Finisar FTLF8524P2NV 4.25 gb/s rohs compliant short-wavelength sfp transceiver Datasheet

Product Specification
4.25 Gb/s RoHS Compliant Short-Wavelength SFP Transceiver
FTLF8524P2xNy
PRODUCT FEATURES
ƒ
Up to 4.25 Gb/s bi-directional
data links
ƒ
Hot-pluggable SFP footprint
ƒ
Built-in digital diagnostic functions
ƒ
850nm Oxide VCSEL laser
transmitter
ƒ
Duplex LC connector
ƒ
RoHS Compliant and Lead Free
ƒ
Up to 500m on 50/125μm MMF,
300m on 62.5/125μm MMF
ƒ
ƒ
Tri-Rate 1.063/2.125/4.25 Gb/s
Fibre Channel
Metal enclosure, for lower EMI
ƒ
ƒ
Single 3.3V power supply
1.25 Gb/s 1000Base-SX Ethernet
(Rate selectable version)
ƒ
Extended operating temperature
range: -20°C to 85°C
ƒ
Wireless – OBSAI, CPRI
APPLICATIONS
Finisar’s FTLF8524P2xNy Small Form Factor Pluggable (SFP) transceivers are
compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA)1.
They are compatible with Fibre Channel FC-PI-2 Rev. 7.02. Rate Selectable versions are
also compatible with Gigabit Ethernet as specified in IEEE Std 802.33. They are RoHS
compliant and lead-free per Directive 2002/95/EC4 and Finisar Application Note AN2038. Digital diagnostics functions are available via the 2-wire serial bus specified in the
SFP MSA.
PRODUCT SELECTION
FTLF8524P2xNy
x
y
W
B
L
V
Wide Extraction Bail
Narrow Extraction Bail
Non Rate Selectable - 1x, 2x, 4x Fibre Channel
Rate Selectable - 1x, 2x, 4x Fibre Channel and Gigabit Ethernet
© Finisar Corporation Jun 25, 2009 Rev.J
Page 1
FTLF8524P2xNy Pluggable SFP Product Specification – June 2009
I.
Pin Descriptions
Pin
1
2
3
4
5
6
7
Symbol
VEET
TFAULT
TDIS
MOD_DEF(2)
MOD_DEF(1)
MOD_DEF(0)
Rate Select
8
9
10
11
12
13
14
15
16
17
18
19
20
LOS
VEER
VEER
VEER
RDRD+
VEER
VCCR
VCCT
VEET
TD+
TDVEET
Name/Description
Transmitter Ground (Common with Receiver Ground)
Transmitter Fault.
Transmitter Disable. Laser output disabled on high or open.
Module Definition 2. Data line for Serial ID.
Module Definition 1. Clock line for Serial ID.
Module Definition 0. Grounded within the module.
Open or Low =
1.063 Gb/s or 2.125 Gb/s Fibre Channel, 1.25 Gb/s
Gigabit Ethernet (Low Bandwidth)
High =
2.125 or 4.25 Gb/s Fibre Channel (High Bandwidth)
Loss of Signal indication. Logic 0 indicates normal operation.
Receiver Ground (Common with Transmitter Ground)
Receiver Ground (Common with Transmitter Ground)
Receiver Ground (Common with Transmitter Ground)
Receiver Inverted DATA out. AC Coupled
Receiver Non-inverted DATA out. AC Coupled
Receiver Ground (Common with Transmitter Ground)
Receiver Power Supply
Transmitter Power Supply
Transmitter Ground (Common with Receiver Ground)
Transmitter Non-Inverted DATA in. AC Coupled.
Transmitter Inverted DATA in. AC Coupled.
Transmitter Ground (Common with Receiver Ground)
Ref.
1
2
3
3
3
4
5
1
1
1
1
1
1
Notes:
1. Circuit ground is internally isolated from chassis ground.
2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
3. Should be pulled up with 4.7k – 10kohms on host board to a voltage between 2.0V and 3.6V.
MOD_DEF(0) pulls line low to indicate module is plugged in.
4. For Rate Selectable version only: In accordance with SFF Committee SFF-8079 Draft Rev. 1.6,
Table 3. Note that rate select can also be set through 2-wire bus in accordance with SFF-84725 at Bit
3, Byte 110, Address A2h (note: writing ‘1’ selects full bandwidth operation). Rate select is the logic
OR of the input state of Rate Select Pin and 2-wire bus. Non Rate Selectable version can operate at 1x,
2x, 4x Fibre Channel independent of rate select pin setting.
5. LOS is open collector output. Should be pulled up with 4.7k – 10kohms on host board to a voltage
between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
1
Towards
Bezel
2
TXFault
3
TX Disable
4
MOD-DEF(2)
5
MOD-DEF(1)
6
MOD-DEF(0)
7
Rate Select
8
LOS
9
VeeR
10
VeeT
20
TD-
19
TD+
18
VeeT
17
VeeT
VccT
16
VccR
15
VeeR
14
RD+
13
RD-
12
VeeR
11
Towards
ASIC
VeeR
Diagram of Host Board Connector Block Pin Numbers and Names
© Finisar Corporation Jun 25, 2009 Rev.J
Page 2
FTLF8524P2xNy Pluggable SFP Product Specification – June 2009
II.
Absolute Maximum Ratings
Parameter
Maximum Supply Voltage
Storage Temperature
Case Operating Temperature
Relative Humidity
III.
Symbol
Vcc
TS
TA
RH
Min
-0.5
-40
-20
0
Typ
Max
4.0
85
85
85
Unit
V
°C
°C
%
Ref.
1
Electrical Characteristics (TA = -20 to 85 °C, VCC = 3.0 to 3.6 Volts)
Parameter
Supply Voltage
Supply Current
Transmitter
Input differential impedance
Single ended data input swing
Transmit Disable Voltage
Transmit Enable Voltage
Receiver
Single ended data output swing
Data output rise time
Data output fall time
Mask Margin
LOS Fault
LOS Normal
Power Supply Rejection
Deterministic Jitter Contribution @ 2.125 Gb/s
Determinstic Jitter Contribution @ 4.25 Gb/s
Total Jitter Contribution @ 2.125 Gb/s
Total Jitter Contribution @ 4.25 Gb/s
Symbol
Vcc
Icc
Rin
Vin,pp
VD
VEN
Min
3.0
Typ
180
Max
3.6
240
Unit
V
mA
Ref.
1200
Vcc
Vee+ 0.8
Ω
mV
V
V
2
3
4
550
120
120
mV
ps
ps
5
6
6
VccHOST
Vee+0.8
V
V
mVpp
ps
ps
ps
ps
7
7
8
9
9
10
10
100
150
2
Vee
Vout,pp
tr
tf
300
VLOS fault
VLOS norm
PSR
RX Δ DJ
2
Vee
100
350
40%
RX Δ TJ
51.7
23.5
122
61
Notes:
1. Non condensing.
2. Connected directly to TX data input pins. AC coupling from pins into laser driver IC.
3. We recommend <600mV for best EMI performance.
4. Or open circuit.
5. Into 100 ohms differential termination.
6. Unfiltered, 20 – 80 %
7. LOS is an open collector output. Should be pulled up with 4.7k – 10kohms on the host board. Normal
operation is logic 0; loss of signal is logic 1. Maximum pull-up voltage is 5.5V.
8. Receiver sensitivity is compliant with power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to
specified value applied through the recommended power supply filtering network.
9. Typical peak-to-peak jitter (=6*RMS width of Jitter).
10. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ
and Δ DJ. If measured with TJ-free data input signal. In actual application, output TJ will be given by:
TJ OUT = DJ IN + ΔDJ +
(TJ IN − DJ IN )2 + (ΔTJ − ΔDJ )2
© Finisar Corporation Jun 25, 2009 Rev.J
Page 3
FTLF8524P2xNy Pluggable SFP Product Specification – June 2009
IV.
Optical Characteristics (TOP = -20 to 85 °C, VCC = 3. 00 to 3.60 Volts)
Parameter
Transmitter
Output Opt. Pwr: 50 or 62.5 MMF
Optical Wavelength
Spectral Width
Optical Modulation Amplitude @ 4.25 Gb/s
Optical Modulation Amplitude @ 2.125 Gb/s
Optical Modulation Amplitude @ 1.0625 Gb/s
Optical Rise/Fall Time
Relative Intensity Noise
Deterministic Jitter Contribution @ 2.125 Gb/s
Deterministic Jitter Contribution @ 4.25 Gb/s
Total Jitter Contribution @ 2.125 Gb/s
Total Jitter Contribution @ 4.25 Gb/s
Extinction Ratio @ 1.25 Gb/s
Mask Margin
Receiver
Receiver Sensitivity = 1.0625 Gb/s
Receiver Sensitivity = 2.125 Gb/s
Receiver Sensitivity = 4.25 Gb/s
Receiver Sensitivity = 1.25 Gb/s
Stressed RX sens. =1.0625 Gb/s
Stressed RX sens. =2.125 Gb/s
Stressed Rx sens. = 4.25 Gb/s
Stressed RX sens. =1.25 Gb/s
Average Receiver Power
Receiver Elec. 3 dB cutoff frequency
Receiver Elec. 3 dB cutoff frequency
Optical Center Wavelength
Optical Return Loss
LOS De-Assert
LOS Assert
LOS Hysteresis
Symbol
Min
POUT
λ
σ
OMA
OMA
OMA
tr/ tf
RIN
TX Δ DJ
TX Δ DJ
TX Δ TJ
TX Δ TJ
ER
-9
830
Typ
Max
Unit
-2.5
860
0.85
dBm
nm
nm
μW
μW
μW
ps
dB/Hz
ps
ps
ps
ps
dB
247
196
156
90
-118
56.5
28.2
119
56.5
9
Ref.
1
2
2
2
3
4
4
5
5
6
45%
RxSENS
RxSENS
RxSENS
RxSENS
-20
-18
-15
-20
0.055
0.096
0.138
RxMAX
λC
LOSD
LOSA
770
12
-13.5
0
1500
2500
860
-20
-30
0.5
dBm
dBm
dBm
dBm
mW
mW
mW
dBm
dBm
MHz
MHz
nm
dB
dBm
dBm
dB
7
7
7
8
9
9
9
10
11
12
Notes:
1. Class 1 Laser Safety per FDA/CDRH, and EN (IEC) 60825 laser safety standards.
2. Equivalent extinction ratio specification for Fibre Channel. Allows smaller ER at higher average
power.
3. Unfiltered, 20-80%. Complies with FC 1x and 2x eye mask when filtered.
4. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ
and Δ DJ.
5. If measured with TJ-free data input signal. In actual application, output TJ will be given by:
TJ OUT = DJ IN + ΔDJ +
6.
7.
8.
9.
(TJ IN − DJ IN )2 + (ΔTJ − ΔDJ )2
Applicable for Rate Selectable version only in low bandwidth mode.
Specifications are for 50 micro-meter or 62.5 micro-meter fiber.
As measured with 9dB extinction ratio.
Measured with conformance signals defined in FC-PI-2 Rev. 7.0 specifications.
© Finisar Corporation Jun 25, 2009 Rev.J
Page 4
FTLF8524P2xNy Pluggable SFP Product Specification – June 2009
10. Measured with conformance signals defined in IEEE 802.3 specifications.
11. Rate Selectable version in low bandwidth mode.
12. Rate Selectable version in high bandwidth mode.
V.
General Specifications
Parameter
Data Rate
Symbol
BR
Bit Error Rate
Fiber Length on 50/125μm MMF
Min
Typ
1.062,
1.25,
2.125,
4.25
10-12
550
300
150
300
150
70
BER
L
L
Fiber Length on 62.5/125μm MMF
Max
Units
Gb/sec
m
m
Ref.
1
5
2
3
4
2
3
4
Notes:
1. 1x, 2x,4x Fibre Channel compatible, per FC-PI-2 Rev. 7.0. Rate selectable version is also Gigabit
Ethernet compatible per IEEE 802.3.
2. At 1.0625 Gb/s Fibre Channel data rate and, for rate selectable version, at 1.25 Gb/s Gigabit Ethernet
data rate.
3. At 2.125 Gb/s Fibre Channel data rate.
4. At 4.25 Gb/s Fibre Channel data rate
5. 4.25Gb/s with PRBS 27-1.
VI.
Environmental Specifications
Finisar 850nm SFP transceivers have an extended operating temperature range from
–20°C to +85°C case temperature.
Parameter
Case Operating Temperature
Storage Temperature
VII.
Symbol
Top
Tsto
Min
-20
-40
Typ
Max
85
85
Units
°C
°C
Ref.
Regulatory Compliance
Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations.
These products are certified by TÜV and CSA to meet the Class 1 eye safety
requirements of EN (IEC) 60825 and the electrical safety requirements of
EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request.
© Finisar Corporation Jun 25, 2009 Rev.J
Page 5
FTLF8524P2xNy Pluggable SFP Product Specification – June 2009
VIII. Digital Diagnostic Functions
Finisar FTLF8524P2xNy SFP transceivers support the 2-wire serial communication
protocol as defined in the SFP MSA1. It is very closely related to the E2PROM defined in
the GBIC standard, with the same electrical specifications.
The standard SFP serial ID provides access to identification information that describes
the transceiver’s capabilities, standard interfaces, manufacturer, and other information.
Additionally, Finisar SFP transceivers provide a enhanced digital diagnostic monitoring
interface, which allows real-time access to device operating parameters such as
transceiver temperature, laser bias current, transmitted optical power, received optical
power and transceiver supply voltage. It also defines a sophisticated system of alarm and
warning flags, which alerts end-users when particular operating parameters are outside of
a factory set normal range.
The SFP MSA defines a 256-byte memory map in E2PROM that is accessible over a
2-wire serial interface at the 8 bit address 1010000X (A0h). The digital diagnostic
monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally
defined serial ID memory map remains unchanged. The interface is identical to, and is
thus fully backward compatible with both the GBIC Specification and the SFP Multi
Source Agreement. The complete interface is described in Finisar Application Note AN2030: “Digital Diagnostics Monitoring Interface for SFP Optical Transceivers”.
The operating and diagnostics information is monitored and reported by a Digital
Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed
through a 2-wire serial interface. When the serial protocol is activated, the serial clock
signal (SCL, Mod Def 1) is generated by the host. The positive edge clocks data into the
SFP transceiver into those segments of the E2PROM that are not write-protected. The
negative edge clocks data from the SFP transceiver. The serial data signal (SDA, Mod
Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with
SCL to mark the start and end of serial protocol activation. The memories are organized
as a series of 8-bit data words that can be addressed individually or sequentially.
For more information, please see the SFP MSA documentation1,5 and Finisar Application
Note AN-2030.
Please note that evaluation board FDB-1018 is available with Finisar ModDEMO
software that allows simple to use communication over the 2-wire serial interface.
© Finisar Corporation Jun 25, 2009 Rev.J
Page 6
FTLF8524P2xNy Pluggable SFP Product Specification – June 2009
IX. Digital Diagnostic Specifications
FTLF8524P2xNy transceivers can be used in host systems that require either internally or
externally calibrated digital diagnostics.
Parameter
Symbol
Accuracy
DDTemperature
Internally measured transceiver
temperature
DDVoltage
Internally measured transceiver
supply voltage
DDBias
Measured TX bias current
DDTx-Power
Measured TX output power
DDRx-Power
Measured RX received average
optical power
Dynamic Range for Rated Accuracy
DDTemperature
Internally measured transceiver
temperature
DDVoltage
Internally measured transceiver
supply voltage
DDBias
Measured TX bias current
DDTx-Power
Measured TX output power
DDRx-Power
Measured RX received average
optical power
Max Reporting Range
DDTemperature
Internally measured transceiver
temperature
DDVoltage
Internally measured transceiver
supply voltage
DDBias
Measured TX bias current
DDTx-Power
Measured TX output power
DDRx-Power
Measured RX received average
optical power
Min
Typ
Max
Units
3
ºC
100
mV
10
2
2
%
dB
dB
-20
85
ºC
3.0
3.6
V
0
-9
-20
20
-2.5
0
mA
dBm
dBm
-40
125
ºC
2.8
4.0
V
0
-10
-22
20
-3
0
mA
dBm
dBm
Ref.
1
Notes:
1. Accuracy of Measured Tx Bias Current is 10% of the actual Bias Current from the laser driver to the
laser.
© Finisar Corporation Jun 25, 2009 Rev.J
Page 7
FTLF8524P2xNy Pluggable SFP Product Specification – June 2009
X.
Mechanical Specifications
Finisar’s Small Form Factor Pluggable (SFP) transceivers are compatible with the
dimensions defined by the SFP Multi-Sourcing Agreement (MSA).
FTLF8524P2BNy
© Finisar Corporation Jun 25, 2009 Rev.J
Page 8
FTLF8524P2xNy Pluggable SFP Product Specification – June 2009
FTLF8524P2WNy
© Finisar Corporation Jun 25, 2009 Rev.J
Page 9
FTLF8524P2xNy Pluggable SFP Product Specification – June 2009
XI. PCB Layout and Bezel Recommendations
© Finisar Corporation Jun 25, 2009 Rev.J
Page 10
FTLF8524P2xNy Pluggable SFP Product Specification – June 2009
© Finisar Corporation Jun 25, 2009 Rev.J
Page 11
FTLF8524P2xNy Pluggable SFP Product Specification – June 2009
XII.
References
1. Small Form-factor Pluggable (SFP) Transceiver Multi-source Agreement (MSA),
September 14, 2000.
2. “Fibre Channel Draft Physical Interface Specification (FC-PI-2 Rev. 7.0)”. American
National Standard for Information Systems.
3. IEEE Std 802.3, 2002 Edition, Clause 38, PMD Type 1000BASE-SX.
IEEE Standards Department, 2002.
4. Directive 2002/95/EC of the European Council Parliament and of the Council, “on
the restriction of the use of certain hazardous substances in electrical and electronic
equipment.” January 27, 2003.
5. “Digital Diagnostics Monitoring Interface for Optical Transceivers”. SFF Document
Number SFF-8472, Revision 9.3.
XIII. For More Information
Finisar Corporation
1308 Moffett Park Drive
Sunnyvale, CA 94089-1133
Tel. 1-408-548-1000
Fax 1-408-541-6138
[email protected]
www.finisar.com
© Finisar Corporation Jun 25, 2009 Rev.J
Page 12
Similar pages