under any patent or other right, and makes no representation that the circuits are free of patent infringement. Charts and schedules contained here in are only for illustration purposes and may vary depending upon a user’s specific application. While the information in this publication has been carefully checked; no responsibility, however, is assumed for inaccuracies. EXAR Corporation does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless EXAR Corporation receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has been minimized; (b) the user assumes all such risks; (c) potential liability of EXAR Corporation is adequately protected under the circumstances. Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited. © 2007-2014 Exar Corporation 27 / 27 exar.com/CLC1007 Rev 1D