Document 717 Shielded Coupled Inductor For Maxim MAX14521E • Developed for Maxim MAX14521E High-Voltage EL Lamp Driver with I²C Interface • Used as a 1 : 8 autotransformer • Shielded part for high-density applications Core material Ferrite Environmental RoHS compliant, halogen free optional Terminations RoHS compliant silver-palladium-platinum-glass frit. Weight 32 mg Ambient temperature –40°C to +85°C with Irms current, +85°C to +125°C with derated current Storage temperature Component: –40°C to +125°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Temperature Coefficient of Inductance (TCL) +50 to +150 ppm/°C Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 1000/7″ reel; 3500/13″ reel; Plastic tape: 12 mm wide, 0.23 mm thick, 8 mm pocket spacing, 1.4 mm pocket depth PCB washing Only pure water or alcohol recommended Dot indicates pin 1 Part number1 Inductance ±20% (µH)2 L1 L2 DCR max (Ohms) L1 L2 Turns ratio L1 : L2 Isat3 GA3250-BL_ 1.9 1.29 11.19 1:8 0.7 112 (A) 1. When ordering, please specify termination and packaging codes: GA3250-BLC Termination: L = RoHS compliant silver-palladium-platinum-glass frit. E = Halogen free component. RoHS compliant silverpalladium-platinum-glass frit terminations. Special order, added cost: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic tape (1000 parts per full reel). B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. D = 13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (3500 parts per full reel). 2. Inductance measured at 100 kHz, 0.1 Vrms, 0 Adc using an Agilent/ HP 4284A LCR meter or equivalent. 3. DC current at which the inductance of L1 drops 20% (typ) from its value without current. 4. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. 1 1 4 L1 0.116 ±0.003 2,95 ±0,08 3 2 Pins 2 and 4 to be connected on the PC board 2 4 L2 0.116 ±0.003 2,95 ±0,08 3 Recommended Land Pattern 0.036 ±0.004 0,9 ±0,1 0.022 0,54 1 4 3 2 45° typ 0.094 0.040 2,38 1,02 1 4 0.039 0,99 Dimensions are in inches mm 0.130 3,30 3 2 0.040 1,02 0.094 2,38 0.130 3,30 Cover area with solder mask. US +1-847-639-6400 [email protected] UK +44-1236-730595 [email protected] Taiwan +886-2-2264 3646 [email protected] China +86-21-6218 8074 [email protected] Singapore + 65-6484 8412 [email protected] Document 717 Revised 12/11/12 © Coilcraft Inc. 2012 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check out web site for latest information.