MD200xEI Series Low Cost, 2W High Isolation SIP DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: • 2W Output Power • Miniature SIP Case • Short Circuit Protected • 3,000 VDC Isolation Input Parameter Conditions Min. 5 VDC Input 4.50 12 VDC Input 10.80 15 VDC Input 13.50 24 VDC Input 21.60 Internal Capacitor Input Voltage Range Input Filter • Single and Dual Outputs Output • >3.5 MHour MTBF Parameter Output Voltage Accuracy Line Regulation Load Regulation, See Note 1 • -40°C to +105°C Operation • LOW COST Ripple & Noise (20 MHz), See Note 2 1.5 kV Isolation Models Available Conditions Min. Typ. 5.0 12.0 15.0 24.0 Max. 5.50 13.20 16.50 26.40 Units Typ. ±2.5 Max. Units % % For VIN Change of 1% See Model Selection Guide Output Voltage <12 VDC 60 15 VDC, 24 VDC Output 75 Temperature Coefficient Output Short Circuit ±1.2 VDC mV P - P ±0.03 %/°C Typ. Max. 20 100 300 Units VDC M pF kHz Continuous (Autorecovery) General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance, See Note 3 Switching Frequency EMI Characteristics Parameter Conditions 60 Seconds 500 VDC 100 kHz, 1V Conditions EMC Compliance, Single Output EMC Compliance, Dual Output Min. Conducted Radiated EMI Compliance, See Note 5 Min. 3,000 1,000 Electrostatic Discharge (ESD) Typ. Max. Units CISPR22/EN 55022 Level B CISPR22/EN 55022 Level B EN 61000-4-2 Level B Contact ±8 kV EN 61000-4-2 Level B Contact ±6 kV Environmental MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Physical Case Size Case Material Weight Conditions Min. Typ. -40 +25 -55 Free Air Convection RH, Non-condensing Ambient Max. +105 +125 Units °C °C 95 % 0.772 x 0.276 x 0.394 Inches (19.6 x 7.0 x 10.0 mm) Non-Conductive Black Plastic (UL-94V0) 0.08 Oz (2.4g) Reliability Specifications Parameter MTBF Conditions MIL HDBK 217F, 25°C, Gnd Benign Min. 3.5 Typ. Max. Units MHours Min. -0.7 -0.7 -0.7 -0.7 Typ. Max. 9.0 18.0 21.0 30.0 300 Units Absolute Maximum Ratings Parameter Conditions Input Voltage Surge (1 Sec) Lead Temperature 5 VDC Input 12 VDC Input 15 VDC Input 24 VDC Input 1.5 mm From Case For 10 Sec Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. www.micropowerdirect.com VDC °C www.micropowerdirect.com Model Selection Guide Input Model Number MD205S-05EI MD205S-12EI MD205S-15EI MD205S-24EI MD205D-05EI MD205D-12EI MD205D-15EI MD205D-24EI MD212S-05EI MD212S-12EI MD212S-15EI MD212D-05EI MD212D-12EI MD212D-15EI MD215D-12EI MD224S-05EI MD224S-12EI MD224S-15EI MD224S-24EI MD224D-05EI MD224D-12EI MD224D-15EI Output Voltage (VDC) Current (mA) Nominal Range Full-Load No-Load 5 4.5 - 5.5 450 25 5 4.5 - 5.5 476 25 5 4.5 - 5.5 476 25 5 4.5 - 5.5 476 25 5 4.5 - 5.5 476 25 5 4.5 - 5.5 476 25 5 4.5 - 5.5 476 25 5 4.5 - 5.5 476 25 12 10.8 - 13.2 198 15 12 10.8 - 13.2 198 15 12 10.8 - 13.2 198 15 12 10.8 - 13.2 198 15 12 10.8 - 13.2 196 15 12 10.8 - 13.2 198 15 15 13.5 - 16.5 157 10 24 21.6 - 26.4 99 8 24 21.6 - 26.4 99 8 24 21.6 - 26.4 99 8 24 21.6 - 26.4 98 8 24 21.6 - 26.4 99 8 24 21.6 - 26.4 99 8 24 21.6 - 26.4 99 8 Voltage Current Current (VDC) (mA, Max) (mA, Min) 5.0 12.0 15.0 24.0 ±5.0 ±12.0 ±15.0 ±24.0 5.0 12.0 15.0 ±5.0 ±12.0 ±15.0 ±12.0 5.0 12.0 15.0 24.0 ±5.0 ±12.0 ±15.0 400.0 166.6 133.3 83.3 ±200.0 ±83.3 ±66.6 ±41.6 400.0 166.6 133.3 ±200.0 ±83.3 ±66.6 ±83.3 400.0 166.6 133.3 83.3 ±200.0 ±83.3 ±66.6 40.0 16.6 13.3 8.3 ±20.0 ±8.3 ±6.7 ±4.2 40.0 16.6 13.3 ±20.0 ±8.3 ±6.7 ±8.3 40.0 16.6 13.3 8.3 ±20.0 ±8.3 ±6.7 Notes: 1. Output load regulation is specified for a load change of 10% to 100%. 2. When measuring output ripple, it is recommended that an external 1 µF ceramic capacitor & 10 µF electrolytic capacitor be placed in parallel from the +Vout pin to the -Vout pin for single output models, or from each output to common for dual output models. 3. The isolation capacitance of model MD224S-15EI and MD224D-24EI is 30 pF. 4. Operation at no load will not damage these units, however, they may not meet all specifications. 5. These converters are specified for operation without external components. However, in some applications the addition of input/output capacitors will enhance stability and reduce output ripple. The simple connection shown below will typically meet EN 55022 Class B. For dual output units, a capacitor should be connected from each output to common (C2 is connected to pin 5 on dual output models). Output Load Fuse Rating Regulation Capacitive Efficiency Slow-Blow Load (%, Typ) (mA) % Typ. (µF Max) 10.0 8.0 7.0 6.0 10.0 8.0 7.0 6.0 10.0 8.0 7.0 10.0 8.0 7.0 8.0 10.0 8.0 7.0 6.0 10.0 8.0 7.0 220 220 220 220 100 100 100 100 220 220 220 100 100 100 100 220 220 220 220 100 100 100 89 84 84 84 80 84 84 84 84 84 84 84 85 84 85 84 84 84 85 84 84 84 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 500 500 500 500 500 500 500 250 250 250 250 250 250 250 Derating Curve Mechanical Dimensions Me VIN C1 L1 C2 VOUT C3 5 VDC 12 VDC 15 VDC 24 VDC 4.7 µF/50V 4.7 µF/50V 4.7 µF/50V 4.7 µF/50V 6.8 µH 6.8 µH 6.8 µH 6.8 µH --470 pF/3kV 470 pF/3kV 470 pF/3kV 5 VDC 12 VDC 15 VDC 24 VDC ±5 VDC ±12 VDC ±15 VDC ±24 VDC 10 µF 2.2 µF 1.0 µF 1.0 µF 4.7 µF 1.0 µF 0.47 µF 0.47 µF 6. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Pin Connections Pin Single Dual Pin Single Dual 1 +VIN +VIN 6 No Pin Common 2 -VIN -VIN 7 +VOUT +VOUT 5 -VOUT -VOUT MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.02 (±0.50) • Pin 1 is marked by a “dot” or indentation on the unit FAX: (781) 344-8481 • E-Mail: [email protected]