POWER DS500SPE 500 Watts Distributed Power System Data Sheet Front-end Bulk Power Total Output Power: 500 W continuous Wide Input Voltage: 90 to 264 Vac SPECIAL FEATURES 500 W output power High-power and short form factor 1U power supply Active Power Factor Correction EN61000-3-2 Harmonic compliance Inrush current control 80plus Platinum efficiency N+1 or N+N redundant Hot-pluggable Active current sharing Full digital control PMBus compliant Compatible with Artesyn’s Universal PMBus GUI Reverse airflow option Two-year warranty Electrical Specifications Input COMPLIANCE Input range 90 - 264 Vac Frequency 47 Hz to 63 Hz Efficiency 94.0% peak Max Input current 6.6 Arms @ 90 Vac Inrush current 38 Apk Conducted EMI Class A with 6 dB margin Radiated EMI Class A with 6 dB margin Power factor >0.9 beginning at 20% load ITHD 10% Leakage current 1.75 mA Hold-up time 10 ms at full load Output Conducted/Radiated EMI Class A Limits + 6 dB margin EN61000-4-11 Main DC Output SAFETY UL/cUL Demko +CB Report CE Mark CCC BSMI NOM MAX MIN NOM MAX Nominal setting -0.20% 12 0.20% -1% 12 1% Total output regulation range 11.4 V 12.6 V 11.4 V 12.6 V Dynamic load regulation range 11.4 V 12.6 V 11.4 V 12.6 V Output ripple 150 mVp-p Output current 0.5 A Current sharing Within ±5% of full load rating Capacitive loading 700 uF 1 Start-up from AC to output Output rise time 1 Standby DC Output MIN 41.6 A 5,000 uF 150 mVp-p 0.1 A 47 uF 2200 ms 5 ms 50 ms 3.0 A N/A 680 uF 1700 ms 2 ms 60 ms Minimum current for transient load response testing only. Unit is designed to operate and be within output regulation range at zero load. DS500SPE Data Sheet Electrical Specifications Protections Main Output MIN NOM MAX Overcurrent protection2 120% 150% Overvoltage protection1 13.5 V 15.0 V Undervoltage protection 10.5 V 11.0 V Overtemperature protection Yes Fan fault protection Yes Standby Output Overcurrent protection3 120% 150% Overvoltage protection 13.5 V 15.0 V Undervoltage protection 10.0 V 11.0 V 3 1 2 3 Latch mode Autorecovery if the overcurrent is less than 120% and last only for <500 ms Standby protection is auto-recovery Ordering Information Model Number Nominal Main Output Standby Output Airflow Direction DS500SPE-3 12 V @ 41.6 A 12 V @ 3 A Standard (forward) DS500SPE-3-001 12 V @ 41.6 A 12 V @ 3 A Reverse Control and Status Signals Input Signals PSON_L Active LOW signal which enables/disables the main output. Pulling this signal LOW will turn-on the main output. Recommended pull-up resistor to 12 VSB is 8.2 k with a 3.0 k pull-down to ground. A 100 pF decoupling capacitor is also recommended. MIN VIL Input logic level LOW VIH Input logic level HIGH ISOURCE Current that may be sourced by this pin ISINK Current that may be sunk by this pin at low state MAX 0.8 V 2.0 V 5.0 V 2 mA 0.5 mA PSKILL_L First break/last mate active LOW signal which enables/disables the main output. This signal will have to be pulled to ground at the system side with a 220 ohm resistor. A 100 pF decoupling capacitor is also recommended. MIN VIL Input logic level LOW VIH Input logic level HIGH ISOURCE Current that may be sourced by this pin ISINK Current that may be sunk by this pin at low state MAX 0.8 V 2.0 V 5.0 V 2 mA 0.5 mA DS500SPE Data Sheet Control and Status Signals Output Signals ACOK Signal used to indicate the presence of AC input to the power supply. A logic level HIGH will indicate that the AC input to the power supply is within the operating range while a logic level LOW will indicate that AC has been lost. This is an open collector/drain output. This pin is pulled high by a 1.0 kohm resistor connected to 3.3 V inside the power supply. It is recommended that this pin be connected to a 100 pF decoupling capacitor and pulled down by a 100 kohm resistor. MIN MAX VIL Input logic level LOW VIH Input logic level HIGH 0.6 V ISOURCE Current that may be sourced by this pin 3.3 mA ISINK Current that may be sunk by this pin at low state 0.7 mA 2.0 V 5.0 V PWR_GOOD/PWOK Signal used to indicate that main output voltage is within regulation range. The PWR_GOOD signal will be driven HIGH when the output voltage is valid and will be driven LOW when the output falls below the under-voltage threshold. This signal also gives an advance warning when there is an impending power loss due to loss of AC input or system shutdown request. More details in the Timing Section. This is an open collector/drain output. This pin is pulled high by a 1.0 kohm resistor connected to 3.3 V inside the power supply. It is recommended that this pin be connected to a 100 pF decoupling capacitor and pulled down by a 10 kohm resistor. MIN MAX VIL Input logic level LOW 0.8 V VIH Input logic level HIGH ISOURCE Current that may be sourced by this pin 3.3 mA ISINK Current that may be sunk by this pin at low state 0.7 mA 2.0 V 5.0 V PS_PRESENT Signal used to indicate to the system that a power supply is inserted in the power bay. This pin is shorted to the standby return in the power supply. Recommended pull-up resistor to 12 VSB is 8.2 k with a 3.0 k pull-down to ground. A 100 pF decoupling capacitor is also recommended. PS_INTERRUPT_L Active low signal used by the power supply to indicate to the system that a change in power supply status has occurred. This event can be triggered by faults such as OVP, OCP, OTP, and fan fault. This signal can be cleared by a CLEAR_FAULT command. Recommended pull-up resistor to 12 VSB is 8.2 k with a 3.0 k pull-down to ground. A 100 pF decoupling capacitor is also recommended. MIN MAX VIL Input logic level LOW VIH Input logic level HIGH 0.8 V ISOURCE Current that may be sourced by this pin 4 mA ISINK Current that may be sunk by this pin at low state 4 mA 2.0 V 5.0 V BUS Signals ISHARE Bus signal used by the power supply for active current sharing. All power supplies configured in the system for n+n sharing will refer to this bus voltage inorder to load share. Voltage Range The range of this signal for active sharing will be up to 8.0 V, which corresponds to the maximum output current. MIN MAX ISHARE Voltage Vshare at 100% load, stand-alone unit 7.75 8.25 Voltage at 50% load, stand-alone unit 3.85 4.15 Voltage at 0% load, stand-alone unit 0 ISOURCE Current that may be sourced by this pin 0.3 160 mA SCL, SDA Clock and data signals defined as per I2C requirements. It is recommended that these pins be pulled-up to a 2.2 kohm resistor to 3.3 V and a 100 pF decoupling capacitor at the system side. VL Input logic level LOW VH Input logic level HIGH 0.8 V 2.0 V Note: All signal noise levels are below 400 mVpk-pk from 0 - 100 MHz. I2C Addressing Table: Not applicable. This power supply has a fixed I2C address. In order to support multiple addresses, the system will have to utilize a switcher or an I2C expander. 5.0 V DS500SPE Data Sheet Electrical Specifications LED Indicators A single bi-color LED is used to indicate the power supply status. Status LED No AC input to PSU Off Main output ON Solid GREEN Standby mode or Power supply failure (OCP, OVP, OTP, FAN FAULT) Blinking AMBER Firmware Reporting And Monitoring Accuracy Range Output loading 5 to 20% 20 to 50% Input voltage 50 to 100% ±5% Input current ±0.55 A fixed error Input power ±6.25 W at <125 W input ±4% ±5% Output voltage ±2% Output current 1.5 A fixed error Temperature ±3% ±5 °C on the operating range EIN ±15% from 10% to 20% load Fan speed ±5% Actual RPM ±250 RPM PMBus YES Remote ON/OFF YES Timing Specifications Description Min Max Unit Tsb_On Delay from AC being applied to standby output being within regulation 20 2000 ms Tsb_ACOK Delay from standby output to ACOK assertion 20 ms Tsb_Vout Delay from standby output to main output voltage being within regulation 300 ms TAC_On_Delay Delay from AC being applied to main output being within regulation 2300 ms TPWR_GOOD_On Delay from output voltages within regulation limits to PWOK asserted 1000 ms TACOK_Delay Delay from loss of AC to assertion of ACOK 7 ms TPWR_GOOD_Hold-up Delay from loss of AC to deassertion of PWOK TVout_Hold-up Tsb_Hold-up TPWR_GOOD_Off Delay from deassertion of PWOK to output falling out of regulation TPSON_On_Delay Delay from PSON assertion to output being within regulation TPWOK_Low Duration of PWOK being in deasserted state during an ON/OFF cycle of PSU See note below 100 10 ms Delay from loss of AC to main output being within regulation 11 ms Delay from loss of AC to standby output being within regulation 150 ms 1 ms Note: Tvout_hold-up: tested at 1A load on standby output Tsb_ACOK: ACOK can assert earlier than the standby output 350 N/A N/A ms DS500SPE Data Sheet Timing Diagram AC Input Tsb_Hold-up Tsb_On TACOK_Delay Vout_stby Tsb_Vout Tsb_ACOK ACOK TAC_On_Delay TVout_Hold-up Vout_main TPWOK_On TPWOK_Off PWOK TPWOK_Hold-up TPSON_On_Delay PSON Environmental Specifications Operating temperature 0 to 50 °C, withstand operation up to 60 °C at 300 W output power without damage Operating altitude up to 10,000 feet at 35°C, 500W Operating relative humidity 10% to 95% non-condensing Non-operating temperature -40 to +70 °C Non-operating relative humidity 10% to 95% non-condensing Non-operating altitude up to 50,000 feet Vibration and shock Standard operating/non-operating random shock and vibration ROHS compliance Yes MTBF 500,000 hours per Telcordia Issue 2, Method 1, Case 3 at 50 °C at full load. Operating life Minimum of 5 years at typical conditions Reliability All electronic component derating analysis and capacitor life calculation is done at maximum ambient, 80% of maximum rated load, nominal input line voltage. DS500SPE Data Sheet Mechanical Outline 20 STD (FORWARD) AIRFLOW A 9±0.5 1,5 40,2 0,6 196,5±0.5 61,9 86,3±0.5 MODEL LABEL 15±0.3 9,5 190,9±0.5 A 4±0.2 2,9 14,2±0.8 49,5 8 A 9,4 38,5±0.5 9,3±0.3 17,8 A DS500SPE Data Sheet Connector Definitions Output Connector Part Number Mating Connector Part Number Output Connector Pin Configuration Card-edge FCI 10107844-002LF or equivalent Power Supply Output Card Edge (Bottom Side) S24 P29-P36 P21-28 S13 . . . P19/20 S1 PS PRESENT S13 PS_ON_L S2 Reserved S14 PS_KILL_L S3 Reserved S15 Reserved S4 Pwr_Good (PWOK) S16 RETURN S5 ACOK (AC Input Present) S17 SDA S6 RETURN S18 RETURN S7 ISHARE S19 SCL S8 RESERVE S20 RETURN S9 PS INTERRUPT_L S21 REMOTE SENSE- S10 RETURN S22 RETURN S11 Reserved S23 REMOTE SENSE+ S12 Reserved S24 RESERVE P1-P8 Vo P19-P20 VSB P9-P18 RTN P21-P28 RTN P29-P36 Vo Power Supply Output Card Edge (Top Side) P1-P8 P9-P18 . S1 . S12 WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 2900 S.Diablo Way Tempe, AZ 85282 USA +1 888 412 7832 Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom +44 (0) 1384 842 211 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong +852 2176 3333 Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2015 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal. www.artesyn.com For more information: www.artesyn.com/power For support: [email protected] DS500SPE DS 07Dec2015