SAW BANDPASS FILTER PART NO.: ACTF9376/2345MHz/DCC6C_v1.0 Product Type: Customer: SAW Filter Part NO.: Customer Part NO.: ACTF9376/2345MHz/DCC6C_v1.0 PREPARED BY Issued Date: CHECKED BY APPROVED BY Features Low-loss RF filter High Rejection Single Ended Operation at 50Ω without matching Ceramic Package for Surface Mounted Technology (SMT) Lead-free Production and RoHS Compliance Package Dimensions Ceramic Package: DCC6C Pin Configuration 2 Input 5 Output 1, 3, 4, 6 Case Ground 1, 3, 4, 6 To Be Grounded Marking Top View, Laser Marking "ND”: “9376”: “＊”: Code 1 2 Manufacturer’s mark “F”: SAW filter Part number ” · ”: Terminal 1 Lot number (The code shown below varies in a 4-year cycle) 3 4 5 6 7 8 9 10 11 12 2013 A B C D E F G H J K L M 2014 N P Q R S T U V W X Y Z 2015 a b c d e f g h i j k m 2016 n p q r s t u v w x y z Maximum Ratings Rating Value Unit Operating Temperature Range TA -40 ~ +85 °C Storage Temperature Range Tstg -40 ~ +85 °C DC Voltage (between any Terminals) VDC 12 V P 10max. dBm RF Power (in BW) -2- Electrical Characteristics Minimum Typical Maximum Unit Center Frequency Item fC - 2345 - MHz Maximum Insertion Loss in 2320 MHz–2370MHz IL - 2.6 3.2 dB 0.7 1.2 dB 33 - dB - dB Amplitude Variation in 2320 MHz–2370MHz α Absolute Attenuation 0.30 … 2170.0MHz 30 2170.0 … 2190.0 MHz 30 34 2190.0 … 2300.0 MHz 4 8.5 2400.0 … 2460.0 MHz 12 15 - dB 2460.0 … 2585.0 MHz 30 40 - dB 2585.0 … 3000.0 MHz dB 25 35 -- Input VSWR in 2320 MHz–2370MHz - 1.8:1 2.0:1 Output VSWR in 2320 MHz–2370MHz - 1.8:1 2.0:1 15 30 Group delay ripple 2320 MHz–2370MHz Source / Load Impedance (single ended) 50 RoHS Compliant Electrostatic Sensitive Device Typical Frequency Response -3- ns Ω -4- Stability Characteristics Test item Condition of test 1 Mechanical shock (a) Drops: 3 times on concrete floor (b) Height: 1.0 m 2 Vibration resistance (a) Frequency of vibration: 10~55Hz (c) Directions: X,Y and Z (b) Amplitude: 1.5 mm (d) Duration: 2 hours 3 Moisture resistance (a) Condition: 40°C, 90~95% R.H. (c) Wait 4 hours before measurement (b) Duration: 96 hours 4 Climatic sequence (a) +70°C for 16 hours (b) +55°C for 24 hours, 90~95% R.H. (c) -25°C for 2 hours (d) +40°C for 24 hours, 90~95% R.H. (e) Wait 4 hours before measurement 5 High temperature exposure (a) Temperature: 70°C (c) Wait 4 hours before measurement 6 Thermal impact (a) +70°C for 30 minutes ⇒ -25°C for 30 minutes repeated 3 times (b) Wait 4 hours before measurement (b) Duration: 250 hours Requirements: The SAW filer shall remain within the electrical specifications after tests. Remarks SAW devices should not be used in any type of fluid such as water, oil, organic solvent, etc. Be certain not to apply voltage exceeding the rated voltage of components. Do not operate outside the recommended operating temperature range of components. Sudden change of temperature shall be avoided, deterioration of the characteristics can occur. Be careful of soldering temperature and duration of components when soldering. Do not place soldering iron on the body of components. Be careful not to subject the terminals or leads of components to excessive force. SAW devices are electrostatic sensitive. Please avoid static voltage during operation and storage. Ultrasonic cleaning shall be avoided. Ultrasonic vibration may cause destruction of components. Test Circuit Recommended Land Pattern 50Ω / 50Ω Configuration -5- Packing Information Carrier Tape Reel Dimensions Outer Packing Type Carton Box Ⅰ Carton Box Ⅱ Quantity Dimension Description Weight 10000 190×190×95 0.85 20000 190×190×190 anti-static plastic bag & carton box 1 reel / bag 5 bags / box (10000 pcs) 10 bags / box (20000 pcs) Unit: mm 1.70 Unit: kg -6- Recommended Soldering Profile C ACT2013. All Rights Reserved. ○ A E 1. 2. 3. A The specifications of this device are subject to change or obsolescence without notice. Typically, equipment utilizing this device requires emissions testing and government approval, which is the responsibility of the equipment manufacturer. Our liability is only assumed for the Surface Acoustic Wave (SAW) component(s) per se, not for applications, processes and circuits implemented within components or assemblies. -7-