AIMTEC AM40W-60012S-NZ 40 watt | dc-dc converter Datasheet

Series AM40W-NZ
40 Watt | DC-DC Converter
Picture coming soon
FEATURES:
•
•
•
•
Super wide 6:1 Input range
Extremely High Input range up to 1200VDC
High Input to Output Isolation of 4000VDC
Over current and Over Voltage protection
•
•
•
•
No minimum load required
High efficiency of up to 84%
Under Voltage Input protection
Reversed connection protection
Models
Single output
Model
Input Voltage
(V)
Output
Voltage
(V)
Output
Current max
(A)
Isolation
(VDC)
Max
Capacitive
Load(uF)
Efficiency
(200VDC) (%)
AM40W-60012S-NZ
AM40W-60015S-NZ
AM40W-60024S-NZ
200-1200
200-1200
200-1200
12
15
24
3.33
2.67
1.67
4000
4000
4000
1200
1000
680
83
84
84
NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at
rated output load unless otherwise specified.
Input Specifications
Parameters
Conditions
Typical
Voltage range
Input Current
Inrush current <2ms
External fuse
Input Under voltage lockout
200VDC
600VDC
1200VDC
600VDC
Slow blow
Maximum
Units
200-1200
320
100
55
VDC
60
3.15
175-185
mA
A
A
VDC
Isolation Specifications
Parameters
Tested I/O voltage
Conditions
Typical
1 min
4000
Maximum
Units
VDC
Output Specifications
Parameters
Voltage accuracy
Line voltage regulation
Load voltage regulation
Over voltage protection
Over current protection
Short Circuit protection
Short circuit restart
Temperature coefficient
Ripple & Noise
Hold up time
Conditions
Typical
±1
±0.5
±0.5
Zener diode clamp
LL-HL
0-100% load
Continuous
Auto recovery
±0.02
100
5
20MHz Bandwidth
600VDC
Maximum
Units
±2
±1
±1
%
% of Vin
%
110
% of Iout
200
%/ C
mV p-p
ms
Maximum
Units
95
KHz
°C
°C
°C
95
% RH
o
General Specifications
Parameters
Switching frequency
Operating temperature
Storage temperature
Maximum case temperature
Cooling
Humidity
Case material
Weight
www.aimtec.com
F 051e R13
Conditions
Typical
100% load
Derating above 50°C
65
-25 to 70
-25 to 85
Natural convection
Black plastic (UL94-V0)
210
Tel: +1 514 620 2722
1 of 3
g
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AM40W-NZ
40 Watt | DC-DC Converter
General Specifications (continued)
Parameters
Conditions
Dimensions (L x W x H)
MTBF
Maximum soldering temperature
Typical
Maximum
3.50 x 2.50 x 0.98 inches
89.00 x 63.50 x 25.00 mm
o
>300,000 hrs (MIL-HDBK -217F, Ground Benign, t=+25 C)
1.5mm from case for 5-10 sec
260
Units
o
C
Safety Specifications
Parameters
EMI - Conducted and radiated emission
Electrostatic Discharge Immunity
RF, Electromagnetic Field Immunity
Electrical Fast Transient/Burst Immunity
Surge Immunity
RF, Conducted Disturbance Immunity
Power frequency Magnetic Field Immunity
Voltage dips, Short Interruptions Immunity
Standards
EN55022, class A (with the recommended EMC circuit)
EN55024: 2010
IEC 61000-4-2: Contact ±6KV/Air ±8KV, Criteria B
IEC 61000-4-3: 10V/m, Criteria A
IEC 61000-4-4: ±4KV, Criteria B
IEC 61000-4-5: ±2KV, Criteria B
IEC 61000-4-6: 10Vrms, Criteria A
IEC 61000-4-8: 10A/m, Criteria A
IEC 61000-4-11: 0-70%, Criteria B
Pin Out Specifications
Pin
1
2
3
4
5
Single
+Vin
-Vin
+Vout
-Vout
N.C.
3.81
(0.15)
Dimensions
3.81
(0.15)
89.00
(3.50)
3
Top View
4
27.94
(1.10)
55.88
(2.20)
63.50
(2.50)
27.94
(1.10)
2
5
3.81
(0.15)
3.81
(0.15)
1
1.30
(0.05)
www.aimtec.com
F 051e R13
81.30
(3.20)
DIV: 10.00 (0.40)
3.85
(0.15)
5Ø 1.70 (Ø 0.07)
Dimensions mm (inch)
Case Tolerance ±0.50 (±0.02)
Pin Diameter ± 0.10 (± 0.004)
Side View
10.00
(0.40)
30.00
(1.18)
3.85
(0.15)
Tel: +1 514 620 2722
2 of 3
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AM40W-NZ
40 Watt | DC-DC Converter
Derating
Free Air Convection at 25°C
Free Air Convection
100
80
Output Power (%)
100
Safe Operating Area
200 – 1000VDC
60
40
20
80
Safe Operating Area
60
40
20
0
0
70
50
- 25
-20
0
20
40
60
200
100
80
1000 1200
Input Voltage VDC
Ambient Temperature º C
NOTE: 1. For Input Voltage between 1000-1200VDC the derating will depend on the temperature derating.
2. Sufficient air space for natural air flow around must be considered.
Typical Application circuit
+ Vin
Single Output
FUSE
3.15A
NTC
+
+ Vin
MOV
S20K1000
DC
- Vin
DC
C2
+ Vin
MOV
S20K1000
NTC
LCM
10mH
12 & 15
Vout
24 Vout
- Vout
TVS
20V
30V
Single Output
+
+
+
+
- Vin
Model
TVS
-
12 & 15 Vout
220 µF / 35V
24 Vout
120 µF / 35V
Recommended EMC Circuit
FUSE
3.15A
+
C1
C2
1µF/50V
- Vin
Model
+ Vout
C1
R1
C2
R2
C3
R3
C4
R4
+ Vout
+ Vin
DC
DC
- Vin
C1, C2, C3 &C4
47 µF/450V
+ Vout
C5
1µF/50V
C6
1MΩ / 2W
220 µF /
35V
120 µF /
35V
+
TVS
- Vout
- Vout
R1, R2, R3 & R4
C6
TVS
20V
30V
NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled
by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the
date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%,
nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components
and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This
product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate
specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com.
www.aimtec.com
F 051e R13
Tel: +1 514 620 2722
3 of 3
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Similar pages