ILPA35JUD SERIES 35W Dimmable Water-Proof Constant Current LED Driver – – – – – – – 3 Year Warranty Wide Input Voltage 90 to 305VAC, 47 to 63Hz Dimming Control, Constant Current Output Over Voltage, Short Circuit, Lighting, and Over Temperature Protection High Efficiency (up to 88%) Active Power Factor Correction (PFC) IP67 Waterproof Rating, Metal Housing Comply with UL8750 & EN61347 Safety Regulation Approvals: Single Output Output Current Range Output Voltage Range Efficiency Part Number (Min. / Typ. / Max.) (Min. / Max.) (220VAC, Full Load) ILPA35JUD-S290DT 2755 / 2900 / 3045 mA 4 / 12 VDC 82% ILPA35JUD-S245DT 2328 / 2450 / 2573 mA 5 / 15 VDC 83% ILPA35JUD-S210DT 1995 / 2100 / 2205 mA 6 / 18 VDC 84% ILPA35JUD-S175DT 1663 / 1750 / 1838 mA 7 / 20 VDC 84% ILPA35JUD-S140DT 1330 / 1400 / 1470 mA 8 / 24 VDC 85% ILPA35JUD-S105DT 998 / 1050 / 1103 mA 11 / 33 VDC 86% ILPA35JUD-S070DT 665 / 700 / 735 mA 17 / 50 VDC 86% ILPA35JUD-S045DT 428 / 450 / 473 mA 26 / 78 VDC 87% ILPA35JUD-S035DT 333 / 350 / 368 mA 33 / 100 VDC 88% Item -S290DT, -S245DT, -S210DT, -S175DT, -S140DT, -S105DT are Class 2 output (USR & CNR). Item -S070DT is Class 2 output (USR), Non-Class 2 output (CNR) Item -S045DT, -S035DT is Non-Class 2 output (USR & CNR) Over Voltage Protection (Min/Typ/Max) 13 / 15 / 17 VDC 16 / 18 / 20 VDC 19 / 21 / 23 VDC 23 / 25 / 27 VDC 30 / 32 / 34 VDC 39 / 41 / 43 VDC 57 / 58 / 59 VDC 95 / 97 / 99 VDC 118 / 120 / 122 VDC Max. Output Power 35W 35W 35W 35W 35W 35W 35W 35W 35W Electrical Characteristics Parameter Input Voltage Input Frequency Output Power Range Input Current (Low Line) Input Current (High Line) High Line Inrush Current Power Factor Correction Efficiency No-Load Power Consumption Line Regulation Load Regulation Over Voltage Protection Over Temperature Protection Short Circuit Protection Output Overshoot / Undershoot Start Up Time Ripple & Noise (Peak to Peak) Test Conditions Operating Voltage Min. 90 47 0 Typ. Max. 305 63 35 0.49 0.25 20 Unit VAC Hz W A A A % % W % % Vin=90 to 264VAC Io=Full load, Vin=115VAC Io=Full load, Vin=230VAC Io=Full load, 25°C, Cool start, Vin=230VAC Vin=110VAC 92 Io=Full Load, Vin=230VAC 82 88 No Load, VIn=230VAC 6 Io=Full Load 2 Vin=230VAC 5 (Latch mode. The power unit shall return to normal operation only after the power is turn-on again.) 110 °C No damage shall occur when any output operating in a short circuit condition. The power supply shall be self-recovery when the fault condition is removed. When power on or off 10 % Io=Full Load, Vin=110VAC 1.7 2 S Measured by 20 MHz bandwidth oscilloscope and the output paralleled a 0.1 uF ceramic capacitor and a 10 10 % Vo uF electrolytic capacitor. Conditions Parameter Test Conditions Operating Temperature Humidity: 10% RH to 100% RH Storage Temperature Humidity: 5% RH to 100% RH MTBF (Operation temperature at 25°C, calculated per MIL-HDBK-217F ) Life Time (measured at 110VAC, 45°C ambient temperature, 80% load for 2900mA output model) No output power derating from -35°C to 55°C Min. -35 -40 0.541M 0.087M Typ. Max. 55 85 Unit °C °C Hours Hours Approvals and Compliance Parameter EMI EMS Safety UL/c-UL, CE Waterproof Standards EN55015 EN61000-3-2, EN61000-3-3, EN61000-4-2, EN61000-4-3 , EN61000-4-4, , EN61000-4-5, EN61000-4-6, EN61000-4-8, EN61000-4-11, EN61547 UL8750 Compliant to UL1310 Class 2, UL1012, UL935, CSA-C22.2 No. 0, CSA-C22.2 No. 107.1, CSA-C22.2 No.250.0, EN61347-1,EN61347-2-13 IP67 Rating Mechanical Parameter Dimension, Net Weight Specification 172x34.5x42.5mm (6.77x1.36x1.67 inches) 480g Dimming Control Parameter Min. Typ. Max. Unit 10V Output Voltage 9.8 10V 10.2 VDC 10V Output Source Current -10 2 mA Absolute Max. Voltage on the 1~10V Input Pin -2 15 VDC Source Current on 0-10V Input Pin 0 1 mA The dimmer control may be operated from either a potentiometer or from an input signal of 0 ~ 10 Vdc. Two recommended implementations are provided above Notes: 1. For the driver to operate properly, the load voltage must be maintained above the minimum voltage threshold (approx. 33% of the max. output voltage for any given model). 2. If the input voltage is within 90-175Vac, the output current can be varied from 100% down to 10%. (Refer to right figure A) 3. If the input voltage is within 175-305Vac, the output current can be varied from 100% down to 20%. (Refer to right figure B)